commit 3708acbd5f upstream.
In commit 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
Fixes: 4284c88fff ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Link: https://lore.kernel.org/r/20241213143301.4158431-10-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33a6938e0c upstream.
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20241213143301.4158431-9-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1390a33b3d ]
On Microchip PolarFire SoC the PCIe Root Port can be behind one of three
general purpose Fabric Interface Controller (FIC) buses that encapsulates
an AXI-S bus. Depending on which FIC(s) the Root Port is connected through
to CPU space, and what address translation is done by that FIC, the Root
Port driver's inbound address translation may vary.
For all current supported designs and all future expected designs, inbound
address translation done by a FIC on PolarFire SoC varies depending on
whether PolarFire SoC is operating in coherent DMA mode or noncoherent DMA
mode.
The setup of the outbound address translation tables in the Root Port
driver only needs to handle these two cases.
Setup the inbound address translation tables to one of two address
translations, depending on whether the Root Port is being used with
coherent DMA or noncoherent DMA.
Link: https://lore.kernel.org/r/20241011140043.1250030-3-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[bhelgaas: adapt for ac7f53b7e7 ("PCI: microchip: Add support for using
either Root Port 1 or 2")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac7f53b7e7 ]
The PCI host controller on PolarFire SoC has multiple Root Port instances,
each with their own bridge and ctrl address spaces. The original binding
has an "apb" register region, and it is expected to be set to the base
address of the Root Complex register space. Some defines in the Linux
driver were used to compute the addresses of the bridge and ctrl address
ranges corresponding to Root Port instance 1. Some customers want to use
Root Port instance 2 however, which requires changing the defines in the
driver, which is clearly not a portable solution.
The binding has been changed from a single register region to a pair,
corresponding to the bridge and ctrl regions respectively, so modify the
driver to read these regions directly from the devicetree rather than
compute them from the base address of the abp region.
To maintain backwards compatibility with the existing binding, the driver
retains code to handle the "abp" reg and computes the base address of the
bridge and ctrl regions using the defines if it is present. reg-names has
always been a required property, so this is safe to do.
Link: https://lore.kernel.org/r/20241107-surrender-brisket-287d563a5de1@spud
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[bhelgaas: Capitalize PCIe spec terms]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 1390a33b3d ("PCI: microchip: Set inbound address translation for coherent or non-coherent mode")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86a016e278 ]
On the i.MX8QM, PCIe link can't be re-established again in
dw_pcie_resume_noirq(), if the LTSSM_EN bit is not cleared
properly in dw_pcie_suspend_noirq().
So, add dw_pcie_stop_link() to dw_pcie_suspend_noirq() to fix
this issue and to align the suspend/resume functions since there
is dw_pcie_start_link() in dw_pcie_resume_noirq() already.
Fixes: 4774faf854 ("PCI: dwc: Implement generic suspend/resume functionality")
Link: https://lore.kernel.org/r/20241210081557.163555-2-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0639013d3 ]
4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in
'global_irq' interrupt") added the Link Up-based enumeration support, but
did not update the ICC/OPP vote once link is up. Before that, the update
happened during probe and the endpoints may or may not be enumerated at
that time, so the ICC/OPP vote was not guaranteed to be accurate.
With Link Up-based enumeration support, the driver can request the accurate
vote based on the PCIe link.
Call qcom_pcie_icc_opp_update() in qcom_pcie_global_irq_thread() after
enumerating the endpoints.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-3-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93d883f890 ]
Ensure the *_enable_ref_clk() function is symmetric by addressing missing
disable parts on some platforms.
Fixes: d0a75c791f ("PCI: imx6: Factor out ref clock disable to match enable")
Link: https://lore.kernel.org/r/20241126075702.4099164-7-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef61c7d8d0 ]
Since the apps_reset is asserted in imx_pcie_assert_core_reset(), it should
be deasserted in imx_pcie_deassert_core_reset().
Fixes: 9b3fe6796d ("PCI: imx6: Add code to support i.MX7D")
Link: https://lore.kernel.org/r/20241126075702.4099164-6-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f068ffdd03 ]
The i.MX7D only has one PCIe controller, so controller_id should always be
0. The previous code is incorrect although yielding the correct result.
Fix by removing "IMX7D" from the switch case branch.
Fixes: 2d8ed461db ("PCI: imx6: Add support for i.MX8MQ")
Link: https://lore.kernel.org/r/20241126075702.4099164-5-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de22e20589 ]
Pass PHY_MODE_PCIE_EP if the PCI controller operates in Endpoint (EP) mode,
and fix the Root Complex (RC) mode being hardcoded using a drvdata mode
check.
Fixes: 8026f2d8e8 ("PCI: imx6: Call common PHY API to set mode, speed, and submode")
Link: https://lore.kernel.org/r/20241119-pci_fixup_addr-v8-6-c4bfa5193288@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d2da5a4c1 ]
The rcar_pcie_parse_outbound_ranges() uses the devm_request_mem_region()
macro to request a needed resource. A string variable that lives on the
stack is then used to store a dynamically computed resource name, which
is then passed on as one of the macro arguments. This can lead to
undefined behavior.
Depending on the current contents of the memory, the manifestations of
errors may vary. One possible output may be as follows:
$ cat /proc/iomem
30000000-37ffffff :
38000000-3fffffff :
Sometimes, garbage may appear after the colon.
In very rare cases, if no NULL-terminator is found in memory, the system
might crash because the string iterator will overrun which can lead to
access of unmapped memory above the stack.
Thus, fix this by replacing outbound_name with the name of the previously
requested resource. With the changes applied, the output will be as
follows:
$ cat /proc/iomem
30000000-37ffffff : memory2
38000000-3fffffff : memory3
Fixes: 2a6d0d63d9 ("PCI: rcar: Add endpoint mode support")
Link: https://lore.kernel.org/r/tencent_DBDCC19D60F361119E76919ADAB25EC13C06@qq.com
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: King Dix <kingdix10@qq.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6168efbeba ]
A PCI controller device, e.g., StarFive, is parent to PCI host bridge
device. We must enable runtime PM of the controller before enabling runtime
PM of the host bridge, which will happen in pci_host_probe(), to avoid this
warning:
pcie-starfive 940000000.pcie: Enabling runtime PM for inactive device with active children
Fix this issue by enabling StarFive controller device's runtime PM before
calling pci_host_probe() in plda_pcie_host_init().
Link: https://lore.kernel.org/r/20241111-runtime_pm-v7-1-9c164eefcd87@quicinc.com
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d660410631 ]
The remapped PCIe Root Port and the child device have PM L1 Substates
capability, but they are disabled originally.
Here is a failed example on ASUS B1400CEAE:
Capabilities: [900 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1- L1_PM_Substates+
PortCommonModeRestoreTime=32us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2+ ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=101376ns
L1SubCtl2: T_PwrOn=50us
Enable PCI-PM L1 PM Substates for devices below VMD while they are in D0
(see PCIe r6.0, sec 5.5.4).
Link: https://lore.kernel.org/r/20241001083438.10070-4-jhp@endlessos.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218394
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b727484cac ]
Add support for this VMD device which supports the bus restriction mode.
The feature that turns off vector 0 for MSI-X remapping is also enabled.
Link: https://lore.kernel.org/r/20241011175657.249948-1-nirmal.patel@linux.intel.com
Signed-off-by: Nirmal Patel <nirmal.patel@linux.ntel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a63b74f2e3 ]
Add the new IPQ9574 platform which is based on the Qcom IP rev. 1.27.0
and Synopsys IP rev. 5.80a.
The platform itself has four PCIe Gen3 controllers: two single-lane and
two dual-lane, all are based on Synopsys IP rev. 5.70a. As such, reuse
all the members of 'ops_2_9_0'.
Link: https://lore.kernel.org/r/20240801054803.3015572-5-quic_srichara@quicinc.com
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 64f093c4d9 upstream.
The Rockchip PCIe endpoint controller handles PCIe transfers addresses
by masking the lower bits of the programmed PCI address and using the
same number of lower bits masked from the CPU address space used for the
mapping. For a PCI mapping of <size> bytes starting from <pci_addr>,
the number of bits masked is the number of address bits changing in the
address range [pci_addr..pci_addr + size - 1].
However, rockchip_pcie_prog_ep_ob_atu() calculates num_pass_bits only
using the size of the mapping, resulting in an incorrect number of mask
bits depending on the value of the PCI address to map.
Fix this by introducing the helper function
rockchip_pcie_ep_ob_atu_num_bits() to correctly calculate the number of
mask bits to use to program the address translation unit. The number of
mask bits is calculated depending on both the PCI address and size of
the mapping, and clamped between 8 and 20 using the macros
ROCKCHIP_PCIE_AT_MIN_NUM_BITS and ROCKCHIP_PCIE_AT_MAX_NUM_BITS. As
defined in the Rockchip RK3399 TRM V1.3 Part2, Sections 17.5.5.1.1 and
17.6.8.2.1, this clamping is necessary because:
1) The lower 8 bits of the PCI address to be mapped by the outbound
region are ignored. So a minimum of 8 address bits are needed and
imply that the PCI address must be aligned to 256.
2) The outbound memory regions are 1MB in size. So while we can specify
up to 63-bits for the PCI address (num_bits filed uses bits 0 to 5 of
the outbound address region 0 register), we must limit the number of
valid address bits to 20 to match the memory window maximum size (1
<< 20 = 1MB).
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/r/20241017015849.190271-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 118397c9ba upstream.
The advertised resizable BAR size was fixed in commit 72e34b8593 ("PCI:
dwc: endpoint: Fix advertised resizable BAR size").
Commit 867ab111b2 ("PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown()
API to handle Link Down event") was included shortly after this, and
moved the code to another function. When the code was moved, this fix
was mistakenly lost.
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
So, set bit 4 in PCI_REBAR_CAP, so that we actually advertise support
for a 1 MB BAR size.
Fixes: 867ab111b2 ("PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event")
Link: https://lore.kernel.org/r/20241116005950.2480427-2-cassel@kernel.org
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-3-4395534520dc@linaro.org
Link: https://lore.kernel.org/r/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e9ec8d869 upstream.
K2G forwards the error triggered by a link-down state (e.g., no connected
endpoint device) on the system bus for PCI configuration transactions;
these errors are reported as an SError at system level, which is fatal and
hangs the system.
So, apply fix similar to how it was done in the DesignWare Core driver
commit 15b2390634 ("PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()").
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Link: https://lore.kernel.org/r/20240524105714.191642-3-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a938ed948 upstream.
commit 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x
Platforms") introduced configuring "enum dw_pcie_device_mode" as part of
device data ("struct ks_pcie_of_data"). However it failed to set the
mode for "ti,keystone-pcie" compatible.
Since the mode defaults to "DW_PCIE_UNKNOWN_TYPE", the following error
message is displayed for the v3.65a controller:
"INVALID device type 0"
Despite the driver probing successfully, the controller may not be
functional in the Root Complex mode of operation.
So, set the mode as Root Complex for "ti,keystone-pcie" compatible to
fix this.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Link: https://lore.kernel.org/r/20240524105714.191642-2-s-vadapalli@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a726f542d upstream.
The suspend/resume functionality is currently broken on the i.MX6QDL
platform, as documented in the NXP errata (ERR005723):
https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
This patch addresses the issue by sharing most of the suspend/resume
sequences used by other i.MX devices, while avoiding modifications to
critical registers that disrupt the PCIe functionality. It targets the
same problem as the following downstream commit:
4e92355e1f
Unlike the downstream commit, this patch also resets the connected PCIe
device if possible. Without this reset, certain drivers, such as ath10k
or iwlwifi, will crash on resume. The device reset is also done by the
driver on other i.MX platforms, making this patch consistent with
existing practices.
Upon resuming, the kernel will hang and display an error. Here's an
example of the error encountered with the ath10k driver:
ath10k_pci 0000:01:00.0: Unable to change power state from D3hot to D0, device inaccessible
Unhandled fault: imprecise external abort (0x1406) at 0x0106f944
Without this patch, suspend/resume will fail on i.MX6QDL devices if a
PCIe device is connected.
Link: https://lore.kernel.org/r/20241030103250.83640-1-eichest@gmail.com
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
[kwilczynski: commit log, added tag for stable releases]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fba6045161 upstream.
Currently, the cfg_1_9_0 which is being used for X1E80100 doesn't disable
ASPM L0s. However, hardware team recommends to disable L0s as the PHY init
sequence is not tuned support L0s. Hence reuse cfg_sc8280xp for X1E80100.
Note that the config_sid() callback is not present in cfg_sc8280xp, don't
concern about this because config_sid() callback is originally a no-op
for X1E80100.
Fixes: 6d0c39324c ("PCI: qcom: Add X1E80100 PCIe support")
Link: https://lore.kernel.org/r/20241101030902.579789-5-quic_qianyu@quicinc.com
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 6.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 22a9120479 ]
According to Section 2.2 of the PCI Express Card Electromechanical
Specification (Revision 5.1), in order to ensure that the power and the
reference clock are stable, PERST# has to be deasserted after a delay of
100 milliseconds (TPVPERL).
Currently, it is being assumed that the power is already stable, which
is not necessarily true.
Hence, change the delay to PCIE_T_PVPERL_MS to guarantee that power and
reference clock are stable.
Fixes: f3e25911a4 ("PCI: j721e: Add TI J721E PCIe driver")
Fixes: f96b697137 ("PCI: j721e: Use T_PERST_CLK_US macro")
Link: https://lore.kernel.org/r/20241104074420.1862932-1-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40e2125381 ]
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of pex_ep_event_pex_rst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the tegra194 endpoint SoCs supported as of now depend on the refclk
from the host for keeping the controller operational. Due to this
limitation, any access to the hardware registers in the absence of refclk
will result in a whole endpoint crash. Unfortunately, most of the
controller cleanups require accessing the hardware registers (like eDMA
cleanup performed in dw_pcie_ep_cleanup(), etc...). So these cleanup
functions can cause the crash in the endpoint SoC once host asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host.
Thus, fix this crash by moving the controller cleanups to the start of
the pex_ep_event_pex_rst_deassert() function. This function is called
whenever the host has deasserted PERST# and it is guaranteed that the
refclk would be active at this point. So at the start of this function
(after enabling resources) the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-2-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d7cf89b11 ]
Currently, the endpoint cleanup function dw_pcie_ep_cleanup() and EPF
deinit notify function pci_epc_deinit_notify() are called during the
execution of qcom_pcie_perst_assert() i.e., when the host has asserted
PERST#. But quickly after this step, refclk will also be disabled by the
host.
All of the Qcom endpoint SoCs supported as of now depend on the refclk from
the host for keeping the controller operational. Due to this limitation,
any access to the hardware registers in the absence of refclk will result
in a whole endpoint crash. Unfortunately, most of the controller cleanups
require accessing the hardware registers (like eDMA cleanup performed in
dw_pcie_ep_cleanup(), powering down MHI EPF etc...). So these cleanup
functions are currently causing the crash in the endpoint SoC once host
asserts PERST#.
One way to address this issue is by generating the refclk in the endpoint
itself and not depending on the host. But that is not always possible as
some of the endpoint designs do require the endpoint to consume refclk from
the host (as I was told by the Qcom engineers).
Thus, fix this crash by moving the controller cleanups to the start of
the qcom_pcie_perst_deassert() function. qcom_pcie_perst_deassert() is
called whenever the host has deasserted PERST# and it is guaranteed that
the refclk would be active at this point. So at the start of this function
(after enabling resources), the controller cleanup can be performed. Once
finished, rest of the code execution for PERST# deassert can continue as
usual.
Fixes: 473b2cf9c4 ("PCI: endpoint: Introduce 'epc_deinit' event and notify the EPF drivers")
Fixes: 570d7715ee ("PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#")
Link: https://lore.kernel.org/r/20240817-pci-qcom-ep-cleanup-v1-1-d6b958226559@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4a2e2317 ]
Currently, if 'Global IRQ' is supported by the platform, only the Link up
interrupt is enabled in the PARF_INT_ALL_MASK register. This masks MSIs
on some platforms. The MSI bits in PARF_INT_ALL_MASK register are enabled
by default in the hardware, but commit 4581403f67 ("PCI: qcom: Enumerate
endpoints based on Link up event in 'global_irq' interrupt") disabled them
and enabled only the Link up interrupt. While MSI continued to work on the
SM8450 platform that was used to test the offending commit, on other
platforms like SM8250, X1E80100, MSIs are getting masked. And they require
enabling the MSI interrupt bits in the register to unmask (enable) the
MSIs.
Even though the MSI interrupt enable bits in PARF_INT_ALL_MASK are
described as 'diagnostic' interrupts in the internal documentation,
disabling them masks MSI on these platforms. Due to this, MSIs were not
reported to be received these platforms while supporting 'Global IRQ'.
So, enable the MSI interrupts along with the Link up interrupt in the
PARF_INT_ALL_MASK register if 'Global IRQ' is supported. This ensures that
the MSIs continue to work and also the driver is able to catch the Link
up interrupt for enumerating endpoint devices.
Fixes: 4581403f67 ("PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt")
Closes: https://lore.kernel.org/linux-pci/9a692c98-eb0a-4d86-b642-ea655981ff53@kernel.org/
Link: https://lore.kernel.org/r/20241007051255.4378-1-manivannan.sadhasivam@linaro.org
Reported-by: Konrad Dybcio <konradybcio@kernel.org>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SL7
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
-----BEGIN PGP SIGNATURE-----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=L3s9
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
- Fix off-by-one error in INTx IRQ handler that caused INTx interrupts to
be lost or delivered as the wrong interrupt (Sean Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT binding
and xilinx-dma-pl driver (Thippeswamy Havalige)
* pci/controller/xilinx:
PCI: xilinx-xdma: Add Xilinx QDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx QDMA PCIe Root Port Bridge
arm64: zynqmp: Add PCIe phys property for ZCU102
PCI: xilinx-nwl: Add PHY support
dt-bindings: pci: xilinx-nwl: Add phys property
PCI: xilinx-nwl: Clean up clock on probe failure/removal
PCI: xilinx-nwl: Rate-limit misc interrupt messages
PCI: xilinx-nwl: Fix register misspelling
PCI: xilinx-nwl: Fix off-by-one in INTx IRQ handler
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
- Add DT "ti,syscon-acspcie-proxy-ctrl" and driver support to enable the
ACSPCIE module to drive Refclk for the Endpoint (Siddharth Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link setup
can be done separately during resume (Thomas Richard)
- Use dev_err_probe() to simplify j721e probe (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between Refclk
becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
* pci/controller/j721e:
PCI: j721e: Add suspend and resume support
PCI: j721e: Use T_PERST_CLK_US macro
PCI: Add T_PERST_CLK_US macro
PCI: j721e: Add reset GPIO to struct j721e_pcie
PCI: j721e: Use dev_err_probe() in the probe() function
PCI: cadence: Set cdns_pcie_host_init() global
PCI: cadence: Extract link setup sequence from cdns_pcie_host_setup()
PCI: j721e: Enable ACSPCIE Refclk if "ti,syscon-acspcie-proxy-ctrl" exists
dt-bindings: PCI: ti,j721e-pci-host: Add ACSPCIE proxy control property
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP Endpoints
to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which is
harmless for devices that implement their own internal PHY management and
don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver Root
Complex support (Richard Zhu)
* pci/controller/imx6:
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: imx6: Call common PHY API to set mode, speed, and submode
dt-bindings: PCI: imx6q-pcie: Add i.MX8Q PCIe compatible string
PCI: imx6: Consolidate redundant if-checks
PCI: imx6: Improve comment for workaround ERR010728
PCI: imx6: Simplify switch-case logic by involve core_reset callback
PCI: imx6: Introduce SoC specific callbacks for controlling REFCLK
PCI: imx6: Rename imx6_* with imx_*
PCI: imx6: Fix missing call to phy_power_off() in error handling
PCI: imx6: Fix i.MX8MP PCIe EP's occasional failure to trigger MSI
PCI: imx6: Fix establish link failure in EP mode for i.MX8MM and i.MX8MP
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary handler
is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe (Siddharth
Vadapalli)
* pci/controller/dra7xx:
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
- Change DT binding maintainer to Jim Quinlan (Jim Quinlan)
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Refactor .probe() error handling (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add SoC-specific HARD_DEBUG, INTR2_CPU_BASE register offsets (Jim
Quinlan)
- Drop unused RGR1_SW_INIT_1_INIT_MASK, RGR1_SW_INIT_1_INIT_SHIFT offsets
(Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller doesn't
imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Check return values of all reset_control_*() calls (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
* pci/controller/brcmstb:
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
PCI: brcmstb: Enable 7712 SoCs
PCI: brcmstb: Change field name from 'type' to 'soc_base'
PCI: brcmstb: Check return value of all reset_control_* calls
PCI: brcmstb: Refactor for chips with many regular inbound windows
PCI: brcmstb: Don't conflate the reset rescal with PHY ctrl
PCI: brcmstb: Remove two unused constants from driver
PCI: brcmstb: PCI: brcmstb: Make HARD_DEBUG, INTR2_CPU_BASE offsets SoC-specific
PCI: brcmstb: Use swinit reset if available
PCI: brcmstb: Use bridge reset if available
PCI: brcmstb: Use common error handling code in brcm_pcie_probe()
dt-bindings: PCI: brcm,stb-pcie: Add 7712 SoC description
dt-bindings: PCI: brcm,stb-pcie: Use maxItems for reset controllers
dt-bindings: PCI: brcm,stb-pcie: Change brcmstb maintainer and cleanup
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same thing
and is what other drivers use (Jinjie Ruan)
* pci/controller/altera:
PCI: altera: Replace TLP_REQ_ID() with macro PCI_DEVID()
Commit d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq()
call to the bottom of probe") moved the IRQ request for
"dra7xx-pcie-main" towards the end of dra7xx_pcie_probe().
However, the error handling does not take into account the
initialization performed by either dra7xx_add_pcie_port() or
dra7xx_add_pcie_ep(), depending on the mode of operation.
Fix the error handling to address this.
Fixes: d4c7d1a089 ("PCI: dwc: dra7xx: Push request_irq() call to the bottom of probe")
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-3-s-vadapalli@ti.com
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Commit da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for
"dra7xx-pcie-main" IRQ") switched from devm_request_irq() to
devm_request_threaded_irq() for the "dra7xx-pcie-main" interrupt.
Since the primary handler was set to NULL, the "IRQF_ONESHOT" flag
should have also been set. Fix this.
Fixes: da87d35a6e ("PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ")
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/linux-pci/20240827122422.985547-2-s-vadapalli@ti.com
Reported-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently, the dw_pcie::max_link_speed has a valid value only if the
controller driver restricts the maximum link speed in the driver or if
the platform does so in the devicetree using the 'max-link-speed'
property.
But having the maximum supported link speed of the platform would be
helpful for the vendor drivers to configure any link specific settings.
So in the case of non-valid value in dw_pcie::max_link_speed, just cache
the hardware default value from Link Capability register.
While at it, remove the 'max_link_speed' argument to the
dw_pcie_link_set_max_speed() function since the value can be
retrieved within the function.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-2-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
qcom_pcie_enable_resources() is called by qcom_pcie_ep_probe() and it
enables the controller resources like clocks, regulator, PHY. On one of the
new unreleased Qcom SoC, PHY enablement depends on the active refclk. And
on all of the supported Qcom endpoint SoCs, refclk comes from the host
(RC). So calling qcom_pcie_enable_resources() without refclk causes the
NoC (Network On Chip) error in the endpoint SoC and in turn results in a
whole SoC crash and rebooting into EDL (Emergency Download) mode which is
an unrecoverable state.
But qcom_pcie_enable_resources() is already called by
qcom_pcie_perst_deassert() when PERST# is deasserted, and refclk is
available at that time.
Hence, remove the unnecessary call to qcom_pcie_enable_resources() from
qcom_pcie_ep_probe() to prevent the above mentioned crash.
It should be noted that this commit prevents the crash only under normal
working condition (booting endpoint before host), but the crash may also
occur if PERST# assert happens at the wrong time. For avoiding the crash
completely, it is recommended to use SRIS mode which allows the endpoint
SoC to generate its own refclk. The driver is not supporting SRIS mode
currently, but will be added in the future.
Fixes: 869bc52534 ("PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host")
Link: https://lore.kernel.org/linux-pci/20240830082319.51387-1-manivannan.sadhasivam@linaro.org
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
