[ Upstream commit 000cbe3896 ]
This clock can't be enable with VENUS_CORE0 GDSC turned off. But that
GDSC is under HW control so it can be turned off at any moment.
Instead of checking the dependent clock we can just vote for it to
enable later when GDSC gets turned on.
Fixes: 5db3ae8b33 ("clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver")
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20250315-clock-fix-v1-1-2efdc4920dda@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b75c29739 ]
With PWRSTS_OFF_ON, USB GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of USB controller from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Fixes: c58225b7e3 ("clk: qcom: add the SM8650 Global Clock Controller driver, part 1")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250305-topic-sm8650-upstream-fix-usb-suspend-v1-1-649036ab0557@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0079e77c08 ]
The bit index of the peripheral clock for mmc A is wrong
This was probably not a problem for mmc A as the peripheral is likely left
enabled by the bootloader.
No issues has been reported so far but it could be a problem, most likely
some form of conflict between the ethernet and mmc A clock, breaking
ethernet on init.
Use the value provided by the documentation for mmc A before this
becomes an actual problem.
Fixes: 085a4ea93d ("clk: meson: g12a: add peripheral clock controller")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241213-amlogic-clk-g12a-mmca-fix-v1-1-5af421f58b64@baylibre.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91be7d2709 ]
The DSP and OCRAM_A modules from AUDIOMIX are clocked by
AUDIO_AXI_CLK_ROOT, not AUDIO_AHB_CLK_ROOT. Update the clock data
accordingly.
Fixes: 6cd95f7b15 ("clk: imx: imx8mp: Add audiomix block control")
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20250226164513.33822-3-laurentiumihalcea111@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7915d7d540 ]
The 32k clock reference a parent 'cts_slow_oscin' with a fixme note saying
that this clock should be provided by AO controller.
The HW probably has this clock but it does not exist at the moment in
any controller implementation. Furthermore, referencing clock by the global
name should be avoided whenever possible.
There is no reason to keep this hack around, at least for now.
Fixes: 14c735c8e3 ("clk: meson-gxbb: Add EE 32K Clock for CEC")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241220-amlogic-clk-gxbb-32k-fixes-v1-2-baca56ecf2db@baylibre.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8995f8f108 ]
Several clocks used by both g12a and g12b use the g12a cpu A clock hw
pointer as clock parent. This is incorrect on g12b since the parents of
cluster A cpu clock are different. Also the hw clock provided as parent to
these children is not even registered clock on g12b.
Fix the problem by reverting to the global namespace and let CCF pick
the appropriate, as it is already done for other clocks, such as
cpu_clk_trace_div.
Fixes: 25e682a02d ("clk: meson: g12a: migrate to the new parent description method")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241213-amlogic-clk-g12a-cpua-parent-fix-v1-1-d8c0f41865fe@baylibre.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9e60f1ffe ]
Correct the clk_ref_usb3otg parent to fix clock control for the usb3
controller on rk3328. Verified against the rk3328 trm, the rk3228h trm,
and the rk3328 usb3 phy clock map.
Fixes: fe3511ad8a ("clk: rockchip: add clock controller for rk3328")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250115012628.1035928-2-pgwipeout@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b60521eff2 ]
The GPU clock is required for CPU access to GPUSS registers. It was
previously decided (on this and many more platforms) that the added
overhead/hassle introduced by keeping track of it would not bring much
measurable improvement in the power department.
The display clock is basically the same story over again.
Now, we're past that discussion and this commit is not trying to change
that. Instead, the clocks are both force-enabled in .probe *and*
registered with the common clock framework, resulting in them being
toggled off after ignore_unused.
Unregister said clocks to fix breakage when clk_ignore_unused is absent
(as it should be).
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250111-topic-x1e_fixups-v1-1-77dc39237c12@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdc59600bc ]
This clock can't be enable with VENUS_CORE0 GDSC turned off. But that
GDSC is under HW control so it can be turned off at any moment.
Instead of checking the dependent clock we can just vote for it to
enable later when GDSC gets turned on.
Fixes: 9bb6cfc3c7 ("clk: qcom: Add Global Clock Controller driver for MSM8953")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org>
Link: https://lore.kernel.org/r/20250315-clock-fix-v1-2-2efdc4920dda@mainlining.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d7345a7 ]
With UBSAN_ARRAY_BOUNDS=y, I'm hitting the below panic due to
dereferencing `ctx->clk_data.hws` before setting
`ctx->clk_data.num = nr_clks`. Move that up to fix the crash.
UBSAN: array index out of bounds: 00000000f2005512 [#1] PREEMPT SMP
<snip>
Call trace:
samsung_clk_init+0x110/0x124 (P)
samsung_clk_init+0x48/0x124 (L)
samsung_cmu_register_one+0x3c/0xa0
exynos_arm64_register_cmu+0x54/0x64
__gs101_cmu_top_of_clk_init_declare+0x28/0x60
...
Fixes: e620a1e061 ("drivers/clk: convert VL struct to struct_size")
Signed-off-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20250212183253.509771-1-willmcvicker@google.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc0f16c1b7 ]
On the RZ/G3S SoC, the CPU PLL settings can be set and retrieved through
the CPG_PLL1_CLK1 and CPG_PLL1_CLK2 registers. However, these settings
are applied only when CPG_PLL1_SETTING.SEL_PLL1 is set to 0.
Otherwise, the CPU PLL operates at the default frequency of 1.1 GHz.
Hence add support to the PLL driver for returning the 1.1 GHz frequency
when the CPU PLL is configured with the default frequency.
Fixes: 01eabef547 ("clk: renesas: rzg2l: Add support for RZ/G3S PLL")
Fixes: de60a3ebe4 ("clk: renesas: Add minimal boot support for RZ/G3S SoC")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250115142059.1833063-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f38f7fe483 ]
gxbb_32k_clk_div sets CLK_DIVIDER_ROUND_CLOSEST in the init_data flag which
is incorrect. This is field is not where the divider flags belong.
Thankfully, CLK_DIVIDER_ROUND_CLOSEST maps to bit 4 which is an unused
clock flag, so there is no unintended consequence to this error.
Effectively, the clock has been used without CLK_DIVIDER_ROUND_CLOSEST
so far, so just drop it.
Fixes: 14c735c8e3 ("clk: meson-gxbb: Add EE 32K Clock for CEC")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241220-amlogic-clk-gxbb-32k-fixes-v1-1-baca56ecf2db@baylibre.com
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f2052a4a62 upstream.
EARLY_WAKEUP_SW_TRIG_*_SET and EARLY_WAKEUP_SW_TRIG_*_CLEAR
registers are only writeable. Attempting to read these registers
during samsung_clk_save() causes a synchronous external abort.
Remove these 8 registers from cmu_top_clk_regs[] array so that
system suspend gets further.
Note: the code path can be exercised using the following command:
echo mem > /sys/power/state
Fixes: 2c597bb7d6 ("clk: samsung: clk-gs101: Add cmu_top, cmu_misc and cmu_apm support")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250303-clk-suspend-fix-v1-1-c2edaf66260f@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67aea188f2 upstream.
Add dummy clk which was missed during the conversion to
mtk_clk_pdev_probe() and is required for the existing DT bindings to
keep working.
Fixes: 65c10c50c9 ("clk: mediatek: Migrate to mtk_clk_pdev_probe() for multimedia clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/9de23440fcba1ffef9e77d58c9f505105e57a250.1734300668.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 366640868c upstream.
Add dummy clk for index 0 which was missed during the conversion to
mtk_clk_simple_probe().
Fixes: 973d1607d9 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to simplify driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/d677486a5c563fe5c47aa995841adc2aaa183b8a.1734300668.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd291adc5e upstream.
Add dummy clk for index 0 which was missed during the conversion to
mtk_clk_simple_probe().
Fixes: 973d1607d9 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to simplify driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/b8526c882a50f2b158df0eccb4a165956fd8fa13.1734300668.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fba40be5f upstream.
Some of the audio subsystem clocks defined in clk-mt2701.h aren't
actually used by the driver. This broke conversion to
mtk_clk_simple_probe which expects that the highest possible clk id is
defined by the ARRAY_SIZE.
Add additional dummy clocks to fill the gaps and remain compatible with
the existing DT bindings.
Fixes: 0f69a423c4 ("clk: mediatek: Switch to mtk_clk_simple_probe() where possible")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/a07584d803af57b9ce4b5df5e122c09bf5a56ac9.1734300668.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c8746126a upstream.
Commit 973d1607d9 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to
simplify driver") broke DT bindings as the highest index was reduced by
1 because the id count starts from 1 and not from 0.
Fix this, like for other drivers which had the same issue, by adding a
dummy clk at index 0.
Fixes: 973d1607d9 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to simplify driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/b126a5577f3667ef19b1b5feea5e70174084fb03.1734300668.git.daniel@makrotopia.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89aa5925d2 upstream.
aggr_state and unit fields are u32. The result of their
multiplication may not fit in this type.
Add explicit casting to prevent overflow.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 04053f4d23 ("clk: qcom: clk-rpmh: Add IPA clock support")
Cc: stable@vger.kernel.org # 5.4+
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Link: https://lore.kernel.org/r/20241203084231.6001-1-abelova@astralinux.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4cdb196f1 upstream.
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
[ 3.388105] Call trace:
[ 3.390664] qcom_find_src_index+0x3c/0x70 (P)
[ 3.395301] qcom_find_src_index+0x1c/0x70 (L)
[ 3.399934] _freq_tbl_determine_rate+0x48/0x100
[ 3.404753] clk_rcg2_determine_rate+0x1c/0x28
[ 3.409387] clk_core_determine_round_nolock+0x58/0xe4
[ 3.421414] clk_core_round_rate_nolock+0x48/0xfc
[ 3.432974] clk_core_round_rate_nolock+0xd0/0xfc
[ 3.444483] clk_core_set_rate_nolock+0x8c/0x300
[ 3.455886] clk_set_rate+0x38/0x14c
Add the parent_map property for the clock where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
Fixes: 837519775f ("clk: qcom: Add display clock controller driver for SM6350")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241220-sm6350-parent_map-v1-2-64f3d04cb2eb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96fe1a7ee4 upstream.
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
[ 3.388105] Call trace:
[ 3.390664] qcom_find_src_index+0x3c/0x70 (P)
[ 3.395301] qcom_find_src_index+0x1c/0x70 (L)
[ 3.399934] _freq_tbl_determine_rate+0x48/0x100
[ 3.404753] clk_rcg2_determine_rate+0x1c/0x28
[ 3.409387] clk_core_determine_round_nolock+0x58/0xe4
[ 3.421414] clk_core_round_rate_nolock+0x48/0xfc
[ 3.432974] clk_core_round_rate_nolock+0xd0/0xfc
[ 3.444483] clk_core_set_rate_nolock+0x8c/0x300
[ 3.455886] clk_set_rate+0x38/0x14c
Add the parent_map property for two clocks where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
Fixes: 131abae905 ("clk: qcom: Add SM6350 GCC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241220-sm6350-parent_map-v1-1-64f3d04cb2eb@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a57465766a upstream.
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.8
Fixes: c58225b7e3 ("clk: qcom: add the SM8650 Global Clock Controller driver, part 1")
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8650
Link: https://lore.kernel.org/r/20241219170011.70140-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 967e011013 upstream.
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.2
Fixes: 955f2ea3b9 ("clk: qcom: Add GCC driver for SM8550")
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8550
Link: https://lore.kernel.org/r/20241219170011.70140-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f1722eb8 upstream.
Commit c45ae598fc ("clk: qcom: support for alpha mode configuration")
added support for configuring alpha mode, but it seems that the feature
was never working in practice.
The value of the alpha_{en,mode}_mask members of the configuration gets
added to the value parameter passed to the regmap_update_bits() function,
however the same values are not getting applied to the bitmask. As the
result, the respective bits in the USER_CTL register are never modifed
which leads to improper configuration of several PLLs.
The following table shows the PLL configurations where the 'alpha_en_mask'
member is set and which are passed as a parameter for the
clk_alpha_pll_configure() function. In the table the 'expected rate' column
shows the rate the PLL should run at with the given configuration, and
the 'real rate' column shows the rate the PLL runs at actually. The real
rates has been verified on hardwareOn IPQ* platforms, on other platforms,
those are computed values only.
file pll expected rate real rate
dispcc-qcm2290.c disp_cc_pll0 768.0 MHz 768.0 MHz
dispcc-sm6115.c disp_cc_pll0 768.0 MHz 768.0 MHz
gcc-ipq5018.c ubi32_pll 1000.0 MHz != 984.0 MHz
gcc-ipq6018.c nss_crypto_pll 1200.0 MHz 1200.0 MHz
gcc-ipq6018.c ubi32_pll 1497.6 MHz != 1488.0 MHz
gcc-ipq8074.c nss_crypto_pll 1200.0 MHz != 1190.4 MHz
gcc-qcm2290.c gpll11 532.0 MHz != 518.4 MHz
gcc-qcm2290.c gpll8 533.2 MHz != 518.4 MHz
gcc-qcs404.c gpll3 921.6 MHz 921.6 MHz
gcc-sm6115.c gpll11 600.0 MHz != 595.2 MHz
gcc-sm6115.c gpll8 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll0 800.0 MHz != 787.2 MHz
gpucc-sdm660.c gpu_cc_pll1 740.0 MHz != 729.6 MHz
gpucc-sm6115.c gpu_cc_pll0 1200.0 MHz != 1190.4 MHz
gpucc-sm6115.c gpu_cc_pll1 640.0 MHz != 633.6 MHz
gpucc-sm6125.c gpu_pll0 1020.0 MHz != 1017.6 MHz
gpucc-sm6125.c gpu_pll1 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll8 930.0 MHz != 921.6 MHz
mmcc-sdm660.c mmpll5 825.0 MHz != 806.4 MHz
As it can be seen from the above, there are several PLLs which are
configured incorrectly.
Change the code to apply both 'alpha_en_mask' and 'alpha_mode_mask'
values to the bitmask in order to configure the alpha mode correctly.
Applying the 'alpha_en_mask' fixes the initial rate of the PLLs showed
in the table above. Since the 'alpha_mode_mask' is not used by any driver
currently, that part of the change causes no functional changes.
Cc: stable@vger.kernel.org
Fixes: c45ae598fc ("clk: qcom: support for alpha mode configuration")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Gabor Juhos <j4g8y7@gmail.com>
Link: https://lore.kernel.org/r/20241021-fix-alpha-mode-config-v1-1-f32c254e02bc@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fb33b6797 upstream.
Since commit 02fb4f0084 ("clk: clk-loongson2: Fix potential buffer
overflow in flexible-array member access"), the clk provider register is
failed.
The count of `clks_num` is shown below:
for (p = data; p->name; p++)
clks_num++;
In fact, `clks_num` represents the number of SoC clocks and should be
expressed as the maximum value of the clock binding id in use (p->id + 1).
Now we fix it to avoid the following error when trying to register a clk
provider:
[ 13.409595] of_clk_hw_onecell_get: invalid index 17
Cc: stable@vger.kernel.org
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Fixes: 02fb4f0084 ("clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/82e43d89a9a6791129cf8ea14f4eeb666cd87be4.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e24b15d470 upstream.
Setting the genpd's struct device's name with dev_set_name() is
happening within pm_genpd_init(). If it remains NULL, things can blow up
later, such as when crafting the devfs hierarchy for the power domain:
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
...
Call trace:
strlen from start_creating+0x90/0x138
start_creating from debugfs_create_dir+0x20/0x178
debugfs_create_dir from genpd_debug_add.part.0+0x4c/0x144
genpd_debug_add.part.0 from genpd_debug_init+0x74/0x90
genpd_debug_init from do_one_initcall+0x5c/0x244
do_one_initcall from kernel_init_freeable+0x19c/0x1f4
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x28
Bisecting tracks this crash back to commit 899f44531f ("pmdomain: core:
Add GENPD_FLAG_DEV_NAME_FW flag"), which exchanges use of genpd->name
with dev_name(&genpd->dev) in genpd_debug_add.part().
Fixes: 899f44531f ("pmdomain: core: Add GENPD_FLAG_DEV_NAME_FW flag")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable@vger.kernel.org # v6.12+
Link: https://lore.kernel.org/r/20241231190336.423172-1-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1641472004 upstream.
While testing the MMC nodes proposed in [1], it was noted that mmc0/1
would fail to initialize, with "mmc: fatal err update clk timeout" in
the kernel logs. A closer look at the clock definitions showed that the MMC
MPs had the "CLK_SET_RATE_NO_REPARENT" flag set. No reason was given for
adding this flag in the first place, and its original purpose is unknown,
but it doesn't seem to make sense and results in severe limitations to MMC
speeds. Thus, remove this flag from the 3 MMC MPs.
[1] https://msgid.link/20241024170540.2721307-10-masterr3c0rd@epochal.quest
Fixes: fb038ce4db ("clk: sunxi-ng: add support for the Allwinner A100 CCU")
Cc: stable@vger.kernel.org
Signed-off-by: Cody Eksal <masterr3c0rd@epochal.quest>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://patch.msgid.link/20241109003739.3440904-1-masterr3c0rd@epochal.quest
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d26c4ad3fa upstream.
Allowing the usb_2 controller GDSC to be turned off during system suspend
renders the controller unable to resume.
So use PWRSTS_RET_ON instead in order to make sure this the GDSC doesn't
go down.
Fixes: 161b7c401f ("clk: qcom: Add Global Clock controller (GCC) driver for X1E80100")
Cc: stable@vger.kernel.org # 6.8
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250107-x1e80100-clk-gcc-fix-usb2-gdsc-pwrsts-v1-1-e15d1a5e7d80@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7f12857f0 ]
In wrpll_configure_for_rate() we try to determine the best PLL
configuration for a target rate. However, in the loop where we try
values of R, we should compare the derived `vco` with `target_vco_rate`.
However, we were in fact comparing it with `target_rate`, which is
actually after Q shift. This is incorrect, and sometimes can result in
suboptimal clock rates. Fix it.
Fixes: 7b9487a9a5 ("clk: analogbits: add Wide-Range PLL library")
Signed-off-by: Bo Gan <ganboing@gmail.com>
Link: https://lore.kernel.org/r/20240830061639.2316-1-ganboing@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a43cd19f1 ]
cpu2vp_clk is a gate but was mistakenly in th1520_div_clks[] instead
of th1520_gate_clks[].
Fixes: ae81b69fd2 ("clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks")
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Link: https://lore.kernel.org/r/20241228034802.1573554-1-dfustini@tenstorrent.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 037705e94b ]
Add the CLK_IGNORE_UNUSED flag to apb_pclk, cpu2peri_x2h_clk,
perisys_apb2_hclk and perisys_apb3_hclk.
Without this flag, the boot hangs after "clk: Disabling unused clocks"
unless clk_ignore_unused is in the kernel cmdline.
Fixes: ae81b69fd2 ("clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks")
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Link: https://lore.kernel.org/r/20250113-th1520-clk_ignore_unused-v1-2-0b08fb813438@tenstorrent.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a826e53fd7 ]
Modify the call to devm_clk_hw_register_gate_parent_data() to actually
pass the clk flags from hw.init instead of just 0. This is necessary to
allow individual clk gates to specify their own clk flags.
Fixes: ae81b69fd2 ("clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks")
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
Link: https://lore.kernel.org/r/20250113-th1520-clk_ignore_unused-v1-1-0b08fb813438@tenstorrent.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830d8062d2 ]
Ralink SoC RT3883 has already 'xtal' defined as a base clock so there is no
need to redefine it again in fixed clocks section. Hence, remove the duplicate
one from there.
Fixes: d34db686a3 ("clk: ralink: mtmips: fix clocks probe order in oldest ralink SoCs")
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20250108093636.265033-1-sergio.paracuellos@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f760a4bb5e ]
Similar to the earlier fixes meant for sm8x50 and x1e platforms,
we have to stop using the shared clk ops for sdm845 QUPs as well.
As Stephen Boyd pointed out in earlier fixes, there wasn't a problem
to mark QUP clks shared until we started parking shared RCGs at clk
registration time in commit 01a0a6cc8c ("clk: qcom: Park shared RCGs
upon registration"). Parking at init is actually harmful to the UART
when earlycon is used. If the device is pumping out data while the
frequency changes and we see garbage on the serial console until the
driver can probe and actually set a proper frequency.
This patch reverts the QUP clk sharing ops part of commit 06391eddb6
("clk: qcom: Add Global Clock controller (GCC) driver for SDM845"), so
that the QUPs on sdm845 don't get parked during clk registration and
break UART operations.
Fixes: 01a0a6cc8c ("clk: qcom: Park shared RCGs upon registration")
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Link: https://lore.kernel.org/r/20241209174912.2526928-1-amit.pundir@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 383ca7bee8 ]
Stop force-selecting PLL-MIPI as TCON0 parent, since it breaks video
output on Pinebook that uses RGB to eDP bridge.
Partially revert commit ca1170b699 ("clk: sunxi-ng: a64: force
select PLL_MIPI in TCON0 mux"), while still leaving
CLK_SET_RATE_NO_REPARENT flag set, since we do not want the clock to
be reparented.
The issue is that apparently different TCON0 outputs require a different
clock, or the mux might be selecting the output type.
I did an experiment: I manually configured PLL_MIPI and PLL_VIDEO0_2X
to the same clock rate and flipped the switch with devmem. Experiment
clearly showed that whenever PLL_MIPI is selected as TCON0 clock parent,
the video output stops working.
Therefore, TCON0 clock parent corresponding to the output type must be
assigned in the device tree.
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on PinePhone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patch.msgid.link/20250104074035.1611136-5-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f368cb7ef ]
Drop redundant CLK_PLL_VIDEO0_2X and CLK_PLL.MIPI. These are now
defined in dt-bindings/clock/sun50i-a64-ccu.h
Fixes: ca1170b699 ("clk: sunxi-ng: a64: force select PLL_MIPI in TCON0 mux")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Frank Oltmanns <frank@oltmanns.dev> # on pinephone
Tested-by: Stuart Gathman <stuart@gathman.org> # on OG pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Link: https://patch.msgid.link/20250104074035.1611136-3-anarsoul@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9377941f2 ]
The Titan TOP GDSC is the parent GDSC for all other GDSCs in the CAMCC
block. None of the subordinate blocks will switch on without the parent
GDSC switched on.
Fixes: 76126a5129 ("clk: qcom: Add camcc clock driver for x1e80100")
Acked-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20241227-b4-linux-next-24-12-16-titan-top-gdsc-v1-1-c96ef62fc307@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48806be086 ]
Enable the LVDS gate, MIPI DSI, PXP, FLEXIO and MU only for i.MX93,
because i.MX91 does not support them.
Update enet clk entry format to align with others.
Fixes: a27bfff88d ("clk: imx: add i.MX91 clk")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241225001443.883131-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a78535444 ]
Split IMX93_CLK_SPDIF_IPG from IMX93_CLK_SPDIF_GATE
because the IMX93_CLK_SPDIF_GATE controls the gate
of IPG clock and root clock. Without this change,
disabling IMX93_CLK_SPDIF_GATE would also disable
the IPG clock, causing register access failures.
Fixes: 1c4a4f7362 ("arm64: dts: imx93: Add audio device nodes")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241119015805.3840606-3-shengjiu.wang@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a27bfff88d ]
Reuse i.MX93 clk driver for i.MX91, because i.MX91 reuses the
Clock Control Module from i.MX93, with only a few clocks removed
and a few clocks added.
For clocks specific to i.MX93 use PLAT_IMX93 to flag them, for
clocks specific to i.MX91, use PLAT_IMX91 to flag them. Others
are shared by both.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241023184651.381265-5-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Stable-dep-of: 6a78535444 ("clk: imx93: Add IMX93_CLK_SPDIF_IPG clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0af18ba607 ]
IMX93_CLK_END was previously defined in imx93-clock.h to indicate
the number of clocks. However, it is not part of the ABI. For starters
it does no really appear in DTS. But what's more important - new clocks
are described later, which contradicts this define in binding header.
So move this macro to clock driver.
Signed-off-by: Pengfei Li <pengfei.li_1@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241023184651.381265-2-pengfei.li_1@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Stable-dep-of: 6a78535444 ("clk: imx93: Add IMX93_CLK_SPDIF_IPG clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9b7c84d22 ]
The CLKOUTn may be fed from PLL1/2/3, but the PLL1/2/3 has to be enabled
first by setting PLL_CLKE bit 11 in CCM_ANALOG_SYS_PLLn_GEN_CTRL register.
The CCM_ANALOG_SYS_PLLn_GEN_CTRL bit 11 is modeled by plln_out clock. Fix
the clock tree and place the clkout1/2 under plln_sel instead of plain plln
to let the clock subsystem correctly control the bit 11 and enable the PLL
in case the CLKOUTn is supplied by PLL1/2/3.
Fixes: 43896f56b5 ("clk: imx8mp: add clkout1/2 support")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20241112013718.333771-1-marex@denx.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28fa3291ca ]
Current implementation of of_clk_get_parent_name() leaks an OF node
reference on error path. Add a of_node_put() call before returning an
error.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 8da411cc19 ("clk: let of_clk_get_parent_name() fail for invalid clock-indices")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://lore.kernel.org/r/20241210130913.3615205-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6ca7e6240 ]
A device_node reference obtained via of_find_node_by_path() requires
explicit calls to of_node_put() after it is no longer required to avoid
leaking the resource.
Instead of adding the missing calls to of_node_put() in all execution
paths, use the cleanup attribute for 'soc' by means of the __free()
macro, which automatically calls of_node_put() when the variable goes
out of scope.
Fixes: 6aa1754764 ("clk: renesas: cpg-mssr: Ignore all clocks assigned to non-Linux system")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20241031-clk-renesas-cpg-mssr-cleanup-v2-1-0010936d1154@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c384481006 upstream.
clk_imx8mp_audiomix_reset_controller_register() in the
"if !CONFIG_RESET_CONTROLLER" branch had the first
argument missing. It is an empty function for this branch
so it wasn't immediately apparent.
Fixes: 6f0e817175 ("clk: imx: clk-audiomix: Add reset controller")
Cc: <stable@vger.kernel.org> # 6.12.x
Signed-off-by: Nikolaus Voss <nv@vosn.de>
Link: https://lore.kernel.org/r/20241219105447.889CB11FE@mail.steuer-voss.de
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4bf0b909a ]
In accordance with LicheePi 4A BSP the clock that comes to emmc/sdhci
is 198Mhz which is got through frequency division of source clock
VIDEO PLL by 4 [1].
But now the AP_SUBSYS driver sets the CLK EMMC SDIO to the same
frequency as the VIDEO PLL, equal to 792 MHz. This causes emmc/sdhci
to work 4 times slower.
Let's fix this issue by adding fixed factor clock that divides
VIDEO PLL by 4 for emmc/sdhci.
Link: 7563179071/drivers/clk/thead/clk-light-fm.c (L454)
Fixes: ae81b69fd2 ("clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks")
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20241210083029.92620-1-bigunclemax@gmail.com
Tested-by: Xi Ruoyao <xry111@xry111.site>
Reviewed-by: Drew Fustini <dfustini@tenstorrent.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2eb75f86d5 upstream.
The Documentation for EN7581 had a typo and still referenced the EN7523
BUS base source frequency. This was in conflict with a different page in
the Documentration that state that the BUS runs at 300MHz (600MHz source
with divisor set to 2) and the actual watchdog that tick at half the BUS
clock (150MHz). This was verified with the watchdog by timing the
seconds that the system takes to reboot (due too watchdog) and by
operating on different values of the BUS divisor.
The correct values for source of BUS clock are 600MHz and 540MHz.
This was also confirmed by Airoha.
Cc: stable@vger.kernel.org
Fixes: 66bc47326c ("clk: en7523: Add EN7581 support")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20241116105710.19748-1-ansuelsmth@gmail.com
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
