linux/arch/mips/Kconfig

3224 lines
81 KiB

License cleanup: add SPDX GPL-2.0 license identifier to files with no license Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-01 15:07:57 +01:00
MIPS: use the generic get_user_pages_fast code The mips code is mostly equivalent to the generic one, minus various bugfixes and an arch override for gup_fast_permitted. Note that this defines ARCH_HAS_PTE_SPECIAL for mips as mips has pte_special and pte_mkspecial implemented and used in the existing gup code. They are no-op stubs, though which makes me a little unsure if this is really right thing to do. Note that this also adds back a missing cpu_has_dc_aliases check for __get_user_pages_fast, which the old code was only doing for get_user_pages_fast. This clearly looks like an oversight, as any condition that makes get_user_pages_fast unsafe also applies to __get_user_pages_fast. [hch@lst.de: MIPS: don't select ARCH_HAS_PTE_SPECIAL] Link: http://lkml.kernel.org/r/20190701151818.32227-3-hch@lst.de Link: http://lkml.kernel.org/r/20190625143715.1689-5-hch@lst.de Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: David Miller <davem@davemloft.net> Cc: James Hogan <jhogan@kernel.org> Cc: Khalid Aziz <khalid.aziz@oracle.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Paul Burton <paul.burton@mips.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Rich Felker <dalias@libc.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-07-11 20:56:52 -07:00
MIPS: Workaround GCC __builtin_unreachable reordering bug Some versions of GCC for the MIPS architecture suffer from a bug which can lead to instructions from beyond an unreachable statement being incorrectly reordered into earlier branch delay slots if the unreachable statement is the only content of a case in a switch statement. This can lead to seemingly random behaviour, such as invalid memory accesses from incorrectly reordered loads or stores, and link failures on microMIPS builds. See this potential GCC fix for details: https://gcc.gnu.org/ml/gcc-patches/2015-09/msg00360.html Runtime problems resulting from this bug were initially observed using a maltasmvp_defconfig v4.4 kernel built using GCC 4.9.2 (from a Codescape SDK 2015.06-05 toolchain), with the result being an address exception taken after log messages about the L1 caches (during probe of the L2 cache): Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] VPE topology {2,2} total 4 Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes <AdEL exception here> This is early enough that the kernel exception vectors are not in use, so any further output depends upon the bootloader. This is reproducible in QEMU where no further output occurs - ie. the system hangs here. Given the nature of the bug it may potentially be hit with differing symptoms. The bug is known to affect GCC versions as recent as 7.3, and it is unclear whether GCC 8 fixed it or just happens not to encounter the bug in the testcase found at the link above due to differing optimizations. This bug can be worked around by placing a volatile asm statement, which GCC is prevented from reordering past, prior to the __builtin_unreachable call. That was actually done already for other reasons by commit 173a3efd3edb ("bug.h: work around GCC PR82365 in BUG()"), but creates problems for microMIPS builds due to the lack of a .insn directive. The microMIPS ISA allows for interlinking with regular MIPS32 code by repurposing bit 0 of the program counter as an ISA mode bit. To switch modes one changes the value of this bit in the PC. However typical branch instructions encode their offsets as multiples of 2-byte instruction halfwords, which means they cannot change ISA mode - this must be done using either an indirect branch (a jump-register in MIPS terminology) or a dedicated jalx instruction. In order to ensure that regular branches don't attempt to target code in a different ISA which they can't actually switch to, the linker will check that branch targets are code in the same ISA as the branch. Unfortunately our empty asm volatile statements don't qualify as code, and the link for microMIPS builds fails with errors such as: arch/mips/mm/dma-default.s:3265: Error: branch to a symbol in another ISA mode arch/mips/mm/dma-default.s:5027: Error: branch to a symbol in another ISA mode Resolve this by adding a .insn directive within the asm statement which declares that what comes next is code. This may or may not be true, since we don't really know what comes next, but as this code is in an unreachable path anyway that doesn't matter since we won't execute it. We do this in asm/compiler.h & select CONFIG_HAVE_ARCH_COMPILER_H in order to have this included by linux/compiler_types.h after linux/compiler-gcc.h. This will result in asm/compiler.h being included in all C compilations via the -include linux/compiler_types.h argument in c_flags, which should be harmless. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: 173a3efd3edb ("bug.h: work around GCC PR82365 in BUG()") Patchwork: https://patchwork.linux-mips.org/patch/20270/ Cc: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@linux-mips.org
2018-08-20 15:36:18 -07:00
MIPS: Tracing: Add function graph tracer support for MIPS The implementation of function graph tracer for MIPS is a little different from X86. in MIPS, gcc(with -pg) only transfer the caller's return address(at) and the _mcount's return address(ra) to us. For the kernel part without -mlong-calls: move at, ra jal _mcount For the module part with -mlong-calls: lui v1, hi16bit_of_mcount addiu v1, v1, low16bit_of_mcount move at, ra jal _mcount Without -mlong-calls, if the function is a leaf, it will not save the return address(ra): ffffffff80101298 <au1k_wait>: ffffffff80101298: 67bdfff0 daddiu sp,sp,-16 ffffffff8010129c: ffbe0008 sd s8,8(sp) ffffffff801012a0: 03a0f02d move s8,sp ffffffff801012a4: 03e0082d move at,ra ffffffff801012a8: 0c042930 jal ffffffff8010a4c0 <_mcount> ffffffff801012ac: 00020021 nop so, we can hijack it directly in _mcount, but if the function is non-leaf, the return address is saved in the stack. ffffffff80133030 <copy_process>: ffffffff80133030: 67bdff50 daddiu sp,sp,-176 ffffffff80133034: ffbe00a0 sd s8,160(sp) ffffffff80133038: 03a0f02d move s8,sp ffffffff8013303c: ffbf00a8 sd ra,168(sp) ffffffff80133040: ffb70098 sd s7,152(sp) ffffffff80133044: ffb60090 sd s6,144(sp) ffffffff80133048: ffb50088 sd s5,136(sp) ffffffff8013304c: ffb40080 sd s4,128(sp) ffffffff80133050: ffb30078 sd s3,120(sp) ffffffff80133054: ffb20070 sd s2,112(sp) ffffffff80133058: ffb10068 sd s1,104(sp) ffffffff8013305c: ffb00060 sd s0,96(sp) ffffffff80133060: 03e0082d move at,ra ffffffff80133064: 0c042930 jal ffffffff8010a4c0 <_mcount> ffffffff80133068: 00020021 nop but we can not get the exact stack address(which saved ra) directly in _mcount, we need to search the content of at register in the stack space or search the "s{d,w} ra, offset(sp)" instruction in the text. 'Cause we can not prove there is only a match in the stack space, so, we search the text instead. as we can see, if the first instruction above "move at, ra" is not a store instruction, there should be a leaf function, so we hijack the at register directly via putting &return_to_handler into it, otherwise, we search the "s{d,w} ra, offset(sp)" instruction to get the stack offset, and then the stack address. we use the above copy_process() as an example, we at last find "ffbf00a8", 0xa8 is the stack offset, we plus it with s8(fp), that is the stack address, we hijack the content via writing the &return_to_handler in. If with -mlong-calls, since there are two more instructions above "move at, ra", so, we can move the pointer to the position above "lui v1, hi16bit_of_mcount". Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Nicholas Mc Guire <der.herr@hofr.at> Cc: zhangfx@lemote.com Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: http://patchwork.linux-mips.org/patch/677/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-11-20 20:34:34 +08:00
2012-09-28 14:31:03 +09:30
printk/nmi: generic solution for safe printk in NMI printk() takes some locks and could not be used a safe way in NMI context. The chance of a deadlock is real especially when printing stacks from all CPUs. This particular problem has been addressed on x86 by the commit a9edc8809328 ("x86/nmi: Perform a safe NMI stack trace on all CPUs"). The patchset brings two big advantages. First, it makes the NMI backtraces safe on all architectures for free. Second, it makes all NMI messages almost safe on all architectures (the temporary buffer is limited. We still should keep the number of messages in NMI context at minimum). Note that there already are several messages printed in NMI context: WARN_ON(in_nmi()), BUG_ON(in_nmi()), anything being printed out from MCE handlers. These are not easy to avoid. This patch reuses most of the code and makes it generic. It is useful for all messages and architectures that support NMI. The alternative printk_func is set when entering and is reseted when leaving NMI context. It queues IRQ work to copy the messages into the main ring buffer in a safe context. __printk_nmi_flush() copies all available messages and reset the buffer. Then we could use a simple cmpxchg operations to get synchronized with writers. There is also used a spinlock to get synchronized with other flushers. We do not longer use seq_buf because it depends on external lock. It would be hard to make all supported operations safe for a lockless use. It would be confusing and error prone to make only some operations safe. The code is put into separate printk/nmi.c as suggested by Steven Rostedt. It needs a per-CPU buffer and is compiled only on architectures that call nmi_enter(). This is achieved by the new HAVE_NMI Kconfig flag. The are MN10300 and Xtensa architectures. We need to clean up NMI handling there first. Let's do it separately. The patch is heavily based on the draft from Peter Zijlstra, see https://lkml.org/lkml/2015/6/10/327 [arnd@arndb.de: printk-nmi: use %zu format string for size_t] [akpm@linux-foundation.org: min_t->min - all types are size_t here] Signed-off-by: Petr Mladek <pmladek@suse.com> Suggested-by: Peter Zijlstra <peterz@infradead.org> Suggested-by: Steven Rostedt <rostedt@goodmis.org> Cc: Jan Kara <jack@suse.cz> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> [arm part] Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Jiri Kosina <jkosina@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: David Miller <davem@davemloft.net> Cc: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-20 17:00:33 -07:00
[MIPS] R4000/R4400 errata workarounds This is the gereric part of R4000/R4400 errata workarounds. They include compiler and assembler support as well as some source code modifications to address the problems with some combinations of multiply/divide+shift instructions as well as the daddi and daddiu instructions. Changes included are as follows: 1. New Kconfig options to select workarounds by platforms as necessary. 2. Arch top-level Makefile to pass necessary options to the compiler; also incompatible configurations are detected (-mno-sym32 unsupported as horribly intrusive for little gain). 3. Bug detection updated and shuffled -- the multiply/divide+shift problem is lethal enough that if not worked around it makes the kernel crash in time_init() because of a division by zero; the daddiu erratum might also trigger early potentially, though I have not observed it. On the other hand the daddi detection code requires the exception subsystem to have been initialised (and is there mainly for information). 4. r4k_daddiu_bug() added so that the existence of the erratum can be queried by code at the run time as necessary; useful for generated code like TLB fault and copy/clear page handlers. 5. __udelay() updated as it uses multiplication in inline assembly. Note that -mdaddi requires modified toolchain (which has been maintained by myself and available from my site for ~4years now -- versions covered are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000 and -mfix-r4400 have been standard for a while though. Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-10-23 12:43:11 +01:00
MIPS: Fix undefined reference to physical_memsize Since commit d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") switched the default platform to the "generic" platform, allmodconfig has been failing with the following linker error (among other errors): arch/mips/kernel/vpe-mt.o In function `vpe_run': (.text+0x59c): undefined reference to `physical_memsize' The Lantiq platform already worked around the same issue in commit 9050d50e2244 ("MIPS: lantiq: Set physical_memsize") by declaring physical_memsize with the initial value of 0 (on the assumption that the actual memory size will be hard-coded in the loaded VPE firmware), and the Malta platform already provided physical_memsize. Since all other platforms will fail to link with the VPE loader enabled, only allow Lantiq and Malta platforms to enable it, by way of a SYS_SUPPORTS_VPE_LOADER which is selected by those two platforms and which MIPS_VPE_LOADER depends on. SYS_SUPPORTS_MULTITHREADING is now a dependency of SYS_SUPPORTS_VPE_LOADER so that Kconfig emits a warning if SYS_SUPPORTS_VPE_LOADER is selected without SYS_SUPPORTS_MULTITHREADING. Fixes: d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: John Crispin <john@phrozen.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@mips.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Patchwork: https://patchwork.linux-mips.org/patch/18453/
2018-01-15 20:54:35 +00:00
MIPS: Fix undefined reference to physical_memsize Since commit d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") switched the default platform to the "generic" platform, allmodconfig has been failing with the following linker error (among other errors): arch/mips/kernel/vpe-mt.o In function `vpe_run': (.text+0x59c): undefined reference to `physical_memsize' The Lantiq platform already worked around the same issue in commit 9050d50e2244 ("MIPS: lantiq: Set physical_memsize") by declaring physical_memsize with the initial value of 0 (on the assumption that the actual memory size will be hard-coded in the loaded VPE firmware), and the Malta platform already provided physical_memsize. Since all other platforms will fail to link with the VPE loader enabled, only allow Lantiq and Malta platforms to enable it, by way of a SYS_SUPPORTS_VPE_LOADER which is selected by those two platforms and which MIPS_VPE_LOADER depends on. SYS_SUPPORTS_MULTITHREADING is now a dependency of SYS_SUPPORTS_VPE_LOADER so that Kconfig emits a warning if SYS_SUPPORTS_VPE_LOADER is selected without SYS_SUPPORTS_MULTITHREADING. Fixes: d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: John Crispin <john@phrozen.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@mips.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Patchwork: https://patchwork.linux-mips.org/patch/18453/
2018-01-15 20:54:35 +00:00
MIPS: SiByte: Enable swiotlb for SWARM, LittleSur and BigSur The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip DRAM controller that supports memory amounts of up to 16GiB, and due to how the address decoder has been wired in the SOC any memory beyond 1GiB is actually mapped starting from 4GiB physical up, that is beyond the 32-bit addressable limit[1]. Consequently if the maximum amount of memory has been installed, then it will span up to 19GiB. Many of the evaluation boards we support that are based on one of these SOCs have their memory soldered and the amount present fits in the 32-bit address range. The BCM91250A SWARM board however has actual DIMM slots and accepts, depending on the peripherals revision of the SOC, up to 4GiB or 8GiB of memory in commercially available JEDEC modules[2]. I believe this is also the case with the BCM91250C2 LittleSur board. This means that up to either 3GiB or 7GiB of memory requires 64-bit addressing to access. I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead, accepts at least as much memory, although I have no documentation or actual hardware available to verify that. Both systems have PCI slots installed for use by any PCI option boards, including ones that only support 32-bit addressing (additionally the 32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits addressing to 32-bits), and there is no IOMMU available. Therefore for PCI DMA to work in the presence of memory beyond enable swiotlb for the affected systems. All the other SOC onchip DMA devices use 40-bit addressing and therefore can address the whole memory, so only enable swiotlb if PCI support and support for DMA beyond 4GiB have been both enabled in the configuration of the kernel. This shows up as follows: Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2) Board type: SiByte BCM91250A (SWARM) Determined physical RAM map: memory: 000000000fe7fe00 @ 0000000000000000 (usable) memory: 000000001ffffe00 @ 0000000080000000 (usable) memory: 000000000ffffe00 @ 00000000c0000000 (usable) memory: 0000000087fffe00 @ 0000000100000000 (usable) software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB) in the bootstrap log and removes failures like these: defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi0: Receive buffer allocation failed fddi0: Adapter open failed! IP-Config: Failed to open fddi0 defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi1: Receive buffer allocation failed fddi1: Adapter open failed! IP-Config: Failed to open fddi1 when memory beyond 4GiB is handed out to devices that can only do 32-bit addressing. This updates commit cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32."). References: [1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R, Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview", "Memory Map", pp. 34-38 [2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom Corporation, 18 May 2004, Section 3: "Physical Description", "Supported DRAM", p. 23 Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> [paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it] Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/21108/ References: cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
2018-11-13 22:42:44 +00:00
MIPS: SiByte: Enable swiotlb for SWARM, LittleSur and BigSur The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip DRAM controller that supports memory amounts of up to 16GiB, and due to how the address decoder has been wired in the SOC any memory beyond 1GiB is actually mapped starting from 4GiB physical up, that is beyond the 32-bit addressable limit[1]. Consequently if the maximum amount of memory has been installed, then it will span up to 19GiB. Many of the evaluation boards we support that are based on one of these SOCs have their memory soldered and the amount present fits in the 32-bit address range. The BCM91250A SWARM board however has actual DIMM slots and accepts, depending on the peripherals revision of the SOC, up to 4GiB or 8GiB of memory in commercially available JEDEC modules[2]. I believe this is also the case with the BCM91250C2 LittleSur board. This means that up to either 3GiB or 7GiB of memory requires 64-bit addressing to access. I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead, accepts at least as much memory, although I have no documentation or actual hardware available to verify that. Both systems have PCI slots installed for use by any PCI option boards, including ones that only support 32-bit addressing (additionally the 32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits addressing to 32-bits), and there is no IOMMU available. Therefore for PCI DMA to work in the presence of memory beyond enable swiotlb for the affected systems. All the other SOC onchip DMA devices use 40-bit addressing and therefore can address the whole memory, so only enable swiotlb if PCI support and support for DMA beyond 4GiB have been both enabled in the configuration of the kernel. This shows up as follows: Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2) Board type: SiByte BCM91250A (SWARM) Determined physical RAM map: memory: 000000000fe7fe00 @ 0000000000000000 (usable) memory: 000000001ffffe00 @ 0000000080000000 (usable) memory: 000000000ffffe00 @ 00000000c0000000 (usable) memory: 0000000087fffe00 @ 0000000100000000 (usable) software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB) in the bootstrap log and removes failures like these: defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi0: Receive buffer allocation failed fddi0: Adapter open failed! IP-Config: Failed to open fddi0 defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi1: Receive buffer allocation failed fddi1: Adapter open failed! IP-Config: Failed to open fddi1 when memory beyond 4GiB is handed out to devices that can only do 32-bit addressing. This updates commit cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32."). References: [1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R, Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview", "Memory Map", pp. 34-38 [2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom Corporation, 18 May 2004, Section 3: "Physical Description", "Supported DRAM", p. 23 Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> [paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it] Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/21108/ References: cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
2018-11-13 22:42:44 +00:00
MIPS: SiByte: Enable swiotlb for SWARM, LittleSur and BigSur The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip DRAM controller that supports memory amounts of up to 16GiB, and due to how the address decoder has been wired in the SOC any memory beyond 1GiB is actually mapped starting from 4GiB physical up, that is beyond the 32-bit addressable limit[1]. Consequently if the maximum amount of memory has been installed, then it will span up to 19GiB. Many of the evaluation boards we support that are based on one of these SOCs have their memory soldered and the amount present fits in the 32-bit address range. The BCM91250A SWARM board however has actual DIMM slots and accepts, depending on the peripherals revision of the SOC, up to 4GiB or 8GiB of memory in commercially available JEDEC modules[2]. I believe this is also the case with the BCM91250C2 LittleSur board. This means that up to either 3GiB or 7GiB of memory requires 64-bit addressing to access. I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead, accepts at least as much memory, although I have no documentation or actual hardware available to verify that. Both systems have PCI slots installed for use by any PCI option boards, including ones that only support 32-bit addressing (additionally the 32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits addressing to 32-bits), and there is no IOMMU available. Therefore for PCI DMA to work in the presence of memory beyond enable swiotlb for the affected systems. All the other SOC onchip DMA devices use 40-bit addressing and therefore can address the whole memory, so only enable swiotlb if PCI support and support for DMA beyond 4GiB have been both enabled in the configuration of the kernel. This shows up as follows: Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2) Board type: SiByte BCM91250A (SWARM) Determined physical RAM map: memory: 000000000fe7fe00 @ 0000000000000000 (usable) memory: 000000001ffffe00 @ 0000000080000000 (usable) memory: 000000000ffffe00 @ 00000000c0000000 (usable) memory: 0000000087fffe00 @ 0000000100000000 (usable) software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB) in the bootstrap log and removes failures like these: defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi0: Receive buffer allocation failed fddi0: Adapter open failed! IP-Config: Failed to open fddi0 defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0 fddi1: Receive buffer allocation failed fddi1: Adapter open failed! IP-Config: Failed to open fddi1 when memory beyond 4GiB is handed out to devices that can only do 32-bit addressing. This updates commit cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32."). References: [1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R, Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview", "Memory Map", pp. 34-38 [2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom Corporation, 18 May 2004, Section 3: "Physical Description", "Supported DRAM", p. 23 Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> [paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it] Signed-off-by: Paul Burton <paul.burton@mips.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Patchwork: https://patchwork.linux-mips.org/patch/21108/ References: cce335ae47e2 ("[MIPS] 64-bit Sibyte kernels need DMA32.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
2018-11-13 22:42:44 +00:00
EDAC: Cleanup atomic_scrub mess So first of all, this atomic_scrub() function's naming is bad. It looks like an atomic_t helper. Change it to edac_atomic_scrub(). The bigger problem is that this function is arch-specific and every new arch which doesn't necessarily need that functionality still needs to define it, otherwise EDAC doesn't compile. So instead of doing that and including arch-specific headers, have each arch define an EDAC_ATOMIC_SCRUB symbol which can be used in edac_mc.c for ifdeffery. Much cleaner. And we already are doing this with another symbol - EDAC_SUPPORT. This is also much cleaner than having CONFIG_EDAC enumerate all the arches which need/have EDAC support and drivers. This way I can kill the useless edac.h header in tile too. Acked-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Chris Metcalf <cmetcalf@ezchip.com> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Doug Thompson <dougthompson@xmission.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-edac@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linuxppc-dev@lists.ozlabs.org Cc: "Maciej W. Rozycki" <macro@codesourcery.com> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Cc: Paul Mackerras <paulus@samba.org> Cc: "Steven J. Hill" <Steven.Hill@imgtec.com> Cc: x86@kernel.org Signed-off-by: Borislav Petkov <bp@suse.de>
2015-05-21 19:59:31 +02:00
MIPS: VDSO: Add implementations of gettimeofday() and clock_gettime() Add user-mode implementations of gettimeofday() and clock_gettime() to the VDSO. This is currently usable with 2 clocksources: the CP0 count register, which is accessible to user-mode via RDHWR on R2 and later cores, or the MIPS Global Interrupt Controller (GIC) timer, which provides a "user-mode visible" section containing a mirror of its counter registers. This section must be mapped into user memory, which is done below the VDSO data page. When a supported clocksource is not in use, the VDSO functions will return -ENOSYS, which causes libc to fall back on the standard syscall path. When support for neither of these clocksources is compiled into the kernel at all, the VDSO still provides clock_gettime(), as the coarse realtime/monotonic clocks can still be implemented. However, gettimeofday() is not provided in this case as nothing can be done without a suitable clocksource. This causes the symbol lookup to fail in libc and it will then always use the standard syscall path. This patch includes a workaround for a bug in QEMU which results in RDHWR on the CP0 count register always returning a constant (incorrect) value. A fix for this has been submitted, and the workaround can be removed after the fix has been in stable releases for a reasonable amount of time. A simple performance test which calls gettimeofday() 1000 times in a loop and calculates the average execution time gives the following results on a Malta + I6400 (running at 20MHz): - Syscall: ~31000 ns - VDSO (GIC): ~15000 ns - VDSO (CP0): ~9500 ns [markos.chandras@imgtec.com: - Minor code re-arrangements in order for mappings to be made in the order they appear to the process' address space. - Move do_{monotonic, realtime} outside of the MIPS_CLOCK_VSYSCALL ifdef - Use gic_get_usm_range so we can do the GIC mapping in the arch/mips/kernel/vdso instead of the GIC irqchip driver] Signed-off-by: Alex Smith <alex.smith@imgtec.com> Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11338/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-10-21 09:57:44 +01:00
MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT New Loongson 3 CPU (since Loongson-3A R2, as opposed to Loongson-3A R1, Loongson-3B R1 and Loongson-3B R2) has many enhancements, such as FTLB, L1-VCache, EI/DI/Wait/Prefetch instruction, DSP/DSPv2 ASE, User Local register, Read-Inhibit/Execute-Inhibit, SFB (Store Fill Buffer), Fast TLB refill support, etc. This patch introduce a config option, CONFIG_LOONGSON3_ENHANCEMENT, to enable those enhancements which are not probed at run time. If you want a generic kernel to run on all Loongson 3 machines, please say 'N' here. If you want a high-performance kernel to run on new Loongson 3 machines only, please say 'Y' here. Some additional explanations: 1) SFB locates between core and L1 cache, it causes memory access out of order, so writel/outl (and other similar functions) need a I/O reorder barrier. 2) Loongson 3 has a bug that di instruction can not save the irqflag, so arch_local_irq_save() is modified. Since CPU_MIPSR2 is selected by CONFIG_LOONGSON3_ENHANCEMENT, generic kernel doesn't use ei/di at all. 3) CPU_HAS_PREFETCH is selected by CONFIG_LOONGSON3_ENHANCEMENT, so MIPS_CPU_PREFETCH (used by uasm) probing is also put in this patch. Signed-off-by: Huacai Chen <chenhc@lemote.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: Steven J . Hill <sjhill@realitydiluted.com> Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/12755/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2016-03-03 09:45:13 +08:00
MIPS: Loongson: Introduce and use loongson_llsc_mb() On the Loongson-2G/2H/3A/3B there is a hardware flaw that ll/sc and lld/scd is very weak ordering. We should add sync instructions "before each ll/lld" and "at the branch-target between ll/sc" to workaround. Otherwise, this flaw will cause deadlock occasionally (e.g. when doing heavy load test with LTP). Below is the explaination of CPU designer: "For Loongson 3 family, when a memory access instruction (load, store, or prefetch)'s executing occurs between the execution of LL and SC, the success or failure of SC is not predictable. Although programmer would not insert memory access instructions between LL and SC, the memory instructions before LL in program-order, may dynamically executed between the execution of LL/SC, so a memory fence (SYNC) is needed before LL/LLD to avoid this situation. Since Loongson-3A R2 (3A2000), we have improved our hardware design to handle this case. But we later deduce a rarely circumstance that some speculatively executed memory instructions due to branch misprediction between LL/SC still fall into the above case, so a memory fence (SYNC) at branch-target (if its target is not between LL/SC) is needed for Loongson 3A1000, 3B1500, 3A2000 and 3A3000. Our processor is continually evolving and we aim to to remove all these workaround-SYNCs around LL/SC for new-come processor." Here is an example: Both cpu1 and cpu2 simutaneously run atomic_add by 1 on same atomic var, this bug cause both 'sc' run by two cpus (in atomic_add) succeed at same time('sc' return 1), and the variable is only *added by 1*, sometimes, which is wrong and unacceptable(it should be added by 2). Why disable fix-loongson3-llsc in compiler? Because compiler fix will cause problems in kernel's __ex_table section. This patch fix all the cases in kernel, but: +. the fix at the end of futex_atomic_cmpxchg_inatomic is for branch-target of 'bne', there other cases which smp_mb__before_llsc() and smp_llsc_mb() fix the ll and branch-target coincidently such as atomic_sub_if_positive/ cmpxchg/xchg, just like this one. +. Loongson 3 does support CONFIG_EDAC_ATOMIC_SCRUB, so no need to touch edac.h +. local_ops and cmpxchg_local should not be affected by this bug since only the owner can write. +. mips_atomic_set for syscall.c is deprecated and rarely used, just let it go Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Huang Pei <huangpei@loongson.cn> [paul.burton@mips.com: - Simplify the addition of -mno-fix-loongson3-llsc to cflags, and add a comment describing why it's there. - Make loongson_llsc_mb() a no-op when CONFIG_CPU_LOONGSON3_WORKAROUNDS=n, rather than a compiler memory barrier. - Add a comment describing the bug & how loongson_llsc_mb() helps in asm/barrier.h.] Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: ambrosehua@gmail.com Cc: Steven J . Hill <Steven.Hill@cavium.com> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Cc: Li Xuefeng <lixuefeng@loongson.cn> Cc: Xu Chenghua <xuchenghua@loongson.cn>
2019-01-15 16:04:54 +08:00
MIPS: Don't select ARCH_HAS_SYNC_DMA_FOR_CPU when DMA is coherent Commit f263f2a2c682 ("MIPS: Compile post DMA flush only when needed") pushed the selection of ARCH_HAS_SYNC_DMA_FOR_CPU down to various SYS_HAS_CPU_* Kconfig entries corresponding to CPUs for which cpu_needs_post_dma_flush() might return true, but unfortunately missed the fact that some of these CPUs can be used in configurations with DMA_NONCOHERENT=n. When this is the case the kernel build does not include our definition of arch_sync_dma_for_cpu() from arch/mips/mm/dma-noncoherent.c and the build fails with a link error. One example of this problem is ip27_defconfig: kernel/dma/direct.o: In function `dma_direct_sync_single_for_cpu': direct.c:(.text+0x6c): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_sync_sg_for_cpu': direct.c:(.text+0x1f0): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_alloc': direct.c:(.text+0xc20): undefined reference to `arch_dma_alloc' kernel/dma/direct.o: In function `dma_direct_free': direct.c:(.text+0xc3c): undefined reference to `arch_dma_free' make[1]: *** [Makefile:1021: vmlinux] Error 1 make: *** [Makefile:152: sub-make] Error 2 Fix this by selecting ARCH_HAS_SYNC_DMA_FOR_CPU only when DMA_NONCOHERENT is also selected. The SYS_HAS_CPU_BMIPS5000 case is left as-is because systems with that CPU always select DMA_NONCOHERENT anyway. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f263f2a2c682 ("MIPS: Compile post DMA flush only when needed")
2019-02-04 13:52:58 -08:00
MIPS: Don't select ARCH_HAS_SYNC_DMA_FOR_CPU when DMA is coherent Commit f263f2a2c682 ("MIPS: Compile post DMA flush only when needed") pushed the selection of ARCH_HAS_SYNC_DMA_FOR_CPU down to various SYS_HAS_CPU_* Kconfig entries corresponding to CPUs for which cpu_needs_post_dma_flush() might return true, but unfortunately missed the fact that some of these CPUs can be used in configurations with DMA_NONCOHERENT=n. When this is the case the kernel build does not include our definition of arch_sync_dma_for_cpu() from arch/mips/mm/dma-noncoherent.c and the build fails with a link error. One example of this problem is ip27_defconfig: kernel/dma/direct.o: In function `dma_direct_sync_single_for_cpu': direct.c:(.text+0x6c): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_sync_sg_for_cpu': direct.c:(.text+0x1f0): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_alloc': direct.c:(.text+0xc20): undefined reference to `arch_dma_alloc' kernel/dma/direct.o: In function `dma_direct_free': direct.c:(.text+0xc3c): undefined reference to `arch_dma_free' make[1]: *** [Makefile:1021: vmlinux] Error 1 make: *** [Makefile:152: sub-make] Error 2 Fix this by selecting ARCH_HAS_SYNC_DMA_FOR_CPU only when DMA_NONCOHERENT is also selected. The SYS_HAS_CPU_BMIPS5000 case is left as-is because systems with that CPU always select DMA_NONCOHERENT anyway. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f263f2a2c682 ("MIPS: Compile post DMA flush only when needed")
2019-02-04 13:52:58 -08:00
MIPS: Don't select ARCH_HAS_SYNC_DMA_FOR_CPU when DMA is coherent Commit f263f2a2c682 ("MIPS: Compile post DMA flush only when needed") pushed the selection of ARCH_HAS_SYNC_DMA_FOR_CPU down to various SYS_HAS_CPU_* Kconfig entries corresponding to CPUs for which cpu_needs_post_dma_flush() might return true, but unfortunately missed the fact that some of these CPUs can be used in configurations with DMA_NONCOHERENT=n. When this is the case the kernel build does not include our definition of arch_sync_dma_for_cpu() from arch/mips/mm/dma-noncoherent.c and the build fails with a link error. One example of this problem is ip27_defconfig: kernel/dma/direct.o: In function `dma_direct_sync_single_for_cpu': direct.c:(.text+0x6c): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_sync_sg_for_cpu': direct.c:(.text+0x1f0): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_alloc': direct.c:(.text+0xc20): undefined reference to `arch_dma_alloc' kernel/dma/direct.o: In function `dma_direct_free': direct.c:(.text+0xc3c): undefined reference to `arch_dma_free' make[1]: *** [Makefile:1021: vmlinux] Error 1 make: *** [Makefile:152: sub-make] Error 2 Fix this by selecting ARCH_HAS_SYNC_DMA_FOR_CPU only when DMA_NONCOHERENT is also selected. The SYS_HAS_CPU_BMIPS5000 case is left as-is because systems with that CPU always select DMA_NONCOHERENT anyway. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f263f2a2c682 ("MIPS: Compile post DMA flush only when needed")
2019-02-04 13:52:58 -08:00
MIPS: Don't select ARCH_HAS_SYNC_DMA_FOR_CPU when DMA is coherent Commit f263f2a2c682 ("MIPS: Compile post DMA flush only when needed") pushed the selection of ARCH_HAS_SYNC_DMA_FOR_CPU down to various SYS_HAS_CPU_* Kconfig entries corresponding to CPUs for which cpu_needs_post_dma_flush() might return true, but unfortunately missed the fact that some of these CPUs can be used in configurations with DMA_NONCOHERENT=n. When this is the case the kernel build does not include our definition of arch_sync_dma_for_cpu() from arch/mips/mm/dma-noncoherent.c and the build fails with a link error. One example of this problem is ip27_defconfig: kernel/dma/direct.o: In function `dma_direct_sync_single_for_cpu': direct.c:(.text+0x6c): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_sync_sg_for_cpu': direct.c:(.text+0x1f0): undefined reference to `arch_sync_dma_for_cpu' kernel/dma/direct.o: In function `dma_direct_alloc': direct.c:(.text+0xc20): undefined reference to `arch_dma_alloc' kernel/dma/direct.o: In function `dma_direct_free': direct.c:(.text+0xc3c): undefined reference to `arch_dma_free' make[1]: *** [Makefile:1021: vmlinux] Error 1 make: *** [Makefile:152: sub-make] Error 2 Fix this by selecting ARCH_HAS_SYNC_DMA_FOR_CPU only when DMA_NONCOHERENT is also selected. The SYS_HAS_CPU_BMIPS5000 case is left as-is because systems with that CPU always select DMA_NONCOHERENT anyway. Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: f263f2a2c682 ("MIPS: Compile post DMA flush only when needed")
2019-02-04 13:52:58 -08:00
MIPS: Fix undefined reference to physical_memsize Since commit d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") switched the default platform to the "generic" platform, allmodconfig has been failing with the following linker error (among other errors): arch/mips/kernel/vpe-mt.o In function `vpe_run': (.text+0x59c): undefined reference to `physical_memsize' The Lantiq platform already worked around the same issue in commit 9050d50e2244 ("MIPS: lantiq: Set physical_memsize") by declaring physical_memsize with the initial value of 0 (on the assumption that the actual memory size will be hard-coded in the loaded VPE firmware), and the Malta platform already provided physical_memsize. Since all other platforms will fail to link with the VPE loader enabled, only allow Lantiq and Malta platforms to enable it, by way of a SYS_SUPPORTS_VPE_LOADER which is selected by those two platforms and which MIPS_VPE_LOADER depends on. SYS_SUPPORTS_MULTITHREADING is now a dependency of SYS_SUPPORTS_VPE_LOADER so that Kconfig emits a warning if SYS_SUPPORTS_VPE_LOADER is selected without SYS_SUPPORTS_MULTITHREADING. Fixes: d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: John Crispin <john@phrozen.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@mips.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Patchwork: https://patchwork.linux-mips.org/patch/18453/
2018-01-15 20:54:35 +00:00
MIPS: Fix undefined reference to physical_memsize Since commit d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") switched the default platform to the "generic" platform, allmodconfig has been failing with the following linker error (among other errors): arch/mips/kernel/vpe-mt.o In function `vpe_run': (.text+0x59c): undefined reference to `physical_memsize' The Lantiq platform already worked around the same issue in commit 9050d50e2244 ("MIPS: lantiq: Set physical_memsize") by declaring physical_memsize with the initial value of 0 (on the assumption that the actual memory size will be hard-coded in the loaded VPE firmware), and the Malta platform already provided physical_memsize. Since all other platforms will fail to link with the VPE loader enabled, only allow Lantiq and Malta platforms to enable it, by way of a SYS_SUPPORTS_VPE_LOADER which is selected by those two platforms and which MIPS_VPE_LOADER depends on. SYS_SUPPORTS_MULTITHREADING is now a dependency of SYS_SUPPORTS_VPE_LOADER so that Kconfig emits a warning if SYS_SUPPORTS_VPE_LOADER is selected without SYS_SUPPORTS_MULTITHREADING. Fixes: d41e6858ba58 ("MIPS: Kconfig: Set default MIPS system type as generic") Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: John Crispin <john@phrozen.org> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Paul Burton <paul.burton@mips.com> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Tested-by: Guenter Roeck <linux@roeck-us.net> Patchwork: https://patchwork.linux-mips.org/patch/18453/
2018-01-15 20:54:35 +00:00
2014-04-14 11:00:56 +01:00
2014-04-14 11:00:56 +01:00
[MIPS] R4000/R4400 errata workarounds This is the gereric part of R4000/R4400 errata workarounds. They include compiler and assembler support as well as some source code modifications to address the problems with some combinations of multiply/divide+shift instructions as well as the daddi and daddiu instructions. Changes included are as follows: 1. New Kconfig options to select workarounds by platforms as necessary. 2. Arch top-level Makefile to pass necessary options to the compiler; also incompatible configurations are detected (-mno-sym32 unsupported as horribly intrusive for little gain). 3. Bug detection updated and shuffled -- the multiply/divide+shift problem is lethal enough that if not worked around it makes the kernel crash in time_init() because of a division by zero; the daddiu erratum might also trigger early potentially, though I have not observed it. On the other hand the daddi detection code requires the exception subsystem to have been initialised (and is there mainly for information). 4. r4k_daddiu_bug() added so that the existence of the erratum can be queried by code at the run time as necessary; useful for generated code like TLB fault and copy/clear page handlers. 5. __udelay() updated as it uses multiplication in inline assembly. Note that -mdaddi requires modified toolchain (which has been maintained by myself and available from my site for ~4years now -- versions covered are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000 and -mfix-r4400 have been standard for a while though. Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2007-10-23 12:43:11 +01:00
[PATCH] Configurable NODES_SHIFT Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5 NODES_SHIFT values in the current git tree. But it looks a bit messy. SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has been changeable by config. Suitable node's number may be changed in the future even if it is other architecture. So, I wrote configurable node's number. This patch set defines just default value for each arch which needs multi nodes except ia64. But, it is easy to change to configurable if necessary. On ia64 the number of nodes can be already configured in generic ia64 and SN2 config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It would be simpler. See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2 Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Andi Kleen <ak@muc.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Richard Henderson <rth@twiddle.net> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Jack Steiner <steiner@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-10 22:53:53 -07:00
2015-09-09 15:38:55 -07:00
MIPS: mark O32+FP64 experimental for now Commit 597ce1723e0f "MIPS: Support for 64-bit FP with O32 binaries" introduced support for setting Status.FR=1 for O32 binaries with the EF_MIPS_FP64 ELF header flag set. Whilst this flag is currently supported by binutils it does introduce an ABI break within userland. Objects built with EF_MIPS_FP64 cannot be safely linked with those built without it since code in either object may assume behaviour specific to a value of FR. More recently there has been discussion around avoiding further fragmentation of the O32 ABI whilst still allowing the use of FR=1 and features such as MSA which depend upon it. Details of the plan to allow this are still being worked on, and whilst the kernel will need the ability to handle FR=1 with O32 tasks it is unclear what else it may need to provide to a userland which seeks to avoid another ABI break. In order to prevent the proliferation of userland which may rely upon the current EF_MIPS_FP64 behaviour this patch marks the kernel support for it experimental & disables it by default. Under current proposals it is likely that this support can simply be enabled again later, but possibly after the introduction of further interfaces with userland and support for the MIPS R5 UFR feature. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: Matthew Fortune <matthew.fortune@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Paul Burton <paul.burton@imgtec.com> Patchwork: https://patchwork.linux-mips.org/patch/6549/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2014-02-14 17:55:18 +00:00
ELF/MIPS build fix CONFIG_MIPS32_N32=y but CONFIG_BINFMT_ELF disabled results in the following linker errors: arch/mips/built-in.o: In function `elf_core_dump': binfmt_elfn32.c:(.text+0x23dbc): undefined reference to `elf_core_extra_phdrs' binfmt_elfn32.c:(.text+0x246e4): undefined reference to `elf_core_extra_data_size' binfmt_elfn32.c:(.text+0x248d0): undefined reference to `elf_core_write_extra_phdrs' binfmt_elfn32.c:(.text+0x24ac4): undefined reference to `elf_core_write_extra_data' CONFIG_MIPS32_O32=y but CONFIG_BINFMT_ELF disabled results in the following linker errors: arch/mips/built-in.o: In function `elf_core_dump': binfmt_elfo32.c:(.text+0x28a04): undefined reference to `elf_core_extra_phdrs' binfmt_elfo32.c:(.text+0x29330): undefined reference to `elf_core_extra_data_size' binfmt_elfo32.c:(.text+0x2951c): undefined reference to `elf_core_write_extra_phdrs' binfmt_elfo32.c:(.text+0x29710): undefined reference to `elf_core_write_extra_data' This is because binfmt_elfn32 and binfmt_elfo32 are using symbols from elfcore but for these configurations elfcore will not be built. Fixed by making elfcore selectable by a separate config symbol which unlike the current mechanism can also be used from other directories than kernel/, then having each flavor of ELF that relies on elfcore.o, select it in Kconfig, including CONFIG_MIPS32_N32 and CONFIG_MIPS32_O32 which fixes this issue. Link: http://lkml.kernel.org/r/20160520141705.GA1913@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-05-23 16:22:26 -07:00