commit 4b0768b655 upstream.
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Reported-by: Grant Grundler <grundler@chromium.org>
Tested-by: Grant Grundler <grundler@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ad722bd9e upstream.
The neighbour event callback call the function nfp_tun_write_neigh,
this function will take a mutex lock and it is in soft irq context,
change the work queue to process the neighbour event.
Move the nfp_tun_write_neigh function out of range rcu_read_lock/unlock()
in function nfp_tunnel_request_route_v4 and nfp_tunnel_request_route_v6.
Fixes: abc210952a ("nfp: flower: tunnel neigh support bond offload")
CC: stable@vger.kernel.org # 6.2+
Signed-off-by: Hui Zhou <hui.zhou@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1499b89289 ]
Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.
When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.
This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8
Fixes: ab32f56a41 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c7ed1f919 ]
In 4a56212774, USXGMII support was added for 6393X, but this was
lost in the PCS conversion (the blamed commit), most likely because
these efforts where more or less done in parallel.
Restore this feature by porting Michal's patch to fit the new
implementation.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Michal Smulski <michal.smulski@ooma.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: e5b732a275 ("net: dsa: mv88e6xxx: convert 88e639x to phylink_pcs")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20231205221359.3926018-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7336fc1967 ]
On new silicons the TX channels for transmit level has increased.
This patch fixes the respective register offset range to
configure the newly added channels.
Fixes: b279bbb331 ("octeontx2-af: NIX Tx scheduler queue config support")
Signed-off-by: Rahul Bhansali <rbhansali@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d431abd0a9 ]
If mcs resources are attached to PF/VF. These resources need
to be freed on FLR. This patch add missing mcs flr call on PF FLR.
Fixes: bd69476e86 ("octeontx2-af: cn10k: mcs: Install a default TCAM for normal traffic")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9723b2cca1 ]
On latest silicon versions SA cam entries increased to 256.
This patch fixes the datatype of sa_entries in mcs_hw_info
struct to u16 to hold 256 entries.
Fixes: 080bbd19c9 ("octeontx2-af: cn10k: mcs: Add mailboxes for port related operations")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dca6fa8644 ]
When MCS external bypass is disabled, MCS returns additional
2 credits(32B) for every packet Tx'ed on LMAC. To account for
these extra credits, NIX_AF_TX_LINKX_NORM_CREDIT.CC_MCS_CNT
needs to be configured as otherwise NIX Tx credits would overflow
and will never be returned to idle state credit count
causing issues with credit control and MTU change.
This patch fixes the same by configuring CC_MCS_CNT at probe
time for MCS enabled SoC's
Fixes: bd69476e86 ("octeontx2-af: cn10k: mcs: Install a default TCAM for normal traffic")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f708aba40f ]
If a xge port just connect with an optical module and no fiber,
it may have a fake link up because there may be interference on
the hardware. This patch adds an anti-shake to avoid the problem.
And the time of anti-shake is base on tests.
Fixes: b917078c1c ("net: hns: Add ACPI support to check SFP present")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84757d0839 ]
Upon changing the tx feature, the hns driver will modify the
maybe_stop_tx() and fill_desc() functions, if the modify happens
during packet sending, will cause the hardware and software
pointers do not match, and the port can not work anymore.
This patch deletes the maybe_stop_tx() and fill_desc() functions
modification when setting tx feature, and use the skb_is_gro()
to determine which functions to use in the tx path.
Fixes: 38f616da1c ("net:hns: Add support of ethtool TSO set option for Hip06 in HNS")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe860be36 ]
If is_ptp_ring == true in the loop of __aq_ring_xdp_clean function,
then a timestamp is stored from a packet in a field of skb object,
which is not allocated at the moment of the call (skb == NULL).
Generalize aq_ptp_extract_ts and other affected functions so they don't
work with struct sk_buff*, but with struct skb_shared_hwtstamps*.
Found by Linux Verification Center (linuxtesting.org) with SVACE
Fixes: 26efaef759 ("net: atlantic: Implement xdp data plane")
Signed-off-by: Daniil Maximov <daniil31415it@gmail.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20231204085810.1681386-1-daniil31415it@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4115ba677c ]
Currently ionic_dim_work() is incorrect when in
split interrupt mode. This is because the interrupt
rate is only being changed for the Rx side even for
dim running on Tx. Fix this by using the qcq from
the container_of macro. Also, introduce some local
variables for a bit of cleanup.
Fixes: a6ff85e0a2 ("ionic: remove intr coalesce update from napi")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-3-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ceb3860a6 ]
Our friendly kernel test robot has reminded us that with a new
check we have a warning about a potential string truncation.
In this case it really doesn't hurt anything, but it is worth
addressing especially since there really is no reason to reserve
so many bytes for our queue names. It seems that cutting the
queue name buffer length in half stops the complaint.
Fixes: c06107cabe ("ionic: more ionic name tweaks")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311300201.lO8v7mKU-lkp@intel.com/
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231204192234.21017-2-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d007caaaf0 ]
When flow_indr_dev_register() fails, bnxt_init_tc will free
bp->tc_info through kfree(). However, the caller function
bnxt_init_one() will ignore this failure and call
bnxt_shutdown_tc() on failure of bnxt_dl_register(), where
a use-after-free happens. Fix this issue by setting
bp->tc_info to NULL after kfree().
Fixes: 627c89d00f ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://lore.kernel.org/r/20231204024004.8245-1-dinghao.liu@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a206d9959f ]
In __iavf_set_coalesce, the driver checks both ec->rx_coalesce_usecs and
ec->tx_coalesce_usecs for validity. It does this via a chain if if/else-if
blocks. If every single branch of the series of if statements exited, this
would be fine. However, the rx_coalesce_usecs is checked against zero to
print an informative message if use_adaptive_rx_coalesce is enabled. If
this check is true, it short circuits the entire chain of statements,
preventing validation of the tx_coalesce_usecs field.
Indeed, since commit e792779e6b ("iavf: Prevent changing static ITR
values if adaptive moderation is on") the iavf driver actually rejects any
change to the tx_coalesce_usecs or rx_coalesce_usecs when
use_adaptive_tx_coalesce or use_adaptive_rx_coalesce is enabled, making
this checking a bit redundant.
Fix this error by removing the unnecessary and redundant checks for
use_adaptive_rx_coalesce and use_adaptive_tx_coalesce. Since zero is a
valid value, and since the tx_coalesce_usecs and rx_coalesce_usecs fields
are already unsigned, remove the minimum value check. This allows assigning
an ITR value ranging from 0-8160 as described by the printed message.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d9f22b3d3 ]
Commit 3a2c6ced90 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:
<code>
...
/* if FDIR VSI was set up, start it now */
for (i = 0; i < pf->num_alloc_vsi; i++) {
if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
i40e_vsi_open(pf->vsi[i]);
break;
}
}
...
</code>
So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.
Fix the message by using 'pf->hw.port' for the port number.
Fixes: 3a2c6ced90 ("i40e: Add a check to see if MFS is set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e7f0087b0 ]
Fix setting dis_rx_filtering depending on whether port vlan is being
turned on or off. This was originally fixed in commit c793f8ea15 ("ice:
Fix disabling Rx VLAN filtering with port VLAN enabled"), but while
refactoring ice_vf_vsi_init_vlan_ops(), the fix has been lost. Restore the
fix along with the original comment from that change.
Also delete duplicate lines in ice_port_vlan_on().
Fixes: 2946204b3f ("ice: implement bridge port vlan")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c91c909f1 ]
The rvu_dl will be freed in rvu_npa_health_reporters_destroy(rvu_dl)
after the create_workqueue fails, and after that free, the rvu_dl will
be translate back through rvu_npa_health_reporters_create,
rvu_health_reporters_create, and rvu_register_dl. Finally it goes to the
err_dl_health label, being freed again in
rvu_health_reporters_destroy(rvu) by rvu_npa_health_reporters_destroy.
In the second calls of rvu_npa_health_reporters_destroy, however,
it uses rvu_dl->rvu_npa_health_reporter, which is already freed at
the end of rvu_npa_health_reporters_destroy in the first call.
So this patch prevents the first destroy by instantly returning -ENONMEN
when create_workqueue fails. In addition, since the failure of
create_workqueue is the only entrence of label err, it has been
integrated into the error-handling path of create_workqueue.
Fixes: f1168d1e20 ("octeontx2-af: Add devlink health reporters for NPA")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Link: https://lore.kernel.org/r/20231202095902.3264863-1-alexious@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37e4b8df27 ]
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adbf100fc4 ]
The current adaptive interrupt coalescing code updates only rx
packet stats for dim algorithm. This patch also updates tx packet
stats which will be useful when there is only tx traffic.
Also moved configuring hardware adaptive interrupt setting to
driver dim callback.
Fixes: 6e144b47f5 ("octeontx2-pf: Add support for adaptive interrupt coalescing")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231201053330.3903694-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b17a597fc ]
Probe of Sohard Arcnet cards fails,
if 2 or more cards are installed in a system.
See kernel log:
[ 2.759203] arcnet: arcnet loaded
[ 2.763648] arcnet:com20020: COM20020 chipset support (by David Woodhouse et al.)
[ 2.770585] arcnet:com20020_pci: COM20020 PCI support
[ 2.772295] com20020 0000:02:00.0: enabling device (0000 -> 0003)
[ 2.772354] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.071301] com20020 0000:02:00.0 arc0-0 (uninitialized): PCI COM20020: station FFh found at F080h, IRQ 101.
[ 3.071305] com20020 0000:02:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.071534] com20020 0000:07:00.0: enabling device (0000 -> 0003)
[ 3.071581] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.369501] com20020 0000:07:00.0: Led pci:green:tx:0-0 renamed to pci:green:tx:0-0_1 due to name collision
[ 3.369535] com20020 0000:07:00.0: Led pci:red:recon:0-0 renamed to pci:red:recon:0-0_1 due to name collision
[ 3.370586] com20020 0000:07:00.0 arc0-0 (uninitialized): PCI COM20020: station E1h found at C000h, IRQ 35.
[ 3.370589] com20020 0000:07:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.370608] com20020: probe of 0000:07:00.0 failed with error -5
commit 5ef216c1f8 ("arcnet: com20020-pci: add rotary index support")
changes the device name of all COM20020 based PCI cards,
even if only some cards support this:
snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
The error happens because all Sohard Arcnet cards would be called arc0-0,
since the Sohard Arcnet cards don't have a PLX rotary coder.
I.e. EAE Arcnet cards have a PLX rotary coder,
which sets the first decimal, ensuring unique devices names.
This patch adds two new card feature flags to indicate
which cards support LEDs and the PLX rotary coder.
For EAE based cards the names still depend on the PLX rotary coder
(untested, since missing EAE hardware).
For Sohard based cards, this patch will result in devices
being called arc0, arc1, ... (tested).
Signed-off-by: Thomas Reichinger <thomas.reichinger@sohard.de>
Fixes: 5ef216c1f8 ("arcnet: com20020-pci: add rotary index support")
Link: https://lore.kernel.org/r/20231130113503.6812-1-thomas.reichinger@sohard.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79321a7939 ]
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_aldps_en().
Fixes: 4214cc550b ("r8152: check if disabling ALDPS is finished")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c53a7bd70 ]
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in r8153_pre_firmware_1().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a67b47fce ]
Delay loops in r8152 should break out if RTL8152_INACCESSIBLE is set
so that they don't delay too long if the device becomes
inaccessible. Add the break to the loop in
r8156b_wait_loading_flash().
Fixes: 195aae321c ("r8152: support new chips")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32a574c7e2 ]
Previous commits added checks for RTL8152_INACCESSIBLE in the loops in
the driver. There are still a few more that keep tripping the driver
up in error cases and make things take longer than they should. Add
those in.
All the loops that are part of this commit existed in some form or
another since the r8152 driver was first introduced, though
RTL8152_INACCESSIBLE was known as RTL8152_UNPLUG before commit
715f67f33a ("r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e62adaeecd ]
As of commit d9962b0d42 ("r8152: Block future register access if
register access fails") there is a race condition that can happen
between the USB device reset thread and napi_enable() (not) getting
called during rtl8152_open(). Specifically:
* While rtl8152_open() is running we get a register access error
that's _not_ -ENODEV and queue up a USB reset.
* rtl8152_open() exits before calling napi_enable() due to any reason
(including usb_submit_urb() returning an error).
In that case:
* Since the USB reset is perform in a separate thread asynchronously,
it can run at anytime USB device lock is not held - even before
rtl8152_open() has exited with an error and caused __dev_open() to
clear the __LINK_STATE_START bit.
* The rtl8152_pre_reset() will notice that the netif_running() returns
true (since __LINK_STATE_START wasn't cleared) so it won't exit
early.
* rtl8152_pre_reset() will then hang in napi_disable() because
napi_enable() was never called.
We can fix the race by making sure that the r8152 reset routines don't
run at the same time as we're opening the device. Specifically we need
the reset routines in their entirety rely on the return value of
netif_running(). The only way to reliably depend on that is for them
to hold the rntl_lock() mutex for the duration of reset.
Grabbing the rntl_lock() mutex for the duration of reset seems like a
long time, but reset is not expected to be common and the rtnl_lock()
mutex is already held for long durations since the core grabs it
around the open/close calls.
Fixes: d9962b0d42 ("r8152: Block future register access if register access fails")
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c89f49964 ]
rndis_filter uses utf8s_to_utf16s() which is provided by setting
NLS, so select NLS to fix the build error:
ERROR: modpost: "utf8s_to_utf16s" [drivers/net/hyperv/hv_netvsc.ko] undefined!
Fixes: 1ce09e899d ("hyperv: Add support for setting MAC from within guests")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20231130055853.19069-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 830139e7b6 ]
If a NIXLF is not attached to a PF/VF device then
nix_get_nixlf function fails and returns proper error
code. But npc_get_default_entry_action does not check it
and uses garbage value in subsequent calls. Fix this
by cheking the return value of nix_get_nixlf.
Fixes: 967db3529e ("octeontx2-af: add support for multicast/promisc packet replication feature")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9572c94938 ]
All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17dd5efe5f ]
tg3_tso_bug() drops a packet if it cannot be segmented for any reason.
The number of discarded frames should be incremented accordingly.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-2-alexey.pakhunov@spacex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 907d1bdb8b ]
This change moves [rt]x_dropped counters to tg3_napi so that they can be
updated by a single writer, race-free.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com>
Signed-off-by: Vincent Wong <vincent.wong2@spacex.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231113182350.37472-1-alexey.pakhunov@spacex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edf9bc396e ]
On RZ/G3S SMARC Carrier II board having RGMII connections b/w Ethernet
MACs and PHYs it has been discovered that doing unbind/bind for ravb
driver in a loop leads to wrong speed and duplex for Ethernet links and
broken connectivity (the connectivity cannot be restored even with
bringing interface down/up). Before doing unbind/bind the Ethernet
interfaces were configured though systemd. The sh instructions used to
do unbind/bind were:
$ cd /sys/bus/platform/drivers/ravb/
$ while :; do echo 11c30000.ethernet > unbind ; \
echo 11c30000.ethernet > bind; done
It has been discovered that there is a race b/w IOCTLs initialized by
systemd at the response of success binding and the
"ravb_write(ndev, CCC_OPC_RESET, CCC)" call in ravb_remove() as
follows:
1/ as a result of bind success the user space open/configures the
interfaces tough an IOCTL; the following stack trace has been
identified on RZ/G3S:
Call trace:
dump_backtrace+0x9c/0x100
show_stack+0x20/0x38
dump_stack_lvl+0x48/0x60
dump_stack+0x18/0x28
ravb_open+0x70/0xa58
__dev_open+0xf4/0x1e8
__dev_change_flags+0x198/0x218
dev_change_flags+0x2c/0x80
devinet_ioctl+0x640/0x708
inet_ioctl+0x1e4/0x200
sock_do_ioctl+0x50/0x108
sock_ioctl+0x240/0x358
__arm64_sys_ioctl+0xb0/0x100
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0xc0/0xc8
el0t_64_sync+0x190/0x198
2/ this call may execute concurrently with ravb_remove() as the
unbind/bind operation was executed in a loop
3/ if the operation mode is changed to RESET (through
ravb_write(ndev, CCC_OPC_RESET, CCC) call in ravb_remove())
while the above ravb_open() is in progress it may lead to MAC
(or PHY, or MAC-PHY connection, the right point hasn't been identified
at the moment) to be broken, thus the Ethernet connectivity fails to
restore.
The simple fix for this is to move ravb_write(ndev, CCC_OPC_RESET, CCC))
after unregister_netdev() to avoid resetting the controller while the
netdev interface is still registered.
To avoid future issues in ravb_remove(), the patch follows the proper order
of operations in ravb_remove(): reverse order compared with ravb_probe().
This avoids described races as the IOCTLs as well as unregister_netdev()
(called now at the beginning of ravb_remove()) calls rtnl_lock() before
continuing and IOCTLs check (though devinet_ioctl()) if device is still
registered just after taking the lock:
int devinet_ioctl(struct net *net, unsigned int cmd, struct ifreq *ifr)
{
// ...
rtnl_lock();
ret = -ENODEV;
dev = __dev_get_by_name(net, ifr->ifr_name);
if (!dev)
goto done;
// ...
done:
rtnl_unlock();
out:
return ret;
}
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac16a7334 ]
In case ravb_phy_start() returns with error the settings applied in
ravb_dmac_init() are not reverted (e.g. config mode). For this call
ravb_stop_dma() on failure path of ravb_open().
Fixes: a0d2f20650 ("Renesas Ethernet AVB PTP clock driver")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d78c0ced60 ]
Hardware manual of RZ/G3S (and RZ/G2L) specifies the following on the
description of CXR35 register (chapter "PHY interface select register
(CXR35)"): "After release reset, make write-access to this register before
making write-access to other registers (except MDIOMOD). Even if not need
to change the value of this register, make write-access to this register
at least one time. Because RGMII/MII MODE is recognized by accessing this
register".
The setup procedure for EMAC module (chapter "Setup procedure" of RZ/G3S,
RZ/G2L manuals) specifies the E-MAC.CXR35 register is the first EMAC
register that is to be configured.
Note [A] from chapter "PHY interface select register (CXR35)" specifies
the following:
[A] The case which CXR35 SEL_XMII is used for the selection of RGMII/MII
in APB Clock 100 MHz.
(1) To use RGMII interface, Set ‘H’03E8_0000’ to this register.
(2) To use MII interface, Set ‘H’03E8_0002’ to this register.
Take into account these indication.
Fixes: 1089877ada ("ravb: Add RZ/G2L MII interface support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88b74831fa ]
pm_runtime_get_sync() may return an error. In case it returns with an error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8eb6ea4b3 ]
reset_control_deassert() could return an error. Some devices cannot work
if reset signal de-assert operation fails. To avoid this check the return
code of reset_control_deassert() in ravb_probe() and take proper action.
Along with it, the free_netdev() call from the error path was moved after
reset_control_assert() on its own label (out_free_netdev) to free
netdev in case reset_control_deassert() fails.
Fixes: 0d13a1a464 ("ravb: Add reset support")
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f74a3dfcf ]
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9870257a0a ]
Fix races between ravb_tx_timeout_work() and functions of net_device_ops
and ethtool_ops by using rtnl_trylock() and rtnl_unlock(). Note that
since ravb_close() is under the rtnl lock and calls cancel_work_sync(),
ravb_tx_timeout_work() should calls rtnl_trylock(). Otherwise, a deadlock
may happen in ravb_tx_timeout_work() like below:
CPU0 CPU1
ravb_tx_timeout()
schedule_work()
...
__dev_close_many()
// Under rtnl lock
ravb_close()
cancel_work_sync()
// Waiting
ravb_tx_timeout_work()
rtnl_lock()
// This is possible to cause a deadlock
If rtnl_trylock() fails, rescheduling the work with sleep for 1 msec.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231127122420.3706751-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d3d14997 ]
ndo_stop() is RTNL-protected by net core, and the worker function takes
RTNL as well. Therefore we will deadlock when trying to execute a
pending work synchronously. To fix this execute any pending work
asynchronously. This will do no harm because netif_running() is false
in ndo_stop(), and therefore the work function is effectively a no-op.
However we have to ensure that no task is running or pending after
rtl_remove_one(), therefore add a call to cancel_work_sync().
Fixes: abe5fc42f9 ("r8169: use RTNL to protect critical sections")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/12395867-1d17-4cac-aa7d-c691938fcddf@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd7f98b2e1 ]
TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.
Fixes: 68fbff68db ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51597219e0 ]
When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e54d628a27 ]
Commit aeb18dd076 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd076 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad31c629ca ]
A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.
The patch moves the break to the
beginning of the loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb1930f96 ]
The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.
This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.
Fixes: 50f826999a ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f422abe3f2 ]
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f1 ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a524eabcd7 ]
As of commit b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for
phylink_pcs") probing of a Marvell 88e6350 switch causes a NULL pointer
de-reference like this example:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in:
CPU: 0 PID: 8 Comm: kworker/u2:0 Not tainted 6.7.0-rc2-dirty #26
Hardware name: Marvell Armada 370/XP (Device Tree)
Workqueue: events_unbound deferred_probe_work_func
PC is at mv88e6xxx_port_setup+0x1c/0x44
LR is at dsa_port_devlink_setup+0x74/0x154
pc : [<c057ea24>] lr : [<c0819598>] psr: a0000013
sp : c184fce0 ip : c542b8f4 fp : 00000000
r10: 00000001 r9 : c542a540 r8 : c542bc00
r7 : c542b838 r6 : c5244580 r5 : 00000005 r4 : c5244580
r3 : 00000000 r2 : c542b840 r1 : 00000005 r0 : c1a02040
...
The Marvell 6350 switch has no SERDES interface and so has no
corresponding pcs_ops defined for it. But during probing a call is made
to mv88e6xxx_port_setup() which unconditionally expects pcs_ops to exist -
though the presence of the pcs_ops->pcs_init function is optional.
Modify code to check for pcs_ops first, before checking for and calling
pcs_ops->pcs_init. Modify checking and use of pcs_ops->pcs_teardown
which may potentially suffer the same problem.
Fixes: b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for phylink_pcs")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3f1a164c7 ]
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.
According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
