[ Upstream commit c5b8d2c370 ]
The netc_blk_ctrl is controlled by the imx95-blk-ctl clock driver and
provides relevant clock configurations for NETC, SAI and MQS. Its address
length should be 8 bytes instead of 0x1000.
Fixes: 7764fef26e ("arm64: dts: imx95: Add NETCMIX block control support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e60b14f47d upstream.
For both the controller instances, size of the 'addr_space' region should
be 0x1fe00000 as per the hardware memory layout.
Otherwise, endpoint drivers cannot request even reasonable BAR size of 1MB.
Cc: stable@vger.kernel.org # 6.11
Fixes: c5f5de8434 ("arm64: dts: qcom: sa8775p: Add ep pcie1 controller node")
Fixes: 1924f55182 ("arm64: dts: qcom: sa8775p: Add ep pcie0 controller node")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241128145147.145618-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb8e7b33c2 upstream.
As per memory map table, the region for PCIe6a is 64MByte. Hence, set the
size of 32 bit non-prefetchable memory region beginning on address
0x70300000 as 0x3d00000 so that BAR space assigned to BAR registers can be
allocated from 0x70300000 to 0x74000000.
Fixes: 7af1418500 ("arm64: dts: qcom: x1e80100: Fix up BAR spaces")
Cc: stable@vger.kernel.org
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241113080508.3458849-1-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 058387d9c6 ]
Set the cache-line-size parameter of the L2 cache for each core to the
correct value of 64 bytes.
Previously, the L2 cache line size was incorrectly set to 128 bytes
for the Broadcom BCM2712. This causes validation tests for the
Performance Application Programming Interface (PAPI) tool to fail as
they depend on sysfs accurately reporting cache line sizes.
The correct value of 64 bytes is stated in the official documentation of
the ARM Cortex A-72, which is linked in the comments of
arm64/boot/dts/broadcom/bcm2712.dtsi as the source for cache-line-size.
Fixes: faa3381267 ("arm64: dts: broadcom: Add minimal support for Raspberry Pi 5")
Signed-off-by: Willow Cunningham <willow.e.cunningham@maine.edu>
Link: https://lore.kernel.org/r/20241007212954.214724-1-willow.e.cunningham@maine.edu
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 03c7527e97 upstream.
Catalin reports that a hypervisor lying to a guest about the size
of the ASID field may result in unexpected issues:
- if the underlying HW does only supports 8 bit ASIDs, the ASID
field in a TLBI VAE1* operation is only 8 bits, and the HW will
ignore the other 8 bits
- if on the contrary the HW is 16 bit capable, the ASID field
in the same TLBI operation is always 16 bits, irrespective of
the value of TCR_ELx.AS.
This could lead to missed invalidations if the guest was lead to
assume that the HW had 8 bit ASIDs while they really are 16 bit wide.
In order to avoid any potential disaster that would be hard to debug,
prenent the migration between a host with 8 bit ASIDs to one with
wider ASIDs (the converse was obviously always forbidden). This is
also consistent with what we already do for VMIDs.
If it becomes absolutely mandatory to support such a migration path
in the future, we will have to trap and emulate all TLBIs, something
that nobody should look forward to.
Fixes: d5a32b60dc ("KVM: arm64: Allow userspace to change ID_AA64MMFR{0-2}_EL1")
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Oliver Upton <oliver.upton@linux.dev>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20241203190236.505759-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6685f5d572 upstream.
commit 011e5f5bf5 ("arm64/cpufeature: Add remaining feature bits in
ID_AA64PFR0 register") exposed the MPAM field of AA64PFR0_EL1 to guests,
but didn't add trap handling. A previous patch supplied the missing trap
handling.
Existing VMs that have the MPAM field of ID_AA64PFR0_EL1 set need to
be migratable, but there is little point enabling the MPAM CPU
interface on new VMs until there is something a guest can do with it.
Clear the MPAM field from the guest's ID_AA64PFR0_EL1 and on hardware
that supports MPAM, politely ignore the VMMs attempts to set this bit.
Guests exposed to this bug have the sanitised value of the MPAM field,
so only the correct value needs to be ignored. This means the field
can continue to be used to block migration to incompatible hardware
(between MPAM=1 and MPAM=5), and the VMM can't rely on the field
being ignored.
Signed-off-by: James Morse <james.morse@arm.com>
Co-developed-by: Joey Gouly <joey.gouly@arm.com>
Signed-off-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241030160317.2528209-7-joey.gouly@arm.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
[maz: adapted to lack of ID_FILTERED()]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f82e62d470 ]
When enabling GICv4.1 in hip09, VMAPP fails to clear some caches during
the unmap operation, which can causes vSGIs to be lost.
To fix the issue, invalidate the related vPE cache through GICR_INVALLR
after VMOVP.
Suggested-by: Marc Zyngier <maz@kernel.org>
Co-developed-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 594bfc4947 upstream.
Currently poe_set() doesn't initialize the temporary 'ctrl' variable,
and a SETREGSET call with a length of zero will leave this
uninitialized. Consequently an arbitrary value will be written back to
target->thread.por_el0, potentially leaking up to 64 bits of memory from
the kernel stack. The read is limited to a specific slot on the stack,
and the issue does not provide a write mechanism.
Fix this by initializing the temporary value before copying the regset
from userspace, as for other regsets (e.g. NT_PRSTATUS, NT_PRFPREG,
NT_ARM_SYSTEM_CALL). In the case of a zero-length write, the existing
contents of POR_EL1 will be retained.
Before this patch:
| # ./poe-test
| Attempting to write NT_ARM_POE::por_el0 = 0x900d900d900d900d
| SETREGSET(nt=0x40f, len=8) wrote 8 bytes
|
| Attempting to read NT_ARM_POE::por_el0
| GETREGSET(nt=0x40f, len=8) read 8 bytes
| Read NT_ARM_POE::por_el0 = 0x900d900d900d900d
|
| Attempting to write NT_ARM_POE (zero length)
| SETREGSET(nt=0x40f, len=0) wrote 0 bytes
|
| Attempting to read NT_ARM_POE::por_el0
| GETREGSET(nt=0x40f, len=8) read 8 bytes
| Read NT_ARM_POE::por_el0 = 0xffff8000839c3d50
After this patch:
| # ./poe-test
| Attempting to write NT_ARM_POE::por_el0 = 0x900d900d900d900d
| SETREGSET(nt=0x40f, len=8) wrote 8 bytes
|
| Attempting to read NT_ARM_POE::por_el0
| GETREGSET(nt=0x40f, len=8) read 8 bytes
| Read NT_ARM_POE::por_el0 = 0x900d900d900d900d
|
| Attempting to write NT_ARM_POE (zero length)
| SETREGSET(nt=0x40f, len=0) wrote 0 bytes
|
| Attempting to read NT_ARM_POE::por_el0
| GETREGSET(nt=0x40f, len=8) read 8 bytes
| Read NT_ARM_POE::por_el0 = 0x900d900d900d900d
Fixes: 1751981992 ("arm64/ptrace: add support for FEAT_POE")
Cc: <stable@vger.kernel.org> # 6.12.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Joey Gouly <joey.gouly@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241205121655.1824269-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5d7129184 upstream.
Currently fpmr_set() doesn't initialize the temporary 'fpmr' variable,
and a SETREGSET call with a length of zero will leave this
uninitialized. Consequently an arbitrary value will be written back to
target->thread.uw.fpmr, potentially leaking up to 64 bits of memory from
the kernel stack. The read is limited to a specific slot on the stack,
and the issue does not provide a write mechanism.
Fix this by initializing the temporary value before copying the regset
from userspace, as for other regsets (e.g. NT_PRSTATUS, NT_PRFPREG,
NT_ARM_SYSTEM_CALL). In the case of a zero-length write, the existing
contents of FPMR will be retained.
Before this patch:
| # ./fpmr-test
| Attempting to write NT_ARM_FPMR::fpmr = 0x900d900d900d900d
| SETREGSET(nt=0x40e, len=8) wrote 8 bytes
|
| Attempting to read NT_ARM_FPMR::fpmr
| GETREGSET(nt=0x40e, len=8) read 8 bytes
| Read NT_ARM_FPMR::fpmr = 0x900d900d900d900d
|
| Attempting to write NT_ARM_FPMR (zero length)
| SETREGSET(nt=0x40e, len=0) wrote 0 bytes
|
| Attempting to read NT_ARM_FPMR::fpmr
| GETREGSET(nt=0x40e, len=8) read 8 bytes
| Read NT_ARM_FPMR::fpmr = 0xffff800083963d50
After this patch:
| # ./fpmr-test
| Attempting to write NT_ARM_FPMR::fpmr = 0x900d900d900d900d
| SETREGSET(nt=0x40e, len=8) wrote 8 bytes
|
| Attempting to read NT_ARM_FPMR::fpmr
| GETREGSET(nt=0x40e, len=8) read 8 bytes
| Read NT_ARM_FPMR::fpmr = 0x900d900d900d900d
|
| Attempting to write NT_ARM_FPMR (zero length)
| SETREGSET(nt=0x40e, len=0) wrote 0 bytes
|
| Attempting to read NT_ARM_FPMR::fpmr
| GETREGSET(nt=0x40e, len=8) read 8 bytes
| Read NT_ARM_FPMR::fpmr = 0x900d900d900d900d
Fixes: 4035c22ef7 ("arm64/ptrace: Expose FPMR via ptrace")
Cc: <stable@vger.kernel.org> # 6.9.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241205121655.1824269-3-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca62d90085 upstream.
Currently tagged_addr_ctrl_set() doesn't initialize the temporary 'ctrl'
variable, and a SETREGSET call with a length of zero will leave this
uninitialized. Consequently tagged_addr_ctrl_set() will consume an
arbitrary value, potentially leaking up to 64 bits of memory from the
kernel stack. The read is limited to a specific slot on the stack, and
the issue does not provide a write mechanism.
As set_tagged_addr_ctrl() only accepts values where bits [63:4] zero and
rejects other values, a partial SETREGSET attempt will randomly succeed
or fail depending on the value of the uninitialized value, and the
exposure is significantly limited.
Fix this by initializing the temporary value before copying the regset
from userspace, as for other regsets (e.g. NT_PRSTATUS, NT_PRFPREG,
NT_ARM_SYSTEM_CALL). In the case of a zero-length write, the existing
value of the tagged address ctrl will be retained.
The NT_ARM_TAGGED_ADDR_CTRL regset is only visible in the
user_aarch64_view used by a native AArch64 task to manipulate another
native AArch64 task. As get_tagged_addr_ctrl() only returns an error
value when called for a compat task, tagged_addr_ctrl_get() and
tagged_addr_ctrl_set() should never observe an error value from
get_tagged_addr_ctrl(). Add a WARN_ON_ONCE() to both to indicate that
such an error would be unexpected, and error handlnig is not missing in
either case.
Fixes: 2200aa7154 ("arm64: mte: ptrace: Add NT_ARM_TAGGED_ADDR_CTRL regset")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241205121655.1824269-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0900d15d3 upstream.
Linux currently sets the TCR_EL1.AS bit unconditionally during CPU
bring-up. On an 8-bit ASID CPU, this is RES0 and ignored, otherwise
16-bit ASIDs are enabled. However, if running in a VM and the hypervisor
reports 8-bit ASIDs (ID_AA64MMFR0_EL1.ASIDBits == 0) on a 16-bit ASIDs
CPU, Linux uses bits 8 to 63 as a generation number for tracking old
process ASIDs. The bottom 8 bits of this generation end up being written
to TTBR1_EL1 and also used for the ASID-based TLBI operations as the
upper 8 bits of the ASID. Following an ASID roll-over event we can have
threads of the same application with the same 8-bit ASID but different
generation numbers running on separate CPUs. Both TLB caching and the
TLBI operations will end up using different actual 16-bit ASIDs for the
same process.
A similar scenario can happen in a big.LITTLE configuration if the boot
CPU only uses 8-bit ASIDs while secondary CPUs have 16-bit ASIDs.
Ensure that the ASID generation is only tracked by bits 16 and up,
leaving bits 15:8 as 0 if the kernel uses 8-bit ASIDs. Note that
clearing TCR_EL1.AS is not sufficient since the architecture requires
that the top 8 bits of the ASID passed to TLBI instructions are 0 rather
than ignored in such configuration.
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241203151941.353796-1-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56a708742a upstream.
Commit ba0fb44aed ("dma-mapping: replace zone_dma_bits by
zone_dma_limit") and subsequent patches changed how zone_dma_limit is
calculated to allow a reduced ZONE_DMA even when RAM starts above 4GB.
Commit 122c234ef4 ("arm64: mm: keep low RAM dma zone") further fixed
this to ensure ZONE_DMA remains below U32_MAX if RAM starts below 4GB,
especially on platforms that do not have IORT or DT description of the
device DMA ranges. While zone boundaries calculation was fixed by the
latter commit, zone_dma_limit, used to determine the GFP_DMA flag in the
core code, was not updated. This results in excessive use of GFP_DMA and
unnecessary ZONE_DMA allocations on some platforms.
Update zone_dma_limit to match the actual upper bound of ZONE_DMA.
Fixes: ba0fb44aed ("dma-mapping: replace zone_dma_bits by zone_dma_limit")
Cc: <stable@vger.kernel.org> # 6.12.x
Reported-by: Yutang Jiang <jiangyutang@os.amperecomputing.com>
Tested-by: Yutang Jiang <jiangyutang@os.amperecomputing.com>
Signed-off-by: Yang Shi <yang@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20241125171650.77424-1-yang@os.amperecomputing.com
[catalin.marinas@arm.com: some tweaking of the commit log]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c5789c9d2 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: a39ed23bdf ("arm64: dts: freescale: add initial support for verdin imx8m plus")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbcc95fceb upstream.
The reset line of the IT6505 bridge chip is active low, not active high.
It was incorrectly inverted in the device tree as the implementation at
the time incorrectly inverted the polarity in its driver, due to a prior
device having an inline inverting level shifter.
Fix the polarity now while the external display pipeline is incomplete,
thereby avoiding any impact to running systems.
A matching fix for the driver should be included if this change is
backported.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241029100226.660263-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2213ca5199 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 316b80246b ("arm64: dts: ti: add verdin am62")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241024130628.49650-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ca7699c37 upstream.
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1aab0cb0 upstream.
The GPU SRAM supply is supposed to be always at least 0.1V higher than
the GPU supply. However when the DT was upstreamed, the spread was
incorrectly set to 0.01V.
Fixes: 8855d01fb8 ("arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool")
Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241021140537.3049232-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2496b2aaac upstream.
The way InvenSense MPU-6050 accelerometer is mounted on the user-facing side
of the Pine64 PinePhone mainboard, which makes it rotated 90 degrees counter-
clockwise, [1] requires the accelerometer's x- and y-axis to be swapped, and
the direction of the accelerometer's y-axis to be inverted.
Rectify this by adding a mount-matrix to the accelerometer definition in the
Pine64 PinePhone dtsi file.
[1] https://files.pine64.org/doc/PinePhone/PinePhone%20mainboard%20bottom%20placement%20v1.1%2020191031.pdf
Fixes: 91f480d409 ("arm64: dts: allwinner: Add initial support for Pine64 PinePhone")
Cc: stable@vger.kernel.org
Suggested-by: Ondrej Jirman <megi@xff.cz>
Suggested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Link: https://patch.msgid.link/129f0c754d071cca1db5d207d9d4a7bd9831dff7.1726773282.git.dsimic@manjaro.org
[wens@csie.org: Replaced Helped-by with Suggested-by]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26ea2459d1 upstream.
The Voltorb device uses a speaker codec different from the original
Corsola device. When the Voltorb device tree was first added, the new
codec was added as a separate node when it should have just replaced the
existing one.
Merge the two nodes. The only differences are the compatible string and
the GPIO line property name. This keeps the device node path for the
speaker codec the same across the MT8186 Chromebook line. Also rename
the related labels and node names from having rt1019p to speaker codec.
Cc: stable@vger.kernel.org # v6.11+
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20241018082113.1297268-1-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67ab51cbdf upstream.
Commit 18011eac28 ("arm64: tls: Avoid unconditional zeroing of
tpidrro_el0 for native tasks") tried to optimise the context switching
of tpidrro_el0 by eliding the clearing of the register when switching
to a native task with kpti enabled, on the erroneous assumption that
the kpti trampoline entry code would already have taken care of the
write.
Although the kpti trampoline does zero the register on entry from a
native task, the check in tls_thread_switch() is on the *next* task and
so we can end up leaving a stale, non-zero value in the register if the
previous task was 32-bit.
Drop the broken optimisation and zero tpidrro_el0 unconditionally when
switching to a native 64-bit task.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Fixes: 18011eac28 ("arm64: tls: Avoid unconditional zeroing of tpidrro_el0 for native tasks")
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20241114095332.23391-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9649129d3 upstream.
vgic_its_save_device_tables will traverse its->device_list to
save DTE for each device. vgic_its_restore_device_tables will
traverse each entry of device table and check if it is valid.
Restore if valid.
But when MAPD unmaps a device, it does not invalidate the
corresponding DTE. In the scenario of continuous saves
and restores, there may be a situation where a device's DTE
is not saved but is restored. This is unreasonable and may
cause restore to fail. This patch clears the corresponding
DTE when MAPD unmaps a device.
Cc: stable@vger.kernel.org
Fixes: 57a9a11715 ("KVM: arm64: vgic-its: Device table save/restore")
Co-developed-by: Shusen Li <lishusen2@huawei.com>
Signed-off-by: Shusen Li <lishusen2@huawei.com>
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
[Jing: Update with entry write helper]
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Link: https://lore.kernel.org/r/20241107214137.428439-5-jingzhangos@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7fe28d7e68 upstream.
In all the vgic_its_save_*() functinos, they do not check whether
the data length is 8 bytes before calling vgic_write_guest_lock.
This patch adds the check. To prevent the kernel from being blown up
when the fault occurs, KVM_BUG_ON() is used. And the other BUG_ON()s
are replaced together.
Cc: stable@vger.kernel.org
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
[Jing: Update with the new entry read/write helpers]
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Link: https://lore.kernel.org/r/20241107214137.428439-4-jingzhangos@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38d7aacca0 upstream.
Improper use of userspace_irqchip_in_use led to syzbot hitting the
following WARN_ON() in kvm_timer_update_irq():
WARNING: CPU: 0 PID: 3281 at arch/arm64/kvm/arch_timer.c:459
kvm_timer_update_irq+0x21c/0x394
Call trace:
kvm_timer_update_irq+0x21c/0x394 arch/arm64/kvm/arch_timer.c:459
kvm_timer_vcpu_reset+0x158/0x684 arch/arm64/kvm/arch_timer.c:968
kvm_reset_vcpu+0x3b4/0x560 arch/arm64/kvm/reset.c:264
kvm_vcpu_set_target arch/arm64/kvm/arm.c:1553 [inline]
kvm_arch_vcpu_ioctl_vcpu_init arch/arm64/kvm/arm.c:1573 [inline]
kvm_arch_vcpu_ioctl+0x112c/0x1b3c arch/arm64/kvm/arm.c:1695
kvm_vcpu_ioctl+0x4ec/0xf74 virt/kvm/kvm_main.c:4658
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl fs/ioctl.c:893 [inline]
__arm64_sys_ioctl+0x108/0x184 fs/ioctl.c:893
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x78/0x1b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0xe8/0x1b0 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x40/0x50 arch/arm64/kernel/syscall.c:151
el0_svc+0x54/0x14c arch/arm64/kernel/entry-common.c:712
el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:730
el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598
The following sequence led to the scenario:
- Userspace creates a VM and a vCPU.
- The vCPU is initialized with KVM_ARM_VCPU_PMU_V3 during
KVM_ARM_VCPU_INIT.
- Without any other setup, such as vGIC or vPMU, userspace issues
KVM_RUN on the vCPU. Since the vPMU is requested, but not setup,
kvm_arm_pmu_v3_enable() fails in kvm_arch_vcpu_run_pid_change().
As a result, KVM_RUN returns after enabling the timer, but before
incrementing 'userspace_irqchip_in_use':
kvm_arch_vcpu_run_pid_change()
ret = kvm_arm_pmu_v3_enable()
if (!vcpu->arch.pmu.created)
return -EINVAL;
if (ret)
return ret;
[...]
if (!irqchip_in_kernel(kvm))
static_branch_inc(&userspace_irqchip_in_use);
- Userspace ignores the error and issues KVM_ARM_VCPU_INIT again.
Since the timer is already enabled, control moves through the
following flow, ultimately hitting the WARN_ON():
kvm_timer_vcpu_reset()
if (timer->enabled)
kvm_timer_update_irq()
if (!userspace_irqchip())
ret = kvm_vgic_inject_irq()
ret = vgic_lazy_init()
if (unlikely(!vgic_initialized(kvm)))
if (kvm->arch.vgic.vgic_model !=
KVM_DEV_TYPE_ARM_VGIC_V2)
return -EBUSY;
WARN_ON(ret);
Theoretically, since userspace_irqchip_in_use's functionality can be
simply replaced by '!irqchip_in_kernel()', get rid of the static key
to avoid the mismanagement, which also helps with the syzbot issue.
Cc: <stable@vger.kernel.org>
Reported-by: syzbot <syzkaller@googlegroups.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7602ffd1d5 upstream.
When DISCARD frees an ITE, it does not invalidate the
corresponding ITE. In the scenario of continuous saves and
restores, there may be a situation where an ITE is not saved
but is restored. This is unreasonable and may cause restore
to fail. This patch clears the corresponding ITE when DISCARD
frees an ITE.
Cc: stable@vger.kernel.org
Fixes: eff484e029 ("KVM: arm64: vgic-its: ITT save and restore")
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
[Jing: Update with entry write helper]
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Link: https://lore.kernel.org/r/20241107214137.428439-6-jingzhangos@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e735a5da64 upstream.
Returning an abort to the guest for an unsupported MMIO access is a
documented feature of the KVM UAPI. Nevertheless, it's clear that this
plumbing has seen limited testing, since userspace can trivially cause a
WARN in the MMIO return:
WARNING: CPU: 0 PID: 30558 at arch/arm64/include/asm/kvm_emulate.h:536 kvm_handle_mmio_return+0x46c/0x5c4 arch/arm64/include/asm/kvm_emulate.h:536
Call trace:
kvm_handle_mmio_return+0x46c/0x5c4 arch/arm64/include/asm/kvm_emulate.h:536
kvm_arch_vcpu_ioctl_run+0x98/0x15b4 arch/arm64/kvm/arm.c:1133
kvm_vcpu_ioctl+0x75c/0xa78 virt/kvm/kvm_main.c:4487
__do_sys_ioctl fs/ioctl.c:51 [inline]
__se_sys_ioctl fs/ioctl.c:893 [inline]
__arm64_sys_ioctl+0x14c/0x1c8 fs/ioctl.c:893
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49
el0_svc_common+0x1e0/0x23c arch/arm64/kernel/syscall.c:132
do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151
el0_svc+0x38/0x68 arch/arm64/kernel/entry-common.c:712
el0t_64_sync_handler+0x90/0xfc arch/arm64/kernel/entry-common.c:730
el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:598
The splat is complaining that KVM is advancing PC while an exception is
pending, i.e. that KVM is retiring the MMIO instruction despite a
pending synchronous external abort. Womp womp.
Fix the glaring UAPI bug by skipping over all the MMIO emulation in
case there is a pending synchronous exception. Note that while userspace
is capable of pending an asynchronous exception (SError, IRQ, or FIQ),
it is still safe to retire the MMIO instruction in this case as (1) they
are by definition asynchronous, and (2) KVM relies on hardware support
for pending/delivering these exceptions instead of the software state
machine for advancing PC.
Cc: stable@vger.kernel.org
Fixes: da345174ce ("KVM: arm/arm64: Allow user injection of external data aborts")
Reported-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241025203106.3529261-2-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54bbee190d upstream.
DDI0487K.a D13.3.1 describes the PMU overflow condition, which evaluates
to true if any counter's global enable (PMCR_EL0.E), overflow flag
(PMOVSSET_EL0[n]), and interrupt enable (PMINTENSET_EL1[n]) are all 1.
Of note, this does not require a counter to be enabled
(i.e. PMCNTENSET_EL0[n] = 1) to generate an overflow.
Align kvm_pmu_overflow_status() with the reality of the architecture
and stop using PMCNTENSET_EL0 as part of the overflow condition. The
bug was discovered while running an SBSA PMU test [*], which only sets
PMCR.E, PMOVSSET<0>, PMINTENSET<0>, and expects an overflow interrupt.
Cc: stable@vger.kernel.org
Fixes: 76d883c4e6 ("arm64: KVM: Add access handler for PMOVSSET and PMOVSCLR register")
Link: https://github.com/ARM-software/sbsa-acs/blob/master/test_pool/pmu/operating_system/test_pmu001.c
Signed-off-by: Raghavendra Rao Ananta <rananta@google.com>
[ oliver: massaged changelog ]
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20241120005230.2335682-2-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5df3068441 ]
Comply with bindings guidelines and get rid of errors such as:
cpufreq@18323000: compatible: 'oneOf' conditional failed, one must be fixed:
['qcom,cpufreq-hw'] is too short
Fixes: 8575f197b0 ("arm64: dts: qcom: Introduce the SC8180x platform")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87cb58aebd ]
The callsite layout for arm64 fentry is:
mov x9, lr
nop
When a bpf prog is attached, the nop instruction is patched to a call
to bpf trampoline:
mov x9, lr
bl <bpf trampoline>
So two return addresses are passed to bpf trampoline: the return address
for the traced function/prog, stored in x9, and the return address for
the bpf trampoline itself, stored in lr. To obtain a full and accurate
call stack, the bpf trampoline constructs two fake function frames using
x9 and lr.
However, struct_ops progs are invoked directly as function callbacks,
meaning that x9 is not set as it is in the fentry callsite. In this case,
the frame constructed using x9 is garbage. The following stack trace for
struct_ops, captured by perf sampling, illustrates this issue, where
tcp_ack+0x404 is a garbage frame:
ffffffc0801a04b4 bpf_prog_50992e55a0f655a9_bpf_cubic_cong_avoid+0x98 (bpf_prog_50992e55a0f655a9_bpf_cubic_cong_avoid)
ffffffc0801a228c [unknown] ([kernel.kallsyms]) // bpf trampoline
ffffffd08d362590 tcp_ack+0x798 ([kernel.kallsyms]) // caller for bpf trampoline
ffffffd08d3621fc tcp_ack+0x404 ([kernel.kallsyms]) // garbage frame
ffffffd08d36452c tcp_rcv_established+0x4ac ([kernel.kallsyms])
ffffffd08d375c58 tcp_v4_do_rcv+0x1f0 ([kernel.kallsyms])
ffffffd08d378630 tcp_v4_rcv+0xeb8 ([kernel.kallsyms])
To fix it, construct only one frame using lr for struct_ops.
The above stack trace also indicates that there is no kernel symbol for
struct_ops bpf trampoline. This will be addressed in a follow-up patch.
Fixes: efc9909fdc ("bpf, arm64: Add bpf trampoline for arm64")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Acked-by: Puranjay Mohan <puranjay@kernel.org>
Tested-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20241025085220.533949-1-xukuohai@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42d8555752 ]
Correct the audio name for the Indiedroid Nova from
rockchip,es8388-codec to rockchip,es8388. This name change corrects a
kernel log error of "ASoC: driver name too long 'rockchip,es8388-codec'
-> 'rockchip_es8388'".
Fixes: 3900160e16 ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20241031150505.967909-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaecb1da58 ]
When the fixed regulators for the LCD panel and DP bridge were added,
their supplies were not modeled in. These, except for the 1.0V supply,
are just load switches, and need and have a supply.
Add the supplies for each of the fixed regulators.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241030070224.1006331-4-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4e8cf13f1 ]
Some of the regulator supplies for the MIPI-DPI-to-DP bridge and their
associated nodes are incorrectly named. In particular, the 1.0V supply
was modeled as a 1.2V supply.
Fix all the incorrect names, and also fix the voltage of the 1.0V
regulator.
Fixes: cabc71b08e ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20241030070224.1006331-3-wenst@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76ab2ae0ab ]
Fix DTBS check errors for 'mt6358codec' and 'mt6358regulator':
Error message is:
pmic: 'mt6358codec' and 'mt6358regulator' does not match any of the
regexes: 'pinctrl-[0-9]+'.
Rename these two device node to generic 'audio-codec' and 'regulators'.
Fixes: 9f88722216 ("arm64: dts: mt6358: add PMIC MT6358 related nodes")
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20241029064647.13370-1-macpaul.lin@mediatek.com
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c771d311b1 ]
Fix the issue where both 'output-low' and 'output-high' exist under GPIO
hog nodes (rst_usb_hub_hog and sel_usb_hub_hog) when applying device
tree overlays. Since /delete-property/ is not supported in the overlays,
setting 'output-low' results in both properties being present. The
workaround is to disable these hogs and create new ones with 'output-low'
as needed.
Fix below CHECK_DTBS warning:
arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx-usbotg.dtb: sel-usb-hub-hog:
{'output-low': True, 'gpio-hog': True, 'gpios': [[1, 0]], 'output-high': True, 'phandle': 108, '$nodename': ['sel-usb-hub-hog']}
is valid under each of {'required': ['output-low']}, {'required': ['output-high']
Fixes: 3f6fc30abe ("arm64: dts: imx8mn: tqma8mqnl-mba8mx: Add USB DR overlay")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc926e3fa ]
"#sound-dai-cells" is required if the board is using "simple-card".
However, the HiHope board uses "audio-graph", thus remove the unneeded
`#sound-dai-cells`.
Commit 9e72606cd2 ("arm64: dts: renesas: #sound-dai-cells is used when
simple-card") updated the comment regarding usage of "#sound-dai-cells"
in the SoC DTSI but missed to remove "#sound-dai-cells" from board DTS
files.
Fixes: 9e72606cd2 ("arm64: dts: renesas: #sound-dai-cells is used when simple-card")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/20241010135332.710648-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2473a3597 ]
__pa() is only intended to be used for linear map addresses and using
it for initial_boot_params which is in fixmap for arm64 will give an
incorrect value. Hence save the physical address when it is known at
boot time when calling early_init_dt_scan for arm64 and use it at kexec
time instead of converting the virtual address using __pa().
Note that arm64 doesn't need the FDT region reserved in the DT as the
kernel explicitly reserves the passed in FDT. Therefore, only a debug
warning is fixed with this change.
Reported-by: Breno Leitao <leitao@debian.org>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Usama Arif <usamaarif642@gmail.com>
Fixes: ac10be5cdb ("arm64: Use common of_kexec_alloc_and_setup_fdt()")
Link: https://lore.kernel.org/r/20241023171426.452688-1-usamaarif642@gmail.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e65616ef0 ]
Update the numbers based on the information found in the DSDT.
Fixes: af16b00578 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240716-topic-h_bits-v1-2-f6c5d3ff982c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a47e38167 ]
The clock IDs for multiple MCSPI instances across wakeup as
well as main domain in J7200 are incorrect when compared with
documentation [1]. This results in kernel crashes when the said
instances are enabled. Fix the clock ids to their appropriate
values.
[1]https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html
Fixes: 8f6c475f4c ("arm64: dts: ti: k3-j7200: Add MCSPI nodes")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Link: https://lore.kernel.org/r/20241023104532.3438851-2-a-dutta@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7af8b4acb ]
Commit 0d0a0b4413 ("arm64: dts: ti: k3-j7200: fix main pinmux
range") split the main_pmx0 into two nodes: main_pmx0 and main_pmx1
due to a non-addressable region, but incorrectly represented the
ranges. As a result, the memory map for the pinctrl is incorrect. Fix
this by introducing the correct ranges.
The ranges are taken from the J7200 TRM [1] (Table 5-695. CTRL_MMR0
Registers).
Padconfig starting addresses and ranges:
- 0 to 66: 0x11c000, 0x10c
- 68: 0x11c110, 0x004
- 71 to 73: 0x11c11c, 0x00c
- 89 to 90: 0x11c164, 0x008
The datasheet [2] doesn't contain PADCONFIG63 (Table 6-106. Pin
Multiplexing), but the pin is necessary for enabling the MMC1 CLKLP
pad loopback and should be included in the pinmux register map.
Due to the change in pinmux node addresses, change the pinmux node for
the USB0_DRVVBUS pin to main_pmx2. The offset has not changed since the
new main_pmx2 node has the same base address and range as the original
main_pmx1 node. All other pinmuxing done within J7200 dts or dtso files
only uses main_pmx0 which has not changed.
[1] https://www.ti.com/lit/pdf/spruiu1
[2] https://www.ti.com/lit/gpn/dra821u
Fixes: 0d0a0b4413 ("arm64: dts: ti: k3-j7200: fix main pinmux range")
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240926102533.398139-1-a-limaye@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9d7e6596 ]
The 'enable-active-low' property is not a valid, because it is the
default behaviour of the fixed regulator.
Only 'enable-active-high' is valid, and when this property is absent
the fixed regulator will act as active low by default.
Both the rk3588-orange-pi-5 and the Wolfvision pf5 io expander overlay
smuggled those enable-active-low properties in, so remove them to
make dtbscheck happier.
Fixes: 28799a7734 ("arm64: dts: rockchip: add wolfvision pf5 io expander board")
Cc: Michael Riesch <michael.riesch@wolfvision.net>
Fixes: b6bc755d80 ("arm64: dts: rockchip: Add Orange Pi 5")
Cc: Muhammed Efe Cetin <efectn@6tel.net>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-10-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e57d3dc7b ]
The dtschema requires to specify common ancestor which all SDIO chips are
derived from, so add accordingly.
Fixes: a50d5dcd28 ("arm64: tegra: Wire up WiFi on Jetson TX1 module")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409030438.8tumAnp1-lkp@intel.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d5794e6d9 ]
The RT5682i and RT5682s drivers describe two DAIs: AIF1 supports both
playback and capture, while AIF2 supports capture only.
Cherry doesn't specify which DAI to use. Although this doesn't cause
real issues because AIF1 happens to be the first DAI, it should be
corrected:
codec@1a: #sound-dai-cells: 1 was expected
Update #sound-dai-cells to 1 and adjust DAI link usages accordingly.
Fixes: 87728e3ccf ("arm64: dts: mediatek: mt8195-cherry: Specify sound DAI links and routing")
Signed-off-by: Fei Shao <fshao@chromium.org>
Link: https://lore.kernel.org/r/20241021114318.1358681-1-fshao@chromium.org
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
