[ Upstream commit f8e18abf18 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects truesize instead of DMA
write size. Different assumptions in enetc driver configuration lead to
negative tailroom.
Set frag_size to the same value as frame_sz.
Fixes: 2768b2e2f7 ("net: enetc: register XDP RX queues with frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-9-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69d22c6c4 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead
of DMA write size. Different assumptions in i40e driver configuration lead
to negative tailroom.
Set frag_size to the same value as frame_sz in shared pages mode, use new
helper to set frag_size when AF_XDP ZC is active.
Fixes: a045d2f2d0 ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-7-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f497dc8a6 ]
Current way of handling XDP RxQ info in i40e has a problem, where frag_size
is not updated when xsk_buff_pool is detached or when MTU is changed, this
leads to growing tail always failing for multi-buffer packets.
Couple XDP RxQ info registering with buffer allocations and unregistering
with cleaning the ring.
Fixes: a045d2f2d0 ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-6-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168ff39e47 ]
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. If an IPv6 packet is injected into the interface,
route_shortcircuit() is called and a NULL pointer dereference happens on
neigh_lookup().
BUG: kernel NULL pointer dereference, address: 0000000000000380
Oops: Oops: 0000 [#1] SMP NOPTI
[...]
RIP: 0010:neigh_lookup+0x20/0x270
[...]
Call Trace:
<TASK>
vxlan_xmit+0x638/0x1ef0 [vxlan]
dev_hard_start_xmit+0x9e/0x2e0
__dev_queue_xmit+0xbee/0x14e0
packet_sendmsg+0x116f/0x1930
__sys_sendto+0x1f5/0x200
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x12f/0x1590
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fix this by adding an early check on route_shortcircuit() when protocol
is ETH_P_IPV6. Note that ipv6_mod_enabled() cannot be used here because
VXLAN can be built-in even when IPv6 is built as a module.
Fixes: e15a00aafa ("vxlan: add ipv6 route short circuit support")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Link: https://patch.msgid.link/20260304120357.9778-2-fmancera@suse.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0abc73c8a4 ]
Reset eBPF program pointer to old_prog and do not decrease its ref-count
if mtk_open routine in mtk_xdp_setup() fails.
Fixes: 7c26c20da5 ("net: ethernet: mtk_eth_soc: add basic XDP support")
Suggested-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260303-mtk-xdp-prog-ptr-fix-v2-1-97b6dbbe240f@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cd70e3968 ]
VLAN register accesses on the MAC side require the PHY RX clock to be
active. When the network interface is down, the PHY is suspended and
the RX clock is unavailable, causing VLAN operations to fail with
timeouts.
The VLAN core automatically removes VID 0 after the interface goes down
and re-adds it when it comes back up, so these timeouts happen during
normal interface down/up:
# ip link set end1 down
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
renesas-gbeth 15c40000.ethernet end1: failed to kill vid 0081/0
Adding VLANs while the interface is down also fails:
# ip link add link end1 name end1.10 type vlan id 10
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
RTNETLINK answers: Device or resource busy
To fix this, check if the interface is up before accessing VLAN registers.
The software state is always kept up to date regardless of interface state.
When the interface is brought up, stmmac_vlan_restore() is called
to write the VLAN state to hardware.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-5-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd7ad51253 ]
When the network interface is opened or resumed, a DMA reset is performed,
which resets all hardware state, including VLAN state. Currently, only
the resume path is restoring the VLAN state via
stmmac_restore_hw_vlan_rx_fltr(), but that is incomplete: the VLAN hash
table and the VLAN_TAG control bits are not restored.
Therefore, add stmmac_vlan_restore(), which restores the full VLAN
state by updating both the HW filter entries and the hash table, and
call it from both the open and resume paths.
The VLAN restore is moved outside of phylink_rx_clk_stop_block/unblock
in the resume path because receive clock stop is already disabled when
stmmac supports VLAN.
Also, remove the hash readback code in vlan_restore_hw_rx_fltr() that
attempts to restore VTHM by reading VLAN_HASH_TABLE, as it always reads
zero after DMA reset, making it dead code.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-4-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2cd70e3968 ("net: stmmac: Defer VLAN HW configuration when interface is down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e38200e361 ]
The double VLAN bits (EDVLP, ESVL, DOVLTC) are handled inconsistently
between the two vlan_update_hash() implementations:
- dwxgmac2_update_vlan_hash() explicitly clears the double VLAN bits when
is_double is false, meaning that adding a 802.1Q VLAN will disable
double VLAN mode:
$ ip link add link eth0 name eth0.200 type vlan id 200 protocol 802.1ad
$ ip link add link eth0 name eth0.100 type vlan id 100
# Double VLAN bits no longer set
- vlan_update_hash() sets these bits and only clears them when the last
VLAN has been removed, so double VLAN mode remains enabled even after all
802.1AD VLANs are removed.
Address both issues by tracking the number of active 802.1AD VLANs in
priv->num_double_vlans. Pass this count to stmmac_vlan_update() so both
implementations correctly set the double VLAN bits when any 802.1AD
VLAN is active, and clear them only when none remain.
Also update vlan_update_hash() to explicitly clear the double VLAN bits
when is_double is false, matching the dwxgmac2 behavior.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-3-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2cd70e3968 ("net: stmmac: Defer VLAN HW configuration when interface is down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35dfedce44 ]
stmmac_vlan_rx_add_vid() updates active_vlans and the VLAN hash
register before writing the HW filter entry. If the filter write
fails, it leaves a stale VID in active_vlans and the hash register.
stmmac_vlan_rx_kill_vid() has the reverse problem: it clears
active_vlans before removing the HW filter. On failure, the VID is
gone from active_vlans but still present in the HW filter table.
To fix this, reorder the operations to update the hash table first,
then attempt the HW filter operation. If the HW filter fails, roll
back both the active_vlans bitmap and the hash table by calling
stmmac_vlan_update() again.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2f27363aa ]
The xgbe_powerdown() and xgbe_powerup() functions use spinlocks
(spin_lock_irqsave) while calling functions that may sleep:
- napi_disable() can sleep waiting for NAPI polling to complete
- flush_workqueue() can sleep waiting for pending work items
This causes a "BUG: scheduling while atomic" error during suspend/resume
cycles on systems using the AMD XGBE Ethernet controller.
The spinlock protection in these functions is unnecessary as these
functions are called from suspend/resume paths which are already serialized
by the PM core
Fix this by removing the spinlock. Since only code that takes this lock
is xgbe_powerdown() and xgbe_powerup(), remove it completely.
Fixes: c5aa9e3b81 ("amd-xgbe: Initial AMD 10GbE platform driver")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260302042124.1386445-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4c13ab362 ]
The current implementation in the igb_xsk_wakeup expects
the Rx and Tx queues to share the same irq. This would lead
to triggering of incorrect irq in split irq configuration.
This patch addresses this issue which could impact environments
with 2 active cpu cores
or when the number of queues is reduced to 2 or less
cat /proc/interrupts | grep eno2
167: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
0-edge eno2
168: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
1-edge eno2-rx-0
169: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
2-edge eno2-rx-1
170: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
3-edge eno2-tx-0
171: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
4-edge eno2-tx-1
Furthermore it uses the flags input argument to trigger either rx, tx or
both rx and tx irqs as specified in the ndo_xsk_wakeup api documentation
Fixes: 80f6ccf9f1 ("igb: Introduce XSK data structures and helpers")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b848521701 ]
iavf sets LIBIE_MAX_MTU as netdev->max_mtu, ignoring vf_res->max_mtu
from PF [1]. This allows setting an MTU beyond the actual hardware
limit, causing TX queue timeouts [2].
Set correct netdev->max_mtu using vf_res->max_mtu from the PF.
Note that currently PF drivers such as ice/i40e set the frame size in
vf_res->max_mtu, not MTU. Convert vf_res->max_mtu to MTU before setting
netdev->max_mtu.
[1]
# ip -j -d link show $DEV | jq '.[0].max_mtu'
16356
[2]
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 1: transmit queue 0 timed out 5692 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 6: transmit queue 3 timed out 5312 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
...
Fixes: 5fa4caff59 ("iavf: switch to Page Pool")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eef33aa449 ]
The referenced commit came from a misunderstanding of the FW LLDP filter
AQ (Admin Queue) command due to the error in the internal documentation.
Contrary to the assumptions in the original commit, VFs can be added and
deleted from this filter without any problems. Introduced dev_info message
proved to be useful, so reverting the whole commit does not make sense.
Without this fix, trusted VFs do not receive LLDP traffic, if there is an
AQ LLDP filter on PF. When trusted VF attempts to add an LLDP multicast
MAC address, the following message can be seen in dmesg on host:
ice 0000:33:00.0: Failed to add Rx LLDP rule on VSI 20 error: -95
Revert checking VSI type when adding LLDP filter through AQ.
Fixes: 4d5a1c4e6d ("ice: do not add LLDP-specific filter if not necessary")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e10a730d1 ]
Check frame length before accessing the mgmt fields in
mt76_connac2_mac_write_txwi_80211 in order to avoid a possible oob
access.
Fixes: 577dbc6c65 ("mt76: mt7915: enable offloading of sequence number assignment")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260226-mt76-addba-req-oob-access-v1-3-b0f6d1ad4850@kernel.org
[fix check to also cover mgmt->u.action.u.addba_req.capab,
correct Fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c41a9abd6a ]
Check frame length before accessing the mgmt fields in
mt7925_mac_write_txwi_80211 in order to avoid a possible oob access.
Fixes: c948b5da6b ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260226-mt76-addba-req-oob-access-v1-2-b0f6d1ad4850@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6086284630 ]
Check frame length before accessing the mgmt fields in
mt7996_mac_write_txwi_80211 in order to avoid a possible oob access.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260226-mt76-addba-req-oob-access-v1-1-b0f6d1ad4850@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72c6df8f28 ]
Make sure that wl->mutex is locked before it is unlocked. This has been
detected by the Clang thread-safety analyzer.
Fixes: 45aa7f071b ("wlcore: Use generic runtime pm calls for wowlan elp configuration")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260223220102.2158611-26-bart.vanassche@linux.dev
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d98c24617a ]
cw1200_wow_suspend() must only return with priv->conf_mutex locked if it
returns zero. This mutex must be unlocked if an error is returned. Add
mutex_unlock() calls to the error paths from which that call is missing.
This has been detected by the Clang thread-safety analyzer.
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://patch.msgid.link/20260223220102.2158611-25-bart.vanassche@linux.dev
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c73126ecd ]
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 1cd3b40797 ("octeon_ep_vf: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-5-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43b3160cb6 ]
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 37d79d0596 ("octeon_ep: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-3-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 479d589b40 ]
bond_option_mode_set() already rejects mode changes that would make a
loaded XDP program incompatible via bond_xdp_check(). However,
bond_option_xmit_hash_policy_set() has no such guard.
For 802.3ad and balance-xor modes, bond_xdp_check() returns false when
xmit_hash_policy is vlan+srcmac, because the 802.1q payload is usually
absent due to hardware offload. This means a user can:
1. Attach a native XDP program to a bond in 802.3ad/balance-xor mode
with a compatible xmit_hash_policy (e.g. layer2+3).
2. Change xmit_hash_policy to vlan+srcmac while XDP remains loaded.
This leaves bond->xdp_prog set but bond_xdp_check() now returning false
for the same device. When the bond is later destroyed, dev_xdp_uninstall()
calls bond_xdp_set(dev, NULL, NULL) to remove the program, which hits
the bond_xdp_check() guard and returns -EOPNOTSUPP, triggering:
WARN_ON(dev_xdp_install(dev, mode, bpf_op, NULL, 0, NULL))
Fix this by rejecting xmit_hash_policy changes to vlan+srcmac when an
XDP program is loaded on a bond in 802.3ad or balance-xor mode.
commit 39a0876d59 ("net, bonding: Disallow vlan+srcmac with XDP")
introduced bond_xdp_check() which returns false for 802.3ad/balance-xor
modes when xmit_hash_policy is vlan+srcmac. The check was wired into
bond_xdp_set() to reject XDP attachment with an incompatible policy, but
the symmetric path -- preventing xmit_hash_policy from being changed to an
incompatible value after XDP is already loaded -- was left unguarded in
bond_option_xmit_hash_policy_set().
Note:
commit 094ee6017e ("bonding: check xdp prog when set bond mode")
later added a similar guard to bond_option_mode_set(), but
bond_option_xmit_hash_policy_set() remained unprotected.
Reported-by: syzbot+5a287bcdc08104bc3132@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/6995aff6.050a0220.2eeac1.014e.GAE@google.com/T/
Fixes: 39a0876d59 ("net, bonding: Disallow vlan+srcmac with XDP")
Signed-off-by: Jiayuan Chen <jiayuan.chen@shopee.com>
Link: https://patch.msgid.link/20260226080306.98766-2-jiayuan.chen@linux.dev
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cbe98f7be ]
Function rtl8365mb_phy_ocp_write() always returns 0, even when an error
occurs during register access. This patch fixes the return value to
propagate the actual error code from regmap operations.
Link: https://lore.kernel.org/netdev/a2dfde3c-d46f-434b-9d16-1e251e449068@yahoo.com/
Fixes: 2796728460 ("net: dsa: realtek: rtl8365mb: serialize indirect PHY register access")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260301-realtek_namiltd_fix1-v1-1-43a6bb707f9c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d973b1039c ]
This triggers a WARN_ON in ieee80211_hw_conf_init and isn't the expected
behavior from the driver - other drivers default to 0 too.
Fixes: 0a44dfc070 ("wifi: mac80211: simplify non-chanctx drivers")
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Link: https://patch.msgid.link/20260221-rsi-config-ret-v1-1-9a8f805e2f31@puri.sm
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab3f894de2 ]
The mcp251x_open() function call free_irq() in its error path with the
mpc_lock mutex held. But if an interrupt already occurred the
interrupt handler will be waiting for the mpc_lock and free_irq() will
deadlock waiting for the handler to finish.
This issue is similar to the one fixed in commit 7dd9c26bd6 ("can:
mcp251x: fix deadlock if an interrupt occurs during mcp251x_open") but
for the error path.
To solve this issue move the call to free_irq() after the lock is
released. Setting `priv->force_quit = 1` beforehand ensure that the IRQ
handler will exit right away once it acquired the lock.
Signed-off-by: Alban Bedel <alban.bedel@lht.dlh.de>
Link: https://patch.msgid.link/20260209144706.2261954-1-alban.bedel@lht.dlh.de
Fixes: bf66f3736a ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9439a661c2 ]
Extend the MAC_TCR_SS (Speed Select) register field width from 2 bits
to 3 bits to properly support all speed settings.
The MAC_TCR register's SS field encoding requires 3 bits to represent
all supported speeds:
- 0x00: 10Gbps (XGMII)
- 0x02: 2.5Gbps (GMII) / 100Mbps
- 0x03: 1Gbps / 10Mbps
- 0x06: 2.5Gbps (XGMII) - P100a only
With only 2 bits, values 0x04-0x07 cannot be represented, which breaks
2.5G XGMII mode on newer platforms and causes incorrect speed select
values to be programmed.
Fixes: 07445f3c7c ("amd-xgbe: Add support for 10 Mbps speed")
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260226170753.250312-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 147792c395 ]
When both eth interfaces with links up are added to a bridge or hsr
interface, ping fails if the link speed is not 1Gbps (e.g., 100Mbps).
The issue is seen because when switching to offload (bridge/hsr) mode,
prueth_emac_restart() restarts the firmware and clears DRAM with
memset_io(), setting all memory to 0. This includes PORT_LINK_SPEED_OFFSET
which firmware reads for link speed. The value 0 corresponds to
FW_LINK_SPEED_1G (0x00), so for 1Gbps links the default value is correct
and ping works. For 100Mbps links, the firmware needs FW_LINK_SPEED_100M
(0x01) but gets 0 instead, causing ping to fail. The function
emac_adjust_link() is called to reconfigure, but it detects no state change
(emac->link is still 1, speed/duplex match PHY) so new_state remains false
and icssg_config_set_speed() is never called to correct the firmware speed
value.
The fix resets emac->link to 0 before calling emac_adjust_link() in
prueth_emac_common_start(). This forces new_state=true, ensuring
icssg_config_set_speed() is called to write the correct speed value to
firmware memory.
Fixes: 06feac1540 ("net: ti: icssg-prueth: Fix emac link speed handling")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20260226102356.2141871-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74badb9c20 ]
Commit 31a7a0bbeb ("dpaa2-switch: add bounds check for if_id in IRQ
handler") introduces a range check for if_id to avoid an out-of-bounds
access. If an out-of-bounds if_id is detected, the interrupt status is
not cleared. This may result in an interrupt storm.
Clear the interrupt status after detecting an out-of-bounds if_id to avoid
the problem.
Found by an experimental AI code review agent at Google.
Fixes: 31a7a0bbeb ("dpaa2-switch: add bounds check for if_id in IRQ handler")
Cc: Junrui Luo <moonafterrain@outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260227055812.1777915-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be11a53722 ]
In the current implementation, flushing multicast entries in MAC mode
incorrectly deletes entries for all ports instead of only the target port,
disrupting multicast traffic on other ports. The cause is adding multicast
entries by setting only host port bit, and not setting the MAC port bits.
Fix this by setting the MAC port's bit in the port mask while adding the
multicast entry. Also fix the flush logic to preserve the host port bit
during removal of MAC port and free ALE entries when mask contains only
host port.
Fixes: 5c50a856d5 ("drivers: net: ethernet: cpsw: add multicast address to ALE table")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224181359.2055322-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0942fc6d32 ]
Panther Lake systems introduced an autonomous power gating feature for
the integrated Gigabit Ethernet in shutdown state (S5) state. As part of
it, the reset value of DPG_EN bit was changed to 1. Clear this bit after
performing hardware reset to avoid errors such as Tx/Rx hangs, or packet
loss/corruption.
Fixes: 0c9183ce61 ("e1000e: Add support for the next LOM generation")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b3d54a85b ]
Using get_cpu() in the tracepoint assignment causes an obvious preempt
count leak because nothing invokes put_cpu() to undo it:
softirq: huh, entered softirq 3 NET_RX with preempt_count 00000100, exited with 00000101?
This clearly has seen a lot of testing in the last 3+ years...
Use smp_processor_id() instead.
Fixes: 6d4d584a7e ("i40e: Add i40e_napi_poll tracepoint")
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6aa07e23dd ]
Fix IRDMA hardware initialization timeout (-110) after resume by
separating VSI-dependent configuration from RDMA resource allocation,
ensuring VSI is rebuilt before IRDMA accesses it.
After resume from suspend, IRDMA hardware initialization fails:
ice: IRDMA hardware initialization FAILED init_state=4 status=-110
Separate RDMA initialization into two phases:
1. ice_init_rdma() - Allocate resources only (no VSI/QoS access, no plug)
2. ice_rdma_finalize_setup() - Assign VSI/QoS info and plug device
This allows:
- ice_init_rdma() to stay in ice_resume() (mirrors ice_deinit_rdma()
in ice_suspend())
- VSI assignment deferred until after ice_vsi_rebuild() completes
- QoS info updated after ice_dcb_rebuild() completes
- Device plugged only when control queues, VSI, and DCB are all ready
Fixes: bc69ad7486 ("ice: avoid IRQ collision to fix init failure on ACPI S3 resume")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c31557336 ]
When deleting a flow rule using "ethtool -N <dev> delete <location>",
idpf_sideband_action_ena() incorrectly validates fsp->ring_cookie even
though ethtool doesn't populate this field for delete operations. The
uninitialized ring_cookie may randomly match RX_CLS_FLOW_DISC or
RX_CLS_FLOW_WAKE, causing validation to fail and preventing legitimate
rule deletions. Remove the unnecessary sideband action enable check and
ring_cookie validation during delete operations since action validation
is not required when removing existing rules.
Fixes: ada3e24b84 ("idpf: add flow steering support")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1500a8662d ]
The code uses the vidx for the IRQ name but that doesn't match ethtool
reporting nor netdev naming, this makes it hard to tune the device and
associate queues with IRQs. Sequentially requesting irqs starting from
'0' makes the output consistent.
This commit changes the interrupt numbering but preserves the name
format, maintaining ABI compatibility. Existing tools relying on the old
numbering are already non-functional, as they lack a useful correlation
to the interrupts.
Before:
ethtool -L eth1 tx 1 combined 3
grep . /proc/irq/*/*idpf*/../smp_affinity_list
/proc/irq/67/idpf-Mailbox-0/../smp_affinity_list:0-55,112-167
/proc/irq/68/idpf-eth1-TxRx-1/../smp_affinity_list:0
/proc/irq/70/idpf-eth1-TxRx-3/../smp_affinity_list:1
/proc/irq/71/idpf-eth1-TxRx-4/../smp_affinity_list:2
/proc/irq/72/idpf-eth1-Tx-5/../smp_affinity_list:3
ethtool -S eth1 | grep -v ': 0'
NIC statistics:
tx_q-0_pkts: 1002
tx_q-1_pkts: 2679
tx_q-2_pkts: 1113
tx_q-3_pkts: 1192 <----- tx_q-3 vs idpf-eth1-Tx-5
rx_q-0_pkts: 1143
rx_q-1_pkts: 3172
rx_q-2_pkts: 1074
After:
ethtool -L eth1 tx 1 combined 3
grep . /proc/irq/*/*idpf*/../smp_affinity_list
/proc/irq/67/idpf-Mailbox-0/../smp_affinity_list:0-55,112-167
/proc/irq/68/idpf-eth1-TxRx-0/../smp_affinity_list:0
/proc/irq/70/idpf-eth1-TxRx-1/../smp_affinity_list:1
/proc/irq/71/idpf-eth1-TxRx-2/../smp_affinity_list:2
/proc/irq/72/idpf-eth1-Tx-3/../smp_affinity_list:3
ethtool -S eth1 | grep -v ': 0'
NIC statistics:
tx_q-0_pkts: 118
tx_q-1_pkts: 134
tx_q-2_pkts: 228
tx_q-3_pkts: 138 <--- tx_q-3 matches idpf-eth1-Tx-3
rx_q-0_pkts: 111
rx_q-1_pkts: 366
rx_q-2_pkts: 120
Fixes: d4d5587182 ("idpf: initialize interrupts and enable vport")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712896ac4b ]
Currently, in idpf_wait_for_sw_marker_completion(), when an
IDPF_TXD_COMPLT_SW_MARKER packet is found, the routine breaks out of
the for loop and does not increment the next_to_clean counter. This
causes the subsequent NAPI polls to run into the same
IDPF_TXD_COMPLT_SW_MARKER packet again and print out the following:
[ 23.261341] idpf 0000:05:00.0 eth1: Unknown TX completion type: 5
Instead, we should increment next_to_clean regardless when an
IDPF_TXD_COMPLT_SW_MARKER packet is found.
Tested: with the patch applied, we do not see the errors above from NAPI
polls anymore.
Fixes: 9d39447051 ("idpf: remove SW marker handling from NAPI")
Signed-off-by: Li Li <boolli@google.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 14eb64db8f upstream.
The dwmac databook for v3.74a states that lpi_intr_o is a sideband
signal which should be used to ungate the application clock, and this
signal is synchronous to the receive clock. The receive clock can run
at 2.5, 25 or 125MHz depending on the media speed, and can stop under
the control of the link partner. This means that the time it takes to
clear is dependent on the negotiated media speed, and thus can be 8,
40, or 400ns after reading the LPI control and status register.
It has been observed with some aggressive link partners, this clock
can stop while lpi_intr_o is still asserted, meaning that the signal
remains asserted for an indefinite period that the local system has
no direct control over.
The LPI interrupts will still be signalled through the main interrupt
path in any case, and this path is not dependent on the receive clock.
This, since we do not gate the application clock, and the chances of
adding clock gating in the future are slim due to the clocks being
ill-defined, lpi_intr_o serves no useful purpose. Remove the code which
requests the interrupt, and all associated code.
Reported-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Tested-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com> # Renesas RZ/V2H board
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vnJbt-00000007YYN-28nm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8dbdc6e38 upstream.
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c>] __dev_open+0x280/0x2b0
[ 1362.080384] [<806d7668>] __dev_change_flags+0x244/0x24c
[ 1362.085598] [<806d7698>] dev_change_flags+0x28/0x78
[ 1362.090528] [<807150e4>] dev_ioctl+0x4c0/0x654 <-- Hold lock "rtnl_mutex" by calling rtnl_lock();
[ 1362.094985] [<80694360>] sock_ioctl+0x2f4/0x4e0
[ 1362.099567] [<802e9c4c>] sys_ioctl+0x32c/0xd8c
[ 1362.104022] [<80014504>] syscall_common+0x34/0x58
Here LED_TRIGGER_PHY is registering LED triggers during phy_attach
while holding RTNL and then taking triggers_list_lock.
[ 1362.191101] [<806c2640>] register_netdevice_notifier+0x60/0x168 <-- Trying to get lock "rtnl_mutex" via rtnl_lock();
[ 1362.197073] [<805504ac>] netdev_trig_activate+0x194/0x1e4
[ 1362.202490] [<8054e28c>] led_trigger_set+0x1d4/0x360 <-- Hold lock "triggers_list_lock" by down_read(&triggers_list_lock);
[ 1362.207511] [<8054eb38>] led_trigger_write+0xd8/0x14c
[ 1362.212566] [<80381d98>] sysfs_kf_bin_write+0x80/0xbc
[ 1362.217688] [<8037fcd8>] kernfs_fop_write_iter+0x17c/0x28c
[ 1362.223174] [<802cbd70>] vfs_write+0x21c/0x3c4
[ 1362.227712] [<802cc0c4>] ksys_write+0x78/0x12c
[ 1362.232164] [<80014504>] syscall_common+0x34/0x58
Here LEDS_TRIGGER_NETDEV is being enabled on an LED. It first takes
triggers_list_lock and then RTNL. A classical AB-BA deadlock.
phy_led_triggers_registers() does not require the RTNL, it does not
make any calls into the network stack which require protection. There
is also no requirement the PHY has been attached to a MAC, the
triggers only make use of phydev state. This allows the call to
phy_led_triggers_registers() to be placed elsewhere. PHY probe() and
release() don't hold RTNL, so solving the AB-BA deadlock.
Reported-by: Shiji Yang <yangshiji66@outlook.com>
Closes: https://lore.kernel.org/all/OS7PR01MB13602B128BA1AD3FA38B6D1FFBC69A@OS7PR01MB13602.jpnprd01.prod.outlook.com/
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://patch.msgid.link/20260222152601.1978655-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb868db5f4 upstream.
In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA
buffer cleanup path. It iterates num_bufs times and attempts to unmap
entries in the dma array.
This leads to two issues:
1. The dma array shares storage with tx_qpl_buf_ids (union).
Interpreting buffer IDs as DMA addresses results in attempting to
unmap incorrect memory locations.
2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed
the size of the dma array, causing out-of-bounds access warnings
(trace below is how we noticed this issue).
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of
range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]')
Workqueue: gve gve_service_task [gve]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0xa0
__ubsan_handle_out_of_bounds+0xdc/0x110
gve_tx_stop_ring_dqo+0x182/0x200 [gve]
gve_close+0x1be/0x450 [gve]
gve_reset+0x99/0x120 [gve]
gve_service_task+0x61/0x100 [gve]
process_scheduled_works+0x1e9/0x380
Fix this by properly checking for QPL mode and delegating to
gve_free_tx_qpl_bufs() to reclaim the buffers.
Cc: stable@vger.kernel.org
Fixes: a6fb8d5a8b ("gve: Tx path for DQO-QPL")
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260220215324.1631350-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03cc8f90d0 upstream.
The lbs_free_adapter() function uses timer_delete() (non-synchronous)
for both command_timer and tx_lockup_timer before the structure is
freed. This is incorrect because timer_delete() does not wait for
any running timer callback to complete.
If a timer callback is executing when lbs_free_adapter() is called,
the callback will access freed memory since lbs_cfg_free() frees the
containing structure immediately after lbs_free_adapter() returns.
Both timer callbacks (lbs_cmd_timeout_handler and lbs_tx_lockup_handler)
access priv->driver_lock, priv->cur_cmd, priv->dev, and other fields,
which would all be use-after-free violations.
Use timer_delete_sync() instead to ensure any running timer callback
has completed before returning.
This bug was introduced in commit 8f641d93c3 ("libertas: detect TX
lockups and reset hardware") where del_timer() was used instead of
del_timer_sync() in the cleanup path. The command_timer has had the
same issue since the driver was first written.
Fixes: 8f641d93c3 ("libertas: detect TX lockups and reset hardware")
Fixes: 954ee164f4 ("[PATCH] libertas: reorganize and simplify init sequence")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hodges <git@danielhodges.dev>
Link: https://patch.msgid.link/20260206195356.15647-1-git@danielhodges.dev
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51f9478072 upstream.
If a write urb fails then more needs to be done other than just logging
the message, otherwise the transmission could be stalled. Properly
increment the error counters and wake up the queues so that data will
continue to flow.
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022334-slackness-dynamic-9195@gregkh
Fixes: 88da174369 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7299b1b39a upstream.
If an interrupt urb is received that is not the correct length, properly
detect it and don't attempt to treat the data as valid.
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022331-opal-evaluator-a928@gregkh
Fixes: 88da174369 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5eaad4f768 upstream.
When submitting an urb, that is using the anchor pattern, it needs to be
anchored before submitting it otherwise it could be leaked if
usb_kill_anchored_urbs() is called. This logic is correctly done
elsewhere in the driver, except in the read bulk callback so do that
here also.
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Tested-by: Vincent Mailhol <mailhol@kernel.org>
Link: https://patch.msgid.link/2026022320-poser-stiffly-9d84@gregkh
Fixes: 8537257874 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e446fd058 upstream.
If a broken ucan device gets a message with the message length field set
to 0, then the driver will loop for forever in
ucan_read_bulk_callback(), hanging the system. If the length is 0, just
skip the message and go on to the next one.
This has been fixed in the kvaser_usb driver in the past in commit
0c73772cd2 ("can: kvaser_usb: leaf: Fix potential infinite loop in
command parsers"), so there must be some broken devices out there like
this somewhere.
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022319-huff-absurd-6a18@gregkh
Fixes: 9f2d3eae88 ("can: ucan: add driver for Theobroma Systems UCAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 952caa5da1 upstream.
When submitting an urb, that is using the anchor pattern, it needs to be
anchored before submitting it otherwise it could be leaked if
usb_kill_anchored_urbs() is called. This logic is correctly done
elsewhere in the driver, except in the read bulk callback so do that
here also.
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022334-starlight-scaling-2cea@gregkh
Fixes: 88da174369 ("can: usb: f81604: add Fintek F81604 support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38a01c9700 upstream.
When looking at the data in a USB urb, the actual_length is the size of
the buffer passed to the driver, not the transfer_buffer_length which is
set by the driver as the max size of the buffer.
When parsing the messages in ems_usb_read_bulk_callback() properly check
the size both at the beginning of parsing the message to make sure it is
big enough for the expected structure, and at the end of the message to
make sure we don't overflow past the end of the buffer for the next
message.
Cc: Vincent Mailhol <mailhol@kernel.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@kernel.org
Assisted-by: gkh_clanker_2000
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022316-answering-strainer-a5db@gregkh
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11de1d3ae5 upstream.
The pegasus driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
Cc: Petko Manolov <petkan@nucleusys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026022347-legibly-attest-cc5c@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c58b6c29a4 upstream.
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Link: https://patch.msgid.link/2026022326-shack-headstone-ef6f@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b063c002c upstream.
The kaweth driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://patch.msgid.link/2026022305-substance-virtual-c728@gregkh
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
