commit b8665a1b49 upstream.
In 2020, there's been an unnoticed change which rightfully attempted to
report probe deferrals upon DMA absence by checking the return value of
dma_request_chan_by_mask(). By doing so, it also reported errors which
were simply ignored otherwise, likely on purpose.
This change actually turned a void return into an error code. Hence, not
only the -EPROBE_DEFER error codes but all error codes got reported to
the callers, now failing to probe in the absence of Rx DMA channel,
despite the fact that DMA seems to not be supported natively by many
implementations.
Looking at the history, this change probably led to:
ad2775dc3f ("spi: cadence-quadspi: Disable the DAC for Intel LGM SoC")
f724c296f2 ("spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA")
In my case, the AM62A LP SK core octo-SPI node from TI does not
advertise any DMA channel, hinting that there is likely no support for
it, but yet when the support for the am654 compatible was added, DMA
seemed to be used, so just discarding its use with the
CQSPI_DISABLE_DAC_MODE quirk for this compatible does not seem the
correct approach.
Let's get change the return condition back to:
- return a probe deferral error if we get one
- ignore the return value otherwise
The "error" log level was however likely too high for something that is
expected to fail, so let's lower it arbitrarily to the info level.
Fixes: 935da5e510 ("mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting DMA channel")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250305200933.2512925-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e19c1272c8 ]
The lookup table forces the use of the "pinctrl-bcm2835" GPIO chip
provider and essentially assumes that there is going to be such a
provider, and if not, we will fail to set-up the SPI device.
While this is true on Raspberry Pi based systems (2835/36/37, 2711,
2712), this is not true on 7712/77122 Broadcom STB systems which use the
SPI driver, but not the GPIO driver.
There used to be an early check:
chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
if (!chip)
return 0;
which would accomplish that nicely, bring something similar back by
checking for the compatible strings matched by the pinctrl-bcm2835.c
driver, if there is no Device Tree node matching those compatible
strings, then we won't find any GPIO provider registered by the
"pinctrl-bcm2835" driver.
Fixes: 21f252cd29 ("spi: bcm2835: reduce the abuse of the GPIO API")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250401233603.2938955-1-florian.fainelli@broadcom.com
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d669101052 ]
If we are unable to lookup the chip-select GPIO, the error path will
call bcm2835_spi_cleanup() which unconditionally calls gpiod_put() on
the cs->gpio variable which we just determined was invalid.
Fixes: 21f252cd29 ("spi: bcm2835: reduce the abuse of the GPIO API")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250401224238.2854256-1-florian.fainelli@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91cf42c63f upstream.
When the size of a transfer exceeds the size of the FIFO (32 bytes), RX
overflows will be generated and receive data will be corrupted and
warnings will be produced. For example, here's an error generated by a
transfer of 36 bytes:
spi_master spi0: mchp_corespi_interrupt: RX OVERFLOW: rxlen: 4, txlen: 0
The driver is currently split between handling receiving in the
interrupt handler, and sending outside of it. Move all handling out of
the interrupt handling, and explicitly link the number of bytes read of
of the RX FIFO to the number written into the TX one. This both resolves
the overflow problems as well as simplifying the flow of the driver.
CC: stable@vger.kernel.org
Fixes: 9ac8d17694 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250303-veal-snooper-712c1dfad336@wendy
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3588b1c0fd ]
When there is no dummy cycle in the spi-nor commands, both dummy bus cycle
bytes and width are zero. Because of the cpu's warning when divided by
zero, the warning should be avoided. Return just zero to avoid such
calculations.
Fixes: 1b74dd64c8 ("spi: Add Socionext F_OSPI SPI flash controller driver")
Co-developed-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kohei Ito <ito.kohei@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://patch.msgid.link/20250206085747.3834148-1-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit be92ab2de0 upstream.
The QSPI peripheral control and status registers are
accessible via the SoC's APB bus, whereas MMIO transactions'
data travels on the AHB bus.
Microchip documentation and even sample code from Atmel
emphasises the need for a memory barrier before the first
MMIO transaction to the AHB-connected QSPI, and before the
last write to its registers via APB. This is achieved by
the following lines in `atmel_qspi_transfer()`:
/* Dummy read of QSPI_IFR to synchronize APB and AHB accesses */
(void)atmel_qspi_read(aq, QSPI_IFR);
However, the current documentation makes no mention to
synchronization requirements in the other direction, i.e.
after the last data written via AHB, and before the first
register access on APB.
In our case, we were facing an issue where the QSPI peripheral
would cease to send any new CSR (nCS Rise) interrupts,
leading to a timeout in `atmel_qspi_wait_for_completion()`
and ultimately this panic in higher levels:
ubi0 error: ubi_io_write: error -110 while writing 63108 bytes
to PEB 491:128, written 63104 bytes
After months of extensive research of the codebase, fiddling
around the debugger with kgdb, and back-and-forth with
Microchip, we came to the conclusion that the issue is
probably that the peripheral is still busy receiving on AHB
when the LASTXFER bit is written to its Control Register
on APB, therefore this write gets lost, and the peripheral
still thinks there is more data to come in the MMIO transfer.
This was first formulated when we noticed that doubling the
write() of QSPI_CR_LASTXFER seemed to solve the problem.
Ultimately, the solution is to introduce memory barriers
after the AHB-mapped MMIO transfers, to ensure ordering.
Fixes: d5433def31 ("mtd: spi-nor: atmel-quadspi: Add spi-mem support to atmel-quadspi")
Cc: Hari.PrasathGE@microchip.com
Cc: Mahesh.Abotula@microchip.com
Cc: Marco.Cardellini@microchip.com
Cc: stable@vger.kernel.org # c0a0203cf5: ("spi: atmel-quadspi: Create `atmel_qspi_ops`"...)
Cc: stable@vger.kernel.org # 6.x.y
Signed-off-by: Bence Csókás <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241219091258.395187-1-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a0203cf5 upstream.
Refactor the code to introduce an ops struct, to prepare for merging
support for later SoCs, such as SAMA7G5. This code was based on the
vendor's kernel (linux4microchip). Cc'ing original contributors.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241128174316.3209354-2-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a07eb4f67e ]
devm_clk_get_optional() returns NULL for missing clocks and a PTR_ERR()
if there is a clock but we fail to get it, but currently we only handle
the latter case and do so as though the clock was missing. If we get an
error back we should handle that as an error since the clock exists but
we failed to get it, if we get NULL then the clock doesn't exist and we
should handle that.
Fixes: 4c6ac5446d ("spi: omap2-mcspi: Fix the IS_ERR() bug for devm_clk_get_optional_enabled()")
Reported-by: Lars Pedersen <lapeddk@gmail.com>
Link: https://patch.msgid.link/20250117-spi-fix-omap2-optional-v1-1-e77d4ac6db6e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lars Pedersen <lapeddk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8332e66709 ]
Add check for the return value of clk_enable() to catch the potential
error.
Fixes: c618a90dca ("spi: zynq-qspi: Drop GPIO header")
Signed-off-by: Mingwei Zheng <zmw12306@gmail.com>
Signed-off-by: Jiasheng Jiang <jiashengjiangcool@gmail.com>
Link: https://patch.msgid.link/20241207015206.3689364-1-zmw12306@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25fb0e77b9 ]
STIG mode is enabled by default for less than 8 bytes data read/write.
STIG mode doesn't work with Altera SocFPGA platform due hardware
limitation.
Add a quirks to disable STIG mode for Altera SoCFPGA platform.
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Link: https://patch.msgid.link/20241204063338.296959-1-niravkumar.l.rabara@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c6ac5446d ]
The devm_clk_get_optional_enabled() function returns error
pointers(PTR_ERR()). So use IS_ERR() to check it.
Verified on K3-J7200 EVM board, without clock node mentioned
in the device tree.
Signed-off-by: Purushothama Siddaiah <psiddaiah@mvista.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://patch.msgid.link/20241205070426.1861048-1-psiddaiah@mvista.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb259e43b ]
The Panther Lake SPI controllers are compatible with the Cannon Lake
controllers. Add support for following SPI controller device IDs:
- H-series: 0xe323
- P-series: 0xe423
- U-series: 0xe423
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20241204080208.1036537-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0bb394067a upstream.
The early bail out that caused an out-of-bounds write was removed with
commit 5c018e378f ("spi: spi-rockchip: Fix out of bounds array
access")
Unfortunately that caused the PM runtime count to be unbalanced and
underflowed on the first call. To fix that reintroduce a no-op check
by reading the register directly.
Cc: stable@vger.kernel.org
Fixes: 5c018e378f ("spi: spi-rockchip: Fix out of bounds array access")
Signed-off-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/1f2b3af4-2b7a-4ac8-ab95-c80120ebf44c@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa8ecda987 ]
The target value of scldiv is just a byte, but its calculation in
fsl_lpspi_set_bitrate could be negative. So use an adequate type to store
the result and avoid overflows. After that this needs range check
adjustments, but this should make the code less opaque.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240930093056.93418-2-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 984836621a ]
If we remove the module which will call mpc52xx_spi_remove
it will free 'ms' through spi_unregister_controller.
while the work ms->work will be used. The sequence of operations
that may lead to a UAF bug.
Fix it by ensuring that the work is canceled before proceeding with
the cleanup in mpc52xx_spi_remove.
Fixes: ca632f5566 ("spi: reorganize drivers")
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/1f16f8ae0e50ca9adb1dc849bf2ac65a40c9ceb9.1732783000.git.xiaopei01@kylinos.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d24cfee7f6 upstream.
When probing spi device take care of deferred probe of ACPI irq gpio
similar like for OF/DT case.
>From practical standpoint this fixes issue with vsc-tp driver on
Dell XP 9340 laptop, which try to request interrupt with spi->irq
equal to -EPROBE_DEFER and fail to probe with the following error:
vsc-tp spi-INTC10D0:00: probe with driver vsc-tp failed with error -22
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 33ada67da3 ("ACPI / spi: attach GPIO IRQ from ACPI description to SPI device")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com> # Dell XPS9320, ov01a10
Link: https://patch.msgid.link/20241122094224.226773-1-stanislaw.gruszka@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ac40e6d0c ]
`atmel_qspi_reg_name()` is used for pretty-printing register offsets
for verbose logging of register accesses. However, due to a typo
(likely a copy-paste error), QSPI_RD's offset prints as "MR", the
name of the previous register. Fix this typo.
Fixes: c528ecfbef ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Link: https://patch.msgid.link/20241122141302.2599636-1-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2219576883 ]
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time.
So, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 9e3a000362 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240920091135.2741574-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f399051ec1 ]
A shift-out-of-bounds issue was identified by UBSAN in the
tegra_qspi_fill_tx_fifo_from_client_txbuf() function.
UBSAN: shift-out-of-bounds in drivers/spi/spi-tegra210-quad.c:345:27
shift exponent 32 is too large for 32-bit type 'u32' (aka 'unsigned int')
Call trace:
tegra_qspi_start_cpu_based_transfer
The problem arises when shifting the contents of tx_buf left by 8 times
the value of i, which can exceed 4 and result in an exponent larger than
32 bits.
Resolve this by restrict the value of i to be less than 4, preventing
the shift operation from overflowing.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 921fc1838f ("spi: tegra210-quad: Add support for Tegra210 QSPI controller")
Link: https://patch.msgid.link/20241004125400.1791089-1-leitao@debian.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 003c7e0191 ]
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable when request IRQ.
Fixes: 9728fb3ce1 ("spi: lpspi: disable lpspi module irq in DMA mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906022828.891812-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The op argument is missing the colon and is not picked up by the
kerneldoc generator. Fix it to address the following build warning:
drivers/spi/spi-mtk-snfi.c:1201: warning: Function parameter or struct member 'op' not described in 'mtk_snand_is_page_ops'
Fixes: 764f1b7481 ("spi: add driver for MTK SPI NAND Flash Interface")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20241021142113.71081-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The STM32MP25 SOC has capability to behave in device mode however
missing .has_device_mode within its stm32mp25_spi_cfg structure leads
to not being able to enable the device mode.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patch.msgid.link/20241009-spi-mp25-device-fix-v1-1-8e5ca7db7838@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A small set of driver specific fixes that came in since the merge
window, about half of which is fixes for correctness in the use of the
runtime PM APIs done as part of a broader cleanup.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmcAZPQACgkQJNaLcl1U
h9AcWgf9Hj53LZPeQgf/fDgr6ZEqpxR4v+ZStlHSlm4gbIHs84Wtj+mPMYFJ1hVK
0fL34wKKTd8ckhp4Ys/8mNyMRrZegmQET8kEWoeM+gqAlzLQkDuJ5kQEaZlKYeRb
Q2aiQfLxvvKVoxdJNOq8SZHlU9in1X4y8sZ1okfYY2lFS//pi3+P8IGFlN/K7vTs
hxucI5gNsithiVQ1nCzLP6BawwZcICo/zTpiBt4Xiuj7GohrWsWFq9fqwx6Jj6xh
nkvHdpuC743qrcUoKjnXVr3PCKjDK+pSp84O7aDgrlC2HZuXyDvhRKAw5NtL0HwH
2opB09eItz1bn4KRCf6MrY6/7VV5Rw==
=Mjs1
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small set of driver specific fixes that came in since the merge
window, about half of which is fixes for correctness in the use of the
runtime PM APIs done as part of a broader cleanup"
* tag 'spi-fix-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: s3c64xx: fix timeout counters in flush_fifo
spi: atmel-quadspi: Fix wrong register value written to MR
spi: spi-cadence: Fix missing spi_controller_is_target() check
spi: spi-cadence: Fix pm_runtime_set_suspended() with runtime pm enabled
spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
In the s3c64xx_flush_fifo() code, the loops counter is post-decremented
in the do { } while(test && loops--) condition. This means the loops is
left at the unsigned equivalent of -1 if the loop times out. The test
after will never pass as if tests for loops == 0.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Fixes: 230d42d422 ("spi: Add s3c64xx SPI Controller driver")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://patch.msgid.link/20240924134009.116247-2-ben.dooks@codethink.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_controller_is_target() check is missing for pm_runtime_disable()
in cdns_spi_remove(), add it.
Fixes: b1b90514ea ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-4-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: d36ccd9f7e ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 43b6bf406c ("spi: imx: fix runtime pm support for !CONFIG_PM")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
no_llseek had been defined to NULL two years ago, in commit 868941b144
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----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=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
Some driver specific fixes that came in during the merge window. Lorenzo
Bianconi did some extra testing on the recently added arioha driver and
found some issues, Alexander Dahl fixed some issues with signal delays
in the Atmel QSPI driver and Jinjie Ruan has been fixing some nits with
runtime PM cleanup.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmbz0NIACgkQJNaLcl1U
h9B1KQf/fcq8ApnJCgD9EykeE9ekziI6PRwxc3XqI+DCws7CN2n4EbIsJxCeiygl
d4vWcnBssQGxVv6IbSl3Vgqr6PSAxBxibpBgmANR0HJ8YLFjxoaDTk9ufnJevOEm
pMgAtzvt3Ral1VwspKsz3puXEVoJaIoELfEQRB7D8XCX26ypD7+sZSN/AjMATp/N
zla5mPjQfGIX7dOis1kaRCQ0ysxoEdZ9zsyFlGs+VZkFIhHbu3KTLhlfADruOa7k
RKuVABAIJwqPz6Gew82xlh4hQPP+aecWNdwCSK6+4FZkZLgvUz2rx7evVj3U5+xd
Hc3jQmoGnVMYqeuK4BC8T0frnlp6eA==
=iJa9
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.12-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Some driver specific fixes that came in during the merge window.
Lorenzo Bianconi did some extra testing on the recently added arioha
driver and found some issues, Alexander Dahl fixed some issues with
signal delays in the Atmel QSPI driver and Jinjie Ruan has been fixing
some nits with runtime PM cleanup"
* tag 'spi-fix-v6.12-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel-quadspi: Avoid overwriting delay register settings
spi: airoha: remove read cache in airoha_snand_dirmap_read()
spi: spi-fsl-lpspi: Undo runtime PM changes at driver exit time
spi: atmel-quadspi: Undo runtime PM changes at driver exit time
spi: airoha: fix airoha_snand_{write,read}_data data_len estimation
spi: airoha: fix dirmap_{read,write} operations
Previously the MR and SCR registers were just set with the supposedly
required values, from cached register values (cached reg content
initialized to zero).
All parts fixed here did not consider the current register (cache)
content, which would make future support of cs_setup, cs_hold, and
cs_inactive impossible.
Setting SCBR in atmel_qspi_setup() erases a possible DLYBS setting from
atmel_qspi_set_cs_timing(). The DLYBS setting is applied by ORing over
the current setting, without resetting the bits first. All writes to MR
did not consider possible settings of DLYCS and DLYBCT.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Fixes: f732646d0c ("spi: atmel-quadspi: Add support for configuring CS timing")
Link: https://patch.msgid.link/20240918082744.379610-2-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 4a2f83b7f7 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906023956.1004440-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix data length written and read in airoha_snand_write_data and
airoha_snand_read_data routines respectively if it is bigger than
SPI_MAX_TRANSFER_SIZE.
Fixes: a403997c12 ("spi: airoha: add SPI-NAND Flash controller driver")
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240913-airoha-spi-fixes-v1-2-de2e74ed4664@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI_NFI_READ_FROM_CACHE_DONE bit must be written at the end of
dirmap_read operation even if it is already set.
In the same way, SPI_NFI_LOAD_TO_CACHE_DONE bit must be written at the
end of dirmap_write operation even if it is already set.
For this reason use regmap_write_bits() instead of regmap_set_bits().
This patch fixes mtd_pagetest kernel module test.
Fixes: a403997c12 ("spi: airoha: add SPI-NAND Flash controller driver")
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240913-airoha-spi-fixes-v1-1-de2e74ed4664@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a quiet release for sPI. The one new core feature here is
support for configuring the state of the MOSI pin when the bus is idle,
there are some devices which are very fragile in this regard even when
the chip select signal is not asserted. Otherwise we have some new
driver support, a bunch of small fixes and some general cleanup work.
- Support for configuring the state of the MOSI pin when the the bus is
idle.
- Add the Elgin JG0309-01 in spidev.
- Support for Marvell xSPI, Mediatek MTK7981, Microchip PIC64GX,
NXP i.MX8ULP, and Rockchip RK3576 controllers.
I also accidentally pulled in an IIO DT bindings update due to a typo
when applying the MOSI idle state patches.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmbnaTcACgkQJNaLcl1U
h9BsXwf/bqArB1QiWT1t34WMKcowO6r0eCjRNSrpqcsOIprUa/0OYxXqsPJzigKV
g9HF0w2uh15NByTv+KulH4r0QPa9JOeFHFx31+bec8PFdJoUwcNjWNUi7EaQgOLp
/XzdahLhPhiBIraCts2JdRD8+4C9JlU0VeRdDRFMjl5+SB8Fjqx6mQ/rw68fEZGG
YvUTIVNT2h00W6aMKmKN0rni5ny2qNIDm6sVj/dWSWbQCPcYjVG3kxI2dmlKIm3S
ccKp4JHoOYpu9egp+t134bi/iLfOwP+vsmqWPqoI7J1cx78E9gH3QBf02KmTDbux
m/02FtCFDh5hyXke9yn/QIZvO2bKzA==
=UtQA
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release for SPI. The one new core feature here
is support for configuring the state of the MOSI pin when the bus is
idle, there are some devices which are very fragile in this regard
even when the chip select signal is not asserted. Otherwise we have
some new driver support, a bunch of small fixes and some general
cleanup work.
- Support for configuring the state of the MOSI pin when the the bus
is idle
- Add the Elgin JG0309-01 in spidev
- Support for Marvell xSPI, Mediatek MTK7981, Microchip PIC64GX, NXP
i.MX8ULP, and Rockchip RK3576 controllers
I also accidentally pulled in an IIO DT bindings update due to a typo
when applying the MOSI idle state patches"
* tag 'spi-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (65 commits)
spi: geni-qcom: Use devm functions to simplify code
spi: remove spi_controller_is_slave() and spi_slave_abort()
platform/olpc: olpc-xo175-ec: switch to use spi_target_abort().
spi: slave-mt27xx: switch to use target_abort
spi: spidev: switch to use spi_target_abort()
spi: slave-system-control: switch to use spi_target_abort()
spi: slave-time: switch to use spi_target_abort()
spi: switch to use spi_controller_is_target()
spi: fspi: add support for imx8ulp
spi: fspi: involve lut_num for struct nxp_fspi_devtype_data
dt-bindings: spi: nxp-fspi: add imx8ulp support
spi: spidev_fdx: Fix the wrong format specifier
spi: mxs: Switch to RUNTIME/SYSTEM_SLEEP_PM_OPS()
spi: dt-bindings: Add rockchip,rk3576-spi compatible
spi: Revert "spi: Insert the missing pci_dev_put()before return"
spi: zynq-qspi: Replace kzalloc with kmalloc for buffer allocation
spi: ppc4xx: Sort headers
spi: ppc4xx: Revert "handle irq_of_parse_and_map() errors"
spi: zynqmp-gqspi: Simplify with dev_err_probe()
spi: zynqmp-gqspi: Use devm_spi_alloc_host()
...
Two fields got removed but are still documented:
drivers/spi/spi-ep93xx.c:98: warning: Excess struct member 'dma_rx_data' description in 'ep93xx_spi'
drivers/spi/spi-ep93xx.c:98: warning: Excess struct member 'dma_tx_data' description in 'ep93xx_spi'
Fixes: 3cfe73256905 ("spi: ep93xx: add DT support for Cirrus EP93xx")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add OF ID match table
- add device tree DMA request, so we can probe defer, in case DMA is not
ready yet
- drop DMA platform code
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use devm_pm_runtime_enable(), devm_request_irq() and
devm_spi_register_controller() to simplify code.
And also register a callback spi_geni_release_dma_chan() with
devm_add_action_or_reset(), to release dma channel in both error
and device detach path, which can make sure the release sequence is
consistent with the original one.
1. Unregister spi controller.
2. Free the IRQ.
3. Free DMA chans
4. Disable runtime PM.
So the remove function can also be removed.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240912091701.3720857-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the memcpy length to fix the out-of-bounds issue when writing the
data that is not 4 byte aligned to TX FIFO.
To reproduce the issue, write 3 bytes data to NOR chip.
dd if=3b of=/dev/mtd0
[ 36.926103] ==================================================================
[ 36.933409] BUG: KASAN: slab-out-of-bounds in nxp_fspi_exec_op+0x26ec/0x2838
[ 36.940514] Read of size 4 at addr ffff00081037c2a0 by task dd/455
[ 36.946721]
[ 36.948235] CPU: 3 UID: 0 PID: 455 Comm: dd Not tainted 6.11.0-rc5-gc7b0e37c8434 #1070
[ 36.956185] Hardware name: Freescale i.MX8QM MEK (DT)
[ 36.961260] Call trace:
[ 36.963723] dump_backtrace+0x90/0xe8
[ 36.967414] show_stack+0x18/0x24
[ 36.970749] dump_stack_lvl+0x78/0x90
[ 36.974451] print_report+0x114/0x5cc
[ 36.978151] kasan_report+0xa4/0xf0
[ 36.981670] __asan_report_load_n_noabort+0x1c/0x28
[ 36.986587] nxp_fspi_exec_op+0x26ec/0x2838
[ 36.990800] spi_mem_exec_op+0x8ec/0xd30
[ 36.994762] spi_mem_no_dirmap_read+0x190/0x1e0
[ 36.999323] spi_mem_dirmap_write+0x238/0x32c
[ 37.003710] spi_nor_write_data+0x220/0x374
[ 37.007932] spi_nor_write+0x110/0x2e8
[ 37.011711] mtd_write_oob_std+0x154/0x1f0
[ 37.015838] mtd_write_oob+0x104/0x1d0
[ 37.019617] mtd_write+0xb8/0x12c
[ 37.022953] mtdchar_write+0x224/0x47c
[ 37.026732] vfs_write+0x1e4/0x8c8
[ 37.030163] ksys_write+0xec/0x1d0
[ 37.033586] __arm64_sys_write+0x6c/0x9c
[ 37.037539] invoke_syscall+0x6c/0x258
[ 37.041327] el0_svc_common.constprop.0+0x160/0x22c
[ 37.046244] do_el0_svc+0x44/0x5c
[ 37.049589] el0_svc+0x38/0x78
[ 37.052681] el0t_64_sync_handler+0x13c/0x158
[ 37.057077] el0t_64_sync+0x190/0x194
[ 37.060775]
[ 37.062274] Allocated by task 455:
[ 37.065701] kasan_save_stack+0x2c/0x54
[ 37.069570] kasan_save_track+0x20/0x3c
[ 37.073438] kasan_save_alloc_info+0x40/0x54
[ 37.077736] __kasan_kmalloc+0xa0/0xb8
[ 37.081515] __kmalloc_noprof+0x158/0x2f8
[ 37.085563] mtd_kmalloc_up_to+0x120/0x154
[ 37.089690] mtdchar_write+0x130/0x47c
[ 37.093469] vfs_write+0x1e4/0x8c8
[ 37.096901] ksys_write+0xec/0x1d0
[ 37.100332] __arm64_sys_write+0x6c/0x9c
[ 37.104287] invoke_syscall+0x6c/0x258
[ 37.108064] el0_svc_common.constprop.0+0x160/0x22c
[ 37.112972] do_el0_svc+0x44/0x5c
[ 37.116319] el0_svc+0x38/0x78
[ 37.119401] el0t_64_sync_handler+0x13c/0x158
[ 37.123788] el0t_64_sync+0x190/0x194
[ 37.127474]
[ 37.128977] The buggy address belongs to the object at ffff00081037c2a0
[ 37.128977] which belongs to the cache kmalloc-8 of size 8
[ 37.141177] The buggy address is located 0 bytes inside of
[ 37.141177] allocated 3-byte region [ffff00081037c2a0, ffff00081037c2a3)
[ 37.153465]
[ 37.154971] The buggy address belongs to the physical page:
[ 37.160559] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x89037c
[ 37.168596] flags: 0xbfffe0000000000(node=0|zone=2|lastcpupid=0x1ffff)
[ 37.175149] page_type: 0xfdffffff(slab)
[ 37.179021] raw: 0bfffe0000000000 ffff000800002500 dead000000000122 0000000000000000
[ 37.186788] raw: 0000000000000000 0000000080800080 00000001fdffffff 0000000000000000
[ 37.194553] page dumped because: kasan: bad access detected
[ 37.200144]
[ 37.201647] Memory state around the buggy address:
[ 37.206460] ffff00081037c180: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
[ 37.213701] ffff00081037c200: fa fc fc fc 05 fc fc fc 03 fc fc fc 02 fc fc fc
[ 37.220946] >ffff00081037c280: 06 fc fc fc 03 fc fc fc fc fc fc fc fc fc fc fc
[ 37.228186] ^
[ 37.232473] ffff00081037c300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.239718] ffff00081037c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.246962] ==================================================================
[ 37.254394] Disabling lock debugging due to kernel taint
0+1 records in
0+1 records out
3 bytes copied, 0.335911 s, 0.0 kB/s
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Cc: stable@kernel.org
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://patch.msgid.link/20240911211146.3337068-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
