The driver works well on i.MX31 powered boards with device description
taken from board device tree, the only change to add to the driver is
the missing OF device id, the affected list of included headers and
indentation in platform driver struct are beautified a little.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Freescale i.MX21 and i.MX31 SoCs contain a Random Number Generator
Accelerator module (RNGA), which is replaced by RNGB and RNGC modules
on later i.MX SoC series, the change adds a new compatible property
to describe the controller.
Since all versions of Freescale RNG modules are legacy, apparently
the documentation file has no more potential for further extensions,
nevertheless generalize it by removing explicit RNGC specifics.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a NEON-accelerated implementation of Speck128-XTS and Speck64-XTS
for ARM64. This is ported from the 32-bit version. It may be useful on
devices with 64-bit ARM CPUs that don't have the Cryptography
Extensions, so cannot do AES efficiently -- e.g. the Cortex-A53
processor on the Raspberry Pi 3.
It generally works the same way as the 32-bit version, but there are
some slight differences due to the different instructions, registers,
and syntax available in ARM64 vs. in ARM32. For example, in the 64-bit
version there are enough registers to hold the XTS tweaks for each
128-byte chunk, so they don't need to be saved on the stack.
Benchmarks on a Raspberry Pi 3 running a 64-bit kernel:
Algorithm Encryption Decryption
--------- ---------- ----------
Speck64/128-XTS (NEON) 92.2 MB/s 92.2 MB/s
Speck128/256-XTS (NEON) 75.0 MB/s 75.0 MB/s
Speck128/256-XTS (generic) 47.4 MB/s 35.6 MB/s
AES-128-XTS (NEON bit-sliced) 33.4 MB/s 29.6 MB/s
AES-256-XTS (NEON bit-sliced) 24.6 MB/s 21.7 MB/s
The code performs well on higher-end ARM64 processors as well, though
such processors tend to have the Crypto Extensions which make AES
preferred. For example, here are the same benchmarks run on a HiKey960
(with CPU affinity set for the A73 cores), with the Crypto Extensions
implementation of AES-256-XTS added:
Algorithm Encryption Decryption
--------- ----------- -----------
AES-256-XTS (Crypto Extensions) 1273.3 MB/s 1274.7 MB/s
Speck64/128-XTS (NEON) 359.8 MB/s 348.0 MB/s
Speck128/256-XTS (NEON) 292.5 MB/s 286.1 MB/s
Speck128/256-XTS (generic) 186.3 MB/s 181.8 MB/s
AES-128-XTS (NEON bit-sliced) 142.0 MB/s 124.3 MB/s
AES-256-XTS (NEON bit-sliced) 104.7 MB/s 91.1 MB/s
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
David Ahern says:
====================
net/ipv6: Address checks need to consider the L3 domain
IPv6 prohibits a local address from being used as a gateway for a route.
However, it is ok for the gateway to be a local address in a different L3
domain (e.g., VRF). This allows, for example, veth pairs to connect VRFs.
ip6_route_info_create calls ipv6_chk_addr_and_flags for gateway addresses
to determine if the address is a local one, but ipv6_chk_addr_and_flags
does not currently consider L3 domains. As a result routes can not be
added in one VRF with a nexthop that points to a local address in a
second VRF.
Resolve by comparing the l3mdev for the passed in device and requiring an
l3mdev match with the device containing an address. The intent of checking
for an address on the specified device versus any device in the domain is
mantained by a new argument to skip the check between the passed in device
and the device with the address.
Patch 1 moves the gateway validation from ip6_route_info_create into a
helper; the function is long enough and refactoring drops the indent
level.
Patch 2 adds a skip_dev_check argument to ipv6_chk_addr_and_flags to
allow a device to always be passed yet skip the device check when
looking at addresses and fixes up a few ipv6_chk_addr callers that
pass a NULL device.
Patch 3 adds l3mdev checks to ipv6_chk_addr_and_flags.
Patches 4 and 5 do some refactoring to the fib_tests script and then
patch 6 adds nexthop validation tests.
v4
- separated l3mdev check into a separate patch (patch 3 of this set)
as suggested by Kirill
- consolidated dev and ipv6_chk_addr_and_flags call into 1 if (Kirill)
- added a temp variable for gw type (Kirill)
v3
- set skip_dev_check in ipv6_chk_addr based on dev == NULL (per
comment from Ido)
v2
- handle 2 variations of route spec with sane error path
- add test cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add series of tests for valid and invalid nexthop specs for IPv6.
$ TEST=fib_nexthop_test ./fib_tests.sh
...
IPv6 nexthop tests
TEST: Directly connected nexthop, unicast address [ OK ]
TEST: Directly connected nexthop, unicast address with device [ OK ]
TEST: Gateway is linklocal address [ OK ]
TEST: Gateway is linklocal address, no device [ OK ]
TEST: Gateway can not be local unicast address [ OK ]
TEST: Gateway can not be local unicast address, with device [ OK ]
TEST: Gateway can not be a local linklocal address [ OK ]
TEST: Gateway can be local address in a VRF [ OK ]
TEST: Gateway can be local address in a VRF, with device [ OK ]
TEST: Gateway can be local linklocal address in a VRF [ OK ]
TEST: Redirect to VRF lookup [ OK ]
TEST: VRF route, gateway can be local address in default VRF [ OK ]
TEST: VRF route, gateway can not be a local address [ OK ]
TEST: VRF route, gateway can not be a local addr with device [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to run just a specific fib test by setting the TEST
environment variable.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 'ip -netns testns' with the alias IP. Shortens the line lengths
and makes running the commands manually a bit easier.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lookup the L3 master device for the passed in device. Only consider
addresses on netdev's with the same master device. If the device is
not enslaved or is NULL, then the l3mdev is NULL which means only
devices not enslaved (ie, in the default domain) are considered.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_chk_addr_and_flags determines if an address is a local address and
optionally if it is an address on a specific device. For example, it is
called by ip6_route_info_create to determine if a given gateway address
is a local address. The address check currently does not consider L3
domains and as a result does not allow a route to be added in one VRF
if the nexthop points to an address in a second VRF. e.g.,
$ ip route add 2001:db8:1::/64 vrf r2 via 2001:db8:102::23
Error: Invalid gateway address.
where 2001:db8:102::23 is an address on an interface in vrf r1.
ipv6_chk_addr_and_flags needs to allow callers to always pass in a device
with a separate argument to not limit the address to the specific device.
The device is used used to determine the L3 domain of interest.
To that end add an argument to skip the device check and update callers
to always pass a device where possible and use the new argument to mean
any address in the domain.
Update a handful of users of ipv6_chk_addr with a NULL dev argument. This
patch handles the change to these callers without adding the domain check.
ip6_validate_gw needs to handle 2 cases - one where the device is given
as part of the nexthop spec and the other where the device is resolved.
There is at least 1 VRF case where deferring the check to only after
the route lookup has resolved the device fails with an unintuitive error
"RTNETLINK answers: No route to host" as opposed to the preferred
"Error: Gateway can not be a local address." The 'no route to host'
error is because of the fallback to a full lookup. The check is done
twice to avoid this error.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move gateway validation code from ip6_route_info_create into
ip6_validate_gw. Code move plus adjustments to handle the potential
reset of dev and idev and to make checkpatch happy.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brad Mouring says:
====================
net: macb: Introduce phy-handle DT functionality
Consider the situation where a macb netdev is connected through
a phydev that sits on a mii bus other than the one provided to
this particular netdev. This situation is what this patchset aims
to accomplish through the existing phy-handle optional binding.
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is precisely the
situation this patchset aims to solve, so it makes sense to introduce
the functionality to this driver (where the physical layout discussed
was encountered).
The devicetree snippet would look something like this:
...
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
...
The work done to add the phy_node in the first place (dacdbb4dfc:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
v2: Reorganization of mii probe/init functions, suggested by Andrew Lunn
v3: Moved some of the bus init code back into init (erroneously moved to probe)
some style issues, and an unintialized variable warning addressed.
v4: Add Reviewed-by: tags
Skip fallback code if phy-handle phandle is found
v5: Cleanup formatting issues
Fix compile failure introduced in 1/4 "net: macb: Reorganize macb_mii
bringup"
Fix typo in "Documentation: macb: Document phy-handle binding"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the existence of the optional binding, directing to the
general ethernet document that describes this binding.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)
The devicetree snippet would look something like this:
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
The work done to add the phy_node in the first place (dacdbb4dfc:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.
This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet_mmap documentation had links to no longer existing web
sites; replace with other site which has similar example.
Support for packet mmap has been in mainline versions of libpcap
for several years.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:
iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);
but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654 ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.
Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default stop endpoint completion handler will give back cancelled
URBs, and clean, or move past those canceller TRBs on the ring.
This is not always the preferred action.
If the stop endpoint command issuer is waiting for a completion
skip the default handler and just call the completion.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_register_device() returns error pointers on error, never NULL.
The IS_ERR_OR_NULL() function returns either 1 or 0 so it means we
return 1 on error instead of a proper error code. The caller only
checks for zero vs non-zero so this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There is a huge number of broken device trees out there. Just
grepping through the tree for the use of IRQ_TYPE_NONE in conjunction
with the GIC is scary.
People just don't realise that IRQ_TYPE_NONE just doesn't exist, and
you just get whatever junk was there before. So let's make them aware
of the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When perf_group_dettach() is called on a group leader, it updates each
sibling's group_leader field to point to that sibling, effectively
upgrading each siblnig to a group leader. After perf_group_detach has
completed, the caller may free the leader event.
We only remove siblings from the group leader's sibling_list when the
leader has a non-empty group_node. This was fine prior to commit:
8343aae661 ("perf/core: Remove perf_event::group_entry")
... as the sibling's sibling_list would be empty. However, now that we
use the sibling_list field as both the list head and the list entry,
this leaves each sibling with a non-empty sibling list, including the
stale leader event.
If perf_group_detach() is subsequently called on a sibling, it will
appear to be a group leader, and we'll walk the sibling_list,
potentially dereferencing these stale events. In 0day testing, this has
been observed to result in kernel panics.
Let's avoid this by always removing siblings from the sibling list when
we promote them to leaders.
Fixes: 8343aae661 ("perf/core: Remove perf_event::group_entry")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.weaver@maine.edu
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: torvalds@linux-foundation.org
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: valery.cherepennikov@intel.com
Cc: linux-tip-commits@vger.kernel.org
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: alexander.shishkin@linux.intel.com
Cc: davidcc@google.com
Cc: kan.liang@intel.com
Cc: Dmitry.Prohorov@intel.com
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/r/20180316131741.3svgr64yibc6vsid@lakrids.cambridge.arm.com
We don't use the enum i9xx_plane_id namespace on SKL+ anymore, so
do not initialize the related plane_to_crtc_mapping[] table either.
Actually the only remaining user of that table is the pre-g4x
watermark code, but no harm in initializing the table on all
pre-SKL platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305174122.17273-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Device drivers use get_device_system_crosststamp() to produce precise
system/device cross-timestamps. The PHC clock and ALSA interfaces, for
example, make the cross-timestamps available to user applications. On
Intel platforms, get_device_system_crosststamp() requires a TSC value
derived from ART (Always Running Timer) to compute the monotonic raw and
realtime system timestamps.
Starting with Intel Goldmont platforms, the PCIe root complex supports the
PTM time sync protocol. PTM requires all timestamps to be in units of
nanoseconds. The Intel root complex hardware propagates system time derived
from ART in units of nanoseconds performing the conversion as follows:
ART_NS = ART * 1e9 / <crystal frequency>
When user software requests a cross-timestamp, the system timestamps
(generally read from device registers) must be converted to TSC by the
driver software as follows:
TSC = ART_NS * TSC_KHZ / 1e6
This is valid when CPU feature flag X86_FEATURE_TSC_KNOWN_FREQ is set
indicating that tsc_khz is derived from CPUID[15H]. Drivers should check
whether this flag is set before conversion to TSC is attempted.
Suggested-by: Christopher S. Hall <christopher.s.hall@intel.com>
Signed-off-by: Rajvi Jingar <rajvi.jingar@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Link: https://lkml.kernel.org/r/1520530116-4925-1-git-send-email-rajvi.jingar@intel.com
Toshiaki Makita says:
====================
Fix vlan untag and insertion for bridge and vlan with reorder_hdr off
As Brandon Carpenter reported[1], sending non-vlan-offloaded packets from
bridge devices ends up with corrupted packets. He narrowed down this problem
and found that the root cause is in skb_reorder_vlan_header().
While I was working on fixing this problem, I found that the function does
not work properly for double tagged packets with reorder_hdr off as well.
Patch 1 fixes these 2 problems in skb_reorder_vlan_header().
And it turned out that fixing skb_reorder_vlan_header() is not sufficient
to receive double tagged packets with reorder_hdr off while I was testing the
fix. Vlan tags got out of order when vlan devices with reorder_hdr disabled
were stacked. Patch 2 fixes this problem.
[1] https://www.spinics.net/lists/linux-ethernet-bridging/msg07039.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().
This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.
This patch fixes the behaviour by inserting the inner tag at the right
position.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().
The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.
The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.
In rx path single tag case, it works as follows:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+------+----
| ETH | VLAN | ETH |
| ADDRS | TPID | TCI | TYPE |
+-------------------+-------------+------+----
<-------- mac_len --------->
<------------->
to be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<-------- mac_len --------->
This is ok, but in rx double tag case, it corrupts packets:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+-------------+------+----
| ETH | VLAN | VLAN | ETH |
| ADDRS | TPID | TCI | TPID | TCI | TYPE |
+-------------------+-------------+-------------+------+----
<--------------- mac_len ---------------->
<------------->
should be removed
<--------------------------->
actually will be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<--------------- mac_len ---------------->
So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.
skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.
Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff111 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
added vxlan offload support for IPv6 pkts. Required change in
enic_udp_tunnel_del was not made. This creates a bug where once user
adds IPv6 tunnel, hw offload for that cannot be deleted.
This patch removes check for IP proto in tunnel delete path. Driver need
not check for IP proto since same UDP port cannot be used to create two
tunnels.
Fixes: d11790941d ("enic: Add vxlan offload support for IPv6 pkts")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3c181c12c4.
The offending patch was merged in 4.16-rc4 and was promptly applied to
stable kernels 4.14.25 and 4.15.8.
The patch causes a corruption in several superblock items on big-endian
machines because of messed up endianity conversions. The damage is
manually repairable. A filesystem cannot be mounted again after it has
been unmounted once.
We do a full revert and not a fixup so stable can pick that patch ASAP.
Fixes: 3c181c12c4 ("btrfs: use proper endianness accessors for super_copy")
Link: https://lkml.kernel.org/r/1521139304@msgid.manchmal.in-ulm.de
CC: stable@vger.kernel.org # 4.14+
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: David Sterba <dsterba@suse.com>
The variable 'len' is being initialized with a value that is never
read and it is re-assigned later, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
net/rxrpc/recvmsg.c:275:15: warning: Value stored to 'len' during its
initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we want to potentially support multiple different gamma/degamma
LUT sizes we can (and should) at least check that the blob length
is a multiple of the LUT entry size.
v2: s/expected_size_mod/expected_elem_size/ (Daniel)
Add kernel doc (Daniel)
v3: s/we/were/ typo in the docs
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152241.7113-1-ville.syrjala@linux.intel.com
Using a flexible array for the blob data was a mistake by me. It
forces all users of the blob data to cast blob->data to something
else. void* is clearly superior so let's go back to the original
scheme.
Not a clean revert as the code has moved.
This reverts commit d63f5e6bf6.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When using device passthrough with SME active, the MMIO range that is
mapped for the device should not be mapped encrypted. Add a check in
set_spte() to insure that a page is not mapped encrypted if that page
is a device MMIO page as indicated by kvm_is_mmio_pfn().
Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>