[ Upstream commit b95102215a ]
Fix the suspend/resume path by ensuring the rtnl lock is held where
required. Calls to sh_eth_close, sh_eth_open and wol operations must be
performed under the rtnl lock to prevent conflicts with ongoing ndo
operations.
Fixes: b71af04676 ("sh_eth: add more PM methods")
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 752e5fcc2e ]
bgmac allocates new replacement buffer before handling each received
frame. Allocating & DMA-preparing 9724 B each time consumes a lot of CPU
time. Ideally bgmac should just respect currently set MTU but it isn't
the case right now. For now just revert back to the old limited frame
size.
This change bumps NAT masquerade speed by ~95%.
Since commit 8218f62c9c ("mm: page_frag: use initial zero offset for
page_frag_alloc_align()"), the bgmac driver fails to open its network
interface successfully and runs out of memory in the following call
stack:
bgmac_open
-> bgmac_dma_init
-> bgmac_dma_rx_skb_for_slot
-> netdev_alloc_frag
BGMAC_RX_ALLOC_SIZE = 10048 and PAGE_FRAG_CACHE_MAX_SIZE = 32768.
Eventually we land into __page_frag_alloc_align() with the following
parameters across multiple successive calls:
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=0
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=10048
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=20096
__page_frag_alloc_align: fragsz=10048, align_mask=-1, size=32768, offset=30144
So in that case we do indeed have offset + fragsz (40192) > size (32768)
and so we would eventually return NULL. Reverting to the older 1500
bytes MTU allows the network driver to be usable again.
Fixes: 8c7da63978 ("bgmac: configure MTU and add support for frames beyond 8192 byte size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[florian: expand commit message about recent commits]
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250127175159.1788246-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 044f2fbaa2 ]
Tx/Rx FIFO size is specified by the parameter "{tx,rx}-fifo-depth" from
stmmac_platform layer.
However, these values are constrained by upper limits determined by the
capabilities of each hardware feature. There is a risk that the upper
bits will be truncated due to the calculation, so it's appropriate to
limit them to the upper limit values and display a warning message.
This only works if the hardware capability has the upper limit values.
Fixes: e7877f52fd ("stmmac: Read tx-fifo-depth and rx-fifo-depth from the devicetree")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5fb35a3d6 ]
The number of MTL queues to use is specified by the parameter
"snps,{tx,rx}-queues-to-use" from stmmac_platform layer.
However, the maximum numbers of queues are constrained by upper limits
determined by the capability of each hardware feature. It's appropriate
to limit the values not to exceed the upper limit values and display
a warning message.
This only works if the hardware capability has the upper limit values.
Fixes: d976a525c3 ("net: stmmac: multiple queues dt configuration")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e43ad7a1e ]
Ethtool ntuple filters with FLOW_RSS were originally defined as adding
the base queue ID (ring_cookie) to the value from the indirection table,
so that the same table could distribute over more than one set of queues
when used by different filters.
However, some drivers / hardware ignore the ring_cookie, and simply use
the indirection table entries as queue IDs directly. Thus, for drivers
which have not opted in by setting ethtool_ops.cap_rss_rxnfc_adds to
declare that they support the original (addition) semantics, reject in
ethtool_set_rxnfc any filter which combines FLOW_RSS and a nonzero ring.
(For a ring_cookie of zero, both behaviours are equivalent.)
Set the cap bit in sfc, as it is known to support this feature.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://patch.msgid.link/cc3da0844083b0e301a33092a6299e4042b65221.1731499022.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f5a52adeb ("ethtool: Fix set RXNFC command with symmetric RSS hash")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e65c45a1 ]
dm is netdev private data and it cannot be
used after free_netdev() call. Using dm after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
This is similar to the issue fixed in commit
ad297cd2db ("net: qcom/emac: fix UAF in emac_remove").
This bug is detected by our static analysis tool.
Fixes: cf9e60aa69 ("net: davicom: Fix regulator not turned off on driver removal")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
CC: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20250123214213.623518-1-chenyuan0y@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee7d79433d ]
First case:
> ip l a l $VF name vlanx type vlan id 100
> ip l d vlanx
> ip l a l $VF name vlanx type vlan id 100
As workqueue can be execute after sometime, there is a window to have
call trace like that:
- iavf_del_vlan
- iavf_add_vlan
- iavf_del_vlans (wq)
It means that our VLAN 100 will change the state from IAVF_VLAN_ACTIVE
to IAVF_VLAN_REMOVE (iavf_del_vlan). After that in iavf_add_vlan state
won't be changed because VLAN 100 is on the filter list. The final
result is that the VLAN 100 filter isn't added in hardware (no
iavf_add_vlans call).
To fix that change the state if the filter wasn't removed yet directly
to active. It is save as IAVF_VLAN_REMOVE means that virtchnl message
wasn't sent yet.
Second case:
> ip l a l $VF name vlanx type vlan id 100
Any type of VF reset ex. change trust
> ip l s $PF vf $VF_NUM trust on
> ip l d vlanx
> ip l a l $VF name vlanx type vlan id 100
In case of reset iavf driver is responsible for readding all filters
that are being used. To do that all VLAN filters state are changed to
IAVF_VLAN_ADD. Here is even longer window for changing VLAN state from
kernel side, as workqueue isn't called immediately. We can have call
trace like that:
- changing to IAVF_VLAN_ADD (after reset)
- iavf_del_vlan (called from kernel ops)
- iavf_del_vlans (wq)
Not exsisitng VLAN filters will be removed from hardware. It isn't a
bug, ice driver will handle it fine. However, we can have call trace
like that:
- changing to IAVF_VLAN_ADD (after reset)
- iavf_del_vlan (called from kernel ops)
- iavf_add_vlan (called from kernel ops)
- iavf_del_vlans (wq)
With fix for previous case we end up with no VLAN filters in hardware.
We have to remove VLAN filters if the state is IAVF_VLAN_ADD and delete
VLAN was called. It is save as IAVF_VLAN_ADD means that virtchnl message
wasn't sent yet.
Fixes: 0c0da0e951 ("iavf: refactor VLAN filter states")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5cc2a27e0 ]
It occurred that in the commit 70838938e8 ("ice: Implement driver
functionality to dump serdes equalizer values") the invalid DRATE parameter
for reading has been added. The output of the command:
$ ethtool -d <ethX>
returns the garbage value in the place where DRATE value should be
stored.
Remove mentioned parameter to prevent return of corrupted data to
userspace.
Fixes: 70838938e8 ("ice: Implement driver functionality to dump serdes equalizer values")
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99dbcab0cd ]
Extend the work done in commit 70838938e8 ("ice: Implement driver
functionality to dump serdes equalizer values") by adding the new set of
Rx registers that can be read using command:
$ ethtool -d interface_name
Rx equalization parameters are E810 PHY registers used by end user to
gather information about configuration and status to debug link and
connection issues in the field.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c5cc2a27e0 ("ice: remove invalid parameter of equalizer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ea085937d ]
Refactor function ice_get_tx_rx_equa() to iterate over new table of
params instead of multiple calls to ice_aq_get_phy_equalization().
Subsequent commit will extend that function by add more serdes equalizer
values to dump.
Shorten the fields of struct ice_serdes_equalization_to_ethtool for
readability purposes.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: c5cc2a27e0 ("ice: remove invalid parameter of equalizer")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18625e26fe ]
Fix &ice_parser_rt::bst_key size. It was wrongly set to 10 instead of 20
in the initial impl commit (see Fixes tag). All usage code assumed it was
of size 20. That was also the initial size present up to v2 of the intro
series [2], but halved by v3 [3] refactor described as "Replace magic
hardcoded values with macros." The introducing series was so big that
some ugliness was unnoticed, same for bugs :/
ICE_BST_KEY_TCAM_SIZE and ICE_BST_TCAM_KEY_SIZE were differing by one.
There was tmp variable @j in the scope of edited function, but was not
used in all places. This ugliness is now gone.
I'm moving ice_parser_rt::pg_prio a few positions up, to fill up one of
the holes in order to compensate for the added 10 bytes to the ::bst_key,
resulting in the same size of the whole as prior to the fix, and minimal
changes in the offsets of the fields.
Extend also the debug dump print of the key to cover all bytes. To not
have string with 20 "%02x" and 20 params, switch to
ice_debug_array_w_prefix().
This fix obsoletes Ahmed's attempt at [1].
[1] https://lore.kernel.org/intel-wired-lan/20240823230847.172295-1-ahmed.zaki@intel.com
[2] https://lore.kernel.org/intel-wired-lan/20230605054641.2865142-13-junfeng.guo@intel.com
[3] https://lore.kernel.org/intel-wired-lan/20230817093442.2576997-13-junfeng.guo@intel.com
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/intel-wired-lan/b1fb6ff9-b69e-4026-9988-3c783d86c2e0@stanley.mountain
Fixes: 9a4c07aaa0 ("ice: add parser execution main loop")
CC: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a5b021cb8 ]
When a workqueue is created with `WQ_UNBOUND`, its work items are
served by special worker-pools, whose host workers are not bound to
any specific CPU. In the default configuration (i.e. when
`queue_delayed_work` and friends do not specify which CPU to run the
work item on), `WQ_UNBOUND` allows the work item to be executed on any
CPU in the same node of the CPU it was enqueued on. While this
solution potentially sacrifices locality, it avoids contention with
other processes that might dominate the CPU time of the processor the
work item was scheduled on.
This is not just a theoretical problem: in a particular scenario
misconfigured process was hogging most of the time from CPU0, leaving
less than 0.5% of its CPU time to the kworker. The IDPF workqueues
that were using the kworker on CPU0 suffered large completion delays
as a result, causing performance degradation, timeouts and eventual
system crash.
Tested:
* I have also run a manual test to gauge the performance
improvement. The test consists of an antagonist process
(`./stress --cpu 2`) consuming as much of CPU 0 as possible. This
process is run under `taskset 01` to bind it to CPU0, and its
priority is changed with `chrt -pQ 9900 10000 ${pid}` and
`renice -n -20 ${pid}` after start.
Then, the IDPF driver is forced to prefer CPU0 by editing all calls
to `queue_delayed_work`, `mod_delayed_work`, etc... to use CPU 0.
Finally, `ktraces` for the workqueue events are collected.
Without the current patch, the antagonist process can force
arbitrary delays between `workqueue_queue_work` and
`workqueue_execute_start`, that in my tests were as high as
`30ms`. With the current patch applied, the workqueue can be
migrated to another unloaded CPU in the same node, and, keeping
everything else equal, the maximum delay I could see was `6us`.
Fixes: 0fe45467a1 ("idpf: add create vport and netdev configuration")
Signed-off-by: Marco Leogrande <leogrande@google.com>
Signed-off-by: Manoj Vishwanathan <manojvishy@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15fe4edd7 ]
The transaction salt was being accessed before acquiring the
idpf_vc_xn_lock when idpf has to forward the virtchnl reply.
Fixes: 34c21fa894 ("idpf: implement virtchnl transaction manager")
Signed-off-by: Manoj Vishwanathan <manojvishy@google.com>
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 137da75ba7 ]
Restore the call to idpf_vc_xn_shutdown() at the beginning of
idpf_vc_core_deinit() provided the function is not called on remove.
In the reset path the mailbox is destroyed, leading to all transactions
timing out.
Fixes: 09d0fb5cb3 ("idpf: deinit virtchnl transaction manager after vport and vectors")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 396f016567 ]
Add read memory barrier to ensure the order of operations when accessing
control queue descriptors. Specifically, we want to avoid cases where loads
can be reordered:
1. Load #1 is dispatched to read descriptor flags.
2. Load #2 is dispatched to read some other field from the descriptor.
3. Load #2 completes, accessing memory/cache at a point in time when the DD
flag is zero.
4. NIC DMA overwrites the descriptor, now the DD flag is one.
5. Any fields loaded before step 4 are now inconsistent with the actual
descriptor state.
Add read memory barrier between steps 1 and 2, so that load #2 is not
executed until load #1 has completed.
Fixes: 8077c72756 ("idpf: add controlq init and reset checks")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Suggested-by: Lance Richardson <rlance@google.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92e5995773 ]
When unload hclge driver, it tries to disable sriov first for each
ae_dev node from hnae3_ae_dev_list. If user unloads hns3 driver at
the time, because it removes all the ae_dev nodes, and it may cause
oops.
But we can't simply use hnae3_common_lock for this. Because in the
process flow of pci_disable_sriov(), it will trigger the remove flow
of VF, which will also take hnae3_common_lock.
To fixes it, introduce a new mutex to protect the unload process.
Fixes: 0dd8a25f35 ("net: hns3: disable sriov before unload hclge layer")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250118094741.3046663-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d31a49d37c ]
Fix wrong GDM4 register definition, in Airoha SDK GDM4 is defined at
offset 0x2400 but this doesn't make sense as it does conflict with the
CDM4 that is in the same location.
Following the pattern where each GDM base is at the FWD_CFG, currently
GDM4 base offset is set to 0x2500. This is correct but REG_GDM4_FWD_CFG
and REG_GDM4_SRC_PORT_SET are still using the SDK reference with the
0x2400 offset. Fix these 2 define by subtracting 0x100 to each register
to reflect the real address location.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250120154148.13424-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4395a44acb ]
When getting the IRQ we use k3_udma_glue_tx_get_irq() which returns
negative error value on error. So not NULL check is not sufficient
to deteremine if IRQ is valid. Check that IRQ is greater then zero
to ensure it is valid.
There is no issue at probe time but at runtime user can invoke
.set_channels which results in the following call chain.
am65_cpsw_set_channels()
am65_cpsw_nuss_update_tx_rx_chns()
am65_cpsw_nuss_remove_tx_chns()
am65_cpsw_nuss_init_tx_chns()
At this point if am65_cpsw_nuss_init_tx_chns() fails due to
k3_udma_glue_tx_get_irq() then tx_chn->irq will be set to a
negative value.
Then, at subsequent .set_channels with higher channel count we
will attempt to free an invalid IRQ in am65_cpsw_nuss_remove_tx_chns()
leading to a kernel warning.
The issue is present in the original commit that introduced this driver,
although there, am65_cpsw_nuss_update_tx_rx_chns() existed as
am65_cpsw_nuss_update_tx_chns().
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70d81f25cc ]
Currently, mlxfw kernel module limits FW flash image size to be
10MB at most, preventing the ability to burn recent BlueField-3
FW that exceeds the said size limit.
Thus, drop the hard coded limit. Instead, rely on FW's
max_component_size threshold that is reported in MCQI register
as the size limit for FW image.
Fixes: 410ed13cae ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1737030796-1441634-1-git-send-email-moshe@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3440fa34ad ]
Following fields of 'struct mr_mfc' can be updated
concurrently (no lock protection) from ip_mr_forward()
and ip6_mr_forward()
- bytes
- pkt
- wrong_if
- lastuse
They also can be read from other functions.
Convert bytes, pkt and wrong_if to atomic_long_t,
and use READ_ONCE()/WRITE_ONCE() for lastuse.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20250114221049.1190631-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c7469ee71 ]
Do not run napi_disable() if airoha_hw_init() fails since Tx/Rx napi
has not been started yet. In order to fix the issue, introduce
airoha_qdma_stop_napi routine and remove napi_disable in
airoha_hw_cleanup().
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20241216-airoha_probe-error-path-fix-v2-1-6b10e04e9a5c@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6be7aca910 upstream.
In 4.19, before the switch to linkmode bitmaps, PHY_GBIT_FEATURES
included feature bits for aneg and TP/MII ports.
SUPPORTED_TP | \
SUPPORTED_MII)
SUPPORTED_10baseT_Full)
SUPPORTED_100baseT_Full)
SUPPORTED_1000baseT_Full)
PHY_100BT_FEATURES | \
PHY_DEFAULT_FEATURES)
PHY_1000BT_FEATURES)
Referenced commit expanded PHY_GBIT_FEATURES, silently removing
PHY_DEFAULT_FEATURES. The removed part can be re-added by using
the new PHY_GBIT_FEATURES definition.
Not clear to me is why nobody seems to have noticed this issue.
I stumbled across this when checking what it takes to make
phy_10_100_features_array et al private to phylib.
Fixes: d0939c26c5 ("net: ethernet: xgbe: expand PHY_GBIT_FEAUTRES")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/46521973-7738-4157-9f5e-0bb6f694acba@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f95b02477 ]
According to RFC4303, section "3.3.3. Sequence Number Generation",
the first packet sent using a given SA will contain a sequence
number of 1.
This is applicable to both ESN and non-ESN mode, which was not covered
in commit mentioned in Fixes line.
Fixes: 3d42c8cc67 ("net/mlx5e: Ensure that IPsec sequence packet number starts from 1")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f23524df ]
All packet offloads SAs have reqid in it to make sure they have
corresponding policy. While it is not strictly needed for transparent
mode, it is extremely important in tunnel mode. In that mode, policy and
SAs have different match criteria.
Policy catches the whole subnet addresses, and SA catches the tunnel gateways
addresses. The source address of such tunnel is not known during egress packet
traversal in flow steering as it is added only after successful encryption.
As reqid is required for packet offload and it is unique for every SA,
we can safely rely on it only.
The output below shows the configured egress policy and SA by strongswan:
[leonro@vm ~]$ sudo ip x s
src 192.169.101.2 dst 192.169.101.1
proto esp spi 0xc88b7652 reqid 1 mode tunnel
replay-window 0 flag af-unspec esn
aead rfc4106(gcm(aes)) 0xe406a01083986e14d116488549094710e9c57bc6 128
anti-replay esn context:
seq-hi 0x0, seq 0x0, oseq-hi 0x0, oseq 0x0
replay_window 1, bitmap-length 1
00000000
crypto offload parameters: dev eth2 dir out mode packet
[leonro@064 ~]$ sudo ip x p
src 192.170.0.0/16 dst 192.170.0.0/16
dir out priority 383615 ptype main
tmpl src 192.169.101.2 dst 192.169.101.1
proto esp spi 0xc88b7652 reqid 1 mode tunnel
crypto offload parameters: dev eth2 mode packet
Fixes: b3beba1fb4 ("net/mlx5e: Allow policies with reqid 0, to support IKE policy holes")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2011a2a18e ]
If failed to add SF, error handling doesn't delete the SF from the
SF table. But the hw resources are deleted. So when unload driver,
hw resources will be deleted again. Firmware will report syndrome
0x68def3 which means "SF is not allocated can not deallocate".
Fix it by delete SF from SF table if failed to add SF.
Fixes: 2597ee190b ("net/mlx5: Call mlx5_sf_id_erase() once in mlx5_sf_dealloc()")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c08d3e62b2 ]
User added steering rules at RDMA_TX were being added to the first prio,
which is the counters prio.
Fix that so that they are correctly added to the BYPASS_PRIO instead.
Fixes: 24670b1a31 ("net/mlx5: Add support for RDMA TX steering")
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 001ba09020 ]
The fec_enet_update_cbd function calls page_pool_dev_alloc_pages but did
not handle the case when it returned NULL. There was a WARN_ON(!new_page)
but it would still proceed to use the NULL pointer and then crash.
This case does seem somewhat rare but when the system is under memory
pressure it can happen. One case where I can duplicate this with some
frequency is when writing over a smbd share to a SATA HDD attached to an
imx6q.
Setting /proc/sys/vm/min_free_kbytes to higher values also seems to solve
the problem for my test case. But it still seems wrong that the fec driver
ignores the memory allocation error and can crash.
This commit handles the allocation error by dropping the current packet.
Fixes: 95698ff617 ("net: fec: using page pool to manage RX buffers")
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250113154846.1765414-1-kgroeneveld@lenbrook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c17ff476f5 ]
If coalesce_count is greater than 255 it will not fit in the register and
will overflow. This can be reproduced by running
# ethtool -C ethX rx-frames 256
which will result in a timeout of 0us instead. Fix this by checking for
invalid values and reporting an error.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20250113163001.2335235-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16ebb6f5b6 ]
The "sizeof(struct cmsg_bpf_event) + pkt_size + data_size" math could
potentially have an integer wrapping bug on 32bit systems. Check for
this and return an error.
Fixes: 9816dd35ec ("nfp: bpf: perf event output helpers support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/6074805b-e78d-4b8a-bf05-e929b5377c28@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 258f5f9058 ]
Driver always naively assumes, that for PTP purposes, PHY lane to
configure is corresponding to PF ID.
This is not true for some port configurations, e.g.:
- 2x50G per quad, where lanes used are 0 and 2 on each quad, but PF IDs
are 0 and 1
- 100G per quad on 2 quads, where lanes used are 0 and 4, but PF IDs are
0 and 1
Use correct PHY lane assignment by getting and parsing port options.
This is read from the NVM by the FW and provided to the driver with
the indication of active port split.
Remove ice_is_muxed_topo(), which is no longer needed.
Fixes: 4409ea1726 ("ice: Adjust PTP init for 2x50G E825C devices")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Arkadiusz Kubalewski <Arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e800654e85 ]
Use struct ice_adapter to hold shared PTP data and control PTP
related actions instead of auxbus. This allows significant code
simplification and faster access to the container fields used in
the PTP support code.
Move the PTP port list to the ice_adapter container to simplify
the code and avoid race conditions which could occur due to the
synchronous nature of the initialization/access and
certain memory saving can be achieved by moving PTP data into
the ice_adapter itself.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 258f5f9058 ("ice: Add correct PHY lane assignment")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97ed20a01f ]
Add ice_get_ctrl_ptp() wrapper to simplify the PTP support code
in the functions that do not use ctrl_pf directly.
Add the control PF pointer to struct ice_adapter
Rearrange fields in struct ice_adapter
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 258f5f9058 ("ice: Add correct PHY lane assignment")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e60560f1e ]
Fix ETH56G FC-FEC incorrect Rx offset value by changing it from -255.96
to -469.26 ns.
Those values are derived from HW spec and reflect internal delays.
Hex value is a fixed point representation in Q23.9 format.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc26548d72 ]
Quad registers are read/written incorrectly. E825 devices always use
quad 0 address and differentiate between the PHYs by changing SBQ
destination device (phy_0 or phy_0_peer).
Add helpers for reading/writing PTP registers shared per quad and use
correct quad address and SBQ destination device based on port.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d79c304c76 ]
Current implementation checks revision of all PHYs on all PFs, which is
incorrect and may result in initialization failure. Check only the
revision of the current PHY.
Fixes: 7cab44f1c3 ("ice: Introduce ETH56G PHY model for E825C products")
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7e441a410 ]
When tx_max_frame_size was added to struct ravb_hw_info, no value was
set in ravb_rzv2m_hw_info so the default value of zero was used.
The maximum MTU is set by subtracting from tx_max_frame_size to allow
space for headers and frame checksums. As ndev->max_mtu is unsigned,
this subtraction wraps around leading to a ridiculously large positive
value that is obviously incorrect.
Before tx_max_frame_size was introduced, the maximum MTU was based on
rx_max_frame_size. So, we can restore the correct maximum MTU by copying
the rx_max_frame_size value into tx_max_frame_size for RZ/V2M.
Fixes: 1d63864299 ("net: ravb: Fix maximum TX frame size for GbEth devices")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://patch.msgid.link/20250109113706.1409149-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0aa6a37a3 ]
Recalculate features when XDP is detached.
Before:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: off [requested on]
After:
# ip li set dev eth0 xdp obj xdp_dummy.bpf.o sec xdp
# ip li set dev eth0 xdp off
# ethtool -k eth0 | grep gro
rx-gro-hw: on
The fact that HW-GRO doesn't get re-enabled automatically is just
a minor annoyance. The real issue is that the features will randomly
come back during another reconfiguration which just happens to invoke
netdev_update_features(). The driver doesn't handle reconfiguring
two things at a time very robustly.
Starting with commit 98ba1d931f ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") we only reconfigure the RSS hash table
if the "effective" number of Rx rings has changed. If HW-GRO is
enabled "effective" number of rings is 2x what user sees.
So if we are in the bad state, with HW-GRO re-enablement "pending"
after XDP off, and we lower the rings by / 2 - the HW-GRO rings
doing 2x and the ethtool -L doing / 2 may cancel each other out,
and the:
if (old_rx_rings != bp->hw_resc.resv_rx_rings &&
condition in __bnxt_reserve_rings() will be false.
The RSS map won't get updated, and we'll crash with:
BUG: kernel NULL pointer dereference, address: 0000000000000168
RIP: 0010:__bnxt_hwrm_vnic_set_rss+0x13a/0x1a0
bnxt_hwrm_vnic_rss_cfg_p5+0x47/0x180
__bnxt_setup_vnic_p5+0x58/0x110
bnxt_init_nic+0xb72/0xf50
__bnxt_open_nic+0x40d/0xab0
bnxt_open_nic+0x2b/0x60
ethtool_set_channels+0x18c/0x1d0
As we try to access a freed ring.
The issue is present since XDP support was added, really, but
prior to commit 98ba1d931f ("bnxt_en: Fix RSS logic in
__bnxt_reserve_rings()") it wasn't causing major issues.
Fixes: 1054aee823 ("bnxt_en: Use NETIF_F_GRO_HW.")
Fixes: 98ba1d931f ("bnxt_en: Fix RSS logic in __bnxt_reserve_rings()")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://patch.msgid.link/20250109043057.2888953-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d120f27d ]
CPSW ALE has 75-bit ALE entries stored across three 32-bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions support
ALE field entries spanning up to two words at the most.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions work as
expected when ALE field spanned across word1 and word2, but fails when
ALE field spanned across word2 and word3.
For example, while reading the ALE field spanned across word2 and word3
(i.e. bits 62 to 64), the word3 data shifted to an incorrect position
due to the index becoming zero while flipping.
The same issue occurred when setting an ALE entry.
This issue has not been seen in practice but will be an issue in the future
if the driver supports accessing ALE fields spanning word2 and word3
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: b685f1a589 ("net: ethernet: ti: cpsw_ale: Fix cpsw_ale_get_field()/cpsw_ale_set_field()")
Signed-off-by: Sudheer Kumar Doredla <s-doredla@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20250108172433.311694-1-s-doredla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2055272e3a ]
The pci_irq_vector() function never returns zero. It returns negative
error codes or a positive non-zero IRQ number. Fix the error checking to
test for negatives.
Fixes: a36e9f5cfe ("rtase: Add support for a pci table in this module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/f2ecc88d-af13-4651-9820-7cc665230019@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
