[ Upstream commit e07dea3de5 ]
The for_each_available_child_of_node() calls of_node_put() to
release child_np in each success loop. After breaking from the
loop with the child_np has been released, the code will jump to
the put_child label and will call the of_node_put() again if the
devm_request_threaded_irq() fails. These cause a double free bug.
Fix by returning directly to avoid the duplicate of_node_put().
Fixes: ed2b5a8e6b ("phy: phy-rockchip-inno-usb2: support muxed interrupts")
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260109154626.2452034-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b246caa680 upstream.
The USB2 Bias Pad Control register manages analog parameters for signal
detection. Previously, the HS_DISCON_LEVEL relied on hardware reset
values, which may lead to the detection failure.
Explicitly configure HS_DISCON_LEVEL to 0x7. This ensures the disconnect
threshold is sufficient to guarantee reliable detection.
Fixes: bbf711682c ("phy: tegra: xusb: Add Tegra186 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://patch.msgid.link/20251212032116.768307-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 028e8ca7b2 upstream.
When the OTG USB port is used to power the SoC, configured as peripheral
and used in gadget mode, there is a disconnection about 6 seconds after the
gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The problem happens because of the PHY driver code flow, summarized as:
* UDC start code (triggered via configfs at any time after boot)
-> phy_init
-> rockchip_usb2phy_init
-> schedule_delayed_work(otg_sm_work [A], 6 sec)
-> phy_power_on
-> rockchip_usb2phy_power_on
-> enable clock
-> rockchip_usb2phy_reset
* Now the gadget interface is up and running.
* 6 seconds later otg_sm_work starts [A]
-> rockchip_usb2phy_otg_sm_work():
if (B_IDLE state && VBUS present && ...):
schedule_delayed_work(&rport->chg_work [B], 0);
* immediately the chg_detect_work starts [B]
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
if (!rport->suspended):
rockchip_usb2phy_power_off() <--- [X]
At [X], the PHY is powered off, causing a disconnection. This quickly
triggers a new connection and following re-enumeration, but any connection
that had been established during the 6 seconds is broken.
The code already checks for !rport->suspended (which, somewhat
counter-intuitively, means the PHY is powered on), so add a guard for VBUS
as well to avoid a disconnection when a cable is connected.
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Co-developed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-1-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2ec4723de upstream.
After U-Boot initializes PCIe with "pcie enum", Linux fails to detect
an NVMe disk on some boot cycles with:
phy phy-32f00000.pcie-phy.0: phy poweron failed --> -110
Discussion with NXP identified that the iMX8MP PCIe PHY PLL may fail to
lock when re-initialized without a reset cycle [1].
The issue reproduces on 7% of tested hardware platforms, with a 30-40%
failure rate per affected device across boot cycles.
Insert a reset cycle in the power-on routine to ensure the PHY is
initialized from a known state.
[1] https://community.nxp.com/t5/i-MX-Processors/iMX8MP-PCIe-initialization-in-U-Boot/m-p/2248437#M242401
Signed-off-by: Rafael Beims <rafael.beims@toradex.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251223150254.1075221-1-rafael@beims.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4914d67da9 upstream.
The mmio regmap that may be allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind.
Fixes: 5ab90f4012 ("phy: ti: gmii-sel: Do not use syscon helper to build regmap")
Cc: stable@vger.kernel.org # 6.14
Cc: Andrew Davis <afd@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20251127134834.2030-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d8f725b79 upstream.
When the OTG USB port is used to power to SoC, configured as peripheral and
used in gadget mode, communication stops without notice about 6 seconds
after the gadget is configured and enumerated.
The problem was observed on a Radxa Rock Pi S board, which can only be
powered by the only USB-C connector. That connector is the only one usable
in gadget mode. This implies the USB cable is connected from before boot
and never disconnects while the kernel runs.
The related code flow in the PHY driver code can be summarized as:
* the first time chg_detect_work starts (6 seconds after gadget is
configured and enumerated)
-> rockchip_chg_detect_work():
if chg_state is UNDEFINED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, false); [Y]
* rockchip_chg_detect_work() changes state and re-triggers itself a few
times until it reaches the DETECTED state:
-> rockchip_chg_detect_work():
if chg_state is DETECTED:
property_enable(base, &rphy->phy_cfg->chg_det.opmode, true); [Z]
At [Y] all existing communications stop. E.g. using a CDC serial gadget,
the /dev/tty* devices are still present on both host and device, but no
data is transferred anymore. The later call with a 'true' argument at [Z]
does not restore it.
Due to the lack of documentation, what chg_det.opmode does exactly is not
clear, however by code inspection it seems reasonable that is disables
something needed to keep the communication working, and testing proves that
disabling these lines lets gadget mode keep working. So prevent changes to
chg_det.opmode when there is a cable connected (VBUS present).
Fixes: 98898f3bc8 ("phy: rockchip-inno-usb2: support otg-port for rk3399")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/lkml/20250414185458.7767aabc@booty/
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20251127-rk3308-fix-usb-gadget-phy-disconnect-v2-2-dac8a02cd2ca@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb21116099 ]
"family" is an enum, thus cast of pointer on 64-bit compile test with
clang W=1 causes:
phy-bcm-ns-usb3.c:206:17: error: cast to smaller integer type 'enum bcm_ns_family' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
This was already fixed in commit bd6e74a2f0 ("phy: broadcom: ns-usb3:
fix Wvoid-pointer-to-enum-cast warning") but then got bad in commit
21bf6fc47a ("phy: Use device_get_match_data()").
Note that after various discussions the preferred cast is via "unsigned
long", not "uintptr_t".
Fixes: 21bf6fc47a ("phy: Use device_get_match_data()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20251224115533.154162-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08aa19de72 ]
devm_pm_runtime_enable() can fail due to memory allocation. The current
code ignores its return value after calling pm_runtime_set_active(),
leaving the device in an inconsistent state if runtime PM initialization
fails.
Check the return value of devm_pm_runtime_enable() and return on
failure. Also move the declaration of 'ret' to the function scope
to support this check.
Fixes: ee8e41b504 ("phy: ti: phy-da8xx-usb: Add runtime PM support")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251124105734.1027-1-vulab@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cabd25b572 ]
The "index" variable is used as an index into the usbphyc->phys[] array
which has usbphyc->nphys elements. So if it is equal to usbphyc->nphys
then it is one element out of bounds. The "index" comes from the
device tree so it's data that we trust and it's unlikely to be wrong,
however it's obviously still worth fixing the bug. Change the > to >=.
Fixes: 94c358da3a ("phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://patch.msgid.link/aTfHcMJK1wFVnvEe@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ca52c0983 ]
Enabling runtime PM before attaching the QPHY instance as driver data
can lead to a NULL pointer dereference in runtime PM callbacks that
expect valid driver data. There is a small window where the suspend
callback may run after PM runtime enabling and before runtime forbid.
This causes a sporadic crash during boot:
```
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a1
[...]
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.7+ #116 PREEMPT
Workqueue: pm pm_runtime_work
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : qusb2_phy_runtime_suspend+0x14/0x1e0 [phy_qcom_qusb2]
lr : pm_generic_runtime_suspend+0x2c/0x44
[...]
```
Attach the QPHY instance as driver data before enabling runtime PM to
prevent NULL pointer dereference in runtime PM callbacks.
Reorder pm_runtime_enable() and pm_runtime_forbid() to prevent a
short window where an unnecessary runtime suspend can occur.
Use the devres-managed version to ensure PM runtime is symmetrically
disabled during driver removal for proper cleanup.
Fixes: 891a96f65a ("phy: qcom-qusb2: Add support for runtime PM")
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://patch.msgid.link/20251219085640.114473-1-loic.poulain@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95463cbb4f ]
Drivers should generally be quiet on successful probe, but this is not
followed by some PHY drivers, for example:
snps-eusb2-hsphy 88e1000.phy: Registered Snps-eUSB2 phy
qcom-eusb2-repeater c432000.spmi:pmic@7:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@a:phy@fd00: Registered Qcom-eUSB2 repeater
qcom-eusb2-repeater c432000.spmi:pmic@b:phy@fd00: Registered Qcom-eUSB2 repeater
snps-eusb2-hsphy fd3000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fd9000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy fde000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e0000.phy: Registered Snps-eUSB2 phy
snps-eusb2-hsphy 88e2000.phy: Registered Snps-eUSB2 phy
Drop (or demote to debug level) unnecessary registration info messages
to make boot logs a little less noisy.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250523085112.11287-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 1ca52c0983 ("phy: qcom-qusb2: Fix NULL pointer dereference on early suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93dbe9b5b3 ]
As the driver now resides outside the phy subdirectory under a different
name, refactor all definitions, structures and functions to explicitly
specify what code is Qualcomm-specific and what is not.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250504144527.1723980-5-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 1ca52c0983 ("phy: qcom-qusb2: Fix NULL pointer dereference on early suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8becf9179a ]
Clear the PCS_TX_SWING_FULL field mask before setting the new value
in PHY_CTRL5 register. Without clearing the mask first, the OR operation
could leave previously set bits, resulting in incorrect register
configuration.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Suggested-by: Leonid Segal <leonids@variscite.com>
Acked-by: Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Reviewed-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://patch.msgid.link/20251219160912.561431-1-stefano.r@variscite.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 356d1924b9 upstream.
Platform drivers can be probed after their init sections have been
discarded (e.g. on probe deferral or manual rebind through sysfs) so the
probe function and match table must not live in init.
Fixes: 783f6d3dcf ("phy: bcm63xx-usbh: Add BCM63xx USBH driver")
Cc: stable@vger.kernel.org # 5.9
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251017054537.6884-1-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8daaced9f5 ]
Due to its relatively low frequency, a noise stemming from the 24MHz PLL
reference clock may traverse the low-pass loop filter of ROPLL, which
could potentially generate some HDMI flash artifacts.
Reduce ROPLL loop bandwidth in an attempt to mitigate the problem.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028-phy-hdptx-fixes-v1-2-ecc642a59d94@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 662bb179d3 ]
If an error occurs after the reset_control_deassert(),
reset_control_assert() must be called, as already done in the remove
function.
Use devm_add_action_or_reset() to add the missing call and simplify the
.remove() function accordingly.
While at it, drop struct rcar_gen3_chan::rstc as it is not used aymore.
[claudiu.beznea: removed "struct reset_control *rstc = data;" from
rcar_gen3_reset_assert(), dropped struct rcar_gen3_chan::rstc]
Fixes: 4eae163753 ("phy: renesas: rcar-gen3-usb2: Add support to initialize the bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://patch.msgid.link/20251023135810.1688415-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c7c19466c ]
The driver for the Rockchip MIPI CSI-2 DPHY uses GRF register offset
value 0 to sort out undefined registers. However, the RK3588 CSIDPHY GRF
this offset is perfectly fine (in fact, register 0 is the only one in
this register file).
Introduce a boolean variable to indicate valid registers and allow writes
to register 0.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Michael Riesch <michael.riesch@collabora.com>
Link: https://lore.kernel.org/r/20250616-rk3588-csi-dphy-v4-4-a4f340a7f0cf@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43bd2c4451 ]
Enable support for data lane rates between 80-160 Mbps cdns dphy
as mentioned in TRM [0] by setting the pll_opdiv field to 16.
This change enables lower resolutions like 640x480 at 60Hz.
[0]: https://www.ti.com/lit/zip/spruil1
(Table 12-552. DPHY_TX_PLL_CTRL Register Field Descriptions)
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Harikrishna Shenoy <h-shenoy@ti.com>
Link: https://lore.kernel.org/r/20250807052002.717807-1-h-shenoy@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c27aaee93 ]
Do read-modify-write so that we re-use the characterized reset value as
specified in TRM [1] to program calibration wait time which defines number
of cycles to wait for after startup state machine is in bandgap enable
state.
This fixes PLL lock timeout error faced while using RPi DSI Panel on TI's
AM62L and J721E SoC since earlier calibration wait time was getting
overwritten to zero value thus failing the PLL to lockup and causing
timeout.
[1] AM62P TRM (Section 14.8.6.3.2.1.1 DPHY_TX_DPHYTX_CMN0_CMN_DIG_TBIT2):
Link: https://www.ti.com/lit/pdf/spruj83
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-3-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 284fb19a3f ]
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled by programming DPHY_CMN_SSM register, but driver was
polling them before the common state machine was enabled which is
incorrect. This is as per the DPHY initialization sequence as mentioned in
J721E TRM [1] at section "12.7.2.4.1.2.1 Start-up Sequence Timing Diagram".
It shows O_CMN_READY polling at the end after common configuration pin
setup where the common configuration pin setup step enables state machine
as referenced in "Table 12-1533. Common Configuration-Related Setup
mentions state machine"
To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after state
machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can re-configure
the PLL by following up a power_off, configure, power_on sequence.
[1]: https://www.ti.com/lit/zip/spruil1
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Tested-by: Harikrishna Shenoy <h-shenoy@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250704125915.1224738-2-devarsht@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 689a54acb5 ]
The DPHY driver does not return the actual hs_clk_rate, so the DSI
driver has no idea what clock was actually achieved. Set the realized
hs_clk_rate to the opts struct, so that the DSI driver gets it back.
Reviewed-by: Aradhya Bhatia <aradhya.bhatia@linux.dev>
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20250723-cdns-dphy-hs-clk-rate-fix-v1-1-d4539d44cbe7@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 284fb19a3f ("phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7bb14b61b7 ]
The boot firmware may disable the U3 port early during boot and leave it
up to the controller or PHY driver to re-enable U3 when needed.
The Rockchip USBDP PHY driver currently does this for RK3576 and RK3588,
something the Rockchip Naneng Combo PHY driver never does for RK3568.
This may result in USB 3.0 ports being limited to only using USB 2.0 or
in special cases not working at all on RK3568.
Write to PIPE_GRF USB3OTGx_CON1 reg to ensure the U3 port is enabled
when a PHY with PHY_TYPE_USB3 mode is used.
Fixes: 7160820d74 ("phy: rockchip: add naneng combo phy for RK3568")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250723072324.2246498-1-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e19bcea997 upstream.
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 918ee0d21b ("usb: phy: omap-usb3: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724131206.2211-4-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 64961557ef upstream.
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 478b6c7436 ("usb: phy: omap-usb2: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724131206.2211-3-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bca065733a upstream.
Make sure to drop the references taken to the PMC OF node and device by
of_parse_phandle() and of_find_device_by_node() during probe.
Note the holding a reference to the PMC device does not prevent the
PMC regmap from going away (e.g. if the PMC driver is unbound) so there
is no need to keep the reference.
Fixes: 2d10214872 ("phy: tegra: xusb: Add wake/sleepwalk for Tegra210")
Cc: stable@vger.kernel.org # 5.14
Cc: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724131206.2211-2-johan@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a3556b81b upstream.
The current configuration used for the IPQ5332 M31 USB PHY fails the
Near End High Speed Signal Quality compliance test. To resolve this,
update the initialization sequence as specified in the Hardware Design
Document.
Fixes: 08e49af507 ("phy: qcom: Introduce M31 USB PHY driver")
Cc: stable@kernel.org
Signed-off-by: Kathiravan Thirumoorthy <kathiravan.thirumoorthy@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250630-ipq5332_hsphy_complaince-v2-1-63621439ebdb@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 25facbabc3 ]
pcie_conf is used to touch TEST_WRITE strobe signal. This signal should
be enabled, a little time waited, and then disabled. Current code clearly
was copy-pasted and never disables the strobe signal. Adjust the define.
While at it, remove PHY_CFG_RD_MASK which has been unused since
64cdc03608 ("phy: rockchip-pcie: remove unused phy_rd_cfg function").
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/d514d5d5627680caafa8b7548cbdfee4307f5440.1751322015.git.geraldogabriel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31bc94de76 ]
Zeroing out registers does not happen in the downstream kernel, and will
"tune" the repeater in surely unexpected ways since most registers don't
have a reset value of 0x0.
Stop doing that and instead just set the registers that are in the init
sequence (though long term I don't think there's actually PMIC-specific
init sequences, there's board specific tuning, but that's a story for
another day).
Fixes: 99a517a582 ("phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250617-eusb2-repeater-tuning-v2-2-ed6c484f18ee@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24c63c590a upstream.
The logic that drives the pad calibration values resides in the
controller reset domain and so the calibration values are only being
captured when the controller is out of reset. However, by clearing the
CYA_TRK_CODE_UPDATE_ON_IDLE bit, the calibration values can be set
while the controller is in reset.
The CYA_TRK_CODE_UPDATE_ON_IDLE bit was previously cleared based on the
trk_hw_mode flag, but this dependency is not necessary. Instead,
introduce a new flag, trk_update_on_idle, to independently control this
bit.
Fixes: d8163a32ca ("phy: tegra: xusb: Add Tegra234 support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250519090929.3132456-2-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefc1caee9 upstream.
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode.
Fixes: 49d46e3c7e ("phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20250502092606.2275682-1-waynec@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b15ee09ddb upstream.
The description of TX_VBOOST_LVL is wrong in register PHY_CTRL3
bit[31:29].
The updated description as below:
011: Corresponds to a launch amplitude of 0.844 V.
100: Corresponds to a launch amplitude of 1.008 V.
101: Corresponds to a launch amplitude of 1.156 V.
This will fix the parsing function
phy_tx_vboost_level_from_property() to return correct value.
Fixes: 63c85ad0cd ("phy: fsl-imx8mp-usb: add support for phy tuning")
Cc: stable@vger.kernel.org
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20250430094502.2723983-3-xu.yang_2@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d14402a38c ]
The qmp_usb_iomap() helper function currently returns the raw result of
devm_ioremap() for non-exclusive mappings. Since devm_ioremap() may return
a NULL pointer and the caller only checks error pointers with IS_ERR(),
NULL could bypass the check and lead to an invalid dereference.
Fix the issue by checking if devm_ioremap() returns NULL. When it does,
qmp_usb_iomap() now returns an error pointer via IOMEM_ERR_PTR(-ENOMEM),
ensuring safe and consistent error handling.
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Fixes: a5d6b1ac56 ("phy: qcom-qmp-usb: fix memleak on probe deferral")
CC: Johan Hovold <johan@kernel.org>
CC: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414125050.2118619-1-chenyuan0y@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0422253ac1 ]
The switch from 1/10 to 1/40 clock ratio must happen when exceeding the
340 MHz rate limit of HDMI 1.4, i.e. when entering the HDMI 2.0 domain,
and not before.
Therefore, use the correct comparison operator '>' instead of '>=' when
checking the max rate. While at it, introduce a define for this rate
limit constant.
Fixes: 553be2830c ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250318-phy-sam-hdptx-bpc-v6-3-8cb1678e7663@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9475055b1 ]
When using HDMI PLL frequency division coefficient at 50.25MHz
that is calculated by rk_hdptx_phy_clk_pll_calc(), it fails to
get PHY LANE lock. Although the calculated values are within the
allowable range of PHY PLL configuration.
In order to fix the PHY LANE lock error and provide the expected
50.25MHz output, manually compute the required PHY PLL frequency
division coefficient and add it to ropll_tmds_cfg configuration
table.
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250427095124.3354439-1-algea.cao@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f097adb9b ]
JH7110 USB 2.0 host fails to detect USB 2.0 devices occasionally. With a
long time of debugging and testing, we found that setting Rx clock gating
control signal to normal power consumption mode can solve this problem.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Link: https://lore.kernel.org/r/20250422101244.51686-1-hal.feng@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21860f340b ]
This code's intention is to configure lane0 and lane2 tunings, but for
lane2 there is a typo and it ends up tuning something else.
Fix the typo, as it doesn't appear to make sense to apply different
tunings for lane0 vs lane2.
The same typo appears to exist in the bootloader, hence we restore the
original value in the typo'd registers as well. This can be removed
once / if the bootloader is updated.
Note that this is incorrect in the downstream driver as well - the
values had been copied from there.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20241206-gs101-phy-lanes-orientation-phy-v4-4-f5961268b149@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d58c04e305 ]
As reported by Damon Ding, the phy_get_mode() call doesn't work as
expected unless the PHY driver has a .set_mode() call. This prompts PHY
drivers to have empty stubs for .set_mode() for the sake of being able
to get the mode.
Make .set_mode() callback truly optional and update PHY's mode even if
it there is none.
Cc: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/96f8310f-93f1-4bcb-8637-137e1159ff83@rock-chips.com
Tested-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250209-phy-fix-set-moe-v2-1-76e248503856@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2947c8065e ]
According to the datasheet, setting the dig_clk_sel bit of CMN_REG(0097)
to 1'b1 selects LCPLL as the reference clock, while setting it to 1'b0
selects the ROPLL.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-2-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 969a38be43 ]
According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.
So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a387ebb9 ]
The phy-rcar-gen3-usb2 driver exposes four individual PHYs that are
requested and configured by PHY users. The struct phy_ops APIs access the
same set of registers to configure all PHYs. Additionally, PHY settings can
be modified through sysfs or an IRQ handler. While some struct phy_ops APIs
are protected by a driver-wide mutex, others rely on individual
PHY-specific mutexes.
This approach can lead to various issues, including:
1/ the IRQ handler may interrupt PHY settings in progress, racing with
hardware configuration protected by a mutex lock
2/ due to msleep(20) in rcar_gen3_init_otg(), while a configuration thread
suspends to wait for the delay, another thread may try to configure
another PHY (with phy_init() + phy_power_on()); re-running the
phy_init() goes to the exact same configuration code, re-running the
same hardware configuration on the same set of registers (and bits)
which might impact the result of the msleep for the 1st configuring
thread
3/ sysfs can configure the hardware (though role_store()) and it can
still race with the phy_init()/phy_power_on() APIs calling into the
drivers struct phy_ops
To address these issues, add a spinlock to protect hardware register access
and driver private data structures (e.g., calls to
rcar_gen3_is_any_rphy_initialized()). Checking driver-specific data remains
necessary as all PHY instances share common settings. With this change,
the existing mutex protection is removed and the cleanup.h helpers are
used.
While at it, to keep the code simpler, do not skip
regulator_enable()/regulator_disable() APIs in
rcar_gen3_phy_usb2_power_on()/rcar_gen3_phy_usb2_power_off() as the
regulators enable/disable operations are reference counted anyway.
Fixes: f3b5a8d9b5 ("phy: rcar-gen3-usb2: Add R-Car Gen3 USB2 PHY driver")
Cc: stable@vger.kernel.org
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de76809f60 ]
Commit 08b0ad375c ("phy: renesas: rcar-gen3-usb2: move IRQ registration
to init") moved the IRQ request operation from probe to
struct phy_ops::phy_init API to avoid triggering interrupts (which lead to
register accesses) while the PHY clocks (enabled through runtime PM APIs)
are not active. If this happens, it results in a synchronous abort.
One way to reproduce this issue is by enabling CONFIG_DEBUG_SHIRQ, which
calls free_irq() on driver removal.
Move the IRQ request and free operations back to probe, and take the
runtime PM state into account in IRQ handler. This commit is preparatory
for the subsequent fixes in this series.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250507125032.565017-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 9ce71e85b2 ("phy: renesas: rcar-gen3-usb2: Assert PLL reset on PHY power off")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 83c178470e upstream.
We used to take a lock in tegra186_utmi_bias_pad_power_on() but now we
have moved the lock into the caller. Unfortunately, when we moved the
lock this unlock was left behind and it results in a double unlock.
Delete it now.
Fixes: b47158fb42 ("phy: tegra: xusb: Use a bitmask for UTMI pad power state tracking")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/aAjmR6To4EnvRl4G@stanley.mountain
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
