Commit graph

766,493 commits

Author SHA1 Message Date
Rafał Miłecki
1259055170 brcmfmac: drop Inter-Access Point Protocol packets by default
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.

Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.

This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups

To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
   disassociation perfromed by a firmware (possible local DoS attack).

It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.

This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-16 15:00:24 +02:00
Kalle Valo
1e2dce98c0 Third batch of iwlwifi fixes intended for 4.16:
* Fix an issue with the multicast queue;
 * Fix IGTK handling;
 * Fix some missing return value checks;
 * Add support for a HW workaround for issues on some platforms;
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlqrnicACgkQoUecoho8
 xfpY8g//aktEH+rM6tt3mfdVAq8qVTPdTbE/foM0IQ1kb1zRAb1WMS1RskxLjVZk
 AD8RTpmb7Qp7j5OaNZ8f5jgE60G7GdecQqueZZvsVFla39U9MCwQD7ZGyr/lKdQt
 jVFC64lDHUyKdRybaelKaBU/oiRWd4/pIpL0Tb/Dtxx7akmLnr6c3WhiL7/fTned
 cuQ5TVzdTGvunZzUnTAPA8vf+C++BKdjdxpL6BS4cxsSvIt6oYnTUemEfwuPYKiz
 sQzBYhf4pbt3Yd7FAMdQnny3qBgQ1+avTheM9SAOeIUxSrTx5c6rnUFqh9rXFDMO
 vZDkxnvmlVS1fWqATcRaD/7vAEku9hcTs4rjxfvM116y/sw2oPdjYAZ8l9OIL4Mb
 Kfj29+mKc4vRS6Gtt2mRMxIQvM1XoUFk45fynmdWI16Mm/0dYJA+qYtw4i6SV1eG
 ZrvG+nikp/k6VmEeEbkBI28wQCYyGuDODTk83dbcrWFS49hvtNkd3mo5o4BDNKHC
 R8b0afvTZVmosgGOf43BdSs6Qi6K7cXZDWWnRs/+piaYx4RH+vAbGSLEumXYI/H2
 nSeYvBcXEWEOoY//mzQryhwxpgj2tSUDDn/nBw7WKqWoL4zJlsU4GYP32lDKID+B
 MxpMhYK7vouooDVY3US1CfXraZVqDolngwdtbSE79nS+ma8ovKA=
 =Vhr7
 -----END PGP SIGNATURE-----

Merge tag 'iwlwifi-for-kalle-2018-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Third batch of iwlwifi fixes intended for 4.16:

* Fix an issue with the multicast queue;
* Fix IGTK handling;
* Fix some missing return value checks;
* Add support for a HW workaround for issues on some platforms;
2018-03-16 14:39:55 +02:00
Tvrtko Ursulin
22de4e7a53 drm/i915/pmu: Work around compiler warnings on some kernel configs
Arnd Bergman reports:
"""
The conditional spinlock confuses gcc into thinking the 'flags' value
might contain uninitialized data:

drivers/gpu/drm/i915/i915_pmu.c: In function '__i915_pmu_event_read':
arch/x86/include/asm/paravirt_types.h:573:3: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]

The code is correct, but it's easy to see how the compiler gets confused
here. This avoids the problem by pulling the lock outside of the function
into its only caller.
"""

On deeper look it seems this is caused by paravirt spinlocks
implementation when CONFIG_PARAVIRT_DEBUG is set, which by being
complicated, manages to convince gcc locked parameter can be changed
externally (impossible).

Work around it by removing the conditional locking parameters altogether.
(It was never the most elegant code anyway.)

Slight penalty we now pay is an additional irqsave spin lock/unlock cycle
on the event enable path. But since enable is not a fast path, that is
preferrable to the alternative solution which was doing MMIO under irqsave
spinlock.

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1fe699e301 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080535.17490-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ad055fb8e0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:41 +02:00
Chris Wilson
73e2232aa3 drm/i915: Only call tasklet_kill() on the first prepare_reset
tasklet_kill() will spin waiting for the current tasklet to be executed.
However, if tasklet_disable() has been called, then the tasklet is never
executed but permanently put back onto the runlist until
tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a
disable/enable pair. This is the case when we call set-wedge from inside
i915_reset(), and another request was submitted to us concurrent to the
reset.

Fixes: 963ddd63c3 ("drm/i915: Suspend submission tasklets around wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk
(cherry picked from commit 68ad361285)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:35 +02:00
Chris Wilson
7e9d3a4a1b drm/i915: Wrap engine->schedule in RCU locks for set-wedge protection
Similar to the staging around handling of engine->submit_request, we
need to stop adding to the execlists->queue prior to calling
engine->cancel_requests. cancel_requests will move requests from the
queue onto the timeline, so if we add a request onto the queue after that
point, it will be lost.

Fixes: af7a8ffad9 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-5-chris@chris-wilson.co.uk
(cherry picked from commit 47650db02d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:31 +02:00
Jani Nikula
84d4ebdb6c drm/i915/icl: do not save DDI A/E sharing bit for ICL
We don't want to preserve the DDI A 4 lane bit on ICL.

Fixes: 3d2011cfa4 ("drm/i915/icl: remove port A/E lane sharing limitation.")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306104155.3526-1-jani.nikula@intel.com
(cherry picked from commit 1e6aa7e55c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
2018-03-16 14:35:26 +02:00
Chris Wilson
957d32feaf drm/i915/stolen: Deduce base of reserved portion as top-size on vlv
On Valleyview, the HW deduces the base of the reserved portion of stolen
memory as being (top - size) and the address field within
GEN6_STOLEN_RESERVED is set to 0. Add yet another GEN6_STOLEN_RESERVED
reader to cope with the subtly different path required for vlv.

v2: Avoid using reserved_base = reserved_size = 0 as the invalid
condition as that typically falls outside of the stolen region,
provoking a consistency error.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-3-chris@chris-wilson.co.uk
2018-03-16 12:15:59 +00:00
Chris Wilson
0efb656147 drm/i915/stolen: Checkpatch cleansing
In the next patch, we will introduce a new vlv_get_stolen_reserved, so
before we do, make sure checkpatch is happy with the surrounding code.
Sneak in some debug output while we are here.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-2-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
2018-03-16 12:15:27 +00:00
Chris Wilson
0c65dfd1a8 drm/i915/stolen: Switch from DEBUG_KMS to DEBUG_DRIVER
i915_gem_stolen is an allocator for the reserved portion of memory
("stolen" from the system by the BIOS). It is not tied to KMS but
central to the driver, so prefer DRM_DEBUG_DRIVER.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180312165206.31772-1-chris@chris-wilson.co.uk
2018-03-16 12:14:30 +00:00
Rob Herring
101646a24a microblaze: switch to NO_BOOTMEM
Microblaze doesn't set CONFIG_NO_BOOTMEM and so memblock_virt_alloc()
doesn't work for CONFIG_HAVE_MEMBLOCK && !CONFIG_NO_BOOTMEM.

Similar change was already done by others architectures
"ARM: mm: Remove bootmem code and switch to NO_BOOTMEM"
(sha1: 84f452b1e8)
or
"openrisc: Consolidate setup to use memblock instead of bootmem"
(sha1: 266c7fad15)
or
"parisc: Drop bootmem and switch to memblock"
(sha1: 4fe9e1d957)
or
"powerpc: Remove bootmem allocator"
(sha1: 10239733ee)
or
"s390/mm: Convert bootmem to memblock"
(sha1: 50be634507)
or
"sparc64: Convert over to NO_BOOTMEM."
(sha1: 625d693e97)
or
"xtensa: drop sysmem and switch to memblock"
(sha1: 0e46c1115f)

Issue was introduced by:
"of/fdt: use memblock_virt_alloc for early alloc"
(sha1: 0fa1c57934)

Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:27 +01:00
Rob Herring
cd4dfee6a8 microblaze: remove unused alloc_maybe_bootmem
alloc_maybe_bootmem is unused, so remove it.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:27 +01:00
Michal Simek
18ffc0cce4 microblaze: Setup dependencies for ASM optimized lib functions
The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-16 12:51:26 +01:00
Alexander Sergeyev
e3b3121fa8 x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.

Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain
2018-03-16 12:33:11 +01:00
Thierry Reding
e7f4da4c44 phy: tegra: xusb: Uncomment register write
The reason why this was originally commented out is no longer clear. The
UPHY driver for SATA works fine with or without this change. The reset
value of the XDIGCLK_EN bit is 0, so unless programmed by the bootloader
this shouldn't make a difference anyway.

Define a macro for this bit and uncomment the code. This also fixes a
coverity issue brought to my attention by Rohith because not only is the
XDIGCLK_EN field modification commented out, but also the register write
which causes none of the earlier modifications of the register value to
be written to the register and the value being overwritten.

Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:38 +05:30
Enric Balletbo i Serra
ec1fcd7b7e phy: rockchip-typec: fall back to working in host-mode if extcon is missing.
Right now the rockchip type-c phy does fail probing when no extcon is
detected. Some boards get the cable-state via the extcon interface and
have this supported, other boards seem to use the fusb302 chip or
another but the driver currently does not seem to utilize the extcon
interface to report the cable-state. And, other, just connect the type-c
to a standard USB-A port so use no controller at all. A missing extcon
shouldn't fail to probe, instead, should just fall back to working in
host-mode if it cannot get the extcon.

Fixes: c301b327ae ("arm64: dts: rockchip: add usb3-phy otg-port support for rk3399")
Reported-by: Vicente Bergas <vicencb@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:37 +05:30
Enric Balletbo i Serra
21bf9bc2a9 dt-bindings: phy-rockchip-typec: move extcon property to be optional.
The extcon property is used to detect the cable-state but some boards
just connect the type-c phy to a regular USB-A connector without any
power-delivery and thus no controller reporting the cable-state.
So the extcon property is not really a required property, move it to be
optional instead.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:36 +05:30
Chris Zhong
866d4087f3 phy: rockchip-typec: support DP phy switch
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:35 +05:30
Chris Zhong
5eac5e9c0f phy: rockchip-typec: force to USB2 if DP at 4 lanes mode
The usb3tousb2_en BIT will be clear to 0 in probe(), it make USB
controller work at USB3 mode, and if the USB phy is turned on with DP
only mode(4 lanes DP), the rockchip_usb3_phy_power_on() will return
directly, so usb3_host_disable and usb3_host_port these 2 BIT will keep
a same value as coreboot. In coreboot, these 3 BITs are set as USB2
mode, but now one of the bits is changed to USB3, it make USB controller
work at a unknown status.

These 3 BITs should be changed to USB2, if the Type-C works at 4 lanes
mode, and then switch it back to USB3 mode, when USB disconnect.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:34 +05:30
William wu
f293f7409f phy: rockchip-typec: enable usb3 host during usb3 phy power on
We have forced usb3 to work in usb2 only mode in firmware by setting
usb3tousb2_en (bit3 of GRF_USB3PHY0/1_CON0) to 1, and setting
host_u3_port_disable (bit0 of GRF_USB3OTG0/1_CON1) to 1 and host_u3_port
(bit15~12 of GRF_USB3OTG0/1_CON1) to 0. So we need to re-enable usb3
host.

Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. And according to the TRM, it doesn't require that we should
clear the usb3tousb2 bit before pipe ready. So let's enable the usb3
host after pipe ready to avoid the Type-C PHY initialization failure.

Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:33 +05:30
Enric Balletbo i Serra
6912d4f40b dt-bindings: phy-rockchip-typec: deprecate some register properties.
As now the following register properties are in the driver, document as
deprecated these properties and recommend to not use them on new bindings.

The deprecated properties are:

- rockchip,typec-conn-dir : the register of type-c connector direction
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
                           enable control.
- rockchip,external-psm : the register of type-c phy external psm clock
                          selection.
- rockchip,pipe-status : the register of type-c phy pipe status.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:32 +05:30
Enric Balletbo i Serra
0fbc47d9e4 phy: rockchip-typec: deprecate some DT properties for various register fields.
Adding properties for various register fields in the DT doesn't scale and
this information should be in the driver instead.

Before this patch these registers (description below) were specified in
the DT, every register node contained 3 sections: offset, enable bit,
write mask bit.

 - rockchip,typec-conn-dir : the register of type-c connector direction,
   for type-c phy0, it must be <0xe580 0 16>;
   for type-c phy1, it must be <0xe58c 0 16>;
 - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
   enable control.
   for type-c phy0, it must be <0xe580 3 19>;
   for type-c phy1, it must be <0xe58c 3 19>;
 - rockchip,external-psm : the register of type-c phy external psm clock
   selection.
   for type-c phy0, it must be <0xe588 14 30>;
   for type-c phy1, it must be <0xe594 14 30>;
 - rockchip,pipe-status : the register of type-c phy pipe status.
   for type-c phy0, it must be <0xe5c0 0 0>;
   for type-c phy1, it must be <0xe5c0 16 16>;

After this patch these register definitions are in the driver. So can be
removed from the DT. Note that there are 2 type-c phys for RK3399 with
different offsets, the driver checks the phy base address of the running
instance and applies the right offsets.

Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:31 +05:30
Tony Lindgren
5d1ebbda03 phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4
Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
It is used on some Motorola Mapphone series of phones and tablets such
as Droid 4.

The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
device it seems. We know this as we get L3 errors from omap-usb-host if
trying to use the PHY before MDM6600 is configured.

The GPIOs controlling MDM6600 are used to power device on and off, to
configure the USB start-up mode (normal mode versus USB flashing), and
they also tell the state of the MDM6600 device.

The two start-up mode GPIOs are dual-purposed and used for out of band
(OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
the USB start-up mode first to get MDM6600 booted in the right mode to
be usable in the first place.

Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
driver for modems. But it really does not control the radio at all, it
just controls the modem power and start-up mode for USB. So I came to
the conclusion that we're better off having this done in the USB PHY
driver. For adding support for USB flashing mode, we can later on add
a kernel module option for flash_mode=1 or something similar.

Also note that currently there is no PM runtime support for the OHCI
on omap variant SoCs. So for low(er) power idle states, currenty both
ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.

For reference here is what I measured for total power consumption on
an idle Droid 4 with and without USB related MDM6600 modules:

idle lcd off	phy-mapphone-mdm6600	ohci-platform
153mW		284mW			344mW

So it seems that MDM6600 is currently not yet idling even with it's
radio turned off, but that's something that is beyond the control of
this USB PHY driver. This patch does get us to the point where modem
data and GPS are usable with libqmi and ModemManager for example.
Voice calls need more audio driver work.

Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:30 +05:30
Pengcheng Li
ba8b0ee81f phy: add inno-usb2-phy driver for hi3798cv200 SoC
It adds inno-usb2-phy driver for hi3798cv200 SoC USB 2.0 support.  One
inno-usb2-phy device can support up to two PHY ports.  While there is
device level reference clock and power reset to be controlled, each PHY
port has its own utmi reset that needs to assert/de-assert as needed.

Hi3798cv200 needs to access PHY port0 register via particular peripheral
syscon controller register to control PHY, like turning on PHY clock.

Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:29 +05:30
Pengcheng Li
d581ba62f3 dt-bindings: add bindings doc for HiSilicon INNO USB2 PHY
It adds device tree bindings document for HiSilicon INNO USB2 PHY.

Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:28 +05:30
Yoshihiro Shimoda
0147b57e73 dt-bindings: rcar-gen3-phy-usb3: Add bindings for r8a77965
This patch adds bindings for r8a77965 (R-Car M3-N).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:27 +05:30
Yoshihiro Shimoda
44e42df6b9 phy: rcar-gen3-usb2: Add support for r8a77965
This patch adds support for r8a77965 (R-Car M3-N). This SoC has
dedicated pins.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:26 +05:30
Yoshihiro Shimoda
b1ba68f33c dt-bindings: rcar-gen3-phy-usb2: Add bindings for r8a77965
This patch adds support for r8a77965 (R-Car M3-N).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:55:25 +05:30
Amelie Delaunay
94c358da3a phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds phy transceiver driver for STM32 USB PHY Controller
(USBPHYC) that provides dual port High-Speed phy for OTG (single port)
and EHCI/OHCI host controller (two ports).
One port of the phy is shared between the two USB controllers through
a UTMI+ switch.

[fengguang.wu@intel.com: Make stm32_usbphyc_get_pll_params() to be static]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 16:53:00 +05:30
Chris Zhong
0a00ac97d2 drm/rockchip: cdn-dp: remove the DP phy switch
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.

If the board has 2 Type-C ports, the DP driver get the phy id from
devm_of_phy_get_by_index, and then control this switch according to
this id. But some others board only has one Type-C port, it may be PHY 0
or PHY 1. The dts node id can not tell us the correct PHY id. Hence move
this switch to PHY driver, the PHY driver can distinguish between PHY 0
and PHY 1, and then write the correct register bit.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[The phy-changes are in the phy-tree now and the cdn-dp wasn't
 enabled at all so far, so this change can go through drm-misc
 alone without causing issues when testing drm-misc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
2018-03-16 11:51:11 +01:00
Luca Coelho
86a2b2043a iwlwifi: add shared clock PHY config flag for some devices
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations.  We need to set a bit in the phy
configuration to indicate that to the FW.  To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware.  And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.

Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:54 +02:00
Johannes Berg
75fd4fec3e iwlwifi: mvm: fix error checking for multi/broadcast sta
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.

Found by smatch:

.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'

Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:53 +02:00
Beni Lev
e829b17caf iwlwifi: mvm: Correctly set IGTK for AP
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.

Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:52 +02:00
Emmanuel Grumbach
334167decf iwlwifi: mvm: set the correct tid when we flush the MCAST sta
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.

The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.

To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.

Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-03-16 12:34:52 +02:00
Chris Wilson
ac697ae801 drm/i915: Stop engines when declaring the machine wedged
If we fail to reset the GPU, we declare the machine wedged. However, the
GPU may well still be running in the background with an in-flight
request. So despite our efforts in cleaning up the request queue and
faking the breadcrumb in the HWSP, the GPU may eventually write the
in-flght seqno there breaking all of our assumptions and throwing the
driver into a deep turmoil, wedging beyond wedged.

To avoid this we ideally want to reset the GPU. Since that has already
failed, make sure the rings have the stop bit set instead. This is part
of the normal GPU reset sequence, but that is actually disabled by
igt/gem_eio to force the wedged state. If we assume the worst, we must
poke at the bit again before we give up.

v2: Move the intel_gpu_reset() from set-wedged in the reset error path
into i915_gem_set_wedged() itself. Even if the reset fails (e.g. if it is
disabled by gem_eio), it still tries to make sure the engines are
stopped. For i915_gem_set_wedged() callers from outside of i915_reset(),
this should make sure the GPU is disabled while the driver is marked as
being wedged.

Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315151015.22741-1-chris@chris-wilson.co.uk
2018-03-16 10:16:08 +00:00
Chris Wilson
d9b13c4dde drm/i915: Trace GEM steps between submit and wedging
We still have an odd race with wedging/unwedging as shown by igt/gem_eio
that defies expectations. Add some more trace_printks to try and
visualize the flow over the precipice.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315131451.4060-1-chris@chris-wilson.co.uk
2018-03-16 10:16:07 +00:00
Arnd Bergmann
79375ea3ec mm: remove obsolete alloc_remap()
Tile was the only remaining architecture to implement alloc_remap(),
and since that is being removed, there is no point in keeping this
function.

Removing all callers simplifies the mem_map handling.

Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:13 +01:00
Arnd Bergmann
1a8429132e mm: remove blackfin MPU support
The CONFIG_MPU option was only defined on blackfin, and that architecture
is now being removed, so the respective code can be simplified.

A lot of other microcontrollers have an MPU, but I suspect that if we
want to bring that support back, we'd do it differently anyway.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:10 +01:00
Arnd Bergmann
e05a959f4b procfs: remove CONFIG_HARDWALL dependency
Hardwall is a tile specific feature, and with the removal of the
tile architecture, this has become dead code, so let's remove it.

Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:08 +01:00
Jesper Nilsson
c690eddc2f CRIS: Drop support for the CRIS port
The port was added back in 2000 so it's no longer even a good source
of inspiration for newer ports (if it ever was)

The last SoC (ARTPEC-3) with a CRIS main CPU was launched in 2008.

Coupled with time and working developer board hardware being
in low supply, it's time to drop the port from Linux.

So long and thanks for all the fish!

Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:05 +01:00
Arnd Bergmann
bb9d812643 arch: remove tile port
The Tile architecture port was added by Chris Metcalf in 2010, and
maintained until early 2018 when he orphaned it due to his departure
from Mellanox, and nobody else stepped up to maintain it. The product
line is still around in the form of the BlueField SoC, but no longer
uses the Tile architecture.

There are also still products for sale with Tile-GX SoCs, notably the
Mikrotik CCR router family. The products all use old (linux-3.3) kernels
with lots of patches and won't be upgraded by their manufacturers. There
have been efforts to port both OpenWRT and Debian to these, but both
projects have stalled and are very unlikely to be continued in the future.

Given that we are reasonably sure that nobody is still using the port
with an upstream kernel any more, it seems better to remove it now while
the port is in a good shape than to let it bitrot for a few years first.

Cc: Chris Metcalf <chris.d.metcalf@gmail.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: http://www.mellanox.com/page/npu_multicore_overview
Link: https://jenkins.debian.net/view/rebootstrap/job/rebootstrap_tilegx_gcc7/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:56:03 +01:00
Arnd Bergmann
4ba66a9760 arch: remove blackfin port
The Analog Devices Blackfin port was added in 2007 and was rather
active for a while, but all work on it has come to a standstill
over time, as Analog have changed their product line-up.

Aaron Wu confirmed that the architecture port is no longer relevant,
and multiple people suggested removing blackfin independently because
of some of its oddities like a non-working SMP port, and the amount of
duplication between the chip variants, which cause extra work when
doing cross-architecture changes.

Link: https://docs.blackfin.uclinux.org/
Acked-by: Aaron Wu <Aaron.Wu@analog.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mike Frysinger <vapier@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-16 10:55:47 +01:00
Ulf Hansson
f09a7931bc Merge branch 'fixes' into next 2018-03-16 10:06:19 +01:00
Daniel Borkmann
318df9f01c Merge branch 'bpf-tools-build-improvements'
Jakub Kicinski says:

====================
As promised this series addresses nits and minor issues in tools/bpf
build infra.  One GCC-7 warning which is nice to get rid of.  Dependencies
when built with OUTPUT are fixed.  make clean will now remove the
FEATURE-DUMP.* files.  PHONY target is also updated to match reality.
====================

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:25:11 +01:00
Jakub Kicinski
cc5b3403f0 tools: bpf: remove feature detection output
bpf tools use feature detection for libbfd dependency, clean up
the output files on make clean.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:46 +01:00
Jakub Kicinski
8050ea4653 tools: bpf: cleanup PHONY target
There is no FORCE target in the Makefile and some of the PHONY
targets are missing, update the list.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:31 +01:00
Jakub Kicinski
d5fc73dceb tools: bpftool: fix potential format truncation
GCC 7 complains:

xlated_dumper.c: In function ‘print_call’:
xlated_dumper.c:179:10: warning: ‘%s’ directive output may be truncated writing up to 255 bytes into a region of size between 249 and 253 [-Wformat-truncation=]
     "%+d#%s", insn->off, sym->name);

Add a bit more space to the buffer so it can handle the entire
string and integer without truncation.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:23:15 +01:00
Jakub Kicinski
90126e3a40 tools: bpftool: fix dependency file path
Auto-generated dependency files are in the OUTPUT directory,
we need to include them from there.  This fixes object files
not being rebuilt after header changes.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-03-16 09:22:55 +01:00
Amelie Delaunay
194303d60b dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds the device tree bindings description for STM32 USBPHYC
(USB PHY Controller).

Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:46 +05:30
Masahiro Yamada
bb0e500bed phy: add 'depends on HAS_IOMEM' to fix unmet dependency
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.

Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.

Detected by "make ARCH=score allyesconfig".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:45 +05:30
Martin Blumenstingl
115de9fd68 phy: amlogic: add USB3 PHY support for Meson GXL and GXM
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).

Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
  dwc3 controller only has USB2 ports enabled) we need to initialize the
  USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
  initialization high-speed USB devices (especially USB hard disks and
  thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
  it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
  USB2 PHY between host and peripheral (aka device) mode. an interrupt
  can be used to detect changes between host and device mode.

There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
  logic (on the GXL and GXM SoCs these are the same clock and reset line
  as for the USB3 PHY itself, but Amlogic sees this as two different
  components - even though they share the same register space - so they
  have to be passed individually to allow specifying different inputs on
  other SoCs if needed)
- the interrupt for the OTG detection logic

The whole OTG detection logic is not implemented yet.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-03-16 13:40:44 +05:30