commit 1e9cb763e9 upstream.
The ENA adapters on our instances occasionally reset. Once recently
logged a UBSAN failure to console in the process:
UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117
Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017
Workqueue: ena ena_fw_reset_device [ena]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e
? __const_udelay+0x43/0x50
ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena]
wait_for_reset_state+0x54/0xa0 [ena]
ena_com_dev_reset+0xc8/0x110 [ena]
ena_down+0x3fe/0x480 [ena]
ena_destroy_device+0xeb/0xf0 [ena]
ena_fw_reset_device+0x30/0x50 [ena]
process_one_work+0x22b/0x3d0
worker_thread+0x4d/0x3f0
? process_one_work+0x3d0/0x3d0
kthread+0x12a/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
Apparently, the reset delays are getting so large they can trigger a
UBSAN panic.
Looking at the code, the current timeout is capped at 5000us. Using a
base value of 100us, the current code will overflow after (1<<29). Even
at values before 32, this function wraps around, perhaps
unintentionally.
Cap the value of the exponent used for this backoff at (1<<16) which is
larger than currently necessary, but large enough to support bigger
values in the future.
Cc: stable@vger.kernel.org
Fixes: 4bb7f4cf60 ("net: ena: reduce driver load time")
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20230711013621.GE1926@templeofstupid.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 963b54df82 upstream.
When allocating the 2D array for handling IRQ type registers in
regmap_add_irq_chip_fwnode(), the intent is to allocate a matrix
with num_config_bases rows and num_config_regs columns.
This is currently handled by allocating a buffer to hold a pointer for
each row (i.e. num_config_bases). After that, the logic attempts to
allocate the memory required to hold the register configuration for
each row. However, instead of doing this allocation for each row
(i.e. num_config_bases allocations), the logic erroneously does this
allocation num_config_regs number of times.
This scenario can lead to out-of-bounds accesses when num_config_regs
is greater than num_config_bases. Fix this by updating the terminating
condition of the loop that allocates the memory for holding the register
configuration to allocate memory only for each row in the matrix.
Amit Pundir reported a crash that was occurring on his db845c device
due to memory corruption (see "Closes" tag for Amit's report). The KASAN
report below helped narrow it down to this issue:
[ 14.033877][ T1] ==================================================================
[ 14.042507][ T1] BUG: KASAN: invalid-access in regmap_add_irq_chip_fwnode+0x594/0x1364
[ 14.050796][ T1] Write of size 8 at addr 06ffff8081021850 by task init/1
[ 14.242004][ T1] The buggy address belongs to the object at ffffff8081021850
[ 14.242004][ T1] which belongs to the cache kmalloc-8 of size 8
[ 14.255669][ T1] The buggy address is located 0 bytes inside of
[ 14.255669][ T1] 8-byte region [ffffff8081021850, ffffff8081021858)
Fixes: faa87ce919 ("regmap-irq: Introduce config registers for irq types")
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Closes: https://lore.kernel.org/all/CAMi1Hd04mu6JojT3y6wyN2YeVkPR5R3qnkKJ8iR8if_YByCn4w@mail.gmail.com/
Tested-by: John Stultz <jstultz@google.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # tested on Dragonboard 845c
Cc: stable@vger.kernel.org # v6.0+
Cc: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: "Isaac J. Manjarres" <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20230711193059.2480971-1-isaacmanjarres@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66843b14fb upstream.
Since commit 096b52fd2b ("perf: RISC-V: throttle perf events") the
perf_sample_event_took() function was added to report time spent in
overflow interrupts. If the interrupt takes too long, the perf framework
will lower the sysctl_perf_event_sample_rate and max_samples_per_tick.
When hwc->interrupts is larger than max_samples_per_tick, the
hwc->interrupts will be set to MAX_INTERRUPTS, and events will be
throttled within the __perf_event_account_interrupt() function.
However, the RISC-V PMU driver doesn't call riscv_pmu_stop() to update the
PERF_HES_STOPPED flag after perf_event_overflow() in pmu_sbi_ovf_handler()
function to avoid throttling. When the perf framework unthrottled the event
in the timer interrupt handler, it triggers riscv_pmu_start() function
and causes a WARN_ON_ONCE() warning, as shown below:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 240 at drivers/perf/riscv_pmu.c:184 riscv_pmu_start+0x7c/0x8e
Modules linked in:
CPU: 0 PID: 240 Comm: ls Not tainted 6.4-rc4-g19d0788e9ef2 #1
Hardware name: SiFive (DT)
epc : riscv_pmu_start+0x7c/0x8e
ra : riscv_pmu_start+0x28/0x8e
epc : ffffffff80aef864 ra : ffffffff80aef810 sp : ffff8f80004db6f0
gp : ffffffff81c83750 tp : ffffaf80069f9bc0 t0 : ffff8f80004db6c0
t1 : 0000000000000000 t2 : 000000000000001f s0 : ffff8f80004db720
s1 : ffffaf8008ca1068 a0 : 0000ffffffffffff a1 : 0000000000000000
a2 : 0000000000000001 a3 : 0000000000000870 a4 : 0000000000000000
a5 : 0000000000000000 a6 : 0000000000000840 a7 : 0000000000000030
s2 : 0000000000000000 s3 : ffffaf8005165800 s4 : ffffaf800424da00
s5 : ffffffffffffffff s6 : ffffffff81cc7590 s7 : 0000000000000000
s8 : 0000000000000006 s9 : 0000000000000001 s10: ffffaf807efbc340
s11: ffffaf807efbbf00 t3 : ffffaf8006a16028 t4 : 00000000dbfbb796
t5 : 0000000700000000 t6 : ffffaf8005269870
status: 0000000200000100 badaddr: 0000000000000000 cause: 0000000000000003
[<ffffffff80aef864>] riscv_pmu_start+0x7c/0x8e
[<ffffffff80185b56>] perf_adjust_freq_unthr_context+0x15e/0x174
[<ffffffff80188642>] perf_event_task_tick+0x88/0x9c
[<ffffffff800626a8>] scheduler_tick+0xfe/0x27c
[<ffffffff800b5640>] update_process_times+0x9a/0xba
[<ffffffff800c5bd4>] tick_sched_handle+0x32/0x66
[<ffffffff800c5e0c>] tick_sched_timer+0x64/0xb0
[<ffffffff800b5e50>] __hrtimer_run_queues+0x156/0x2f4
[<ffffffff800b6bdc>] hrtimer_interrupt+0xe2/0x1fe
[<ffffffff80acc9e8>] riscv_timer_interrupt+0x38/0x42
[<ffffffff80090a16>] handle_percpu_devid_irq+0x90/0x1d2
[<ffffffff8008a9f4>] generic_handle_domain_irq+0x28/0x36
After referring other PMU drivers like Arm, Loongarch, Csky, and Mips,
they don't call *_pmu_stop() to update with PERF_HES_STOPPED flag
after perf_event_overflow() function nor do they add PERF_HES_STOPPED
flag checking in *_pmu_start() which don't cause this warning.
Thus, it's recommended to remove this unnecessary check in
riscv_pmu_start() function to prevent this warning.
Signed-off-by: Eric Lin <eric.lin@sifive.com>
Link: https://lore.kernel.org/r/20230710154328.19574-1-eric.lin@sifive.com
Fixes: 096b52fd2b ("perf: RISC-V: throttle perf events")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8564c31587 upstream.
The ftrace-direct-too sample traces the handle_mm_fault function whose
signature changed since the introduction of the sample. Since:
commit bce617edec ("mm: do page fault accounting in handle_mm_fault")
handle_mm_fault now has 4 arguments. Therefore, the sample trampoline
should save 4 argument registers.
s390 saves all argument registers already so it does not need a change
but x86_64 needs an extra push and pop.
This also evolves the signature of the tracing function to make it
mirror the signature of the traced function.
Link: https://lkml.kernel.org/r/20230427140700.625241-2-revest@chromium.org
Cc: stable@vger.kernel.org
Fixes: bce617edec ("mm: do page fault accounting in handle_mm_fault")
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac522fc6c3 upstream.
While duplicate IDs are still very harmful, including the potential to easily
see changing devices in /dev/disk/by-id, it turn out they are extremely
common for cheap end user NVMe devices.
Relax our check for them for so that it doesn't reject the probe on
single-ported PCIe devices, but prints a big warning instead. In doubt
we'd still like to see quirk entries to disable the potential for
changing supposed stable device identifier links, but this will at least
allow users how have two (or more) of these devices to use them without
having to manually add a new PCI ID entry with the quirk through sysfs or
by patching the kernel.
Fixes: 2079f41ec6 ("nvme: check that EUI/GUID/UUID are globally unique")
Cc: stable@vger.kernel.org # 6.0+
Co-developed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6018b585e8 upstream.
Hist triggers can have referenced variables without having direct
variables fields. This can be the case if referenced variables are added
for trigger actions. In this case the newly added references will not
have field variables. Not taking such referenced variables into
consideration can result in a bug where it would be possible to remove
hist trigger with variables being refenced. This will result in a bug
that is easily reproducable like so
$ cd /sys/kernel/tracing
$ echo 'synthetic_sys_enter char[] comm; long id' >> synthetic_events
$ echo 'hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
$ echo 'hist:keys=common_pid.execname,id.syscall:onmatch(raw_syscalls.sys_enter).synthetic_sys_enter($comm, id)' >> events/raw_syscalls/sys_enter/trigger
$ echo '!hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger
[ 100.263533] ==================================================================
[ 100.264634] BUG: KASAN: slab-use-after-free in resolve_var_refs+0xc7/0x180
[ 100.265520] Read of size 8 at addr ffff88810375d0f0 by task bash/439
[ 100.266320]
[ 100.266533] CPU: 2 PID: 439 Comm: bash Not tainted 6.5.0-rc1 #4
[ 100.267277] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
[ 100.268561] Call Trace:
[ 100.268902] <TASK>
[ 100.269189] dump_stack_lvl+0x4c/0x70
[ 100.269680] print_report+0xc5/0x600
[ 100.270165] ? resolve_var_refs+0xc7/0x180
[ 100.270697] ? kasan_complete_mode_report_info+0x80/0x1f0
[ 100.271389] ? resolve_var_refs+0xc7/0x180
[ 100.271913] kasan_report+0xbd/0x100
[ 100.272380] ? resolve_var_refs+0xc7/0x180
[ 100.272920] __asan_load8+0x71/0xa0
[ 100.273377] resolve_var_refs+0xc7/0x180
[ 100.273888] event_hist_trigger+0x749/0x860
[ 100.274505] ? kasan_save_stack+0x2a/0x50
[ 100.275024] ? kasan_set_track+0x29/0x40
[ 100.275536] ? __pfx_event_hist_trigger+0x10/0x10
[ 100.276138] ? ksys_write+0xd1/0x170
[ 100.276607] ? do_syscall_64+0x3c/0x90
[ 100.277099] ? entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.277771] ? destroy_hist_data+0x446/0x470
[ 100.278324] ? event_hist_trigger_parse+0xa6c/0x3860
[ 100.278962] ? __pfx_event_hist_trigger_parse+0x10/0x10
[ 100.279627] ? __kasan_check_write+0x18/0x20
[ 100.280177] ? mutex_unlock+0x85/0xd0
[ 100.280660] ? __pfx_mutex_unlock+0x10/0x10
[ 100.281200] ? kfree+0x7b/0x120
[ 100.281619] ? ____kasan_slab_free+0x15d/0x1d0
[ 100.282197] ? event_trigger_write+0xac/0x100
[ 100.282764] ? __kasan_slab_free+0x16/0x20
[ 100.283293] ? __kmem_cache_free+0x153/0x2f0
[ 100.283844] ? sched_mm_cid_remote_clear+0xb1/0x250
[ 100.284550] ? __pfx_sched_mm_cid_remote_clear+0x10/0x10
[ 100.285221] ? event_trigger_write+0xbc/0x100
[ 100.285781] ? __kasan_check_read+0x15/0x20
[ 100.286321] ? __bitmap_weight+0x66/0xa0
[ 100.286833] ? _find_next_bit+0x46/0xe0
[ 100.287334] ? task_mm_cid_work+0x37f/0x450
[ 100.287872] event_triggers_call+0x84/0x150
[ 100.288408] trace_event_buffer_commit+0x339/0x430
[ 100.289073] ? ring_buffer_event_data+0x3f/0x60
[ 100.292189] trace_event_raw_event_sys_enter+0x8b/0xe0
[ 100.295434] syscall_trace_enter.constprop.0+0x18f/0x1b0
[ 100.298653] syscall_enter_from_user_mode+0x32/0x40
[ 100.301808] do_syscall_64+0x1a/0x90
[ 100.304748] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[ 100.307775] RIP: 0033:0x7f686c75c1cb
[ 100.310617] Code: 73 01 c3 48 8b 0d 65 3c 10 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 21 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 3c 10 00 f7 d8 64 89 01 48
[ 100.317847] RSP: 002b:00007ffc60137a38 EFLAGS: 00000246 ORIG_RAX: 0000000000000021
[ 100.321200] RAX: ffffffffffffffda RBX: 000055f566469ea0 RCX: 00007f686c75c1cb
[ 100.324631] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 000000000000000a
[ 100.328104] RBP: 00007ffc60137ac0 R08: 00007f686c818460 R09: 000000000000000a
[ 100.331509] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000009
[ 100.334992] R13: 0000000000000007 R14: 000000000000000a R15: 0000000000000007
[ 100.338381] </TASK>
We hit the bug because when second hist trigger has was created
has_hist_vars() returned false because hist trigger did not have
variables. As a result of that save_hist_vars() was not called to add
the trigger to trace_array->hist_vars. Later on when we attempted to
remove the first histogram find_any_var_ref() failed to detect it is
being used because it did not find the second trigger in hist_vars list.
With this change we wait until trigger actions are created so we can take
into consideration if hist trigger has variable references. Also, now we
check the return value of save_hist_vars() and fail trigger creation if
save_hist_vars() fails.
Link: https://lore.kernel.org/linux-trace-kernel/20230712223021.636335-1-mkhalfella@purestorage.com
Cc: stable@vger.kernel.org
Fixes: 067fe038e7 ("tracing: Add variable reference handling to hist triggers")
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47f04616f2 upstream.
Add a NULL check for the 'bdev' parameter of
dm_verity_loadpin_is_bdev_trusted(). The function is called
by loadpin_check(), which passes the block device that
corresponds to the super block of the file system from which
a file is being loaded. Generally a super_block structure has
an associated block device, however that is not always the
case (e.g. tmpfs).
Cc: stable@vger.kernel.org # v6.0+
Fixes: b6c1c5745c ("dm: Add verity helpers for LoadPin")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230627202800.1.Id63f7f59536d20f1ab83e1abdc1fda1471c7d031@changeid
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938f0c35d7 upstream.
Nathan Chancellor reported a kernel build error on Fedora 39:
$ clang --version | head -1
clang version 16.0.5 (Fedora 16.0.5-1.fc39)
$ s390x-linux-gnu-ld --version | head -1
GNU ld version 2.40-1.fc39
$ make -skj"$(nproc)" ARCH=s390 CC=clang CROSS_COMPILE=s390x-linux-gnu- olddefconfig all
s390x-linux-gnu-ld: arch/s390/boot/startup.o(.text+0x5b4): misaligned symbol `_decompressor_end' (0x35b0f) for relocation R_390_PC32DBL
make[3]: *** [.../arch/s390/boot/Makefile:78: arch/s390/boot/vmlinux] Error 1
It turned out that the problem with misaligned symbols on s390 was fixed
with commit 80ddf5ce1c ("s390: always build relocatable kernel") for the
kernel image, but did not take into account that the decompressor uses its
own set of CFLAGS, which come without -fPIE.
Add the -fPIE flag also to the decompresser CFLAGS to fix this.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: CKI <cki-project@redhat.com>
Suggested-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1747
Link: https://lore.kernel.org/32935.123062114500601371@us-mta-9.us.mimecast.lan/
Link: https://lore.kernel.org/r/20230622125508.1068457-1-hca@linux.ibm.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82d62f708 upstream.
This reverts commit eb26dfe8aa.
Commit eb26dfe8aa ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.
In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.
Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.
Fixes: eb26dfe8aa ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 950e9a295b upstream.
The value of the V4L2_SUBDEV_ROUTE_FL_ACTIVE is 1, not 0. Use hexadecimal
numbers as is done elsewhere in the documentation.
Cc: stable@vger.kernel.org # for >= v6.3
Fixes: ea73eda508 ("media: Documentation: Add GS_ROUTING documentation")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 490937d479 upstream.
The 'qcom_swrm_ctrl->pconfig' has size of QCOM_SDW_MAX_PORTS (14),
however we index it starting from 1, not 0, to match real port numbers.
This can lead to writing port config past 'pconfig' bounds and
overwriting next member of 'qcom_swrm_ctrl' struct. Reported also by
smatch:
drivers/soundwire/qcom.c:1269 qcom_swrm_get_port_config() error: buffer overflow 'ctrl->pconfig' 14 <= 14
Fixes: 9916c02ccd ("soundwire: qcom: cleanup internal port config indexing")
Cc: <stable@vger.kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202305201301.sCJ8UDKV-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601102525.609627-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2a2ab039b upstream.
When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns
-EPROBE_DEFER, the opp_table is freed again, to wait until all the
interconnect paths are available.
However, if the OPP table is using required-opps then it may already
have been added to the global lazy_opp_tables list. The error path
does not remove the opp_table from the list again.
This can cause crashes later when the provider of the required-opps
is added, since we will iterate over OPP tables that have already been
freed. E.g.:
Unable to handle kernel NULL pointer dereference when read
CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3
PC is at _of_add_opp_table_v2 (include/linux/of.h:949
drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404
drivers/opp/of.c:1032) -> lazy_link_required_opp_table()
Fix this by calling _of_clear_opp_table() to remove the opp_table from
the list and clear other allocated resources. While at it, also add the
missing mutex_destroy() calls in the error path.
Cc: stable@vger.kernel.org
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Fixes: 7eba0c7641 ("opp: Allow lazy-linking of required-opps")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c57fa00370 upstream.
According to the datasheets of supported meson SoCs length of ADC_CLK_DIV
field is 6-bit. Although all supported SoCs have the register
with that field documented later SoCs use external clock rather than
ADC internal clock so this patch affects only meson8 family (S8* SoCs).
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230606165357.42417-1-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b0328d0b upstream.
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a865a6522 upstream.
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f927728186 upstream.
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6df696cd9b upstream.
AmpereOne has an erratum in its implementation of FEAT_HAFDBS that
required disabling the feature on the design. This was done by reporting
the feature as not implemented in the ID register, although the
corresponding control bits were not actually RES0. This does not align
well with the requirements of the architecture, which mandates these
bits be RES0 if HAFDBS isn't implemented.
The kernel's use of stage-1 is unaffected, as the HA and HD bits are
only set if HAFDBS is detected in the ID register. KVM, on the other
hand, relies on the RES0 behavior at stage-2 to use the same value for
VTCR_EL2 on any cpu in the system. Mitigate the non-RES0 behavior by
leaving VTCR_EL2.HA clear on affected systems.
Cc: stable@vger.kernel.org
Cc: D Scott Phillips <scott@os.amperecomputing.com>
Cc: Darren Hart <darren@os.amperecomputing.com>
Acked-by: D Scott Phillips <scott@os.amperecomputing.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20230609220104.1836988-2-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc7eab25b1 upstream.
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port.
Fixes: e20aa071cd ("nfp: fix schedule in atomic context when sync mc address")
Cc: stable@vger.kernel.org
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Message-ID: <20230705052818.7122-1-louis.peens@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 257e6172ab upstream.
If a client sends out a cap update dropping caps with the prior 'seq'
just before an incoming cap revoke request, then the client may drop
the revoke because it believes it's already released the requested
capabilities.
This causes the MDS to wait indefinitely for the client to respond
to the revoke. It's therefore always a good idea to ack the cap
revoke request with the bumped up 'seq'.
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/61782
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Reviewed-by: Patrick Donnelly <pdonnell@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc94bb8f27 upstream.
Blindly expanding the readahead windows will cause unneccessary
pagecache thrashing and also will introduce the network workload.
We should disable expanding the windows if the readahead is disabled
and also shouldn't expand the windows too much.
Expanding forward firstly instead of expanding backward for possible
sequential reads.
Bound `rreq->len` to the actual file size to restore the previous page
cache usage.
The posix_fadvise may change the maximum size of a file readahead.
Cc: stable@vger.kernel.org
Fixes: 4987005600 ("ceph: convert ceph_readpages to ceph_readahead")
Link: https://lore.kernel.org/ceph-devel/20230504082510.247-1-sehuww@mail.scut.edu.cn
Link: https://www.spinics.net/lists/ceph-users/msg76183.html
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-and-tested-by: Hu Weiwen <sehuww@mail.scut.edu.cn>
Reviewed-by: Milind Changire <mchangir@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a282a2f105 upstream.
ceph_frame_desc::fd_lens is an int array. decode_preamble() thus
effectively casts u32 -> int but the checks for segment lengths are
written as if on unsigned values. While reading in HELLO or one of the
AUTH frames (before authentication is completed), arithmetic in
head_onwire_len() can get duped by negative ctrl_len and produce
head_len which is less than CEPH_PREAMBLE_LEN but still positive.
This would lead to a buffer overrun in prepare_read_control() as the
preamble gets copied to the newly allocated buffer of size head_len.
Cc: stable@vger.kernel.org
Fixes: cd1a677cad ("libceph, ceph: implement msgr2.1 protocol (crc and secure modes)")
Reported-by: Thelford Williams <thelford@google.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1995f15590 upstream.
svc_create_memory_pool() is only called from stratix10_svc_drv_probe().
Most of resources in the probe are managed, but not this memremap() call.
There is also no memunmap() call in the file.
So switch to devm_memremap() to avoid a resource leak.
Cc: stable@vger.kernel.org
Fixes: 7ca5ce8965 ("firmware: add Intel Stratix10 service layer driver")
Link: https://lore.kernel.org/all/783e9dfbba34e28505c9efa8bba41f97fd0fa1dc.1686109400.git.christophe.jaillet@wanadoo.fr/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Message-ID: <20230613211521.16366-1-dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4903fde804 upstream.
It is possible to hang pty devices in this case, the reader was
blocking at epoll on master side, the writer was sleeping at
wait_woken inside n_tty_write on slave side, and the write buffer
on tty_port was full, we found that the reader and writer would
never be woken again and blocked forever.
The problem was caused by a race between reader and kworker:
n_tty_read(reader): n_tty_receive_buf_common(kworker):
copy_from_read_buf()|
|room = N_TTY_BUF_SIZE - (ldata->read_head - tail)
|room <= 0
n_tty_kick_worker() |
|ldata->no_room = true
After writing to slave device, writer wakes up kworker to flush
data on tty_port to reader, and the kworker finds that reader
has no room to store data so room <= 0 is met. At this moment,
reader consumes all the data on reader buffer and calls
n_tty_kick_worker to check ldata->no_room which is false and
reader quits reading. Then kworker sets ldata->no_room=true
and quits too.
If write buffer is not full, writer will wake kworker to flush data
again after following writes, but if write buffer is full and writer
goes to sleep, kworker will never be woken again and tty device is
blocked.
This problem can be solved with a check for read buffer size inside
n_tty_receive_buf_common, if read buffer is empty and ldata->no_room
is true, a call to n_tty_kick_worker is necessary to keep flushing
data to reader.
Cc: <stable@vger.kernel.org>
Fixes: 42458f41d0 ("n_tty: Ensure reader restarts worker for next reader")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Hui Li <caelli@tencent.com>
Message-ID: <1680749090-14106-1-git-send-email-caelli@tencent.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 639949a703 upstream.
Since commit 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal
active high") RS485 reception no longer works after a transmission.
The following scenario shows the problem:
1) Open a port in RS485 mode
2) Receive data from remote (OK)
3) Transmit data to remote (OK)
4) Receive data from remote (Nothing received)
In RS485 mode, imx_uart_start_tx() calls imx_uart_stop_rx() and, when the
transmission is complete, imx_uart_stop_tx() calls imx_uart_start_rx().
Since the above commit imx_uart_stop_rx() now sets the loopback bit but
imx_uart_start_rx() does not clear it causing the hardware to remain in
loopback mode and not receive external data.
Fix this by moving the existing loopback disable code to a helper function
and calling it from imx_uart_start_rx() too.
Fixes: 79d0224f6b ("tty: serial: imx: Handle RS485 DE signal active high")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230616104838.2729694-1-martin.fuzzey@flowbird.group
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 832e231cff upstream.
When the best clk is searched, we iterate over all possible clk.
If we find a better match, the previous one, if any, needs to be freed.
If a better match has already been found, we still need to free the new
one, otherwise it leaks.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <cf3e0053d2fc7391b2d906a86cd01a5ef15fb9dc.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9c09546e9 upstream.
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed.
Cc: <stable@vger.kernel.org> # v3.3+
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Fixes: 5f5a7a5578 ("serial: samsung: switch to clkdev based clock lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Message-ID: <e4baf6039368f52e5a5453982ddcb9a330fc689e.1686412569.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27a826837e upstream.
The atmel_complete_tx_dma() function disables IRQs at the start
of the function by calling spin_lock_irqsave(&port->lock, flags);
There is no need to disable them a second time using the
spin_lock_irq() function and, in fact, doing so is a bug because
it will enable IRQs prematurely when we call spin_unlock_irq().
Just use spin_lock/unlock() instead without disabling or enabling
IRQs.
Fixes: 08f738be88 ("serial: at91: add tx dma support")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/cb7c39a9-c004-4673-92e1-be4e34b85368@moroto.mountain
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a590f03d8d upstream.
If moving the bo to system for swapout failed, we were leaking
a resource. Fix.
Fixes: bfa3357ef9 ("drm/ttm: allocate resource object instead of embedding it v2")
Cc: Christian König <christian.koenig@amd.com>
Cc: "Christian König" <ckoenig.leichtzumerken@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230626091450.14757-5-thomas.hellstrom@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d934e537c1 upstream.
the smu driver_table is used for all types of smu
tables data transcation (e.g: PPtable, Metrics, i2c, Ecc..).
it is necessary to hold this lock to avoiding data tampering
during the i2c read operation.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a774fe912 upstream.
In restore process worker, pinned BO cause update PTE fail, then
the function re-schedule the restore_work. This will generate dead loop.
Signed-off-by: gaba <gaba@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 613a7956de upstream.
Disable FAMS on a Samsung Odyssey G9 monitor. Experiments show that this
monitor does not work well under some use cases, and is likely
implementation specific bug on the monitor's firmware.
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 274d205cb5 upstream.
The `DMUB_FW_VERSION` macro has a mistake in that the revision field
is off by one byte. The last byte is typically used for other purposes
and not a revision.
Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Cc: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed83fe2abc upstream.
[Why]
We don't check 128b132b-specific bits in LANE_ALIGN_STATUS_UPDATED DPCD
registers when parsing link loss status, which can cause us to miss a
link loss notification from some sinks.
[How]
Add a 128b132b-specific status bit check.
Cc: stable@vger.kernel.org # 6.3+
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f48a4b836 upstream.
[Why & How]
We have to check if stream is properly initialized before calling
find_matching_pll(), otherwise we might end up trying to deferecence a
NULL pointer.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 072030b178 upstream.
A number of users have reported that there are random hangs occurring
caused by PSR-SU specifically on panels that contain the parade 0803
TCON. Users have been able to work around the issue by disabling PSR
entirely.
To avoid these hangs, disable PSR-SU when this TCON is found.
Cc: stable@vger.kernel.org
Cc: Sean Wang <sean.ns.wang@amd.com>
Cc: Marc Rossi <Marc.Rossi@amd.com>
Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com>
Suggested-by: Tsung-hua (Ryan) Lin <Tsung-hua.Lin@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2443
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea2c3c0855 upstream.
Per VM BOs must be marked as moved or otherwise their ranges are not
updated on use which might be necessary when the replace operation
splits mappings.
This fixes random GPU hangs when replacing sparse mappings from the
userspace, while OP_MAP/OP_UNMAP works fine because always valid BOs
are correctly handled there.
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26518b3918 upstream.
[Why & How]
Having seamless boot on while forcing debug option ODM combine 2 to 1
will cause some corruptions because of some missing programmings.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1966bbfdfe upstream.
[Why]
K1 and K2 not being setting properly when subVP is active.
[How]
Have phantom pipes use the same programing as the main pipes without
checking the paired stream
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Austin Zheng <austin.zheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a0e005c79 upstream.
[Why] most edp support only timings from edid. applying
non-edid timings, especially those timings out of edp
bandwidth, may damage edp.
[How] do not add non-edid timings for edp.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f477c7b5ec upstream.
[Why & How]
We need to store CRTC information in secure_display_ctx, so postpone
the call to amdgpu_dm_crtc_secure_display_create_contexts() until we
initialize all CRTCs.
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee7be8f3de upstream.
- Due to hardware related QoS issues, we need to limit certain
SKUs with less memory channels to DPM1 and above.
- At DPM0 + workload running, the urgent return latency can
exceed 15us (the expected maximum is 4us) which results in underflow
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72f1de49ff upstream.
[Why]
The sequence for collecting down_reply from source perspective should
be:
Request_n->repeat (get partial reply of Request_n->clear message ready
flag to ack DPRX that the message is received) till all partial
replies for Request_n are received->new Request_n+1.
Now there is chance that drm_dp_mst_hpd_irq() will fire new down
request in the tx queue when the down reply is incomplete. Source is
restricted to generate interveleaved message transactions so we should
avoid it.
Also, while assembling partial reply packets, reading out DPCD DOWN_REP
Sideband MSG buffer + clearing DOWN_REP_MSG_RDY flag should be
wrapped up as a complete operation for reading out a reply packet.
Kicking off a new request before clearing DOWN_REP_MSG_RDY flag might
be risky. e.g. If the reply of the new request has overwritten the
DPRX DOWN_REP Sideband MSG buffer before source writing one to clear
DOWN_REP_MSG_RDY flag, source then unintentionally flushes the reply
for the new request. Should handle the up request in the same way.
[How]
Separete drm_dp_mst_hpd_irq() into 2 steps. After acking the MST IRQ
event, driver calls drm_dp_mst_hpd_irq_send_new_request() and might
trigger drm_dp_mst_kick_tx() only when there is no on going message
transaction.
Changes since v1:
* Reworked on review comments received
-> Adjust the fix to let driver explicitly kick off new down request
when mst irq event is handled and acked
-> Adjust the commit message
Changes since v2:
* Adjust the commit message
* Adjust the naming of the divided 2 functions and add a new input
parameter "ack".
* Adjust code flow as per review comments.
Changes since v3:
* Update the function description of drm_dp_mst_hpd_irq_handle_event
Changes since v4:
* Change ack of drm_dp_mst_hpd_irq_handle_event() to be an array align
the size of esi[]
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bdba9d4a3 upstream.
If we disable vblank when entering self-refresh, vblank APIs (like
DRM_IOCTL_WAIT_VBLANK) no longer work. But user space is not aware when
we enter self-refresh, so this appears to be an API violation -- that
DRM_IOCTL_WAIT_VBLANK fails with EINVAL whenever the display is idle and
enters self-refresh.
The downstream driver used by many of these systems never used to
disable vblank for PSR, and in fact, even upstream, we didn't do that
until radically redesigning the state machine in commit 6c836d965b
("drm/rockchip: Use the helpers for PSR").
Thus, it seems like a reasonable API fix to simply restore that
behavior, and leave vblank enabled.
Note that this appears to potentially unbalance the
drm_crtc_vblank_{off,on}() calls in some cases, but:
(a) drm_crtc_vblank_on() documents this as OK and
(b) if I do the naive balancing, I find state machine issues such that
we're not in sync properly; so it's easier to take advantage of (a).
This issue was exposed by IGT's kms_vblank tests, and reported by
KernelCI. The bug has been around a while (longer than KernelCI
noticed), but was only exposed once self-refresh was bugfixed more
recently, and so KernelCI could properly test it. Some other notes in:
https://lore.kernel.org/dri-devel/Y6OCg9BPnJvimQLT@google.com/
Re: renesas/master bisection: igt-kms-rockchip.kms_vblank.pipe-A-wait-forked on rk3399-gru-kevin
== Backporting notes: ==
Marking as 'Fixes' commit 6c836d965b ("drm/rockchip: Use the helpers
for PSR"), but it probably depends on commit bed030a49f
("drm/rockchip: Don't fully disable vop on self refresh") as well.
We also need the previous patch ("drm/atomic: Allow vblank-enabled +
self-refresh "disable""), of course.
v3:
* no update
v2:
* skip unnecessary lock/unlock
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Link: https://lore.kernel.org/dri-devel/Y5itf0+yNIQa6fU4@sirena.org.uk/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.2.Ic07cba4ab9a7bd3618a9e4258b8f92ea7d10ae5a@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d0e3cac35 upstream.
The self-refresh helper framework overloads "disable" to sometimes mean
"go into self-refresh mode," and this mode activates automatically
(e.g., after some period of unchanging display output). In such cases,
the display pipe is still considered "on", and user-space is not aware
that we went into self-refresh mode. Thus, users may expect that
vblank-related features (such as DRM_IOCTL_WAIT_VBLANK) still work
properly.
However, we trigger the WARN_ONCE() here if a CRTC driver tries to leave
vblank enabled.
Add a different expectation: that CRTCs *should* leave vblank enabled
when going into self-refresh.
This patch is preparation for another patch -- "drm/rockchip: vop: Leave
vblank enabled in self-refresh" -- which resolves conflicts between the
above self-refresh behavior and the API tests in IGT's kms_vblank test
module.
== Some alternatives discussed: ==
It's likely that on many display controllers, vblank interrupts will
turn off when the CRTC is disabled, and so in some cases, self-refresh
may not support vblank. To support such cases, we might consider
additions to the generic helpers such that we fire vblank events based
on a timer.
However, there is currently only one driver using the common
self-refresh helpers (i.e., rockchip), and at least as of commit
bed030a49f ("drm/rockchip: Don't fully disable vop on self refresh"),
the CRTC hardware is powered enough to continue to generate vblank
interrupts.
So we chose the simpler option of leaving vblank interrupts enabled. We
can reevaluate this decision and perhaps augment the helpers if/when we
gain a second driver that has different requirements.
v3:
* include discussion summary
v2:
* add 'ret != 0' warning case for self-refresh
* describe failing test case and relation to drm/rockchip patch better
Cc: <stable@vger.kernel.org> # dependency for "drm/rockchip: vop: Leave
# vblank enabled in self-refresh"
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230109171809.v3.1.I3904f697863649eb1be540ecca147a66e42bfad7@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97f975823f upstream.
Smatch detected a double free path because lpfc_nlp_not_used() releases an
ndlp object before reaching lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc().
Remove the outdated lpfc_nlp_not_used() routine. In
lpfc_mbx_cmpl_ns_reg_login(), replace the call with lpfc_nlp_put(). In
lpfc_cmpl_els_logo_acc(), replace the call with lpfc_unreg_rpi() and keep
the lpfc_nlp_put() at the end of the routine. If ndlp's rpi was
registered, then lpfc_unreg_rpi()'s completion routine performs the final
ndlp clean up after lpfc_nlp_put() is called from lpfc_cmpl_els_logo_acc().
Otherwise if ndlp has no rpi registered, the lpfc_nlp_put() at the end of
lpfc_cmpl_els_logo_acc() is the final ndlp clean up.
Fixes: 4430f7fd09 ("scsi: lpfc: Rework locations of ndlp reference taking")
Cc: <stable@vger.kernel.org> # v5.11+
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/Y3OefhyyJNKH%2Fiaf@kili/
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230417191558.83100-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
