Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/wmi.c:331
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a hardware issue in Intel Baytrail where concurrent GPIO register
access might result reads of 0xffffffff and writes might get dropped
completely.
Prevent this from happening by taking the serializing lock in all places
where it is possible that more than one thread might be accessing the
hardware concurrently.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FSF address is already mentioned in the COPYING file. No need to
duplicate that information to individual files.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_hst.c:171
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:277
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:206
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gpio can keep state even the clock disable, for save power
consumption, only enable gpio clock when it setting
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial change, fix spelling mistake 'invaild' -> 'invalid' in
dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the PTN3460 driver has been rewritten as a proper I2C driver
and there is infrastructure to hook up the bridge with a DRM device, it
is no longer necessary to have this dependency to ensure the correct
build mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
With commit b17d1bf16c ("gpio: make flags mandatory for gpiod_get functions")
it becomes necessary to pass the flags argument. And this patch adds the gpio
header file to fix the build breakage when build testing with random
configuration files.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
At the last iteration of the loop, j may equal zero and thus
tp_list[j - 1] causes an invalid read.
Change the logic of the loop so that j - 1 is always >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move all code into the new canonical ->disable() and ->enable() helper
callbacks so that they play extra nice with atomic DPMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
While at it, remove the enabled field that hasn't been used since the
demidlayering of the output drivers done in preparation for the atomic
mode-setting conversion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating most of the code to set up a debugfs file, use
the existing DRM core debugfs infrastructure instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head state registers are per head, so they must be properly indexed.
This has worked fine so far because all boards with eDP use it as the
primary output, so it is very likely to end up attached to head 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The data structure is always only read, never written, and can hence be
referred to by a const pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tearing down debugfs support, make sure to reset the fields to NULL
in the correct order, otherwise the debugfs root will not be properly
removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM minor is needed to teardown debugfs, so it needs to be tracked
to prevent a crash on driver removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the SOR device fails, output proper error messages to help
diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TRM lists indexed registers without an underscore to separate name
from index. Use that convention in the driver for consistency.
While at it, rename some of the field names to the names used in the
TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to platform_driver_register() will already set up the .owner
field, so there's no need to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The horizontal pulse enable bits are named H_PULSE{0,1,2}_ENABLE in the
TRM. Modify the driver to use the same naming for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Record interrupt statistics, such as the number of frames and VBLANKs
received and the number of FIFO underflow and overflows.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Request a syncpoint for display prior to registering the host1x client.
This will ensure that the syncpoint will be acquired when the KMS driver
initializes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver load, reset the VBLANK machinery to off to reflect the
hardware state. Since the ->reset() callback is called from the initial
drm_mode_config_reset() call, move the latter after the VBLANK machinery
initialization by drm_vblank_init().
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dev->name of CODEC might not be identical to its codec_dai_name,
so using dev->name to probe the CODEC dai is not a correct approach.
This patch specifies each supporting codec_dai_name instead of using
dev->name any more.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
