The "i" here is always equal to "btf_type_vlen(t)" since
the "for_each_member()" loop never breaks.
Signed-off-by: Kui-Feng Lee <thinker.li@gmail.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20240203055119.2235598-1-thinker.li@gmail.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Calling spi_sync() unconditionally sets the spi field of struct
spi_message. Therefore setting msg.spi = spi before calling spi_sync()
has no effect and can be removed.
(spi_message_add_tail() does not access this field.)
Signed-off-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240201201248.2334798-2-dlechner@baylibre.com
The CW1200 uses two GPIOs to control the powerup and reset
pins, get these from GPIO descriptors instead of being passed
as platform data from boardfiles.
The RESET line will need to be marked as active low as we will
let gpiolib handle the polarity inversion.
The SDIO case is a bit special since the "card" need to be
powered up before it gets detected on the SDIO bus and
properly probed. Fix this by using board-specific GPIOs
assigned to device "NULL".
There are currently no in-tree users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-6-e1c7c5d68746@linaro.org
The mwifiex driver include two legacy GPIO headers but does
not use symbols from any of them.
The driver does contain some "gpio" handling code, but this
is some custom GPIO interface, not the Linux GPIO.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-4-e1c7c5d68746@linaro.org
The driver is using all the modern abstractions to obtain and use
GPIOs and the legacy <linux/gpio.h> header is unused, so drop it.
Fixes: a8e59744e1 ("gpiolib: split linux/gpio/driver.h out of linux/gpio.h")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240131-descriptors-wireless-v1-3-e1c7c5d68746@linaro.org
Sparse warns:
drivers/net/wireless/st/cw1200/cw1200_spi.c:83:17: got restricted __le16 [usertype]
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: warning: incorrect type in assignment (different base types)
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: expected unsigned short [addressable] [assigned] [usertype] regaddr
drivers/net/wireless/st/cw1200/cw1200_spi.c:148:17: got restricted __le16 [usertype]
These cpu_to_le16() calls are not really making any sense to me. On a big
endian system we first convert regaddr from big to little using cpu_to_le16()
but immediately after we convert them back to big endian? So just remove them.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-4-kvalo@kernel.org
drivers/net/wireless/rsi/rsi_91x_usb.c:235:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:236:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:237:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:238:27: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:244:36: warning: restricted __le32 degrades to integer
drivers/net/wireless/rsi/rsi_91x_usb.c:245:35: warning: restricted __le32 degrades to integer
These cpu_to_le32() are not making sense. With usb_reg_buf we handle the values
byte at a time to make sure usb_reg_buf is in little endian so no need to
convert anything. And usb_control_msg() expects to have the values in native
endian anyway. So just remove these so they are not spamming our logs.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-3-kvalo@kernel.org
Sparse warns:
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:383:24: warning: implicit cast from nocast type
drivers/net/wireless/zydas/zd1211rw/zd_usb.c:419:24: warning: implicit cast from nocast type
This is an ancient driver which has not have any meaningfuli changes for a long
time and hopefully removed soon. So just remove the __nocast to get rid of the
sparse warnings.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240130151556.2315951-2-kvalo@kernel.org
TP-Link TL-WN823N V2 (2357:0135) is based on rtl8192fu and has been
tested to work with the rtl8xxxu driver.
Signed-off-by: Chun Qiu <cqca@cock.lu>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240129053030.16369-1-cqca@cock.lu
In the for statement of lbs_allocate_cmd_buffer(), if the allocation of
cmdarray[i].cmdbuf fails, both cmdarray and cmdarray[i].cmdbuf needs to
be freed. Otherwise, there will be memleaks in lbs_allocate_cmd_buffer().
Fixes: 876c9d3aeb ("[PATCH] Marvell Libertas 8388 802.11b/g USB driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126075336.2825608-1-alexious@zju.edu.cn
Copy cck and ofdm separately in order to avoid __read_overflow2_field
warning.
Fixes: f75e4779d2 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240203132446.54790-1-nbd@nbd.name
Skip updating workqueues with __WQ_DESTROYING bit set when updating
global unbound cpumask to avoid unnecessary work and other complications.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Function nvkm_gsp_radix3_sg() uses nvkm_gsp_mem objects to allocate the
radix3 tables, but it unnecessarily creates those objects manually
instead of using the standard nvkm_gsp_mem_ctor() function like the
rest of the code does.
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202230608.1981026-2-ttabi@nvidia.com
Nouveau manages GSP-RM DMA buffers with nvkm_gsp_mem objects. Several of
these buffers are never dealloced. Some of them can be deallocated
right after GSP-RM is initialized, but the rest need to stay until the
driver unloads.
Also futher bullet-proof these objects by poisoning the buffer and
clearing the nvkm_gsp_mem object when it is deallocated. Poisoning
the buffer should trigger an error (or crash) from GSP-RM if it tries
to access the buffer after we've deallocated it, because we were wrong
about when it is safe to deallocate.
Finally, change the mem->size field to a size_t because that's the same
type that dma_alloc_coherent expects.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 176fdcbddf ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Signed-off-by: Timur Tabi <ttabi@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202230608.1981026-1-ttabi@nvidia.com
The number of possible CPUs is set be kernel in early boot time through
some discovery mechanisms, like ACPI in x86. We have a parameter both
in x86 and S390 to override that - there are some cases of BIOSes exposing
more possible CPUs than the available ones, so this parameter is a good
testing mechanism, but for some reason wasn't mentioned so far in the
kernel parameters guide - let's fix that.
Cc: Changwoo Min <changwoo@igalia.com>
Signed-off-by: "Guilherme G. Piccoli" <gpiccoli@igalia.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240203152208.1461293-1-gpiccoli@igalia.com
This reverts commit d412ace111. This leads to
build failures as it depends on a driver-core commit 32f78abe59 ("driver
core: bus: constantify subsys_register() calls"). Let's drop it from wq tree
and route it through driver-core tree.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402051505.kM9Rr3CJ-lkp@intel.com/
After calling throtl_peek_queued(), the data direction can be determined so
there is no need to call bio_data_dir() to check the direction again.
Signed-off-by: Tang Yizhou <yizhou.tang@shopee.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20240123081248.3752878-1-yizhou.tang@shopee.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mark the task as having a cached timestamp when set assign it, so we
can efficiently check if it needs updating post being scheduled back in.
This covers both the actual schedule out case, which would've flushed
the plug, and the preemption case which doesn't touch the plugged
requests (for many reasons, one of them being then we'd need to have
preemption disabled around plug state manipulation).
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Querying the current time is the most costly thing we do in the block
layer per IO, and depending on kernel config settings, we may do it
many times per IO.
None of the callers actually need nsec granularity. Take advantage of
that by caching the current time in the plug, with the assumption here
being that any time checking will be temporally close enough that the
slight loss of precision doesn't matter.
If the block plug gets flushed, eg on preempt or schedule out, then
we invalidate the cached clock.
On a basic peak IOPS test case with iostats enabled, this changes
the performance from:
IOPS=108.41M, BW=52.93GiB/s, IOS/call=31/31
IOPS=108.43M, BW=52.94GiB/s, IOS/call=32/32
IOPS=108.29M, BW=52.88GiB/s, IOS/call=31/32
IOPS=108.35M, BW=52.91GiB/s, IOS/call=32/32
IOPS=108.42M, BW=52.94GiB/s, IOS/call=31/31
IOPS=108.40M, BW=52.93GiB/s, IOS/call=32/32
IOPS=108.31M, BW=52.89GiB/s, IOS/call=32/31
to
IOPS=118.79M, BW=58.00GiB/s, IOS/call=31/32
IOPS=118.62M, BW=57.92GiB/s, IOS/call=31/31
IOPS=118.80M, BW=58.01GiB/s, IOS/call=32/31
IOPS=118.78M, BW=58.00GiB/s, IOS/call=32/32
IOPS=118.69M, BW=57.95GiB/s, IOS/call=32/31
IOPS=118.62M, BW=57.92GiB/s, IOS/call=32/31
IOPS=118.63M, BW=57.92GiB/s, IOS/call=31/32
which is more than a 9% improvement in performance. Looking at perf diff,
we can see a huge reduction in time overhead:
10.55% -9.88% [kernel.vmlinux] [k] read_tsc
1.31% -1.22% [kernel.vmlinux] [k] ktime_get
Note that since this relies on blk_plug for the caching, it's only
applicable to the issue side. But this is where most of the time calls
happen anyway. On the completion side, cached time stamping is done with
struct io_comp patch, as long as the driver supports it.
It's also worth noting that the above testing doesn't enable any of the
higher cost CPU items on the block layer side, like wbt, cgroups,
iocost, etc, which all would add additional time querying and hence
overhead. IOW, results would likely look even better in comparison with
those enabled, as distros would do.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert any user of ktime_get_ns() to use blk_time_get_ns(), and
ktime_get() to blk_time_get(), so we have a unified API for querying the
current time in nanoseconds or as ktime.
No functional changes intended, this patch just wraps ktime_get_ns()
and ktime_get() with a block helper.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for moving time keeping into blk.h, move the cgroup
related code for timestamps in here too. This will help avoid a circular
dependency, and also moves it into a more appropriate header as this one
is private to the block layer code.
Leave struct bio_issue in blk_types.h as it's a proper time definition.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Share the main merge / split / integrity preparation code between the
cached request vs newly allocated request cases, and add comments
explaining the cached request handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new helper to check if there is suitable cached request in
blk_mq_submit_bio. This removes open coded logic in blk_mq_submit_bio
and moves some checks that so far are in blk_mq_use_cached_rq to
be performed earlier. This avoids the case where we first do check
with the cached request but then later end up allocating a new one
anyway and need to grab a queue reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_attempt_bio_merge has nothing to do with allocating a new
request, it avoids allocating a new request. Move the call out of
blk_mq_get_new_requests and into the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, at the end of ath11k_mac_fill_reg_tpc_info(), the
reg_tpc_info struct is populated, including the following:
reg_tpc_info->is_psd_power = is_psd_power;
reg_tpc_info->eirp_power = eirp_power;
Kernel test robot complains on uninitialized symbol:
drivers/net/wireless/ath/ath11k/mac.c:7949
ath11k_mac_fill_reg_tpc_info() error: uninitialized symbol 'eirp_power'.
This is because there are some code paths that never set eirp_power, so
the assignment of reg_tpc_info->eirp_power can come from an
uninitialized variable. Functionally this is OK since the eirp_power
only has meaning when is_psd_power is true, and all code paths which set
is_psd_power to true also set eirp_power. However, to keep the robot
happy, always initialize eirp_power before use.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 92425f788f ("wifi: ath11k: fill parameters for vdev set tpc power WMI command")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202024011.11341-1-quic_bqiang@quicinc.com
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
To reduce power consumption enable 802.11 power save mode in
station mode. This allows both radio and CPU to sleep more.
Only enable the mode on WCN7850, other chips don't support it
for now.
To test that power save mode is running, run below command and
check there is no NULL Data frame seen by a sniffer:
iw dev <inf> set power_save off
And run below command, then check there is a NULL Data frame
in sniffer:
iw dev <inf> set power_save on
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com
In a rather unusual arrangement in include/media/v4l2-vp9.h struct
v4l2_vp9_frame_symbol_counts has fields that are arrays of pointers, not a
pointer to an array, which is what's usually done.
Add support for such arrays of pointers to kernel-doc.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240131084934.191226-1-sakari.ailus@linux.intel.com
Timur pointed this out before, and it just slipped my mind,
but this might help some things work better, around pcie power
management.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 8d55b0a940 ("nouveau/gsp: add some basic registry entries.")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240130032643.2498315-1-airlied@gmail.com
The example for PCI devices has some addressing errors. 'reg' is written
as if the parent bus is PCI, but the default bus for examples is 1
address and size cell. 'ranges' is defining config space with a
size of 0. Generally, config space should not be defined in
'ranges', only PCI memory and I/O spaces. Fix these issues by updating
the values with made-up, but valid values.
This was uncovered with recent dtschema changes.
Link: https://lore.kernel.org/r/20240122173514.935742-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Make the pattern matching node names a bit stricter to improve DTS
consistency. The pattern is restricted to -N suffixes to decimal
numbers.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20240109082511.15278-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Static FDPIC executable may get an executable stack even when it has
non-executable GNU_STACK segment. This happens when STACK segment has rw
permissions, but does not specify stack size. In that case FDPIC loader
uses permissions of the interpreter's stack, and for static executables
with no interpreter it results in choosing the arch-default permissions
for the stack.
Fix that by using the interpreter's properties only when the interpreter
is actually used.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20240118150637.660461-1-jcmvbkbc@gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
udf_load_logicalvolint() loads logical volume integrity descriptors.
Since there can be multiple blocks with LVIDs, we verify the contents of
only the last (prevailing) LVID found. However if we fail to load the
last LVID (either due to IO error or because it's checksum fails to
match), we never perform the verification of validity of the LVID we are
going to use. If such LVID contains invalid data, we can hit
out-of-bounds access or similar issues. Fix the problem by verifying
each LVID we are potentially going to accept.
Reported-by: Robert Morris <rtm@csail.mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
AFAICS there is no hardware restriction on where in ggtt
the hdcp gsc message object needs to be bound. And as it's
a regular shmem object we don't need it be in the mappabe
range either. So pin it high to make avoid needlessly
wasting the precious mappable range for it.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215110933.9188-3-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
intel_hdcp_component_init()->...->intel_hdcp_gsc_initialize_message()
will allocate ggtt address space for some hdcp gsc message thing.
That is currently being done way too early as we haven't even
taken over the BIOS fb yet. So this has the potential of corrupting
ggtt PTEs that need to be preserved until the BIOS fb takover
is done.
Only call intel_hdcp_component_init() once all the BIOS fb takeover,
and full ggtt init (which currently also needs to reserve very
specific ranges of ggtt, thus assuming that no one else has stolen
them yet) is done.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215110933.9188-2-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Below race may cause NULL pointer dereference
P1 P2
dquot_free_inode quota_off
drop_dquot_ref
remove_dquot_ref
dquots = i_dquot(inode)
dquots = i_dquot(inode)
srcu_read_lock
dquots[cnt]) != NULL (1)
dquots[type] = NULL (2)
spin_lock(&dquots[cnt]->dq_dqb_lock) (3)
....
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
The Keystone platforms used their own keystone_defconfig mostly to
enable CONFIG_ARM_LPAE which could not be added to the multi_v7 config.
Now that we have multi_v7_lpae_defconfig/lpae.config target we can and
should use that defconfig for Keystone. Add the remaining must-have
options for Keystone support to multi_v7_defconfig.
TI_SCI_*:
TI_MESSAGE_MANAGER:
Allows TI-SCI communication with system control firmware (PMMC) on K2G.
TI_KEYSTONE_NETCP*:
KEYSTONE_NAVIGATOR*:
Network driver, needed for NFS boot.
PCI_KEYSTONE*:
CAN_C_CAN*:
INPUT_GPIO_DECODER:
SPI_CADENCE_QUADSPI:
PWM_TIECAP:
Miscellaneous on-chip peripherals. Added as modules where possible.
RESET_TI*:
Used by DSP Remoteproc driver.
bloat-o-meter:
add/remove: 387/0 grow/shrink: 6/0 up/down: 130945/0 (130945)
Total: Before=22791863, After=22922808, chg +0.57%
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240125163145.87055-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
A recent change to check_for_locks() changed it to take ->flc_lock while
holding ->fi_lock. This creates a lock inversion (reported by lockdep)
because there is a case where ->fi_lock is taken while holding
->flc_lock.
->flc_lock is held across ->fl_lmops callbacks, and
nfsd_break_deleg_cb() is one of those and does take ->fi_lock. However
it doesn't need to.
Prior to v4.17-rc1~110^2~22 ("nfsd: create a separate lease for each
delegation") nfsd_break_deleg_cb() would walk the ->fi_delegations list
and so needed the lock. Since then it doesn't walk the list and doesn't
need the lock.
Two actions are performed under the lock. One is to call
nfsd_break_one_deleg which calls nfsd4_run_cb(). These doesn't act on
the nfs4_file at all, so don't need the lock.
The other is to set ->fi_had_conflict which is in the nfs4_file.
This field is only ever set here (except when initialised to false)
so there is no possible problem will multiple threads racing when
setting it.
The field is tested twice in nfs4_set_delegation(). The first test does
not hold a lock and is documented as an opportunistic optimisation, so
it doesn't impose any need to hold ->fi_lock while setting
->fi_had_conflict.
The second test in nfs4_set_delegation() *is* make under ->fi_lock, so
removing the locking when ->fi_had_conflict is set could make a change.
The change could only be interesting if ->fi_had_conflict tested as
false even though nfsd_break_one_deleg() ran before ->fi_lock was
unlocked. i.e. while hash_delegation_locked() was running.
As hash_delegation_lock() doesn't interact in any way with nfs4_run_cb()
there can be no importance to this interaction.
So this patch removes the locking from nfsd_break_one_deleg() and moves
the final test on ->fi_had_conflict out of the locked region to make it
clear that locking isn't important to the test. It is still tested
*after* vfs_setlease() has succeeded. This might be significant and as
vfs_setlease() takes ->flc_lock, and nfsd_break_one_deleg() is called
under ->flc_lock this "after" is a true ordering provided by a spinlock.
Fixes: edcf972515 ("nfsd: fix RELEASE_LOCKOWNER")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
HDMI audio can be enabled over AM62A-SK using the same DT overlay that
is used for AM625 / AM62-LP SK-EVMs.
Add the sk.dtb + hdmi-audio.dtbo combination for AM62A7-SK as well, to
check for overlay applicability during DTBS compile tests.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-4-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>