commit b240df2913 upstream.
In commit cfa49ff055 ("media: i2c: imx335: Support 2592x1940 10-bit
mode") the IMX335 driver was extended to support multiple output
bitdepth modes.
This incorrectly extended the frame size enumeration to check against
the supported mbus_codes array instead of the supported mode/frame
array. This has the unwanted side effect of reporting the currently
supported frame size 2592x1944 three times.
Fix the check accordingly to report a frame size for each supported
size, which is presently only a single entry.
Fixes: cfa49ff055 ("media: i2c: imx335: Support 2592x1940 10-bit mode")
Cc: stable@vger.kernel.org
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f639494db4 upstream.
The PLL calculator does a search of the PLL configuration space for all
valid OP pre-PLL clock dividers. The maximum did not take into account the
CCS PLL flag CCS_PLL_FLAG_EXT_IP_PLL_DIVIDER in which case also odd PLL
dividers (other than 1) are valid. Do that now.
Fixes: 4e1e8d240d ("media: ccs-pll: Add support for extended input PLL clock divider")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 660e613d05 upstream.
The ccs_pll_calculate() function does a search over possible PLL
configurations to find the "best" one. If the sensor does not support odd
pre-PLL divisors and the minimum value (with constraints) isn't 1, other
odd values could be errorneously searched (and selected) for the pre-PLL
divisor. Fix this.
Fixes: 415ddd9939 ("media: ccs-pll: Split limits and PLL configuration into front and back parts")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81cf4f46a0 upstream.
When v4l2_subdev_init_finalize() fails no changes have been made to
the runtime-pm device state yet, so the probe_error_media_entity_cleanup
rollback path should not touch the runtime-pm device state.
Instead this should be done from the probe_error_v4l2_subdev_cleanup
rollback path. Note the pm_runtime_xxx() calls are put above
the v4l2_subdev_cleanup() call to have the reverse call order of probe().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Fixes: 289c25923e ("media: ov2740: Use sub-device active state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06d2d478b0 upstream.
The ccs_pll_calculate_vt_tree() function does a search over possible VT
PLL configurations to find the "best" one. If the sensor does not support
odd pre-PLL divisors and the minimum value (with constraints) isn't 1,
other odd values could be errorneously searched (and selected) for the
pre-PLL divisor. Fix this.
Fixes: 415ddd9939 ("media: ccs-pll: Split limits and PLL configuration into front and back parts")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef20527313 upstream.
When setting the sink pad's stream format, set_fmt accidentally changes
the returned format's code to 'outcode', while the purpose is to only
use the 'outcode' for the propagated source stream format.
Fixes: c158d0d4ff ("media: i2c: add DS90UB913 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b122c9cfcb upstream.
CCI_REG_HNUM should be using CCI_REG16_LE() instead of CCI_REG8()
as HNUM spans from 0x302e[0:7] to 0x302f[0:3].
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: 8f0926dba7 ("media: imx335: Use V4L2 CCI for accessing sensor registers")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8268da3c47 upstream.
Probe deferral should not be logged as an error:
ov5675 24-0010: failed to get HW configuration: -517
Drop the (mostly) redundant dev_err() from sensor probe() to suppress
it.
Note that errors during clock and regulator lookup are already correctly
logged using dev_err_probe().
Fixes: 49d9ad719e ("media: ov5675: add device-tree support and support runtime PM")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3d86847fb upstream.
Probe deferral should not be logged as an error:
ov8856 24-0010: failed to get HW configuration: -517
Use dev_err_probe() for the clock lookup and drop the (mostly) redundant
dev_err() from sensor probe() to suppress it.
Note that errors during regulator lookup is already correctly logged
using dev_err_probe().
Fixes: 0c2c7a1e0d ("media: ov8856: Add devicetree support")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3b82d49bf ]
The datasheet for this sensor documents the minimum vblanking as being
32 lines. It does fix some problems with occasional black lines at the
bottom of images (tested on Raspberry Pi).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d7265e2e ]
When calculating D-PHY registers, using data rates that are not multiples
of 16 can lead to precision loss in division operations. This can result in
register values that produce timing violations against the MIPI standard.
An example:
cfg->hs_clk_rate = 294MHz
hf_clk = 18
If the desired value in cfg->init is 100us, which is the minimum allowed
value, then the LINEINITCNT register is calculated as 1799. But since the
actual clock is 18.375MHz instead of 18MHz, this setting results in a time
that is shorter than 100us and thus violates the standard. The correct
value for LINEINITCNT would be 1837.
Improve the precision of calculations by using Hz instead of MHz as unit.
Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a980bc5f56 ]
The register that enables selecting a test-pattern to be outputted in
free-run mode (FREE_RUN_PAT_SEL[2:0]) is only available on adv7280 based
devices, not the adv7180 based ones.
Add a flag to mark devices that are capable of generating test-patterns,
and those that are not. And only register the control on supported
devices.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0aa40f45f ]
When the vblank v4l2 control is set, it does not get written to the
hardware unless exposure is also changed. Change the behavior such that
the vblank is written immediately when the control is set, as setting
the vblank without changing the exposure is a valid use case (such as
for changing the frame rate).
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38985a2568 upstream.
You can't pass uninitialized "ret" variables to cci_write(). It has to
start as zero.
Fixes: 4f0aeba4f1 ("media: i2c: imx214: Convert to CCI register access helpers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebf185efad ]
The driver might skip the ov08x40_identify_module() on probe() based on
the acpi_dev_state_d0() check done in probe().
If the ov08x40_identify_module() call is skipped on probe() it should
be done on the first stream start. Add the missing call.
Note ov08x40_identify_module() will only do something on its first call,
subsequent calls are no-ops.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b1a42fde6e ("media: ov08x40: Avoid sensor probing in D0 state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a39639e44 ]
Move the ov08x40_identify_module() function to above ov08x40_set_stream()
this is a preparation patch for adding a missing ov08x40_identify_module()
call to ov08x40_set_stream().
No functional changes, just moving code around.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: ebf185efad ("media: ov08x40: Add missing ov08x40_identify_module() call on stream-start")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acc294519f ]
The driver defines IMX214_DEFAULT_LINK_FREQ 480000000, and then
IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10),
which works out as 384MPix/s. (The 8 is 4 lanes and DDR.)
Parsing the PLL registers with the defined 24MHz input. We're in single
PLL mode, so MIPI frequency is directly linked to pixel rate. VTCK ends
up being 1200MHz, and VTPXCK and OPPXCK both are 120MHz. Section 5.3
"Frame rate calculation formula" says "Pixel rate
[pixels/s] = VTPXCK [MHz] * 4", so 120 * 4 = 480MPix/s, which basically
agrees with my number above.
3.1.4. MIPI global timing setting says "Output bitrate = OPPXCK * reg
0x113[7:0]", so 120MHz * 10, or 1200Mbit/s. That would be a link
frequency of 600MHz due to DDR.
That also matches to 480MPix/s * 10bpp / 4 lanes / 2 for DDR.
Keep the previous link frequency for backward compatibility.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d55f4eb03 ]
The imx214 camera is capable of either two-lane or four-lane operation.
Currently only the four-lane mode is supported, as proper pixel rates
and link frequences for the two-lane mode are unknown.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 341a133beb ]
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f0aeba4f1 ]
Use the new common CCI register access helpers to replace the private
register access helpers in the imx214 driver. This simplifies the driver
by reducing the amount of code.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d6dc133e6 ]
Error handling in probe() can be a bit simpler with dev_err_probe().
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6832ff659 ]
Port the imx214 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
While at it, simplify imx214_start_streaming() by removing unneeded goto
statements and the corresponding error label.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ccc888d169 upstream.
There were multiple issues in the driver's probe function related to
error handling:
- Device's PM runtime status wasn't reverted to suspended on some errors
in probe.
- Runtime PM was left enabled for the device on some probe errors.
- Device was left powered on if a probe failure happened or when it
was removed when it was powered on.
- An extra pm_runtime_set_suspended() was issued in driver's remove
function when the device was suspended.
Fix these bugs.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42eceae979 upstream.
Set the device's runtime PM status and enable runtime PM before
registering the async sub-device. This is needed to avoid the case where
the device is runtime PM resumed while runtime PM has not been enabled
yet.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 1283b3b8f8 ("media: i2c: Add driver for Sony IMX219 sensor")
Cc: stable@vger.kernel.org # for >= v6.6
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f5ffd3bc6 upstream.
Idle the device only after the async sub-device has been successfully
registered. In error handling, set the device's runtime PM status to
suspended only if it has been set to active previously in probe.
Also set the device's runtime PM status to suspended in remove only if it
wasn't so already.
Fixes: 8a89dc62f2 ("media: add imx319 camera sensor driver")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d391292cd upstream.
Lift the xshutdown (enable) GPIO 1 ms after enabling the regulators, as
required by the sensor's power-up sequence.
Fixes: d30bb512da ("media: Add a driver for the ov7251 camera sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1963698d5 upstream.
Set the enable GPIO low when acquiring it.
Fixes: d30bb512da ("media: Add a driver for the ov7251 camera sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80704d14f1 upstream.
Set the device's runtime PM status to suspended in probe error paths where
it was previously set to active.
Fixes: 9447082ae6 ("[media] smiapp: Implement power-on and power-off sequences without runtime PM")
Cc: stable@vger.kernel.org # for >= v5.15
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e046045830 upstream.
Set the device's runtime PM status to suspended in device removal only if
it wasn't suspended already.
Fixes: 9447082ae6 ("[media] smiapp: Implement power-on and power-off sequences without runtime PM")
Cc: stable@vger.kernel.org # for >= v5.15
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abd8875725 upstream.
This reverts commit 9bc92332cc.
Revert this "fix" as it's not really helpful but makes backporting a
proper fix harder.
Fixes: 9bc92332cc ("media: imx214: Fix the error handling in imx214_probe()")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 591a07588c upstream.
Commit ceddfd4493 ("media: i2c: imx219: Support four-lane operation")
added support for device tree to allow configuration of the sensor to
use 4 lanes with a link frequency of 363MHz, and amended the advertised
pixel rate to 280.8MPix/s.
However it didn't change any of the PLL settings, so actually it would
have been running overclocked in the MIPI block, and with the frame
rate and exposure calculations being wrong as the pixel rate was
unchanged.
The pixel rate and link frequency advertised were taken from the "Clock
Setting Example" section of the datasheet. However those are based on an
external clock of 12MHz, and are unachievable with a clock of 24MHz - it
seems PREPLLCLK_VT_DIV and PREPLLCK_OP_DIV can ONLY be set via the
automatic configuration documented in "9-1-2 EXCK_FREQ setting depend on
INCK frequency", not by writing the registers.
The closest we can get with a 24MHz clock is 281.6MPix/s and 364MHz.
Dropping all support for the 363MHz link frequency would cause problems
for existing users, so allow it, but log a warning that the requested
value is being changed to the supported one.
Fixes: ceddfd4493 ("media: i2c: imx219: Support four-lane operation")
Cc: stable@vger.kernel.org
Co-developed-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Peyton Howe <peyton.howe@bellsouth.net>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed554da65a upstream.
Commit 7d968b5bad ("media: hi556: Return -EPROBE_DEFER if no endpoint is
found") moved the v4l2_fwnode_endpoint_alloc_parse() call in
hi556_check_hwcfg() up, but it did not make the error-exit paths between
the old and new call-site use "goto check_hwcfg_error;" to free the bus_cfg
on errors.
Add the missing "goto check_hwcfg_error;" statements to fix a memleak on
early error-exits from hi556_check_hwcfg().
Fixes: 7d968b5bad ("media: hi556: Return -EPROBE_DEFER if no endpoint is found")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e38acacb9 upstream.
The mask to select the test-pattern in register ADV748X_SDP_FRP is
incorrect, it's the lower 3 bits which controls the pattern. The
GENMASK() macro is used incorrectly and the generated mask is 0x0e
instead of 0x07.
The result is that not all test patterns are selectable, and that in
some cases the wrong test pattern is activated. Fix this by correcting
the GENMASK().
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Cc: stable@vger.kernel.org
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fixed tiny typo in commit log: my -> by]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42d0ec194a upstream.
UB9702 does not have SP and EQ registers, but the driver uses them in
log_status(). Fix this by separating the SP and EQ related log_status()
work into a separate function (for clarity) and calling that function
only for UB960.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5dbbd0609b upstream.
The driver uses a static CSI-2 virtual channel mapping where all virtual
channels from an RX port are mapped to a virtual channel number matching
the RX port number.
The UB960 and UB9702 have different registers for the purpose, and the
UB9702 version is not correct. Each of the VC_ID_MAP registers do not
contain a single mapping, as the driver currently thinks, but two.
This can cause received VCs other than 0 to be mapped in a wrong way.
Fix this by writing both mappings to each register.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 698cf6df87 upstream.
UB9702 doesn't have the registers for SP and EQ. Adjust the code in
ub960_rxport_wait_locks() to not use those registers for UB9702. As
these values are only used for a debug print here, there's no functional
change.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60b45ece41 upstream.
The ub913 and ub953 drivers call fwnode_handle_put(priv->sd.fwnode) as
part of their remove process, and if the driver is removed multiple
times, eventually leads to put "overflow", possibly causing memory
corruption or crash.
The fwnode_handle_put() is a leftover from commit 905f88cceb ("media:
i2c: ds90ub9x3: Fix sub-device matching"), which changed the code
related to the sd.fwnode, but missed removing these fwnode_handle_put()
calls.
Cc: stable@vger.kernel.org
Fixes: 905f88cceb ("media: i2c: ds90ub9x3: Fix sub-device matching")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fdbff0f54 upstream.
ccs_limits is allocated in ccs_read_all_limits() after the allocation of
mdata.backing. Ensure that resources are freed in the reverse order of
their allocation by moving out_free_ccs_limits up.
Fixes: a11d3d6891 ("media: ccs: Read CCS static data from firmware binaries")
Cc: stable@vger.kernel.org
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82b696750f upstream.
The length field of the CCS static data blocks was mishandled, leading to
wrong interpretation of the length header for blocks that are 16 kiB in
size. Such large blocks are very, very rare and so this wasn't found
earlier.
As the length is used as part of input validation, the issue has no
security implications.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 001d375353 upstream.
Light frequency was not properly returned when in auto
mode and the detected frequency was 60Hz.
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sam Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57d10bcac6 upstream.
Add a 2-5ms delay when coming out of standby and before reading the
sensor info register durning probe, as instructed by the datasheet. This
standby delay is already present when the sensor starts streaming.
During a cold-boot, reading the IMX296_SENSOR_INFO register would often
return a value of 0x0000, if this delay is not present before.
Fixes: cb33db2b6c ("media: i2c: IMX296 camera sensor driver")
Cc: stable@vger.kernel.org
Tested-by: Alexandru Ardelean <aardelean@baylibre.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da73efa8e6 upstream.
ccs_data_parse() releases the allocated in-memory data structure when the
parser fails, but it does not clean up parsed metadata that is there to
help access the actual data. Do that, in order to return the data
structure in a sane state.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba3bdb9394 upstream.
UB9702 has the refclk freq register at a different offset than UB960,
but the code uses the UB960's offset for both chips. Fix this.
The refclk freq is only used for a debug print, so there's no functional
change here.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit feaf4154d6 ]
The datasheet lists that "Maximum exposure time is frame
length -25 row periods, where frame length is set by
registers {0x380E, 0x380F}".
However this driver had OV9282_EXPOSURE_OFFSET set to 12
which allowed that restriction to be violated, and would
result in very under-exposed images.
Correct the offset.
Fixes: 14ea315bbe ("media: i2c: Add ov9282 camera sensor driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2055c1d62 ]
Reviewing the datasheets, register 0x3011 is meant to be 0x02 on imx327
and 0x00 on imx290.
Move it out of the common registers, and set it appropriately in the
sensor specific sections. (Included for imx290 to be explicit, rather
than relying on the default value).
Fixes: 2d41947ec2 ("media: i2c: imx290: Add support for imx327 variant")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d0fef6de4f upstream.
It is necessary to account for I2C quirks in the burst mode path of this
driver. Not all I2C controllers can accept arbitrarily long writes and this
is represented in the quirks field of the adapter structure.
Prior to this patch the following error message is seen on a Qualcomm
X1E80100 CRD.
[ 38.773524] i2c i2c-2: adapter quirk: msg too long (addr 0x0036, size 290, write)
[ 38.781454] ov08x40 2-0036: Failed regs transferred: -95
[ 38.787076] ov08x40 2-0036: ov08x40_start_streaming failed to set regs
Fix the error by breaking up the write sequence into the advertised maximum
write size of the quirks field if the quirks field is populated.
Fixes: 8f667d2023 ("media: ov08x40: Reduce start streaming time")
Cc: stable@vger.kernel.org # v6.9+
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
