[ Upstream commit cd4c002506 ]
GPIO_OUT[0] is connected to the reset pin of embedded UFS device.
Before powering off the phy assert the reset signal.
This is added as a gs101 specific suspend hook so as not to have any
unintended consequences for other SoCs supported by this driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-7-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67e4085015 ]
ufshcd_pltfrm_remove() calls ufshcd_remove(hba) which in turn calls
ufshcd_hba_exit().
By moving the phy_power_off() and phy_exit() calls to the newly created
.exit callback they get called by ufshcd_variant_hba_exit() before
ufshcd_hba_exit() turns off the regulators. This is also similar flow to
the ufs-qcom driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-6-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deac9ad496 ]
PRDT_PREFETCH_ENABLE[31] bit should be set when desctype field of
fmpsecurity0 register is type2 (double file encryption) or type3
(support for file and disk encryption). Setting this bit enables PRDT
pre-fetching on both TXPRDT and RXPRDT.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-5-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d101165e7 ]
Ensure clocks are enabled before configuring unipro. Additionally move
the pre_link() hook before the exynos_ufs_phy_init() calls. This means
the register write sequence more closely resembles the ordering of the
downstream driver.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-1-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f92bb74368 ]
If dma-coherent property isn't set then descriptors are non-cacheable
and the iocc shareability bits should be disabled. Without this UFS can
end up in an incompatible configuration and suffer from random cache
related stability issues.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Fixes: cc52e15397 ("scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-3-96722cc2ba1b@linaro.org
Cc: Chanho Park <chanho61.park@samsung.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f5ef7eeb ]
gs101 I/O coherency shareability bits differ from exynosauto SoC. To
support both SoCs move this info the SoC drvdata.
Currently both the value and mask are the same for both gs101 and
exynosauto, thus we use the same value.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-2-96722cc2ba1b@linaro.org
Fixes: d11e0a318d ("scsi: ufs: exynos: Add support for Tensor gs101 SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc4a4a576 ]
Factor out the common code into a new exynos_ufs_shareability() function
and provide a dedicated gs101_drv_init() hook.
This allows us to enable WriteBooster capability (UFSHCD_CAP_WB_EN) in a
way that doesn't effect other SoCs supported in this driver.
WriteBooster improves write speeds by enabling a pseudo SLC cache. Using
the 'fio seqwrite' test we can achieve speeds of 945MB/s with this
feature enabled (until the cache is exhausted) before dropping back to
~260MB/s (which are the speeds we see without the WriteBooster feature
enabled).
Assuming the UFSHCD_CAP_WB_EN capability is set by the host then
WriteBooster can also be enabled and disabled via sysfs so it is
possible for the system to only enable it when extra write performance
is required.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-10-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd613ca2c ]
The pointer to device can be obtained from ufs->hba->dev, remove
superfluous function parameter.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-3-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07c2a73750 ]
Remove empty method. When the method is not set, the call is not made,
saving a few cycles.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-2-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded40f32b5 ]
The driver leaks the device reference taken with
of_find_device_by_node(). Fix the leak by using devm_of_qcom_ice_get().
Fixes: 56541c7c44 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # SCSI
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250117-qcom-ice-fix-dev-leak-v2-3-1ffa5b6884cb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7f05fd9a3b upstream.
ufshcd_link_startup() can call ufshcd_vops_link_startup_notify()
multiple times when retrying. This causes the phy reference count to
keep increasing and the phy to not properly re-initialize.
If the phy has already been previously powered on, first issue a
phy_power_off() and phy_exit(), before re-initializing and powering on
again.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-4-96722cc2ba1b@linaro.org
Fixes: 3d73b200f9 ("scsi: ufs: ufs-exynos: Change ufs phy control sequence")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8fb2403dd upstream.
devm_blk_crypto_profile_init() registers a cleanup handler to run when
the associated (platform-) device is being released. For UFS, the
crypto private data and pointers are stored as part of the ufs_hba's
data structure 'struct ufs_hba::crypto_profile'. This structure is
allocated as part of the underlying ufshcd and therefore Scsi_host
allocation.
During driver release or during error handling in ufshcd_pltfrm_init(),
this structure is released as part of ufshcd_dealloc_host() before the
(platform-) device associated with the crypto call above is released.
Once this device is released, the crypto cleanup code will run, using
the just-released 'struct ufs_hba::crypto_profile'. This causes a
use-after-free situation:
Call trace:
kfree+0x60/0x2d8 (P)
kvfree+0x44/0x60
blk_crypto_profile_destroy_callback+0x28/0x70
devm_action_release+0x1c/0x30
release_nodes+0x6c/0x108
devres_release_all+0x98/0x100
device_unbind_cleanup+0x20/0x70
really_probe+0x218/0x2d0
In other words, the initialisation code flow is:
platform-device probe
ufshcd_pltfrm_init()
ufshcd_alloc_host()
scsi_host_alloc()
allocation of struct ufs_hba
creation of scsi-host devices
devm_blk_crypto_profile_init()
devm registration of cleanup handler using platform-device
and during error handling of ufshcd_pltfrm_init() or during driver
removal:
ufshcd_dealloc_host()
scsi_host_put()
put_device(scsi-host)
release of struct ufs_hba
put_device(platform-device)
crypto cleanup handler
To fix this use-after free, change ufshcd_alloc_host() to register a
devres action to automatically cleanup the underlying SCSI device on
ufshcd destruction, without requiring explicit calls to
ufshcd_dealloc_host(). This way:
* the crypto profile and all other ufs_hba-owned resources are
destroyed before SCSI (as they've been registered after)
* a memleak is plugged in tc-dwc-g210-pci.c remove() as a
side-effect
* EXPORT_SYMBOL_GPL(ufshcd_dealloc_host) can be removed fully as
it's not needed anymore
* no future drivers using ufshcd_alloc_host() could ever forget
adding the cleanup
Fixes: cb77cb5abe ("blk-crypto: rename blk_keyslot_manager to blk_crypto_profile")
Fixes: d76d9d7d10 ("scsi: ufs: use devm_blk_ksm_init()")
Cc: stable@vger.kernel.org
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20250124-ufshcd-fix-v4-1-c5d0144aae59@linaro.org
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a0905caf5 upstream.
Commit 56541c7c44 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
introduced an incorrect check of the algorithm ID into the key eviction
path, and thus qcom_ice_evict_key() is no longer ever called. Fix it.
Fixes: 56541c7c44 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20241210030839.1118805-1-ebiggers@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bac656875 upstream.
PHY might already be powered on during ufs_qcom_power_up_sequence() in a
couple of cases:
1. During UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH quirk
2. Resuming from spm_lvl = 5 suspend
In those cases, it is necessary to call phy_power_off() and phy_exit() in
ufs_qcom_power_up_sequence() function to power off the PHY before calling
phy_init() and phy_power_on().
Case (1) is doing it via ufs_qcom_reinit_notify() callback, but case (2) is
not handled. So to satisfy both cases, call phy_power_off() and phy_exit()
if the phy_count is non-zero. And with this change, the reinit_notify()
callback is no longer needed.
This fixes the below UFS resume failure with spm_lvl = 5:
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufs_device_wlun 0:0:0:49488: ufshcd_wl_resume failed: -5
ufs_device_wlun 0:0:0:49488: PM: dpm_run_callback(): scsi_bus_resume returns -5
ufs_device_wlun 0:0:0:49488: PM: failed to resume async: error -5
Cc: stable@vger.kernel.org # 6.3
Fixes: baf5ddac90 ("scsi: ufs: ufs-qcom: Add support for reinitializing the UFS device")
Reported-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # on SM8550-HDK
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241219-ufs-qcom-suspend-fix-v3-1-63c4b95a70b9@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 897df60c16 ]
This will ensure that the scsi host is cleaned up properly using
scsi_host_dev_release(). Otherwise, it may lead to memory leaks.
Cc: stable@vger.kernel.org # 4.4
Fixes: 03b1781aa9 ("[SCSI] ufs: Add Platform glue driver for ufshcd")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-5-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78bc671bd1 ]
Replace UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS with
ufs_hba_variant_ops::set_dma_mask. Update the Renesas driver
accordingly. This patch enables supporting other configurations than
32-bit or 64-bit DMA addresses, e.g. 36-bit DMA addresses.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241018194753.775074-1-bvanassche@acm.org
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1745dcdb72 upstream.
During the remove stage of glue drivers, some of them are incrementing the
reference count using pm_runtime_get_sync(), before removing the ufshcd
using ufshcd_remove(). But they are not dropping that reference count after
ufshcd_remove() to balance the refcount.
So drop the reference count by calling pm_runtime_put_noidle() after
ufshcd_remove(). Since the behavior is applicable to all glue drivers, move
the PM handling to ufshcd_pltfrm_remove().
Cc: stable@vger.kernel.org # 3.12
Fixes: 62694735ca ("[SCSI] ufs: Add runtime PM support for UFS host controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-4-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3326e6a3f upstream.
When the UFSHCD platform glue drivers are removed, runtime PM should be
disabled using pm_runtime_disable() to balance the enablement done in
ufshcd_pltfrm_init(). This is also reported by PM core when the glue driver
is removed and inserted again:
ufshcd-qcom 1d84000.ufshc: Unbalanced pm_runtime_enable!
So disable runtime PM using a new helper API ufshcd_pltfrm_remove(), that
also takes care of removing ufshcd. This helper should be called during the
remove() stage of glue drivers.
Cc: stable@vger.kernel.org # 3.12
Fixes: 62694735ca ("[SCSI] ufs: Add runtime PM support for UFS host controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-3-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c662cedea1 upstream.
Move the EXYNOS_UFS_OPT_UFSPR_SECURE check inside
exynos_ufs_config_smu().
This way all call sites will benefit from the check. This fixes a bug
currently in the exynos_ufs_resume() path on gs101 as it calls
exynos_ufs_config_smu() and we end up accessing registers that can only
be accessed from secure world which results in a serror.
Fixes: d11e0a318d ("scsi: ufs: exynos: Add support for Tensor gs101 SoC")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-5-peter.griffin@linaro.org
Cc: stable@vger.kernel.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
These are mostly minor updates. There are two drivers (lpfc and
mpi3mr) which missed the initial pull and a core change to retry a
start/stop unit which affect suspend/resume.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZvh4QiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishQajAQDx561I
cgbPZjZkSOYp+qJowaphyySZ1SS8pfMlVAIiXQEAs4SqhIN8e9QWpgI0bA7X7xtB
UiOUsIHPHM+BFU6kbJQ=
=qjsp
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"These are mostly minor updates.
There are two drivers (lpfc and mpi3mr) which missed the initial
pull and a core change to retry a start/stop unit which affect
suspend/resume"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi: lpfc: Update lpfc version to 14.4.0.5
scsi: lpfc: Support loopback tests with VMID enabled
scsi: lpfc: Revise TRACE_EVENT log flag severities from KERN_ERR to KERN_WARNING
scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance
scsi: lpfc: Fix kref imbalance on fabric ndlps from dev_loss_tmo handler
scsi: lpfc: Restrict support for 32 byte CDBs to specific HBAs
scsi: lpfc: Update phba link state conditional before sending CMF_SYNC_WQE
scsi: lpfc: Add ELS_RSP cmd to the list of WQEs to flush in lpfc_els_flush_cmd()
scsi: mpi3mr: Update driver version to 8.12.0.0.50
scsi: mpi3mr: Improve wait logic while controller transitions to READY state
scsi: mpi3mr: Update MPI Headers to revision 34
scsi: mpi3mr: Use firmware-provided timestamp update interval
scsi: mpi3mr: Enhance the Enable Controller retry logic
scsi: sd: Fix off-by-one error in sd_read_block_characteristics()
scsi: pm8001: Do not overwrite PCI queue mapping
scsi: scsi_debug: Remove a useless memset()
scsi: pmcraid: Convert comma to semicolon
scsi: sd: Retry START STOP UNIT commands
scsi: mpi3mr: A performance fix
scsi: ufs: qcom: Update MODE_MAX cfg_bw value
...
Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr). There are no user visible core changes and a whole series of
minor updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZuvd5yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishV7dAQC+TSlv
BeNm8W4yAFCXLCwnJh8rT6ZzuBsjsIHH1DPP3wD+IXuIOFf5gVRJGpCNJc/dI082
/ehSrIdeJxwaNoOOt+Y=
=SXZD
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, smartpqi, NCR5380, mac_scsi, lpfc,
mpi3mr).
There are no user visible core changes and a whole series of minor
updates and fixes. The largest core change is probably the
simplification of the workqueue allocation path"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (86 commits)
scsi: smartpqi: update driver version to 2.1.30-031
scsi: smartpqi: fix volume size updates
scsi: smartpqi: fix rare system hang during LUN reset
scsi: smartpqi: add new controller PCI IDs
scsi: smartpqi: add counter for parity write stream requests
scsi: smartpqi: correct stream detection
scsi: smartpqi: Add fw log to kdump
scsi: bnx2fc: Remove some unused fields in struct bnx2fc_rport
scsi: qla2xxx: Remove the unused 'del_list_entry' field in struct fc_port
scsi: ufs: core: Remove ufshcd_urgent_bkops()
scsi: core: Remove obsoleted declaration for scsi_driverbyte_string()
scsi: bnx2i: Remove unused declarations
scsi: core: Simplify an alloc_workqueue() invocation
scsi: ufs: Simplify alloc*_workqueue() invocation
scsi: stex: Simplify an alloc_ordered_workqueue() invocation
scsi: scsi_transport_fc: Simplify alloc_workqueue() invocations
scsi: snic: Simplify alloc_workqueue() invocations
scsi: qedi: Simplify an alloc_workqueue() invocation
scsi: qedf: Simplify alloc_workqueue() invocations
scsi: myrs: Simplify an alloc_ordered_workqueue() invocation
...
Commit 8db8f6ce55 ("scsi: ufs: qcom: Add missing interconnect bandwidth
values for Gear 5") updated the ufs_qcom_bw_table for Gear 5. However, it
missed updating the cfg_bw value for the max mode.
Hence update the cfg_bw value for the max mode for UFS 4.x devices.
Fixes: 8db8f6ce55 ("scsi: ufs: qcom: Add missing interconnect bandwidth values for Gear 5")
Cc: stable@vger.kernel.org
Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
Link: https://lore.kernel.org/r/20240903063709.4335-1-quic_mapa@quicinc.com
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MT8183 implements the UFSHCI 2.1 spec but reports a bogus value of 1 in
the reserved part for the Legacy Single Doorbell Support (LSDBS)
capability.
Set UFSHCD_QUIRK_BROKEN_LSDBS_CAP when MCQ support is explicitly
disabled, allowing the device to be properly registered.
Signed-off-by: Mary Guillemard <mary@mary.zone>
Link: https://lore.kernel.org/r/20240818222442.44990-3-mary@mary.zone
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SM8550 SoC has the UFSHCI 4.0 compliant UFS controller and only supports
legacy single doorbell mode without MCQ. But due to a hardware bug, it
reports 1 in the 'Legacy Queue & Single Doorbell Support (LSDBS)' field of
the Controller Capabilities register. This field is supposed to read as 0
if legacy single doorbell mode is supported and 1 otherwise.
Starting with commit 0c60eb0cc3 ("scsi: ufs: core: Check LSDBS cap when
!mcq"), ufshcd driver is now relying on the LSDBS field to decide when to
use the legacy doorbell mode if MCQ is not supported. And this ends up
breaking UFS on SM8550:
ufshcd-qcom 1d84000.ufs: ufshcd_init: failed to initialize (legacy doorbell mode not supported)
ufshcd-qcom 1d84000.ufs: error -EINVAL: Initialization failed with error -22
So use the UFSHCD_QUIRK_BROKEN_LSDBS_CAP quirk for SM8550 SoC so that the
ufshcd driver could use legacy doorbell mode correctly.
Fixes: 0c60eb0cc3 ("scsi: ufs: core: Check LSDBS cap when !mcq")
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240816-ufs-bug-fix-v3-2-e6fe0e18e2a3@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The "sz" variable needs to be a signed type for the error handling to work
as intended. Fortunately, there is some sanity checking on "sz" on the
next line, so negative values would be caught and it doesn't really affect
runtime.
Fixes: eab0dce11d ("scsi: ufs: ufshcd-pltfrm: Use of_property_count_u32_elems() to get property length")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/404a4727-89c6-410b-9ece-301fa399d4db@stanley.mountain
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace of_get_property() with the type specific
of_property_count_u32_elems() to get the property length.
This is part of a larger effort to remove callers of of_get_property() and
similar functions. of_get_property() leaks the DT property data pointer
which is a problem for dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240808170704.1438658-1-robh@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use of_property_present() to test for property presence rather than
of_find_property(). This is part of a larger effort to remove callers of
of_find_property() and similar functions. of_find_property() leaks the DT
struct property and data pointers which is a problem for dynamically
allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240808170644.1436991-1-robh@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If exynos_ufs_fmp_init() did not enable FMP support, then
exynos_ufs_fmp_resume() should not execute the FMP-related SMC calls.
Fixes: c96499fcb4 ("scsi: ufs: exynos: Add support for Flash Memory Protector (FMP)")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20240721183840.209284-1-ebiggers@kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Eric Biggers <ebiggers@kernel.org> says:
Add support for Flash Memory Protector (FMP), which is the inline
encryption hardware on Exynos and Exynos-based SoCs.
Specifically, add support for the "traditional FMP mode" that works on
many Exynos-based SoCs including gs101. This is the mode that uses
"software keys" and is compatible with the upstream kernel's existing
inline encryption framework in the block and filesystem layers. I
plan to add support for the wrapped key support on gs101 at a later
time.
Tested on gs101 (specifically Pixel 6) by running the 'encrypt' group
of xfstests on a filesystem mounted with the 'inlinecrypt' mount
option.
This patchset applies to v6.10-rc6, and it has no prerequisites that
aren't already upstream.
Link: https://lore.kernel.org/r/20240708235330.103590-1-ebiggers@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for Flash Memory Protector (FMP), which is the inline
encryption hardware on Exynos and Exynos-based SoCs.
Specifically, add support for the "traditional FMP mode" that works on many
Exynos-based SoCs including gs101. This is the mode that uses "software
keys" and is compatible with the upstream kernel's existing inline
encryption framework in the block and filesystem layers. I plan to add
support for the wrapped key support on gs101 at a later time.
Tested on gs101 (specifically Pixel 6) by running the 'encrypt' group of
xfstests on a filesystem mounted with the 'inlinecrypt' mount option.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20240708235330.103590-7-ebiggers@kernel.org
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche <bvanassche@acm.org> says:
Hi Martin,
Please consider this series of UFS driver patches for the next merge window.
Thank you,
Bart.
Link: https://lore.kernel.org/r/20240708211716.2827751-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Improve code readability by inlining is_mcq_enabled().
Cc: Peter Wang <peter.wang@mediatek.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240708211716.2827751-7-bvanassche@acm.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable suspending clk scaling on no request for Qualcomm SoC.
Signed-off-by: Ram Prakash Gupta <quic_rampraka@quicinc.com>
Link: https://lore.kernel.org/r/20240627083756.25340-3-quic_rampraka@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCI ID to support Intel Panther Lake, same as MTL.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240618073158.38504-1-adrian.hunter@intel.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With ARCH=arm64, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/ufs/host/ufs-qcom.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240625-md-drivers-ufs-host-v2-1-59a56974b05a@quicinc.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Recently, ufs-mcq feature has been introduced to QEMU hw/ufs device [1].
This patch adds MCQ support for upstream QEMU UFS PCI controller. This
patch provides mandatory vops callbacks to make UFS controller work
properly on MCQ mode. Operation and Runtime Config register stride is
fixed to 48bytes which is implemented by qemu.
[1] https://lore.kernel.org/qemu-devel/cover.1716876237.git.jeuk20.kim@samsung.com/
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
Link: https://lore.kernel.org/r/20240531212244.1593535-2-minwoo.im@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers. The remaining patches are assorted minor fixes and
deprecated function updates plus a bit of constification.
Signed-off-by: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZkOnWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYe7AP93XRN/
xnccJbSTTUL4FFGobq2CYXv58Na+FM/b/+/kEAD+PNi0LmHDdDTOaFUblMd9l4lj
mpvYLRvJ6ifnHX6WXAg=
=PVnL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"Updates to the usual drivers (ufs, lpfc, qla2xxx, mpi3mr, libsas).
The major update (which causes a conflict with block, see below) is
Christoph removing the queue limits and their associated block
helpers.
The remaining patches are assorted minor fixes and deprecated function
updates plus a bit of constification"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
scsi: mpi3mr: Sanitise num_phys
scsi: lpfc: Copyright updates for 14.4.0.2 patches
scsi: lpfc: Update lpfc version to 14.4.0.2
scsi: lpfc: Add support for 32 byte CDBs
scsi: lpfc: Change lpfc_hba hba_flag member into a bitmask
scsi: lpfc: Introduce rrq_list_lock to protect active_rrq_list
scsi: lpfc: Clear deferred RSCN processing flag when driver is unloading
scsi: lpfc: Update logging of protection type for T10 DIF I/O
scsi: lpfc: Change default logging level for unsolicited CT MIB commands
scsi: target: Remove unused list 'device_list'
scsi: iscsi: Remove unused list 'connlist_err'
scsi: ufs: exynos: Add support for Tensor gs101 SoC
scsi: ufs: exynos: Add some pa_dbg_ register offsets into drvdata
scsi: ufs: exynos: Allow max frequencies up to 267Mhz
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_TIMER_TICK_SELECT option
scsi: ufs: exynos: Add EXYNOS_UFS_OPT_UFSPR_SECURE option
scsi: ufs: dt-bindings: exynos: Add gs101 compatible
scsi: qla2xxx: Fix debugfs output for fw_resource_count
scsi: qedf: Ensure the copied buf is NUL terminated
scsi: bfa: Ensure the copied buf is NUL terminated
...
Peter Griffin <peter.griffin@linaro.org> says:
Hi Martin, James & Alim,
This series adds support to the ufs-exynos driver for Tensor gs101
found in Pixel 6. It was send previously in [1] and [2] but included
the other clock, phy and DTS parts. This series has been split into
just the ufs-exynos part to hopefully make things easier.
With this series, plus the phy, clock and dts changes UFS is
functional upstream for Pixel 6. The SKhynix HN8T05BZGKX015 can be
enumerated, partitions mounted etc.
The series is split into some prepatory patches for ufs-exynos and a
final patch that adds the gs101 support.
Note the sysreg clock has been moved to ufs node as fine grained clock
control around the syscon sysreg register accesses doesn't result in
functional UFS.
regards,
Peter
Link: https://lore.kernel.org/r/20240426122004.2249178-1-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a dedicated compatible and drv_data with associated hooks for gs101 SoC
found on Pixel 6.
Note we make use of the previously added EXYNOS_UFS_OPT_UFSPR_SECURE
option, to skip initialisation of UFSPR registers as these are only
accessible via SMC call.
EXYNOS_UFS_OPT_TIMER_TICK_SELECT option is also set to select tick
source. This has been done so as not to effect any existing platforms.
DBG_OPTION_SUITE on gs101 has different address offsets to other SoCs so
these register offsets now come from uic_attr struct.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-7-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This allows these registers to be at different offsets or not exist at all
on some SoCs variants.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-6-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Platforms such as Tensor gs101 the pclk frequency is 267Mhz. Increase
PCLK_AVAIL_MAX so we don't fail the frequency check.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-5-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This option is intended to be set for SoCs that have HCI_V2P1_CTRL register
and can select their tick source via IA_TICK_SEL bit.
Source clock selection for timer tick
0x0 = Bus clock (aclk)
0x1 = Function clock (mclk)
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-4-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This option is intended to be set on platforms whose ufspr registers are
only accessible via smc call (such as gs101).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240426122004.2249178-3-peter.griffin@linaro.org
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Christoph Hellwig <hch@lst.de> says:
Hi all,
this series converts the SCSI midlayer and LLDDs to use atomic queue
limits API. It is pretty straight forward, except for the mpt3mr
driver which does really weird and probably already broken things by
setting limits from unlocked device iteration callbacks.
I will probably defer the (more complicated) ULD changes to the next
merge window as they would heavily conflict with Damien's zone write
plugging series. With that the series could go in through the SCSI
tree if Jens' ACKs the core block layer bits.
Link: https://lore.kernel.org/r/20240409143748.980206-1-hch@lst.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add MODULE_DEVICE_TABLE() so the module can be properly autoloaded based on
the alias from of_device_id table.
Cc: Will McVicker <willmcvicker@google.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240409203954.80484-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Export the module alias information using the MODULE_DEVICE_TABLE() macro
in order to support auto-loading this module for devices that support it.
$ modinfo -F alias out/linux/drivers/ufs/host/ufs-exynos.ko
of:N*T*Ctesla,fsd-ufsC*
of:N*T*Ctesla,fsd-ufs
of:N*T*Csamsung,exynosautov9-ufs-vhC*
of:N*T*Csamsung,exynosautov9-ufs-vh
of:N*T*Csamsung,exynosautov9-ufsC*
of:N*T*Csamsung,exynosautov9-ufs
of:N*T*Csamsung,exynos7-ufsC*
of:N*T*Csamsung,exynos7-ufs
Signed-off-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240409202203.1308163-1-willmcvicker@google.com
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
