commit 3ddaa6a274 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e835c0a4e2 upstream.
Commit c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32b8f2b95 upstream.
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 734ae15ab9 upstream.
This reverts commit b138e23d3d.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3d ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4a944da707 ]
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to
be released, as already done in the other error handling path of the
probe.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd95da2cf ]
In the probe, some resources are allocated with
dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The
corresponding resources are already coorectly freed in the error handling
path of the probe, but not in the remove function.
Fix it.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 097fb3ee71 ]
Function dwc3_qcom_probe() allocates memory for resource structure
which is pointed by parent_res pointer. This memory is not
freed. This leads to memory leak. Use stack memory to prevent
memory leak.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c0aabed9ca upstream.
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some dwc3 glue drivers are currently accessing the driver data of the
child core device directly, which is clearly a bad idea as the child may
not have probed yet or may have been unbound from its driver.
As a workaround until the glue drivers have been fixed, clear the driver
data pointer before allowing the glue parent device to runtime suspend
to prevent its driver from accessing data that has been freed during
unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Message-ID: <20230607100540.31045-3-johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 glue driver is currently accessing the driver data of
the child core device during suspend and on wakeup interrupts. This is
clearly a bad idea as the child may not have probed yet or could have
been unbound from its driver.
The first such layering violation was part of the initial version of the
driver, but this was later made worse when the hack that accesses the
driver data of the grand child xhci device to configure the wakeup
interrupts was added.
Fixing this properly is not that easily done, so add a sanity check to
make sure that the child driver data is non-NULL before dereferencing it
for now.
Note that this relies on subtleties like the fact that driver core is
making sure that the parent is not suspended while the child is probing.
Reported-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/all/20230325165217.31069-4-manivannan.sadhasivam@linaro.org/
Fixes: d9152161b4 ("usb: dwc3: Add Qualcomm DWC3 glue layer driver")
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Cc: stable@vger.kernel.org # 3.18: a872ab303d: "usb: dwc3: qcom: fix use-after-free on runtime-PM wakeup"
Cc: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Message-ID: <20230607100540.31045-2-johan+linaro@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consider a scenario where cable disconnect happens when there is an active
usb reqest queued to the UDC. As part of the disconnect we would issue an
end transfer with no interrupt-on-completion before giving back this
request. Since we are giving back the request without skipping TRBs the
num_trbs field of dwc3_request still holds the stale value previously used.
Function drivers re-use same request for a given bind-unbind session and
hence their dwc3_request context gets preserved across cable
disconnect/connect. When such a request gets re-queued after cable connect,
we would increase the num_trbs field on top of the previous stale value
thus incorrectly representing the number of TRBs used. Fix this by
resetting num_trbs field before giving back the request.
Fixes: 09fe1f8d7e ("usb: dwc3: gadget: track number of TRBs per request")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was refactored recently and the "ret = " was accidentally deleted
so the errors aren't checked.
Fixes: 1d72fab476 ("USB: dwc3: refactor phy handling")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/d0c5a04f-deee-4ebe-9b0b-dc5492564519@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the dwc3 device is runtime suspended, various required clocks are in
disabled state and it is not guaranteed that access to any registers would
work. Depending on the SoC glue, a register read could be as benign as
returning 0 or be fatal enough to hang the system.
In order to prevent such scenarios of fatal errors, make sure to resume
dwc3 then allow the function to proceed.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org #3.2: 30332eeefe: debugfs: regset32: Add Runtime PM support
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230509144836.6803-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent -ETIMEDOUT error on .suspend().
e.g. If gadget driver is loaded and we are connected to a USB host,
all transfers must be stopped before stopping the controller else
we will not get a clean stop i.e. dwc3_gadget_run_stop() will take
several seconds to complete and will return -ETIMEDOUT.
Handle error cases properly in dwc3_gadget_suspend().
Simplify dwc3_gadget_resume() by using the introduced helper function.
Fixes: 9f8a67b65a ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable@vger.kernel.org
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230503110048.30617-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several sequences utilize the same routine for forcing the control endpoint
back into the SETUP phase. This is required, because those operations need
to ensure that EP0 is back in the default state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
Fixes: c96683798e ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230420212759.29429-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1
dwc3_gadget_ep_disable name=ep4in flags=1 direction=1
dwc3_gadget_ep_disable name=ep3out flags=1 direction=0
usb_gadget_disconnect deactivated=0 connected=0 ret=0
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3
spinlock as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable
path by re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
Fixes: c96683798e ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Cc: stable@vger.kernel.org
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20230413195742.11821-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the PARKMODE_DISABLE_HS bit in the DWC3_USB3_GUCTL1.
When this bit is set to '1' all HS bus instances in park mode are disabled
For some USB wifi devices, if enable this feature it will reduce the
performance. Therefore, add an option for disabling HS park mode by
device-tree.
In Synopsys's dwc3 data book:
In a few high speed devices when an IN request is sent within 900ns of the
ACK of the previous packet, these devices send a NAK. When connected to
these devices, if required, the software can disable the park mode if you
see performance drop in your system. When park mode is disabled,
pipelining of multiple packet is disabled and instead one packet at a time
is requested by the scheduler. This allows up to 12 NAKs in a micro-frame
and improves performance of these slow devices.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230419020044.15475-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the probe variable declarations by removing the stray newlines.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-12-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe callback has become unwieldy so break out the clock lookups
into a new helper function to improve readability.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-11-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the PHY handling using four new helpers to initialise,
deinitialise, power on and power off all the PHYs.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the core init error handling by using descriptive names for the
error labels and releasing resourcing in reverse order consistently.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While there likely are no platforms out there that mix generic and
legacy PHYs the driver should still be able to handle that, if only for
consistency reasons.
Add the missing calls to shutdown any legacy PHYs if generic PHY
initialisation fails.
Note that we continue to happily ignore potential errors from the legacy
PHY callbacks...
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.
Specifically, the scratch buffer DMA mapping would have been leaked on
every suspend cycle since commit 51f5d49ad6 ("usb: dwc3: core:
simplify suspend/resume operations") if this feature was ever enabled.
The related error handling was also broken and could have resulted in
attempts to unmap never mapped buffers, etc.
This effectively revert commit 0ffcaf3798 ("usb: dwc3: core: allocate
scratch buffers").
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.
Remove the hibernation bits from the gadget code, which effectively
reverts commits e1dadd3b0f ("usb: dwc3: workaround: bogus hibernation
events") and 7b2a0368bb ("usb: dwc3: gadget: set KEEP_CONNECT in case
of hibernation") except for the spurious interrupt warning.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing calls to disable autosuspend on probe errors and on
driver unbind.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to balance the runtime PM usage count on driver unbind by
adding back the pm_runtime_allow() call that had been erroneously
removed.
Fixes: 266d049390 ("usb: dwc3: core: don't trigger runtime pm when remove driver")
Cc: stable@vger.kernel.org # 5.9
Cc: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure not to suspend the device when probe fails to avoid disabling
clocks and phys multiple times.
Fixes: 328082376a ("usb: dwc3: fix runtime PM in error path")
Cc: stable@vger.kernel.org # 4.8
Cc: Roger Quadros <rogerq@ti.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several USB drivers use of_platform_* functions which are declared in
of_platform.h. of_platform.h gets implicitly included by of_device.h,
but that is going to be removed soon. Nothing else depends on of_device.h
so it can be dropped.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230410232639.1561152-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:
drivers/usb/dwc3/dwc3-pci.c
drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB host sends function suspend and function resume notifications to
the interface through SET_FEATURE/CLEAR_FEATURE setup packets.
Add support to handle these packets by delegating the requests to
composite layer. Also add support to handle function wake notification
requests to exit from function suspend state.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-5-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An usb device can initate a remote wakeup and bring the link out of
suspend as dictated by the DEVICE_REMOTE_WAKEUP feature selector.
Add support to handle this packet and set the remote wakeup capability.
Some hosts may take longer time to initiate the resume signaling after
device triggers a remote wakeup. So add async support to the wakeup API
by enabling link status change events.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-3-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly set and clear wakeup config so we don't leave anything
to chance.
Clear wakeup status on suspend so we know what caused wake up.
The LINESTATE wake up should not be enabled in device mode
if we are not connected to a USB host and in USB suspend (U2/L3)
else it will cause spurious wake up.
For now, don't enable LINESTATE. This means wake up from
USB resume will not work but at least we won't have any spurious
wake ups.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230324114429.21838-1-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the description of platform_get_irq()
* Return: non-zero IRQ number on success,
negative error number on failure.
and the code, platform_get_irq() will return -EINVAL
instead of IRQ0.
So platform_get_irq() no longer returns 0, there is no
need to check whether the return value is 0.
Found by Smatch:
drivers/usb/dwc3/host.c:60 dwc3_host_get_irq()
warn: platform_get_irq() does not return zero
Signed-off-by: Mingxuan Xiang <mx_xiang@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230324060934.1686859-1-mx_xiang@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes here, and the USB gadget update for future
development patches to be based on.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 5 missing register dump for debugfs as they are in use now.
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1679043328-13425-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB module can wakeup system. Enable it as a wakeup source
by default. Finer grain wakeup enable/disable can be done
from the power/wakeup system control file of the respective
USB device.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230316131226.89540-3-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB2SS IP in TI's AM62 SoC is capable of supporting wakeup from
deep sleep based on the following events,
1) VBUS state change
2) Overcurrent detection
3) Line state change
Wakeup from these events can enabled by setting their corresponding bits
in the WAKEUP_CONFIG register. The events to be enabled are decided based
on the current role of the controller.
When the role of the controller is host, the comparators for detecting
VBUS state change are disabled while entering low power mode. This is done
as VBUS state is not used in host mode and disabling the comparators helps
in reducing the power consumption. So, wakeup from VBUS state change should
be disabled in host mode. While operating in peripheral mode all the wakeup
events can be enabled.
Therefore, add support for the same in the suspend/resume hooks.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230316131226.89540-2-rogerq@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() only return non-zero irq number on success, or
negative error number on failure.
There is no need to check the return value of platform_get_irq()
to determine the return value of dwc3_gadget_get_irq(), removing
them to solve this problem.
Signed-off-by: Yalong Zou <yalongz@hust.edu.cn>
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230309150815.1884260-1-yalongz@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some __dynamic_array() buffer will only used at trace event output time,
change to __get_buf() which will allocate tempary trace seq buffer for
output purpose.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677465850-1396-4-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ULPI USB PHY does not support internal VBUS supply, to drive the CPEN
pin, which requires the configuration of the ULPI DRVVBUSEXTERNAL bit of
OTG_CTRL register.
Added 'snps,ulpi-ext-vbus-drv' a DT property to configure the USB2 PHY to
drive VBUS with an external supply, by setting the USB2 PHY ULPIEXTVBUSDRV
bit[:17] of the GUSB2PHYCFG register to drive VBUS with an external supply.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230215093146.5812-3-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_gpio.h provides a single function, which is not used in this driver.
Remove unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230215165239.83806-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
