[ Upstream commit bd1c959f37 ]
Add missing "avdd-0v9-supply" and "avdd-1v8-supply" properties to the "hdmi"
node in the Pine64 RockPro64 board dtsi file. To achieve this, also add the
associated "vcca_0v9" regulator that produces the 0.9 V supply, [1][2] which
hasn't been defined previously in the board dtsi file.
This also eliminates the following warnings from the kernel log:
dwhdmi-rockchip ff940000.hdmi: supply avdd-0v9 not found, using dummy regulator
dwhdmi-rockchip ff940000.hdmi: supply avdd-1v8 not found, using dummy regulator
There are no functional changes to the way board works with these additions,
because the "vcc1v8_dvp" and "vcca_0v9" regulators are always enabled, [1][2]
but these additions improve the accuracy of hardware description.
These changes apply to the both supported hardware revisions of the Pine64
RockPro64, i.e. to the production-run revisions 2.0 and 2.1. [1][2]
[1] https://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
[2] https://files.pine64.org/doc/rockpro64/rockpro64_v20-SCH.pdf
Fixes: e4f3fb4909 ("arm64: dts: rockchip: add initial dts support for Rockpro64")
Cc: stable@vger.kernel.org
Suggested-by: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/df3d7e8fe74ed5e727e085b18c395260537bb5ac.1740941097.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1898300abf ]
Sign extend also an unsigned compare value to match what lr.w is doing.
Otherwise try_cmpxchg may spuriously return true when used on a u32 value
that has the sign bit set, as it happens often in inode_set_ctime_current.
Do this in three conversion steps. The first conversion to long is needed
to avoid a -Wpointer-to-int-cast warning when arch_cmpxchg is used with a
pointer type. Then convert to int and back to long to always sign extend
the 32-bit value to 64-bit.
Fixes: 6c58f25e69 ("riscv/atomic: Fix sign extension for RV64I")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Tested-by: Xi Ruoyao <xry111@xry111.site>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/mvmed0k4prh.fsf@suse.de
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d1e420772c upstream.
The signal delivery logic was modified to always set the PKRU bit in
xregs_state->header->xfeatures by this commit:
ae6012d72f ("x86/pkeys: Ensure updated PKRU value is XRSTOR'd")
However, the change derives the bitmask value using XGETBV(1), rather
than simply updating the buffer that already holds the value. Thus, this
approach induces an unnecessary dependency on XGETBV1 for PKRU handling.
Eliminate the dependency by using the established helper function.
Subsequently, remove the now-unused 'mask' argument.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/r/20250416021720.12305-9-chang.seok.bae@intel.com
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64e54461ab upstream.
Currently, saving register states in the signal frame, the legacy feature
bits are always set in xregs_state->header->xfeatures. This code sequence
can be generalized for reuse in similar cases.
Refactor the logic to ensure a consistent approach across similar usages.
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20250416021720.12305-8-chang.seok.bae@intel.com
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f465c148c upstream.
Initialize DR6 by writing its architectural reset value to avoid
incorrectly zeroing DR6 to clear DR6.BLD at boot time, which leads
to a false bus lock detected warning.
The Intel SDM says:
1) Certain debug exceptions may clear bits 0-3 of DR6.
2) BLD induced #DB clears DR6.BLD and any other debug exception
doesn't modify DR6.BLD.
3) RTM induced #DB clears DR6.RTM and any other debug exception
sets DR6.RTM.
To avoid confusion in identifying debug exceptions, debug handlers
should set DR6.BLD and DR6.RTM, and clear other DR6 bits before
returning.
The DR6 architectural reset value 0xFFFF0FF0, already defined as
macro DR6_RESERVED, satisfies these requirements, so just use it to
reinitialize DR6 whenever needed.
Since clear_all_debug_regs() no longer zeros all debug registers,
rename it to initialize_debug_regs() to better reflect its current
behavior.
Since debug_read_clear_dr6() no longer clears DR6, rename it to
debug_read_reset_dr6() to better reflect its current behavior.
Fixes: ebb1064e7c ("x86/traps: Handle #DB for bus lock")
Reported-by: Sohil Mehta <sohil.mehta@intel.com>
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/lkml/06e68373-a92b-472e-8fd9-ba548119770c@intel.com/
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250620231504.2676902-2-xin%40zytor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c55c7a85e0 ]
The subsequent call to os_set_fd_block() overwrites the previous
return value. OR the two return values together to fix it.
Fixes: f88f0bdfc3 ("um: UBD Improvements")
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Link: https://patch.msgid.link/20250606124428.148164-2-tiwei.btw@antgroup.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f73c62d4e upstream.
This reverts commit 61a74ad254 ("riscv: misaligned: fix sleeping function
called during misaligned access handling"). The commit addresses a sleeping
in atomic context problem, but it is not the correct fix as explained by
Clément:
"Using nofault would lead to failure to read from user memory that is paged
out for instance. This is not really acceptable, we should handle user
misaligned access even at an address that would generate a page fault."
This bug has been properly fixed by commit 453805f0a2 ("riscv:
misaligned: enable IRQs while handling misaligned accesses").
Revert this improper fix.
Link: https://lore.kernel.org/linux-riscv/b779beed-e44e-4a5e-9551-4647682b0d21@rivosinc.com/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: 61a74ad254 ("riscv: misaligned: fix sleeping function called during misaligned access handling")
Link: https://lore.kernel.org/r/20250620110939.1642735-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890ba5be63 upstream.
This reverts commit ad5643cf2f ("riscv: Define TASK_SIZE_MAX for
__access_ok()").
This commit changes TASK_SIZE_MAX to be LONG_MAX to optimize access_ok(),
because the previous TASK_SIZE_MAX (default to TASK_SIZE) requires some
computation.
The reasoning was that all user addresses are less than LONG_MAX, and all
kernel addresses are greater than LONG_MAX. Therefore access_ok() can
filter kernel addresses.
Addresses between TASK_SIZE and LONG_MAX are not valid user addresses, but
access_ok() let them pass. That was thought to be okay, because they are
not valid addresses at hardware level.
Unfortunately, one case is missed: get_user_pages_fast() happily accepts
addresses between TASK_SIZE and LONG_MAX. futex(), for instance, uses
get_user_pages_fast(). This causes the problem reported by Robert [1].
Therefore, revert this commit. TASK_SIZE_MAX is changed to the default:
TASK_SIZE.
This unfortunately reduces performance, because TASK_SIZE is more expensive
to compute compared to LONG_MAX. But correctness first, we can think about
optimization later, if required.
Reported-by: <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/linux-riscv/77605.1750245028@localhost/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: ad5643cf2f ("riscv: Define TASK_SIZE_MAX for __access_ok()")
Link: https://lore.kernel.org/r/20250619155858.1249789-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca358692de ]
RISC-V spec explicitly calls out that a local fence.i is not enough for
the code modification to be visble from a remote hart. In fact, it
states:
To make a store to instruction memory visible to all RISC-V harts, the
writing hart also has to execute a data FENCE before requesting that all
remote RISC-V harts execute a FENCE.I.
Although current riscv drivers for IPI use ordered MMIO when sending IPIs
in order to synchronize the action between previous csd writes, riscv
does not restrict itself to any particular flavor of IPI. Any driver or
firmware implementation that does not order data writes before the IPI
may pose a risk for code-modifying race.
Thus, add a fence here to order data writes before making the IPI.
Signed-off-by: Andy Chiu <andybnac@gmail.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20250407180838.42877-8-andybnac@gmail.com
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6767e8784c ]
Segfaults can occur at times where the mmap lock cannot be taken. If
that happens the segfault handler may not be able to take the mmap lock.
Fix the code to use the same approach as most other architectures.
Unfortunately, this requires copying code from mm/memory.c and modifying
it slightly as UML does not have exception tables.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://patch.msgid.link/20250408074524.300153-2-benjamin@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6aba0cb5bb ]
As-per the SBI specification, an SBI remote fence operation applies
to the entire address space if either:
1) start_addr and size are both 0
2) size is equal to 2^XLEN-1
>From the above, only #1 is checked by SBI SFENCE calls so fix the
size parameter check in SBI SFENCE calls to cover #2 as well.
Fixes: 13acfec2db ("RISC-V: KVM: Add remote HFENCE functions based on VCPU requests")
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Link: https://lore.kernel.org/r/20250605061458.196003-2-apatel@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c4abe62342 upstream.
Use "a" constraint for the shift operand of the __pcilg_mio_inuser() inline
assembly. The used "d" constraint allows the compiler to use any general
purpose register for the shift operand, including register zero.
If register zero is used this my result in incorrect code generation:
8f6: a7 0a ff f8 ahi %r0,-8
8fa: eb 32 00 00 00 0c srlg %r3,%r2,0 <----
If register zero is selected to contain the shift value, the srlg
instruction ignores the contents of the register and always shifts zero
bits. Therefore use the "a" constraint which does not permit to select
register zero.
Fixes: f058599e22 ("s390/pci: Fix s390_mmio_read/write with MIO")
Cc: stable@vger.kernel.org
Reported-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f710202b2a upstream.
After commit c104c16073 ("Kunit to check the longest symbol length"),
there is a warning when building with clang because there is now a
definition of unlikely from compiler.h in tools/include/linux, which
conflicts with the one in the instruction decoder selftest:
arch/x86/tools/insn_decoder_test.c:15:9: warning: 'unlikely' macro redefined [-Wmacro-redefined]
Remove the second unlikely() definition, as it is no longer necessary,
clearing up the warning.
Fixes: c104c16073 ("Kunit to check the longest symbol length")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20250318-x86-decoder-test-fix-unlikely-redef-v1-1-74c84a7bf05b@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c104c16073 upstream.
The longest length of a symbol (KSYM_NAME_LEN) was increased to 512
in the reference [1]. This patch adds kunit test suite to check the longest
symbol length. These tests verify that the longest symbol length defined
is supported.
This test can also help other efforts for longer symbol length,
like [2].
The test suite defines one symbol with the longest possible length.
The first test verify that functions with names of the created
symbol, can be called or not.
The second test, verify that the symbols are created (or
not) in the kernel symbol table.
[1] https://lore.kernel.org/lkml/20220802015052.10452-6-ojeda@kernel.org/
[2] https://lore.kernel.org/lkml/20240605032120.3179157-1-song@kernel.org/
Link: https://lore.kernel.org/r/20250302221518.76874-1-sergio.collado@gmail.com
Tested-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Reviewed-by: Rae Moar <rmoar@google.com>
Signed-off-by: Sergio González Collado <sergio.collado@gmail.com>
Link: https://github.com/Rust-for-Linux/linux/issues/504
Reviewed-by: Rae Moar <rmoar@google.com>
Acked-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac954145e1 upstream.
Introduce `rustc-min-version` support function that mimics
`{gcc,clang}-min-version` ones, following commit 88b61e3bff
("Makefile.compiler: replace cc-ifversion with compiler-specific macros").
In addition, use it in the first use case we have in the kernel (which
was done independently to minimize the changes needed for the fix).
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Fiona Behrens <me@Kloenk.dev>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 650768c512 upstream.
Commit 9c006972c3 ("arm64: mmu: drop pXd_present() checks from
pXd_free_pYd_table()") removes the pxd_present() checks because the
caller checks pxd_present(). But, in case of vmap_try_huge_pud(), the
caller only checks pud_present(); pud_free_pmd_page() recurses on each
pmd through pmd_free_pte_page(), wherein the pmd may be none. Thus it is
possible to hit a warning in the latter, since pmd_none => !pmd_table().
Thus, add a pmd_present() check in pud_free_pmd_page().
This problem was found by code inspection.
Fixes: 9c006972c3 ("arm64: mmu: drop pXd_present() checks from pXd_free_pYd_table()")
Cc: stable@vger.kernel.org
Reported-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Dev Jain <dev.jain@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250527082633.61073-1-dev.jain@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b3bc018e8 upstream.
Two 'static inline' TDX helper functions (sc_retry() and
sc_retry_prerr()) take function pointer arguments which refer to
assembly functions. Normally, the compiler inlines the TDX helper,
realizes that the function pointer targets are completely static --
thus can be resolved at compile time -- and generates direct call
instructions.
But, other times (like when CONFIG_CC_OPTIMIZE_FOR_SIZE=y), the
compiler declines to inline the helpers and will instead generate
indirect call instructions.
Indirect calls to assembly functions require special annotation (for
various Control Flow Integrity mechanisms). But TDX assembly
functions lack the special annotations and can only be called
directly.
Annotate both the helpers as '__always_inline' to prod the compiler
into maintaining the direct calls. There is no guarantee here, but
Peter has volunteered to report the compiler bug if this assumption
ever breaks[1].
Fixes: 1e66a7e275 ("x86/virt/tdx: Handle SEAMCALL no entropy error in common code")
Fixes: df01f5ae07 ("x86/virt/tdx: Add SEAMCALL error printing for module initialization")
Signed-off-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/20250605145914.GW39944@noisy.programming.kicks-ass.net/ [1]
Link: https://lore.kernel.org/all/20250606130737.30713-1-kai.huang%40intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee084fa961 upstream.
ERROR INFO:
CPU 25 Unable to handle kernel paging request at virtual address 0x0
...
Call Trace:
[<900000000023c30c>] huge_pte_offset+0x3c/0x58
[<900000000057fd4c>] hugetlb_follow_page_mask+0x74/0x438
[<900000000051fee8>] __get_user_pages+0xe0/0x4c8
[<9000000000522414>] faultin_page_range+0x84/0x380
[<9000000000564e8c>] madvise_vma_behavior+0x534/0xa48
[<900000000056689c>] do_madvise+0x1bc/0x3e8
[<9000000000566df4>] sys_madvise+0x24/0x38
[<90000000015b9e88>] do_syscall+0x78/0x98
[<9000000000221f18>] handle_syscall+0xb8/0x158
In some cases, pmd may be NULL and rely on NULL as the return value for
processing, so it is necessary to determine this situation here.
Cc: stable@vger.kernel.org
Fixes: bd51834d1c ("LoongArch: Return NULL from huge_pte_offset() for invalid PMD")
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52c22661c7 upstream.
When building kernel with LLVM there are occasionally such errors:
In file included from ./include/linux/spinlock.h:59:
In file included from ./include/linux/irqflags.h:17:
arch/loongarch/include/asm/irqflags.h:38:3: error: must not be $r0 or $r1
38 | "csrxchg %[val], %[mask], %[reg]\n\t"
| ^
<inline asm>:1:16: note: instantiated into assembly here
1 | csrxchg $a1, $ra, 0
| ^
To prevent the compiler from allocating $r0 or $r1 for the "mask" of the
csrxchg instruction, the 'q' constraint must be used but Clang < 21 does
not support it. So force to use $t0 in the inline asm, in order to avoid
using $r0/$r1 while keeping the backward compatibility.
Cc: stable@vger.kernel.org
Link: https://github.com/llvm/llvm-project/pull/141037
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Suggested-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e242bbbb6d upstream.
The syscall wrappers use the "a0" register for two different register
variables, both the first argument and the return value. Here the "ret"
variable is used as both input and output while the argument register is
only used as input. Clang treats the conflicting input parameters as an
undefined behaviour and optimizes away the argument assignment.
The code seems to work by chance for the most part today but that may
change in the future. Specifically clock_gettime_fallback() fails with
clockids from 16 to 23, as implemented by the upcoming auxiliary clocks.
Switch the "ret" register variable to a pure output, similar to the
other architectures' vDSO code. This works in both clang and GCC.
Link: https://lore.kernel.org/lkml/20250602102825-42aa84f0-23f1-4d10-89fc-e8bbaffd291a@linutronix.de/
Link: https://lore.kernel.org/lkml/20250519082042.742926976@linutronix.de/
Fixes: c6b99bed6b ("LoongArch: Add VDSO and VSYSCALL support")
Fixes: 18efd0b10e ("LoongArch: vDSO: Wire up getrandom() vDSO implementation")
Cc: stable@vger.kernel.org
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Yanteng Si <si.yanteng@linux.dev>
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 33bc69cf66 ]
VFIO EEH recovery for PCI passthrough devices fails on PowerNV and pseries
platforms due to missing host-side PE bridge reconfiguration. In the
current implementation, eeh_pe_configure() only performs RTAS or OPAL-based
bridge reconfiguration for native host devices, but skips it entirely for
PEs managed through VFIO in guest passthrough scenarios.
This leads to incomplete EEH recovery when a PCI error affects a
passthrough device assigned to a QEMU/KVM guest. Although VFIO triggers the
EEH recovery flow through VFIO_EEH_PE_ENABLE ioctl, the platform-specific
bridge reconfiguration step is silently bypassed. As a result, the PE's
config space is not fully restored, causing subsequent config space access
failures or EEH freeze-on-access errors inside the guest.
This patch fixes the issue by ensuring that eeh_pe_configure() always
invokes the platform's configure_bridge() callback (e.g.,
pseries_eeh_phb_configure_bridge) even for VFIO-managed PEs. This ensures
that RTAS or OPAL calls to reconfigure the PE bridge are correctly issued
on the host side, restoring the PE's configuration space after an EEH
event.
This fix is essential for reliable EEH recovery in QEMU/KVM guests using
VFIO PCI passthrough on PowerNV and pseries systems.
Tested with:
- QEMU/KVM guest using VFIO passthrough (IBM Power9,(lpar)Power11 host)
- Injected EEH errors with pseries EEH errinjct tool on host, recovery
verified on qemu guest.
- Verified successful config space access and CAP_EXP DevCtl restoration
after recovery
Fixes: 212d16cdca ("powerpc/eeh: EEH support for VFIO PCI device")
Signed-off-by: Narayana Murty N <nnmlinux@linux.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250508062928.146043-1-nnmlinux@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93755f408 ]
Building vdso32 on power10 with pcrel leads to following errors:
VDSO32A arch/powerpc/kernel/vdso/gettimeofday-32.o
arch/powerpc/kernel/vdso/gettimeofday.S: Assembler messages:
arch/powerpc/kernel/vdso/gettimeofday.S:40: Error: syntax error; found `@', expected `,'
arch/powerpc/kernel/vdso/gettimeofday.S:71: Info: macro invoked from here
arch/powerpc/kernel/vdso/gettimeofday.S:40: Error: junk at end of line: `@notoc'
arch/powerpc/kernel/vdso/gettimeofday.S:71: Info: macro invoked from here
...
make[2]: *** [arch/powerpc/kernel/vdso/Makefile:85: arch/powerpc/kernel/vdso/gettimeofday-32.o] Error 1
make[1]: *** [arch/powerpc/Makefile:388: vdso_prepare] Error 2
Once the above is fixed, the following happens:
VDSO32C arch/powerpc/kernel/vdso/vgettimeofday-32.o
cc1: error: '-mpcrel' requires '-mcmodel=medium'
make[2]: *** [arch/powerpc/kernel/vdso/Makefile:89: arch/powerpc/kernel/vdso/vgettimeofday-32.o] Error 1
make[1]: *** [arch/powerpc/Makefile:388: vdso_prepare] Error 2
make: *** [Makefile:251: __sub-make] Error 2
Make sure pcrel version of CFUNC() macro is used only for powerpc64
builds and remove -mpcrel for powerpc32 builds.
Fixes: 7e3a68be42 ("powerpc/64: vmlinux support building with PCREL addresing")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/1fa3453f07d42a50a70114da9905bf7b73304fca.1747073669.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed16618c38 ]
TL;DR: SGX page reclaim touches the page to copy its contents to
secondary storage. SGX instructions do not gracefully handle machine
checks. Despite this, the existing SGX code will try to reclaim pages
that it _knows_ are poisoned. Avoid even trying to reclaim poisoned pages.
The longer story:
Pages used by an enclave only get epc_page->poison set in
arch_memory_failure() but they currently stay on sgx_active_page_list until
sgx_encl_release(), with the SGX_EPC_PAGE_RECLAIMER_TRACKED flag untouched.
epc_page->poison is not checked in the reclaimer logic meaning that, if other
conditions are met, an attempt will be made to reclaim an EPC page that was
poisoned. This is bad because 1. we don't want that page to end up added
to another enclave and 2. it is likely to cause one core to shut down
and the kernel to panic.
Specifically, reclaiming uses microcode operations including "EWB" which
accesses the EPC page contents to encrypt and write them out to non-SGX
memory. Those operations cannot handle MCEs in their accesses other than
by putting the executing core into a special shutdown state (affecting
both threads with HT.) The kernel will subsequently panic on the
remaining cores seeing the core didn't enter MCE handler(s) in time.
Call sgx_unmark_page_reclaimable() to remove the affected EPC page from
sgx_active_page_list on memory error to stop it being considered for
reclaiming.
Testing epc_page->poison in sgx_reclaim_pages() would also work but I assume
it's better to add code in the less likely paths.
The affected EPC page is not added to &node->sgx_poison_page_list until
later in sgx_encl_release()->sgx_free_epc_page() when it is EREMOVEd.
Membership on other lists doesn't change to avoid changing any of the
lists' semantics except for sgx_active_page_list. There's a "TBD" comment
in arch_memory_failure() about pre-emptive actions, the goal here is not
to address everything that it may imply.
This also doesn't completely close the time window when a memory error
notification will be fatal (for a not previously poisoned EPC page) --
the MCE can happen after sgx_reclaim_pages() has selected its candidates
or even *inside* a microcode operation (actually easy to trigger due to
the amount of time spent in them.)
The spinlock in sgx_unmark_page_reclaimable() is safe because
memory_failure() runs in process context and no spinlocks are held,
explicitly noted in a mm/memory-failure.c comment.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: balrogg@gmail.com
Cc: linux-sgx@vger.kernel.org
Link: https://lore.kernel.org/r/20250508230429.456271-1-andrew.zaborowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0f4ae7c6ec upstream.
GCC 15 changed the default C standard dialect from gnu17 to gnu23,
which should not have impacted the kernel because it explicitly requests
the gnu11 standard in the main Makefile. However, mips/vdso code uses
its own CFLAGS without a '-std=' value, which break with this dialect
change because of the kernel's own definitions of bool, false, and true
conflicting with the C23 reserved keywords.
include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
Add -std as specified in KBUILD_CFLAGS to the decompressor and purgatory
CFLAGS to eliminate these errors and make the C standard version of these
areas match the rest of the kernel.
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15ac613f12 upstream.
The enum type prot_type declared in arch/s390/kvm/gaccess.c declares an
unfortunate identifier within it - PROT_NONE.
This clashes with the protection bit define from the uapi for mmap()
declared in include/uapi/asm-generic/mman-common.h, which is indeed what
those casually reading this code would assume this to refer to.
This means that any changes which subsequently alter headers in any way
which results in the uapi header being imported here will cause build
errors.
Resolve the issue by renaming PROT_NONE to PROT_TYPE_DUMMY.
Link: https://lkml.kernel.org/r/20250519145657.178365-1-lorenzo.stoakes@oracle.com
Fixes: b3cefd6bf1 ("KVM: s390: Pass initialized arg even if unused")
Signed-off-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Suggested-by: Ignacio Moreno Gonzalez <Ignacio.MorenoGonzalez@kuka.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505140943.IgHDa9s7-lkp@intel.com/
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: Ignacio Moreno Gonzalez <Ignacio.MorenoGonzalez@kuka.com>
Acked-by: Yang Shi <yang@os.amperecomputing.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: James Houghton <jthoughton@google.com>
Cc: Janosch Frank <frankja@linux.ibm.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0ee1d5faf upstream.
Ensure the shadow VMCS cache is evicted during an emergency reboot to
prevent potential memory corruption if the cache is evicted after reboot.
This issue was identified through code inspection, as __loaded_vmcs_clear()
flushes both the normal VMCS and the shadow VMCS.
Avoid checking the "launched" state during an emergency reboot, unlike the
behavior in __loaded_vmcs_clear(). This is important because reboot NMIs
can interfere with operations like copy_shadow_to_vmcs12(), where shadow
VMCSes are loaded directly using VMPTRLD. In such cases, if NMIs occur
right after the VMCS load, the shadow VMCSes will be active but the
"launched" state may not be set.
Fixes: 16f5b9034b ("KVM: nVMX: Copy processor-specific shadow-vmcs to VMCS12")
Cc: stable@vger.kernel.org
Signed-off-by: Chao Gao <chao.gao@intel.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Link: https://lore.kernel.org/r/20250324140849.2099723-1-chao.gao@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bee4838eb upstream.
When freeing a vCPU and thus its VMCB, clear current_vmcb for all possible
CPUs, not just online CPUs, as it's theoretically possible a CPU could go
offline and come back online in conjunction with KVM reusing the page for
a new VMCB.
Link: https://lore.kernel.org/all/20250320013759.3965869-1-yosry.ahmed@linux.dev
Fixes: fd65d3142f ("kvm: svm: Ensure an IBPB on all affected CPUs when freeing a vmcb")
Cc: stable@vger.kernel.org
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Yosry Ahmed <yosry.ahmed@linux.dev>
[sean: split to separate patch, write changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cbb015e2d upstream.
The decompressor is built with the default C dialect, which is now gnu23
on gcc-15, and this clashes with the kernel's bool type definition:
In file included from include/uapi/linux/posix_types.h:5,
from arch/parisc/boot/compressed/misc.c:7:
include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
Add the -std=gnu11 argument here, as we do for all other architectures.
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213205889d upstream.
Change back printk format to 0x%08lx instead of %#08lx, since the latter
does not seem to reliably format the value to 8 hex chars.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.18+
Fixes: e5e9e7f222 ("parisc/unaligned: Enhance user-space visible output")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7397daf102 upstream.
The late init call just writes to omap4 registers as soon as
CONFIG_MFD_CPCAP is enabled without checking whether the
cpcap driver is actually there or the SoC is indeed an
OMAP4.
Rather do these things only with the right device combination.
Fixes booting the BT200 with said configuration enabled and non-factory
X-Loader and probably also some surprising behavior on other devices.
Fixes: c145649bf2 ("ARM: OMAP2+: Configure voltage controller for cpcap to low-speed")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reivewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20250331144439.769697-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96e0b35588 upstream.
arm/memremap: fix arch_memremap_can_ram_remap()
commit 260364d112 ("arm[64]/memremap: don't abuse pfn_valid() to ensure
presence of linear map") added the definition of
arch_memremap_can_ram_remap() for arm[64] specific filtering of what pages
can be used from the linear mapping. memblock_is_map_memory() was called
with the pfn of the address given to arch_memremap_can_ram_remap();
however, memblock_is_map_memory() expects to be given an address for arm,
not a pfn.
This results in calls to memremap() returning a newly mapped area when
it should return an address in the existing linear mapping.
Fix this by removing the address to pfn translation and pass the
address directly.
Fixes: 260364d112 ("arm[64]/memremap: don't abuse pfn_valid() to ensure presence of linear map")
Signed-off-by: Ross Stutterheim <ross.stutterheim@garmin.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b63491838 upstream.
Commit 3ea277194d ("mm, mprotect: flush TLB if potentially racing with
a parallel reclaim leaving stale TLB entries") describes a race that,
prior to the commit, could occur between reclaim and operations such as
mprotect() when using reclaim's tlbbatch mechanism. See that commit for
details but the summary is:
"""
Nadav Amit identified a theoritical race between page reclaim and
mprotect due to TLB flushes being batched outside of the PTL being held.
He described the race as follows:
CPU0 CPU1
---- ----
user accesses memory using RW PTE
[PTE now cached in TLB]
try_to_unmap_one()
==> ptep_get_and_clear()
==> set_tlb_ubc_flush_pending()
mprotect(addr, PROT_READ)
==> change_pte_range()
==> [ PTE non-present - no flush ]
user writes using cached RW PTE
...
try_to_unmap_flush()
"""
The solution was to insert flush_tlb_batched_pending() in mprotect() and
friends to explcitly drain any pending reclaim TLB flushes. In the
modern version of this solution, arch_flush_tlb_batched_pending() is
called to do that synchronisation.
arm64's tlbbatch implementation simply issues TLBIs at queue-time
(arch_tlbbatch_add_pending()), eliding the trailing dsb(ish). The
trailing dsb(ish) is finally issued in arch_tlbbatch_flush() at the end
of the batch to wait for all the issued TLBIs to complete.
Now, the Arm ARM states:
"""
The completion of the TLB maintenance instruction is guaranteed only by
the execution of a DSB by the observer that performed the TLB
maintenance instruction. The execution of a DSB by a different observer
does not have this effect, even if the DSB is known to be executed after
the TLB maintenance instruction is observed by that different observer.
"""
arch_tlbbatch_add_pending() and arch_tlbbatch_flush() conform to this
requirement because they are called from the same task (either kswapd or
caller of madvise(MADV_PAGEOUT)), so either they are on the same CPU or
if the task was migrated, __switch_to() contains an extra dsb(ish).
HOWEVER, arm64's arch_flush_tlb_batched_pending() is also implemented as
a dsb(ish). But this may be running on a CPU remote from the one that
issued the outstanding TLBIs. So there is no architectural gurantee of
synchonization. Therefore we are still vulnerable to the theoretical
race described in Commit 3ea277194d ("mm, mprotect: flush TLB if
potentially racing with a parallel reclaim leaving stale TLB entries").
Fix this by flushing the entire mm in arch_flush_tlb_batched_pending().
This aligns with what the other arches that implement the tlbbatch
feature do.
Cc: <stable@vger.kernel.org>
Fixes: 43b3dfdd04 ("arm64: support batched/deferred tlb shootdown during page reclamation/migration")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Link: https://lore.kernel.org/r/20250530152445.2430295-1-ryan.roberts@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 774a1fa880 upstream.
Prior changes ensured that when zpci_release_device() is called and it
removed the zdev from the zpci_list this instance can not be found via
the zpci_list anymore even while allowing re-add of reserved devices.
This only accounts for the overall lifetime and zpci_list addition and
removal, it does not yet prevent concurrent add of a new instance for
the same underlying device. Such concurrent add would subsequently cause
issues such as attempted re-use of the same IOMMU sysfs directory and is
generally undesired.
Introduce a new zpci_add_remove_lock mutex to serialize adding a new
device with removal. Together this ensures that if a struct zpci_dev is
not found in the zpci_list it was either already removed and torn down,
or its removal and tear down is in progress with the
zpci_add_remove_lock held.
Cc: stable@vger.kernel.org
Fixes: a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b1815a52d upstream.
The architecture assumes that PCI functions can be removed synchronously
as PCI events are processed. This however clashes with the reference
counting of struct pci_dev which allows device drivers to hold on to a
struct pci_dev reference even as the underlying device is removed. To
bridge this gap commit 2a671f77ee ("s390/pci: fix use after free of
zpci_dev") keeps the struct zpci_dev in ZPCI_FN_STATE_RESERVED state
until common code releases the struct pci_dev. Only when all references
are dropped, the struct zpci_dev can be removed and freed.
Later commit a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
moved the deletion of the struct zpci_dev from the zpci_list in
zpci_release_device() to the point where the device is reserved. This
was done to prevent handling events for a device that is already being
removed, e.g. when the platform generates both PCI event codes 0x304
and 0x308. In retrospect, deletion from the zpci_list in the release
function without holding the zpci_list_lock was also racy.
A side effect of this handling is that if the underlying device
re-appears while the struct zpci_dev is in the ZPCI_FN_STATE_RESERVED
state, the new and old instances of the struct zpci_dev and/or struct
pci_dev may clash. For example when trying to create the IOMMU sysfs
files for the new instance. In this case, re-adding the new instance is
aborted. The old instance is removed, and the device will remain absent
until the platform issues another event.
Fix this by allowing the struct zpci_dev to be brought back up right
until it is finally removed. To this end also keep the struct zpci_dev
in the zpci_list until it is finally released when all references have
been dropped.
Deletion from the zpci_list from within the release function is made
safe by using kref_put_lock() with the zpci_list_lock. This ensures that
the releasing code holds the last reference.
Cc: stable@vger.kernel.org
Fixes: a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d76f963329 upstream.
Remove zpci_bus_remove_device() and zpci_disable_device() calls from
zpci_release_device(). These calls were done when the device
transitioned into the ZPCI_FN_STATE_STANDBY state which is guaranteed to
happen before it enters the ZPCI_FN_STATE_RESERVED state. When
zpci_release_device() is called the device is known to be in the
ZPCI_FN_STATE_RESERVED state which is also checked by a WARN_ON().
Cc: stable@vger.kernel.org
Fixes: a46044a92a ("s390/pci: fix zpci_zdev_put() on reserve")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Julian Ruess <julianr@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc0eafd28 upstream.
When a system is being suspended to RAM, the PCI devices are also
suspended and the PPC code ends up calling pseries_msi_compose_msg() and
this triggers the BUG_ON() in __pci_read_msi_msg() because the device at
this point is in reduced power state. In reduced power state, the memory
mapped registers of the PCI device are not accessible.
To replicate the bug:
1. Make sure deep sleep is selected
# cat /sys/power/mem_sleep
s2idle [deep]
2. Make sure console is not suspended (so that dmesg logs are visible)
echo N > /sys/module/printk/parameters/console_suspend
3. Suspend the system
echo mem > /sys/power/state
To fix this behaviour, read the cached msi message of the device when the
device is not in PCI_D0 power state instead of touching the hardware.
Fixes: a5f3d2c17b ("powerpc/pseries/pci: Add MSI domains")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Gautam Menghani <gautam@linux.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250305090237.294633-1-gautam@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e34dbbc85d upstream.
Clear the software event flag in the augmented SS to prevent immediate
repeat of single step trap on return from SIGTRAP handler if the trap
flag (TF) is set without an external debugger attached.
Following is a typical single-stepping flow for a user process:
1) The user process is prepared for single-stepping by setting
RFLAGS.TF = 1.
2) When any instruction in user space completes, a #DB is triggered.
3) The kernel handles the #DB and returns to user space, invoking the
SIGTRAP handler with RFLAGS.TF = 0.
4) After the SIGTRAP handler finishes, the user process performs a
sigreturn syscall, restoring the original state, including
RFLAGS.TF = 1.
5) Goto step 2.
According to the FRED specification:
A) Bit 17 in the augmented SS is designated as the software event
flag, which is set to 1 for FRED event delivery of SYSCALL,
SYSENTER, or INT n.
B) If bit 17 of the augmented SS is 1 and ERETU would result in
RFLAGS.TF = 1, a single-step trap will be pending upon completion
of ERETU.
In step 4) above, the software event flag is set upon the sigreturn
syscall, and its corresponding ERETU would restore RFLAGS.TF = 1.
This combination causes a pending single-step trap upon completion of
ERETU. Therefore, another #DB is triggered before any user space
instruction is executed, which leads to an infinite loop in which the
SIGTRAP handler keeps being invoked on the same user space IP.
Fixes: 14619d912b ("x86/fred: FRED entry/exit and dispatch code")
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250609084054.2083189-2-xin%40zytor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b68e97871 upstream.
io_bitmap_exit() is invoked from exit_thread() when a task exists or
when a fork fails. In the latter case the exit_thread() cleans up
resources which were allocated during fork().
io_bitmap_exit() invokes task_update_io_bitmap(), which in turn ends up
in tss_update_io_bitmap(). tss_update_io_bitmap() operates on the
current task. If current has TIF_IO_BITMAP set, but no bitmap installed,
tss_update_io_bitmap() crashes with a NULL pointer dereference.
There are two issues, which lead to that problem:
1) io_bitmap_exit() should not invoke task_update_io_bitmap() when
the task, which is cleaned up, is not the current task. That's a
clear indicator for a cleanup after a failed fork().
2) A task should not have TIF_IO_BITMAP set and neither a bitmap
installed nor IOPL emulation level 3 activated.
This happens when a kernel thread is created in the context of
a user space thread, which has TIF_IO_BITMAP set as the thread
flags are copied and the IO bitmap pointer is cleared.
Other than in the failed fork() case this has no impact because
kernel threads including IO workers never return to user space and
therefore never invoke tss_update_io_bitmap().
Cure this by adding the missing cleanups and checks:
1) Prevent io_bitmap_exit() to invoke task_update_io_bitmap() if
the to be cleaned up task is not the current task.
2) Clear TIF_IO_BITMAP in copy_thread() unconditionally. For user
space forks it is set later, when the IO bitmap is inherited in
io_bitmap_share().
For paranoia sake, add a warning into tss_update_io_bitmap() to catch
the case, when that code is invoked with inconsistent state.
Fixes: ea5f1cd7ab ("x86/ioperm: Remove bitmap if all permissions dropped")
Reported-by: syzbot+e2b1803445d236442e54@syzkaller.appspotmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/87wmdceom2.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f9bbc1140 upstream.
dm_op hypercalls might come from userspace and pass memory addresses as
parameters. The memory addresses typically correspond to buffers
allocated in userspace to hold extra hypercall parameters.
On ARM, when CONFIG_ARM64_SW_TTBR0_PAN is enabled, they might not be
accessible by Xen, as a result ioreq hypercalls might fail. See the
existing comment in arch/arm64/xen/hypercall.S regarding privcmd_call
for reference.
For privcmd_call, Linux calls uaccess_ttbr0_enable before issuing the
hypercall thanks to commit 9cf09d68b8. We need to do the same for
dm_op. This resolves the problem.
Cc: stable@kernel.org
Fixes: 9cf09d68b8 ("arm64: xen: Enable user access before a privcmd hvc call")
Signed-off-by: Stefano Stabellini <stefano.stabellini@amd.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Message-ID: <alpine.DEB.2.22.394.2505121446370.8380@ubuntu-linux-20-04-desktop>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0d67f0dee6 ]
The user space calls mmap() to map VAS window paste address
and the kernel returns the complete mapped page for each
window. So return -EINVAL if non-zero is passed for offset
parameter to mmap().
See Documentation/arch/powerpc/vas-api.rst for mmap()
restrictions.
Co-developed-by: Jonathan Greental <yonatan02greental@gmail.com>
Signed-off-by: Jonathan Greental <yonatan02greental@gmail.com>
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes: dda44eb29c ("powerpc/vas: Add VAS user space API")
Signed-off-by: Haren Myneni <haren@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-2-maddy@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd097df459 ]
memtrace mmap issue has an out of bounds issue. This patch fixes the by
checking that the requested mapping region size should stay within the
allocated region size.
Reported-by: Jonathan Greental <yonatan02greental@gmail.com>
Fixes: 08a022ad3d ("powerpc/powernv/memtrace: Allow mmaping trace buffers")
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20250610021227.361980-1-maddy@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ba21fa11f ]
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.
Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.
Cc: stable@vger.kernel.org
Fixes: 721e38301b ("arm64: dts: qcom: x1e80100: Add gpu support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-3-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f2b8eed7 ]
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org
Fixes: 4e915987ff ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 600e960604 ]
Ensure the PIR is read exactly once at the start of handle_pending_pir(),
to guarantee that checking for an outstanding posted interrupt in a given
chuck doesn't reload the chunk from the "real" PIR. Functionally, a reload
is benign, but it would defeat the purpose of pre-loading into a copy.
Fixes: 1b03d82ba1 ("x86/irq: Install posted MSI notification handler")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20250401163447.846608-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
