[ Upstream commit f8e18abf18 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects truesize instead of DMA
write size. Different assumptions in enetc driver configuration lead to
negative tailroom.
Set frag_size to the same value as frame_sz.
Fixes: 2768b2e2f7 ("net: enetc: register XDP RX queues with frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-9-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69d22c6c4 ]
The only user of frag_size field in XDP RxQ info is
bpf_xdp_frags_increase_tail(). It clearly expects whole buffer size instead
of DMA write size. Different assumptions in i40e driver configuration lead
to negative tailroom.
Set frag_size to the same value as frame_sz in shared pages mode, use new
helper to set frag_size when AF_XDP ZC is active.
Fixes: a045d2f2d0 ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-7-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f497dc8a6 ]
Current way of handling XDP RxQ info in i40e has a problem, where frag_size
is not updated when xsk_buff_pool is detached or when MTU is changed, this
leads to growing tail always failing for multi-buffer packets.
Couple XDP RxQ info registering with buffer allocations and unregistering
with cleaning the ring.
Fixes: a045d2f2d0 ("i40e: set xdp_rxq_info::frag_size")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://patch.msgid.link/20260305111253.2317394-6-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0abc73c8a4 ]
Reset eBPF program pointer to old_prog and do not decrease its ref-count
if mtk_open routine in mtk_xdp_setup() fails.
Fixes: 7c26c20da5 ("net: ethernet: mtk_eth_soc: add basic XDP support")
Suggested-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20260303-mtk-xdp-prog-ptr-fix-v2-1-97b6dbbe240f@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cd70e3968 ]
VLAN register accesses on the MAC side require the PHY RX clock to be
active. When the network interface is down, the PHY is suspended and
the RX clock is unavailable, causing VLAN operations to fail with
timeouts.
The VLAN core automatically removes VID 0 after the interface goes down
and re-adds it when it comes back up, so these timeouts happen during
normal interface down/up:
# ip link set end1 down
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
renesas-gbeth 15c40000.ethernet end1: failed to kill vid 0081/0
Adding VLANs while the interface is down also fails:
# ip link add link end1 name end1.10 type vlan id 10
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
RTNETLINK answers: Device or resource busy
To fix this, check if the interface is up before accessing VLAN registers.
The software state is always kept up to date regardless of interface state.
When the interface is brought up, stmmac_vlan_restore() is called
to write the VLAN state to hardware.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-5-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd7ad51253 ]
When the network interface is opened or resumed, a DMA reset is performed,
which resets all hardware state, including VLAN state. Currently, only
the resume path is restoring the VLAN state via
stmmac_restore_hw_vlan_rx_fltr(), but that is incomplete: the VLAN hash
table and the VLAN_TAG control bits are not restored.
Therefore, add stmmac_vlan_restore(), which restores the full VLAN
state by updating both the HW filter entries and the hash table, and
call it from both the open and resume paths.
The VLAN restore is moved outside of phylink_rx_clk_stop_block/unblock
in the resume path because receive clock stop is already disabled when
stmmac supports VLAN.
Also, remove the hash readback code in vlan_restore_hw_rx_fltr() that
attempts to restore VTHM by reading VLAN_HASH_TABLE, as it always reads
zero after DMA reset, making it dead code.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-4-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2cd70e3968 ("net: stmmac: Defer VLAN HW configuration when interface is down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e38200e361 ]
The double VLAN bits (EDVLP, ESVL, DOVLTC) are handled inconsistently
between the two vlan_update_hash() implementations:
- dwxgmac2_update_vlan_hash() explicitly clears the double VLAN bits when
is_double is false, meaning that adding a 802.1Q VLAN will disable
double VLAN mode:
$ ip link add link eth0 name eth0.200 type vlan id 200 protocol 802.1ad
$ ip link add link eth0 name eth0.100 type vlan id 100
# Double VLAN bits no longer set
- vlan_update_hash() sets these bits and only clears them when the last
VLAN has been removed, so double VLAN mode remains enabled even after all
802.1AD VLANs are removed.
Address both issues by tracking the number of active 802.1AD VLANs in
priv->num_double_vlans. Pass this count to stmmac_vlan_update() so both
implementations correctly set the double VLAN bits when any 802.1AD
VLAN is active, and clear them only when none remain.
Also update vlan_update_hash() to explicitly clear the double VLAN bits
when is_double is false, matching the dwxgmac2 behavior.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-3-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 2cd70e3968 ("net: stmmac: Defer VLAN HW configuration when interface is down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35dfedce44 ]
stmmac_vlan_rx_add_vid() updates active_vlans and the VLAN hash
register before writing the HW filter entry. If the filter write
fails, it leaves a stale VID in active_vlans and the hash register.
stmmac_vlan_rx_kill_vid() has the reverse problem: it clears
active_vlans before removing the HW filter. On failure, the VID is
gone from active_vlans but still present in the HW filter table.
To fix this, reorder the operations to update the hash table first,
then attempt the HW filter operation. If the HW filter fails, roll
back both the active_vlans bitmap and the hash table by calling
stmmac_vlan_update() again.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2f27363aa ]
The xgbe_powerdown() and xgbe_powerup() functions use spinlocks
(spin_lock_irqsave) while calling functions that may sleep:
- napi_disable() can sleep waiting for NAPI polling to complete
- flush_workqueue() can sleep waiting for pending work items
This causes a "BUG: scheduling while atomic" error during suspend/resume
cycles on systems using the AMD XGBE Ethernet controller.
The spinlock protection in these functions is unnecessary as these
functions are called from suspend/resume paths which are already serialized
by the PM core
Fix this by removing the spinlock. Since only code that takes this lock
is xgbe_powerdown() and xgbe_powerup(), remove it completely.
Fixes: c5aa9e3b81 ("amd-xgbe: Initial AMD 10GbE platform driver")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260302042124.1386445-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4c13ab362 ]
The current implementation in the igb_xsk_wakeup expects
the Rx and Tx queues to share the same irq. This would lead
to triggering of incorrect irq in split irq configuration.
This patch addresses this issue which could impact environments
with 2 active cpu cores
or when the number of queues is reduced to 2 or less
cat /proc/interrupts | grep eno2
167: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
0-edge eno2
168: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
1-edge eno2-rx-0
169: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
2-edge eno2-rx-1
170: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
3-edge eno2-tx-0
171: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
4-edge eno2-tx-1
Furthermore it uses the flags input argument to trigger either rx, tx or
both rx and tx irqs as specified in the ndo_xsk_wakeup api documentation
Fixes: 80f6ccf9f1 ("igb: Introduce XSK data structures and helpers")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b848521701 ]
iavf sets LIBIE_MAX_MTU as netdev->max_mtu, ignoring vf_res->max_mtu
from PF [1]. This allows setting an MTU beyond the actual hardware
limit, causing TX queue timeouts [2].
Set correct netdev->max_mtu using vf_res->max_mtu from the PF.
Note that currently PF drivers such as ice/i40e set the frame size in
vf_res->max_mtu, not MTU. Convert vf_res->max_mtu to MTU before setting
netdev->max_mtu.
[1]
# ip -j -d link show $DEV | jq '.[0].max_mtu'
16356
[2]
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 1: transmit queue 0 timed out 5692 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 6: transmit queue 3 timed out 5312 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
...
Fixes: 5fa4caff59 ("iavf: switch to Page Pool")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eef33aa449 ]
The referenced commit came from a misunderstanding of the FW LLDP filter
AQ (Admin Queue) command due to the error in the internal documentation.
Contrary to the assumptions in the original commit, VFs can be added and
deleted from this filter without any problems. Introduced dev_info message
proved to be useful, so reverting the whole commit does not make sense.
Without this fix, trusted VFs do not receive LLDP traffic, if there is an
AQ LLDP filter on PF. When trusted VF attempts to add an LLDP multicast
MAC address, the following message can be seen in dmesg on host:
ice 0000:33:00.0: Failed to add Rx LLDP rule on VSI 20 error: -95
Revert checking VSI type when adding LLDP filter through AQ.
Fixes: 4d5a1c4e6d ("ice: do not add LLDP-specific filter if not necessary")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c73126ecd ]
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 1cd3b40797 ("octeon_ep_vf: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-5-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43b3160cb6 ]
Utilize READ_ONCE and WRITE_ONCE APIs for IO queue Tx/Rx
variable access to prevent compiler optimization and reordering.
Additionally, ensure IO queue OUT/IN_CNT registers are flushed
by performing a read-back after writing.
The compiler could reorder reads/writes to pkts_pending, last_pkt_count,
etc., causing stale values to be used when calculating packets to process
or register updates to send to hardware. The Octeon hardware requires a
read-back after writing to OUT_CNT/IN_CNT registers to ensure the write
has been flushed through any posted write buffers before the interrupt
resend bit is set. Without this, we have observed cases where the hardware
didn't properly update its internal state.
wmb/rmb only provides ordering guarantees but doesn't prevent the compiler
from performing optimizations like caching in registers, load tearing etc.
Fixes: 37d79d0596 ("octeon_ep: add Tx/Rx processing and interrupt support")
Signed-off-by: Sathesh Edara <sedara@marvell.com>
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Signed-off-by: Vimlesh Kumar <vimleshk@marvell.com>
Link: https://patch.msgid.link/20260227091402.1773833-3-vimleshk@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9439a661c2 ]
Extend the MAC_TCR_SS (Speed Select) register field width from 2 bits
to 3 bits to properly support all speed settings.
The MAC_TCR register's SS field encoding requires 3 bits to represent
all supported speeds:
- 0x00: 10Gbps (XGMII)
- 0x02: 2.5Gbps (GMII) / 100Mbps
- 0x03: 1Gbps / 10Mbps
- 0x06: 2.5Gbps (XGMII) - P100a only
With only 2 bits, values 0x04-0x07 cannot be represented, which breaks
2.5G XGMII mode on newer platforms and causes incorrect speed select
values to be programmed.
Fixes: 07445f3c7c ("amd-xgbe: Add support for 10 Mbps speed")
Co-developed-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Guruvendra Punugupati <Guruvendra.Punugupati@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260226170753.250312-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 147792c395 ]
When both eth interfaces with links up are added to a bridge or hsr
interface, ping fails if the link speed is not 1Gbps (e.g., 100Mbps).
The issue is seen because when switching to offload (bridge/hsr) mode,
prueth_emac_restart() restarts the firmware and clears DRAM with
memset_io(), setting all memory to 0. This includes PORT_LINK_SPEED_OFFSET
which firmware reads for link speed. The value 0 corresponds to
FW_LINK_SPEED_1G (0x00), so for 1Gbps links the default value is correct
and ping works. For 100Mbps links, the firmware needs FW_LINK_SPEED_100M
(0x01) but gets 0 instead, causing ping to fail. The function
emac_adjust_link() is called to reconfigure, but it detects no state change
(emac->link is still 1, speed/duplex match PHY) so new_state remains false
and icssg_config_set_speed() is never called to correct the firmware speed
value.
The fix resets emac->link to 0 before calling emac_adjust_link() in
prueth_emac_common_start(). This forces new_state=true, ensuring
icssg_config_set_speed() is called to write the correct speed value to
firmware memory.
Fixes: 06feac1540 ("net: ti: icssg-prueth: Fix emac link speed handling")
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20260226102356.2141871-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74badb9c20 ]
Commit 31a7a0bbeb ("dpaa2-switch: add bounds check for if_id in IRQ
handler") introduces a range check for if_id to avoid an out-of-bounds
access. If an out-of-bounds if_id is detected, the interrupt status is
not cleared. This may result in an interrupt storm.
Clear the interrupt status after detecting an out-of-bounds if_id to avoid
the problem.
Found by an experimental AI code review agent at Google.
Fixes: 31a7a0bbeb ("dpaa2-switch: add bounds check for if_id in IRQ handler")
Cc: Junrui Luo <moonafterrain@outlook.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/20260227055812.1777915-1-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be11a53722 ]
In the current implementation, flushing multicast entries in MAC mode
incorrectly deletes entries for all ports instead of only the target port,
disrupting multicast traffic on other ports. The cause is adding multicast
entries by setting only host port bit, and not setting the MAC port bits.
Fix this by setting the MAC port's bit in the port mask while adding the
multicast entry. Also fix the flush logic to preserve the host port bit
during removal of MAC port and free ALE entries when mask contains only
host port.
Fixes: 5c50a856d5 ("drivers: net: ethernet: cpsw: add multicast address to ALE table")
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224181359.2055322-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0942fc6d32 ]
Panther Lake systems introduced an autonomous power gating feature for
the integrated Gigabit Ethernet in shutdown state (S5) state. As part of
it, the reset value of DPG_EN bit was changed to 1. Clear this bit after
performing hardware reset to avoid errors such as Tx/Rx hangs, or packet
loss/corruption.
Fixes: 0c9183ce61 ("e1000e: Add support for the next LOM generation")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b3d54a85b ]
Using get_cpu() in the tracepoint assignment causes an obvious preempt
count leak because nothing invokes put_cpu() to undo it:
softirq: huh, entered softirq 3 NET_RX with preempt_count 00000100, exited with 00000101?
This clearly has seen a lot of testing in the last 3+ years...
Use smp_processor_id() instead.
Fixes: 6d4d584a7e ("i40e: Add i40e_napi_poll tracepoint")
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Cc: Tony Nguyen <anthony.l.nguyen@intel.com>
Cc: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6aa07e23dd ]
Fix IRDMA hardware initialization timeout (-110) after resume by
separating VSI-dependent configuration from RDMA resource allocation,
ensuring VSI is rebuilt before IRDMA accesses it.
After resume from suspend, IRDMA hardware initialization fails:
ice: IRDMA hardware initialization FAILED init_state=4 status=-110
Separate RDMA initialization into two phases:
1. ice_init_rdma() - Allocate resources only (no VSI/QoS access, no plug)
2. ice_rdma_finalize_setup() - Assign VSI/QoS info and plug device
This allows:
- ice_init_rdma() to stay in ice_resume() (mirrors ice_deinit_rdma()
in ice_suspend())
- VSI assignment deferred until after ice_vsi_rebuild() completes
- QoS info updated after ice_dcb_rebuild() completes
- Device plugged only when control queues, VSI, and DCB are all ready
Fixes: bc69ad7486 ("ice: avoid IRQ collision to fix init failure on ACPI S3 resume")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c31557336 ]
When deleting a flow rule using "ethtool -N <dev> delete <location>",
idpf_sideband_action_ena() incorrectly validates fsp->ring_cookie even
though ethtool doesn't populate this field for delete operations. The
uninitialized ring_cookie may randomly match RX_CLS_FLOW_DISC or
RX_CLS_FLOW_WAKE, causing validation to fail and preventing legitimate
rule deletions. Remove the unnecessary sideband action enable check and
ring_cookie validation during delete operations since action validation
is not required when removing existing rules.
Fixes: ada3e24b84 ("idpf: add flow steering support")
Signed-off-by: Sreedevi Joshi <sreedevi.joshi@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1500a8662d ]
The code uses the vidx for the IRQ name but that doesn't match ethtool
reporting nor netdev naming, this makes it hard to tune the device and
associate queues with IRQs. Sequentially requesting irqs starting from
'0' makes the output consistent.
This commit changes the interrupt numbering but preserves the name
format, maintaining ABI compatibility. Existing tools relying on the old
numbering are already non-functional, as they lack a useful correlation
to the interrupts.
Before:
ethtool -L eth1 tx 1 combined 3
grep . /proc/irq/*/*idpf*/../smp_affinity_list
/proc/irq/67/idpf-Mailbox-0/../smp_affinity_list:0-55,112-167
/proc/irq/68/idpf-eth1-TxRx-1/../smp_affinity_list:0
/proc/irq/70/idpf-eth1-TxRx-3/../smp_affinity_list:1
/proc/irq/71/idpf-eth1-TxRx-4/../smp_affinity_list:2
/proc/irq/72/idpf-eth1-Tx-5/../smp_affinity_list:3
ethtool -S eth1 | grep -v ': 0'
NIC statistics:
tx_q-0_pkts: 1002
tx_q-1_pkts: 2679
tx_q-2_pkts: 1113
tx_q-3_pkts: 1192 <----- tx_q-3 vs idpf-eth1-Tx-5
rx_q-0_pkts: 1143
rx_q-1_pkts: 3172
rx_q-2_pkts: 1074
After:
ethtool -L eth1 tx 1 combined 3
grep . /proc/irq/*/*idpf*/../smp_affinity_list
/proc/irq/67/idpf-Mailbox-0/../smp_affinity_list:0-55,112-167
/proc/irq/68/idpf-eth1-TxRx-0/../smp_affinity_list:0
/proc/irq/70/idpf-eth1-TxRx-1/../smp_affinity_list:1
/proc/irq/71/idpf-eth1-TxRx-2/../smp_affinity_list:2
/proc/irq/72/idpf-eth1-Tx-3/../smp_affinity_list:3
ethtool -S eth1 | grep -v ': 0'
NIC statistics:
tx_q-0_pkts: 118
tx_q-1_pkts: 134
tx_q-2_pkts: 228
tx_q-3_pkts: 138 <--- tx_q-3 matches idpf-eth1-Tx-3
rx_q-0_pkts: 111
rx_q-1_pkts: 366
rx_q-2_pkts: 120
Fixes: d4d5587182 ("idpf: initialize interrupts and enable vport")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 712896ac4b ]
Currently, in idpf_wait_for_sw_marker_completion(), when an
IDPF_TXD_COMPLT_SW_MARKER packet is found, the routine breaks out of
the for loop and does not increment the next_to_clean counter. This
causes the subsequent NAPI polls to run into the same
IDPF_TXD_COMPLT_SW_MARKER packet again and print out the following:
[ 23.261341] idpf 0000:05:00.0 eth1: Unknown TX completion type: 5
Instead, we should increment next_to_clean regardless when an
IDPF_TXD_COMPLT_SW_MARKER packet is found.
Tested: with the patch applied, we do not see the errors above from NAPI
polls anymore.
Fixes: 9d39447051 ("idpf: remove SW marker handling from NAPI")
Signed-off-by: Li Li <boolli@google.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 14eb64db8f upstream.
The dwmac databook for v3.74a states that lpi_intr_o is a sideband
signal which should be used to ungate the application clock, and this
signal is synchronous to the receive clock. The receive clock can run
at 2.5, 25 or 125MHz depending on the media speed, and can stop under
the control of the link partner. This means that the time it takes to
clear is dependent on the negotiated media speed, and thus can be 8,
40, or 400ns after reading the LPI control and status register.
It has been observed with some aggressive link partners, this clock
can stop while lpi_intr_o is still asserted, meaning that the signal
remains asserted for an indefinite period that the local system has
no direct control over.
The LPI interrupts will still be signalled through the main interrupt
path in any case, and this path is not dependent on the receive clock.
This, since we do not gate the application clock, and the chances of
adding clock gating in the future are slim due to the clocks being
ill-defined, lpi_intr_o serves no useful purpose. Remove the code which
requests the interrupt, and all associated code.
Reported-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Tested-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com> # Renesas RZ/V2H board
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vnJbt-00000007YYN-28nm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb868db5f4 upstream.
In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA
buffer cleanup path. It iterates num_bufs times and attempts to unmap
entries in the dma array.
This leads to two issues:
1. The dma array shares storage with tx_qpl_buf_ids (union).
Interpreting buffer IDs as DMA addresses results in attempting to
unmap incorrect memory locations.
2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed
the size of the dma array, causing out-of-bounds access warnings
(trace below is how we noticed this issue).
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of
range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]')
Workqueue: gve gve_service_task [gve]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0xa0
__ubsan_handle_out_of_bounds+0xdc/0x110
gve_tx_stop_ring_dqo+0x182/0x200 [gve]
gve_close+0x1be/0x450 [gve]
gve_reset+0x99/0x120 [gve]
gve_service_task+0x61/0x100 [gve]
process_scheduled_works+0x1e9/0x380
Fix this by properly checking for QPL mode and delegating to
gve_free_tx_qpl_bufs() to reclaim the buffers.
Cc: stable@vger.kernel.org
Fixes: a6fb8d5a8b ("gve: Tx path for DQO-QPL")
Signed-off-by: Ankit Garg <nktgrg@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260220215324.1631350-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffe68c3766 ]
dma_free_coherent() in error path takes priv->rx_buf.alloc_len as
the dma handle. This would lead to improper unmapping of the buffer.
Change the dma handle to priv->rx_buf.alloc_phys.
Fixes: 6af55ff52b ("Driver for Beckhoff CX5020 EtherCAT master module.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Link: https://patch.msgid.link/20260213164340.77272-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d03e094473 ]
The ID 8086:104f is matched by both i40e and ipw2200. The same device
ID should not be in more than one driver, because in that case, which
driver is used is unpredictable. Fix this by taking advantage of the
fact that i40e devices use PCI_CLASS_NETWORK_ETHERNET and ipw2200
devices use PCI_CLASS_NETWORK_OTHER to differentiate the devices.
Fixes: 2e45d3f467 ("i40e: Add support for X710 B/P & SFP+ cards")
Cc: stable@vger.kernel.org
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Link: https://patch.msgid.link/20260210021235.16315-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf9cf80cab ]
In commit 99537d5c47 ("net: macb: Relocate mog_init_rings() callback
from macb_mac_link_up() to macb_open()"), the mog_init_rings() callback
was moved from macb_mac_link_up() to macb_open() to resolve a deadlock
issue. However, this change introduced a tx/rx malfunction following
phy link down and up events. The issue arises from a mismatch between
the software queue->tx_head, queue->tx_tail, queue->rx_prepared_head,
and queue->rx_tail values and the hardware's internal tx/rx queue
pointers.
According to the Zynq UltraScale TRM [1], when tx/rx is disabled, the
internal tx queue pointer resets to the value in the tx queue base
address register, while the internal rx queue pointer remains unchanged.
The following is quoted from the Zynq UltraScale TRM:
When transmit is disabled, with bit [3] of the network control register
set low, the transmit-buffer queue pointer resets to point to the address
indicated by the transmit-buffer queue base address register. Disabling
receive does not have the same effect on the receive-buffer queue
pointer.
Additionally, there is no need to reset the RBQP and TBQP registers in a
phy event callback. Therefore, move macb_init_buffers() to macb_open().
In a phy link up event, the only required action is to reset the tx
software head and tail pointers to align with the hardware's behavior.
[1] https://docs.amd.com/v/u/en-US/ug1085-zynq-ultrascale-trm
Fixes: 99537d5c47 ("net: macb: Relocate mog_init_rings() callback from macb_mac_link_up() to macb_open()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260208-macb-init-ring-v1-1-939a32c14635@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3998b6e90 ]
Commit 95540ad674 ("net: ti: icssg-prueth: Add support for HSR frame
forward offload") introduced support for offloading HSR frame forwarding,
which relies on functions such as is_hsr_master() provided by the HSR
module. Although HSR provides stubs for configurations with HSR
disabled, this driver still requires an optional dependency on HSR.
Otherwise, build failures will occur when icssg-prueth is built-in
while HSR is configured as a module.
ld.lld: error: undefined symbol: is_hsr_master
>>> referenced by icssg_prueth.c:710 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:710)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:681 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:681)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_add_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:1812 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:1812)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(prueth_netdevice_event) in archive vmlinux.a
ld.lld: error: undefined symbol: hsr_get_port_ndev
>>> referenced by icssg_prueth.c:712 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:712)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:712 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:712)
>>> drivers/net/etherneteth_hsr_del_mcast) in archive vmlinux.a
>>> referenced by icssg_prueth.c:683 (drivers/net/ethernet/ti/icssg/icssg_prueth.c:683)
>>> drivers/net/ethernet/ti/icssg/icssg_prueth.o:(icssg_prueth_hsr_add_mcast) in archive vmlinux.a
>>> referenced 1 more times
Fixes: 95540ad674 ("net: ti: icssg-prueth: Add support for HSR frame forward offload")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260207-icssg-dep-v3-1-8c47c1937f81@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3def995c4e ]
The RX/TX flow-control bitmaps (rx_fc_pfvf_bmap and tx_fc_pfvf_bmap)
are allocated by cgx_lmac_init() but never freed in cgx_lmac_exit().
Unbinding and rebinding the driver therefore triggers kmemleak:
unreferenced object (size 16):
backtrace:
rvu_alloc_bitmap
cgx_probe
Free both bitmaps during teardown.
Fixes: e740003874 ("octeontx2-af: Flow control resource management")
Cc: stable@vger.kernel.org
Signed-off-by: Bo Sun <bo@mboxify.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260206130925.1087588-2-bo@mboxify.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d01103fdcb ]
The ID 1186:4302 is matched by both r8169 and skge. The same device ID
should not be in more than one driver, because in that case, which
driver is used is unpredictable. I downloaded the latest drivers for
all hardware revisions of the D-Link DGE-530T from D-Link's website,
and the only drivers which contain this ID are Realtek drivers.
Therefore, remove this device ID from skge.
In the kernel bug report which requested addition of this device ID,
someone created a patch to add the ID to skge. Then, it was pointed
out that this device is an "r8169 in disguise", and a patch was created
to add it to r8169. Somehow, both of these patches got merged. See the
link below.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=38862
Fixes: c074304c2b ("add pci-id for DGE-530T")
Cc: stable@vger.kernel.org
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260206071724.15268-1-enelsonmoore@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d724b34fb ]
If an error occurs during register_netdev() for the first MAC in
cpsw_register_ports(), even though cpsw->slaves[0].ndev is set to NULL,
cpsw->slaves[1].ndev would remain unchanged. This could later cause
cpsw_unregister_ports() to attempt unregistering the second MAC.
To address this, add a check for ndev->reg_state before calling
unregister_netdev(). With this change, setting cpsw->slaves[i].ndev
to NULL becomes unnecessary and can be removed accordingly.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://patch.msgid.link/20260205-cpsw-error-path-v1-2-6e58bae6b299@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62db84b7ef ]
The current error handling in cpsw_probe() has two issues:
- cpsw_unregister_ports() may be called before cpsw_register_ports() has
been executed.
- cpsw_unregister_ports() is already invoked within cpsw_register_ports()
in case of a register_netdev() failure, but the error path would call
it again.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://patch.msgid.link/20260205-cpsw-error-path-v1-1-6e58bae6b299@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a5752c6dc ]
The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes()
but never validates it against DPSW_MAX_IF (64). This value controls
iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices
into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports
num_ifs >= 64, the loop can write past the array bounds.
Add a bound check for num_ifs in dpaa2_switch_init().
dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port
num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all
ports match the flood filter, the loop fills all 64 slots and the control
interface write overflows by one entry.
The check uses >= because num_ifs == DPSW_MAX_IF is also functionally
broken.
build_if_id_bitmap() silently drops any ID >= 64:
if (id[i] < DPSW_MAX_IF)
bmap[id[i] / 64] |= ...
Fixes: 539dda3c5d ("staging: dpaa2-switch: properly setup switching domains")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/SYBPR01MB78812B47B7F0470B617C408AAF74A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 859380694f ]
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430
Fixes: cee137a634 ("net/mlx5e: Handle ESN update events")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60253042c0 ]
The cited commit miss to add locking in the error path of
mlx5_sriov_enable(). When pci_enable_sriov() fails,
mlx5_device_disable_sriov() is called to clean up. This cleanup function
now expects to be called with the devlink instance lock held.
Add the missing devl_lock(devlink) and devl_unlock(devlink)
Fixes: 84a433a40d ("net/mlx5: Lock mlx5 devlink reload callbacks")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7073e8b97 ]
The cited commit introduced MLX5_PRIV_FLAGS_SWITCH_LEGACY to identify
when a transition to legacy mode is requested via devlink. However, the
logic failed to clear this flag if the mode was subsequently changed
back to MLX5_ESWITCH_OFFLOADS (switchdev). Consequently, if a user
toggled from legacy to switchdev, the flag remained set, leaving the
driver with wrong state indicating
Fix this by explicitly clearing the MLX5_PRIV_FLAGS_SWITCH_LEGACY bit
when the requested mode is MLX5_ESWITCH_OFFLOADS.
Fixes: 2a4f56fbcc ("net/mlx5e: Keep netdev when leave switchdev for devlink set legacy only")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd7b9f83fb ]
mlx5_lag_disable_change() unconditionally called mlx5_disable_lag() when
LAG was active, which is incorrect for MLX5_LAG_MODE_MPESW.
Hnece, call mlx5_disable_mpesw() when running in MPESW mode.
Fixes: a32327a3a0 ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260224114652.1787431-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f975a09552 ]
While testing corner cases in the driver, a use-after-free crash
was found on the service rescan PCI path.
When mana_serv_reset() calls mana_gd_suspend(), mana_gd_cleanup()
destroys gc->service_wq. If the subsequent mana_gd_resume() fails
with -ETIMEDOUT or -EPROTO, the code falls through to
mana_serv_rescan() which triggers pci_stop_and_remove_bus_device().
This invokes the PCI .remove callback (mana_gd_remove), which calls
mana_gd_cleanup() a second time, attempting to destroy the already-
freed workqueue. Fix this by NULL-checking gc->service_wq in
mana_gd_cleanup() and setting it to NULL after destruction.
Call stack of issue for reference:
[Sat Feb 21 18:53:48 2026] Call Trace:
[Sat Feb 21 18:53:48 2026] <TASK>
[Sat Feb 21 18:53:48 2026] mana_gd_cleanup+0x33/0x70 [mana]
[Sat Feb 21 18:53:48 2026] mana_gd_remove+0x3a/0xc0 [mana]
[Sat Feb 21 18:53:48 2026] pci_device_remove+0x41/0xb0
[Sat Feb 21 18:53:48 2026] device_remove+0x46/0x70
[Sat Feb 21 18:53:48 2026] device_release_driver_internal+0x1e3/0x250
[Sat Feb 21 18:53:48 2026] device_release_driver+0x12/0x20
[Sat Feb 21 18:53:48 2026] pci_stop_bus_device+0x6a/0x90
[Sat Feb 21 18:53:48 2026] pci_stop_and_remove_bus_device+0x13/0x30
[Sat Feb 21 18:53:48 2026] mana_do_service+0x180/0x290 [mana]
[Sat Feb 21 18:53:48 2026] mana_serv_func+0x24/0x50 [mana]
[Sat Feb 21 18:53:48 2026] process_one_work+0x190/0x3d0
[Sat Feb 21 18:53:48 2026] worker_thread+0x16e/0x2e0
[Sat Feb 21 18:53:48 2026] kthread+0xf7/0x130
[Sat Feb 21 18:53:48 2026] ? __pfx_worker_thread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ? __pfx_kthread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ret_from_fork+0x269/0x350
[Sat Feb 21 18:53:48 2026] ? __pfx_kthread+0x10/0x10
[Sat Feb 21 18:53:48 2026] ret_from_fork_asm+0x1a/0x30
[Sat Feb 21 18:53:48 2026] </TASK>
Fixes: 505cc26bca ("net: mana: Add support for auxiliary device servicing events")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dipayaan Roy <dipayanroy@linux.microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/aZ2bzL64NagfyHpg@linuxonhyperv3.guj3yctzbm1etfxqx2vob5hsef.xx.internal.cloudapp.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bbd9900d ]
Ntuple filters can be deleted when the interface
is down. The current code blindly sends the filter
delete command to FW. When the interface is down, all
the VNICs are deleted in the FW. When the VNIC is
freed in the FW, all the associated filters are also
freed. We need not send the free command explicitly.
Sending such command will generate FW error in the
dmesg.
In order to fix this, we can safely return from
bnxt_hwrm_cfa_ntuple_filter_free() when BNXT_STATE_OPEN
is not true which confirms the VNICs have been deleted.
Fixes: 8336a974f3 ("bnxt_en: Save user configured filters in a lookup list")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260219185313.2682148-3-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e123d9302d ]
We need to free the corresponding RSS context VNIC
in FW everytime an RSS context is deleted in driver.
Commit 667ac333db added a check to delete the VNIC
in FW only when netif_running() is true to help delete
RSS contexts with interface down.
Having that condition will make the driver leak VNICs
in FW whenever close() happens with active RSS contexts.
On the subsequent open(), as part of RSS context restoration,
we will end up trying to create extra VNICs for which we
did not make any reservation. FW can fail this request,
thereby making us lose active RSS contexts.
Suppose an RSS context is deleted already and we try to
process a delete request again, then the HWRM functions
will check for validity of the request and they simply
return if the resource is already freed. So, even for
delete-when-down cases, netif_running() check is not
necessary.
Remove the netif_running() condition check when deleting
an RSS context.
Reported-by: Jakub Kicinski <kicinski@meta.com>
Fixes: 667ac333db ("eth: bnxt: allow deleting RSS contexts when the device is down")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20260219185313.2682148-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 594163ea88 ]
In ixp4xx_get_ts_info() ixp46x_ptp_find() is called
unconditionally despite this feature only existing on
ixp46x, leading to the following splat from tcpdump:
root@OpenWrt:~# tcpdump -vv -X -i eth0
(...)
Unable to handle kernel NULL pointer dereference at virtual address
00000238 when read
(...)
Call trace:
ptp_clock_index from ixp46x_ptp_find+0x1c/0x38
ixp46x_ptp_find from ixp4xx_get_ts_info+0x4c/0x64
ixp4xx_get_ts_info from __ethtool_get_ts_info+0x90/0x108
__ethtool_get_ts_info from __dev_ethtool+0xa00/0x2648
__dev_ethtool from dev_ethtool+0x160/0x234
dev_ethtool from dev_ioctl+0x2cc/0x460
dev_ioctl from sock_ioctl+0x1ec/0x524
sock_ioctl from sys_ioctl+0x51c/0xa94
sys_ioctl from ret_fast_syscall+0x0/0x44
(...)
Segmentation fault
Check for ixp46x in ixp46x_ptp_find() before trying to set up
PTP to avoid this.
To avoid altering the returned error code from ixp4xx_hwtstamp_set()
which before this patch was -EOPNOTSUPP, we return -EOPNOTSUPP
from ixp4xx_hwtstamp_set() if ixp46x_ptp_find() fails no matter
the error code. The helper function ixp46x_ptp_find() helper
returns -ENODEV.
Fixes: 9055a2f591 ("ixp4xx_eth: make ptp support a platform driver")
Signed-off-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20260219-ixp4xx-fix-ethernet-v3-1-f235ccc3cd46@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c17f4373d ]
In {tcp6,udp6,raw6}_sock, struct ipv6_pinfo is always placed at
the beginning of a new cache line because
1. __alignof__(struct tcp_sock) is 64 due to ____cacheline_aligned
of __cacheline_group_begin(tcp_sock_write_tx)
2. __alignof__(struct udp_sock) is 64 due to ____cacheline_aligned
of struct numa_drop_counters
3. in raw6_sock, struct numa_drop_counters is placed before
struct ipv6_pinfo
. struct ipv6_pinfo is 136 bytes, but the last cache line is
only used by ipv6_fl_list:
$ pahole -C ipv6_pinfo vmlinux
struct ipv6_pinfo {
...
/* --- cacheline 2 boundary (128 bytes) --- */
struct ipv6_fl_socklist * ipv6_fl_list; /* 128 8 */
/* size: 136, cachelines: 3, members: 23 */
Let's move ipv6_fl_list from struct ipv6_pinfo to struct inet_sock
to save a full cache line for {tcp6,udp6,raw6}_sock.
Now, struct ipv6_pinfo is 128 bytes, and {tcp6,udp6,raw6}_sock have
64 bytes less, while {tcp,udp,raw}_sock retain the same size.
Before:
# grep -E "^(RAW|UDP[^L\-]|TCP)" /proc/slabinfo | awk '{print $1, "\t", $4}'
RAWv6 1408
UDPv6 1472
TCPv6 2560
RAW 1152
UDP 1280
TCP 2368
After:
# grep -E "^(RAW|UDP[^L\-]|TCP)" /proc/slabinfo | awk '{print $1, "\t", $4}'
RAWv6 1344
UDPv6 1408
TCPv6 2496
RAW 1152
UDP 1280
TCP 2368
Also, ipv6_fl_list and inet_flags (SNDFLOW bit) are placed in the
same cache line.
$ pahole -C inet_sock vmlinux
...
/* --- cacheline 11 boundary (704 bytes) was 56 bytes ago --- */
struct ipv6_pinfo * pinet6; /* 760 8 */
/* --- cacheline 12 boundary (768 bytes) --- */
struct ipv6_fl_socklist * ipv6_fl_list; /* 768 8 */
unsigned long inet_flags; /* 776 8 */
Doc churn is due to the insufficient Type column (only 1 space short).
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251014224210.2964778-1-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 858d2a4f67 ("tcp: fix potential race in tcp_v6_syn_recv_sock()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd24173439 ]
While compile testing on less common architectures, I noticed that gcc-10 on
s390 finds a bug that all other configurations seem to miss:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c: In function 'myri10ge_set_multicast_list':
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:391:25: error: 'cmd.data0' is used uninitialized in this function [-Werror=uninitialized]
391 | buf->data0 = htonl(data->data0);
| ^~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:392:25: error: '*((void *)&cmd+4)' is used uninitialized in this function [-Werror=uninitialized]
392 | buf->data1 = htonl(data->data1);
| ^~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c: In function 'myri10ge_allocate_rings':
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:392:13: error: 'cmd.data1' is used uninitialized in this function [-Werror=uninitialized]
392 | buf->data1 = htonl(data->data1);
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:1939:22: note: 'cmd.data1' was declared here
1939 | struct myri10ge_cmd cmd;
| ^~~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:393:13: error: 'cmd.data2' is used uninitialized in this function [-Werror=uninitialized]
393 | buf->data2 = htonl(data->data2);
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:1939:22: note: 'cmd.data2' was declared here
1939 | struct myri10ge_cmd cmd;
It would be nice to understand how to make other compilers catch this as
well, but for the moment I'll just shut up the warning by fixing the
undefined behavior in this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260205162935.2126442-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61cef6454c ]
It appears that in commit 7efd79c0e6 ("bnxt_en: Add drop action
support for ntuple"), bnxt gained support for ntuple filters for packet
drops.
However, support for this does not seem to work in recent kernels or
against net-next:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
rmgr: Cannot insert RX class rule: Operation not supported
Cannot insert classification rule
The issue is that the existing code uses ethtool_get_flow_spec_ring_vf,
which will return a non-zero value if the ring_cookie is set to
RX_CLS_FLOW_DISC, which then causes bnxt_add_ntuple_cls_rule to return
-EOPNOTSUPP because it thinks the user is trying to set an ntuple filter
for a vf.
Fix this by first checking that the ring_cookie is not RX_CLS_FLOW_DISC.
After this patch, ntuple filters for drops can be added:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
Added rule with ID 0
% ethtool -n eth0
44 RX rings available
Total 1 rules
Filter: 0
Rule Type: UDP over IPv4
Src IP addr: 1.1.1.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
Action: Drop
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260131003042.2570434-1-joe@dama.to
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
