[ Upstream commit 5a50f2b611 ]
The rkisp1_flt_config() function performs an initial direct write to
RKISP1_CIF_ISP_FILT_MODE without including the RKISP1_CIF_ISP_FLT_ENA
bit, which clears the filter enable bit in the hardware.
The subsequent read/modify/write sequence then reads back the register
with the enable bit already cleared and cannot restore it, resulting in
the filter being inadvertently disabled.
Remove the redundant direct write. The read/modify/write sequence alone
correctly preserves the existing enable bit state while updating the
DNR mode and filter configuration bits.
Signed-off-by: Rui Wang <rui.wang@ideasonboard.com>
Reviewed-by: Stefan Klug <stefan.klug@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patch.msgid.link/20260105171142.147792-2-rui.wang@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc84778723 ]
The atmel_hlcdc_plane_atomic_duplicate_state() callback was copying
the atmel_hlcdc_plane state structure without properly duplicating the
drm_plane_state. In particular, state->commit remained set to the old
state commit, which can lead to a use-after-free in the next
drm_atomic_commit() call.
Fix this by calling
__drm_atomic_helper_duplicate_plane_state(), which correctly clones
the base drm_plane_state (including the ->commit pointer).
It has been seen when closing and re-opening the device node while
another DRM client (e.g. fbdev) is still attached:
=============================================================================
BUG kmalloc-64 (Not tainted): Poison overwritten
-----------------------------------------------------------------------------
0xc611b344-0xc611b344 @offset=836. First byte 0x6a instead of 0x6b
FIX kmalloc-64: Restoring Poison 0xc611b344-0xc611b344=0x6b
Allocated in drm_atomic_helper_setup_commit+0x1e8/0x7bc age=178 cpu=0
pid=29
drm_atomic_helper_setup_commit+0x1e8/0x7bc
drm_atomic_helper_commit+0x3c/0x15c
drm_atomic_commit+0xc0/0xf4
drm_framebuffer_remove+0x4cc/0x5a8
drm_mode_rmfb_work_fn+0x6c/0x80
process_one_work+0x12c/0x2cc
worker_thread+0x2a8/0x400
kthread+0xc0/0xdc
ret_from_fork+0x14/0x28
Freed in drm_atomic_helper_commit_hw_done+0x100/0x150 age=8 cpu=0
pid=169
drm_atomic_helper_commit_hw_done+0x100/0x150
drm_atomic_helper_commit_tail+0x64/0x8c
commit_tail+0x168/0x18c
drm_atomic_helper_commit+0x138/0x15c
drm_atomic_commit+0xc0/0xf4
drm_atomic_helper_set_config+0x84/0xb8
drm_mode_setcrtc+0x32c/0x810
drm_ioctl+0x20c/0x488
sys_ioctl+0x14c/0xc20
ret_fast_syscall+0x0/0x54
Slab 0xef8bc360 objects=21 used=16 fp=0xc611b7c0
flags=0x200(workingset|zone=0)
Object 0xc611b340 @offset=832 fp=0xc611b7c0
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Link: https://patch.msgid.link/20251024-lcd_fixes_mainlining-v1-2-79b615130dc3@microchip.com
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06682206e2 ]
Don’t reject the commit when the source rectangle has fractional parts.
This can occur due to scaling: drm_atomic_helper_check_plane_state() calls
drm_rect_clip_scaled(), which may introduce fractional parts while
computing the clipped source rectangle. This does not imply the commit is
invalid, so we should accept it instead of discarding it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Link: https://patch.msgid.link/20251120-lcd_scaling_fix-v1-1-5ffc98557923@microchip.com
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f123524710 ]
After several commits, the slab memory increases. Some drm_crtc_commit
objects are not freed. The atomic_destroy_state callback only put the
framebuffer. Use the __drm_atomic_helper_plane_destroy_state() function
to put all the objects that are no longer needed.
It has been seen after hours of usage of a graphics application or using
kmemleak:
unreferenced object 0xc63a6580 (size 64):
comm "egt_basic", pid 171, jiffies 4294940784
hex dump (first 32 bytes):
40 50 34 c5 01 00 00 00 ff ff ff ff 8c 65 3a c6 @P4..........e:.
8c 65 3a c6 ff ff ff ff 98 65 3a c6 98 65 3a c6 .e:......e:..e:.
backtrace (crc c25aa925):
kmemleak_alloc+0x34/0x3c
__kmalloc_cache_noprof+0x150/0x1a4
drm_atomic_helper_setup_commit+0x1e8/0x7bc
drm_atomic_helper_commit+0x3c/0x15c
drm_atomic_commit+0xc0/0xf4
drm_atomic_helper_set_config+0x84/0xb8
drm_mode_setcrtc+0x32c/0x810
drm_ioctl+0x20c/0x488
sys_ioctl+0x14c/0xc20
ret_fast_syscall+0x0/0x54
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Link: https://patch.msgid.link/20251024-lcd_fixes_mainlining-v1-1-79b615130dc3@microchip.com
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cee62904c ]
[why & how]
VBIOS DMCUB FW can enable FEC for capable eDPs, but S/W DC state is
only updated for link0 when transitioning into OS with driver loaded.
This causes issues when the eDP is immediately hidden and DIG0 is
assigned to another link that does not support FEC. Driver will
attempt to disable FEC but FEC enablement occurs based on the link
state, which does not have fec_state updated since it is a different
link. Thus, FEC disablement on DIG0 will get skipped and cause no
light up.
Reviewed-by: Karen Chen <karen.chen@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b190870e0e ]
Add Nova Lake (NVL) audio Device ID
The ID will be used by HDA legacy, SOF audio stack and the driver
to determine which audio stack should be used (intel-dsp-config).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20260120193507.14019-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08c0989996 ]
rt722 is aggregated with rt1320 amp in arl_rt722_l0_rt1320_l2 and it is
the only audio configuration in the ARL platform. Set .aggregated = 1 to
represent the fact and avoid unexpected issue.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20260119091749.1752088-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c25d01e1c4 ]
The unpacked unions within a packed struct generates alignment warnings
on clang for 32-bit ARM:
./usr/include/linux/vbox_vmmdev_types.h:239:4: error: field u within 'struct vmmdev_hgcm_function_parameter32'
is less aligned than 'union (unnamed union at ./usr/include/linux/vbox_vmmdev_types.h:223:2)'
and is usually due to 'struct vmmdev_hgcm_function_parameter32' being packed,
which can lead to unaligned accesses [-Werror,-Wunaligned-access]
239 | } u;
| ^
./usr/include/linux/vbox_vmmdev_types.h:254:6: error: field u within
'struct vmmdev_hgcm_function_parameter64::(anonymous union)::(unnamed at ./usr/include/linux/vbox_vmmdev_types.h:249:3)'
is less aligned than 'union (unnamed union at ./usr/include/linux/vbox_vmmdev_types.h:251:4)' and is usually due to
'struct vmmdev_hgcm_function_parameter64::(anonymous union)::(unnamed at ./usr/include/linux/vbox_vmmdev_types.h:249:3)'
being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
With the recent changes to compile-test the UAPI headers in more cases,
these warning in combination with CONFIG_WERROR breaks the build.
Fix the warnings.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512140314.DzDxpIVn-lkp@intel.com/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://lore.kernel.org/linux-kbuild/20260110-uapi-test-disable-headers-arm-clang-unaligned-access-v1-1-b7b0fa541daa@kernel.org/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-kbuild/29b2e736-d462-45b7-a0a9-85f8d8a3de56@app.fastmail.com/
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Tested-by: Nicolas Schier <nsc@kernel.org>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/20260115-kbuild-alignment-vbox-v1-2-076aed1623ff@linutronix.de
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26b4309a3a ]
DRM_IOCTL_MODE_CREATEPROPBLOB allows userspace to allocate arbitrary-sized
property blobs backed by kernel memory.
Currently, the blob data allocation is not accounted to the allocating
process's memory cgroup, allowing unprivileged users to trigger unbounded
kernel memory consumption and potentially cause system-wide OOM.
Mark the property blob data allocation with GFP_KERNEL_ACCOUNT so that the memory
is properly charged to the caller's memcg. This ensures existing cgroup
memory limits apply and prevents uncontrolled kernel memory growth without
introducing additional policy or per-file limits.
Signed-off-by: Xiao Kan <814091656@qq.com>
Signed-off-by: Xiao Kan <xiao.kan@samsung.com>
Link: https://patch.msgid.link/tencent_D12AA2DEDE6F359E1AF59405242FB7A5FD05@qq.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c16000166 ]
In svm_migrate_gart_map(), while migrating GART mapping, the number of
bytes copied for the GART table only accounts for CPU pages. On non-4K
systems, each CPU page can contain multiple GPU pages, and the GART
requires one 8-byte PTE per GPU page. As a result, an incorrect size was
passed to the DMA, causing only a partial update of the GART table.
Fix this function to work correctly on non-4K page-size systems by
accounting for the number of GPU pages per CPU page when calculating the
number of bytes to be copied.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Donet Tom <donettom@linux.ibm.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42ea9cf2f1 ]
HW-supported EOP buffer sizes are 4K and 32K. On systems that do not
use 4K pages, the minimum buffer object (BO) allocation size is
PAGE_SIZE (for example, 64K). During queue buffer acquisition, the driver
currently checks the allocated BO size against the supported EOP buffer
size. Since the allocated BO is larger than the expected size, this check
fails, preventing queue creation.
Relax the strict size validation and allow PAGE_SIZE-sized BOs to be used.
Only the required 4K region of the buffer will be used as the EOP buffer
and avoids queue creation failures on non-4K page systems.
Acked-by: Christian König <christian.koenig@amd.com>
Suggested-by: Philip Yang <yangp@amd.com>
Signed-off-by: Donet Tom <donettom@linux.ibm.com>
Signed-off-by: Felix Kuehling <felix.kuehling@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72919c57a0 ]
HP Victus 16-e0xxx with ALC245 codec does not handle the toggling of
the mute LED.
This patch adds a quirk entry for subsystem ID 0x88eb using a new
ALC245_FIXUP_HP_MUTE_LED_V2_COEFBIT fixup, enabling correct mute LED
behavior.
Signed-off-by: Bharat Dev Burman <bharat.singh7924@gmail.com>
Link: https://patch.msgid.link/20260112184253.33376-1-bharat.singh7924@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b08b7007e ]
Close the firmware stream even when disabling a stream on an upstream
sub-device fails. This allows the firmware to release resources related to
a stream that is stopped in any case.
Suggested-by: Bingbu Cao <bingbu.cao@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Tested-by: Mehdi Djait <mehdi.djait@linux.intel.com> # Dell XPS 9315
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5925a92cc7 ]
When enabling streaming fails, the stream is stopped in firmware but not
closed. Do this to release resources on firmware side.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Tested-by: Mehdi Djait <mehdi.djait@linux.intel.com> # Dell XPS 9315
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 779bdaad2a ]
The ipu6 isys driver maintains the list of video buffer queues related to
a stream (in ipu6 context streams on the same CSI-2 virtual channel) and
this list is modified through VIDIOC_STREAMON and VIDIOC_STREAMOFF IOCTLs.
Ensure the common mutex is acquired when accessing the linked list, i.e.
the isys device context's stream_mutex.
Add a lockdep assert to ipu6_isys_get_buffer_list() and switch to guard()
while at it as the error handling becomes more simple this way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 437e1f6a96 ]
With IPU# bridges, endpoints may only be created when the IPU bridge is
initialized. This may happen after the sensor driver's first probe().
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84359d0a5e ]
mt9m114_probe() requests the reset GPIO in output low state:
sensor->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
and then almost immediately afterwards calls mt9m114_power_on() which does:
gpiod_set_value(sensor->reset, 1);
fsleep(duration);
gpiod_set_value(sensor->reset, 0);
which means that if the reset pin was high before this code runs that
it will very briefly be driven low because of passing GPIOD_OUT_LOW when
requesting the GPIO only to be driven high again possibly directly after
that. Such a very brief driving low of the reset pin may put the chip in
a confused state.
Request the GPIO in high (reset the chip) state instead to avoid this,
turning the initial gpiod_set_value() in mt9m114_power_on() into a no-op.
and the fsleep() ensures that it will stay high long enough to properly
reset the chip.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7345d6d356 ]
Once an async connection is found to be matching with an fwnode, a
sub-device may be registered (in case it wasn't already), its bound
operation is called, ancillary links are created, the async connection
is added to the sub-device's list of connections and removed from the
global waiting connection list. Further on, the sub-device's possible own
notifier is searched for possible additional matches.
Fix these specific issues:
- If v4l2_async_match_notify() failed before the sub-notifier handling,
the async connection was unbound and its entry removed from the
sub-device's async connection list. The latter part was also done in
v4l2_async_match_notify().
- The async connection's sd field was only set after creating ancillary
links in v4l2_async_match_notify(). It was however dereferenced in
v4l2_async_unbind_subdev_one(), which was called on error path of
v4l2_async_match_notify() failure.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: "Yew, Chang Ching" <chang.ching.yew@intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68cd8ac994 ]
Add release_mem_region() if ioremap() fails to release the memory
region obtained by cx25821_get_resources().
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fdf6323c3 ]
Clang with CONFIG_UBSAN_SHIFT=y noticed a condition where a signed type
(literal "1" is an "int") could end up being shifted beyond 32 bits,
so instrumentation was added (and due to the double is_tw286x() call
seen via inlining), Clang decides the second one must now be undefined
behavior and elides the rest of the function[1]. This is a known problem
with Clang (that is still being worked on), but we can avoid the entire
problem by actually checking the existing max chip ID, and now there is
no runtime instrumentation added at all since everything is known to be
within bounds.
Additionally use an unsigned value for the shift to remove the
instrumentation even without the explicit bounds checking.
Link: https://github.com/ClangBuiltLinux/linux/issues/2144 [1]
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
[hverkuil: fix checkpatch warning for is_tw286x]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8333c8262 ]
When pvr2_send_request_ex() submits a write URB successfully but fails to
submit the read URB (e.g. returns -ENOMEM), it returns immediately without
waiting for the write URB to complete. Since the driver reuses the same
URB structure, a subsequent call to pvr2_send_request_ex() attempts to
submit the still-active write URB, triggering a 'URB submitted while
active' warning in usb_submit_urb().
Fix this by ensuring the write URB is unlinked and waited upon if the read
URB submission fails.
Reported-by: syzbot+405dcd13121ff75a9e16@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=405dcd13121ff75a9e16
Signed-off-by: Szymon Wilczek <szymonwilczek@gmx.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90289b67c5 ]
The ADV7280-M may internally convert interlaced video input to
progressive video. If this mode is enabled, the ADV7280-M delivers
progressive video frames at the field rate of 50 fields per second (PAL)
or 60 fields per second (NTSC).
Fix the reported frame interval if progressive video is enabled.
Signed-off-by: Thorsten Schmelzer <tschmelzer@topcon.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95eed73b87 ]
In jdi_panel_dsi_remove(), jdi is explicitly checked, indicating that it
may be NULL:
if (!jdi)
mipi_dsi_detach(dsi);
However, when jdi is NULL, the function does not return and continues by
calling jdi_panel_disable():
err = jdi_panel_disable(&jdi->base);
Inside jdi_panel_disable(), jdi is dereferenced unconditionally, which can
lead to a NULL-pointer dereference:
struct jdi_panel *jdi = to_panel_jdi(panel);
backlight_disable(jdi->backlight);
To prevent such a potential NULL-pointer dereference, return early from
jdi_panel_dsi_remove() when jdi is NULL.
Signed-off-by: Tuo Li <islituo@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251218120955.11185-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d85f3207d7 ]
The V4L2_DEC_CMD_START command may be used to handle the dynamic source
change, which will triggers an implicit decoder drain.
The last_buffer_dequeued flag is set in the implicit decoder drain,
so driver need to clear it to continue the following decoding flow.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8618271887 ]
In this helper, any operation with a single DTR cycle (like 1S-1S-8D) is
considered requiring a duplicated command opcode. This is wrong as this
constraint only applies to octal DTR operations (8D-8D-8D).
Narrow the application of this constraint to the concerned bus
interface.
Note: none of the possible XD-XD-XD pattern, with X being one of {1, 2,
4} would benefit from this check either as there is only in octal DTR
mode that a single clock edge would be enough to transmit the full
opcode.
Make sure the constraint of expecting two bytes for the command is
applied to the relevant bus interface.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260109-winbond-v6-17-rc1-oddr-v2-3-1fff6a2ddb80@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e590752119 ]
This usually means that a TRS plug with no microphone pin has been plugged
into a TRRS socket. Cases where a user is plugging in a microphone while
pressing a button will be handled via incoming interrupt after the user
releases the button, so the microphone will still be detected once it
becomes usable.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260105-wm8962-l5-fixes-v1-3-f4f4eeacf089@puri.sm
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66c26346ae ]
This bit is handled by a separate control.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260105-wm8962-l5-fixes-v1-1-f4f4eeacf089@puri.sm
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd1ef5e245 ]
If the firmware is not running during TDR (e.g., when the driver is
unloading), there's no need to toggle scheduling in the GuC. In such
cases, skip this step.
v4:
- Bail on wait UC not running (Niranjana)
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Link: https://patch.msgid.link/20260110012739.2888434-4-matthew.brost@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0839d8d24e ]
This avoids any issues with dpia endpoints
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39c21b8111 ]
VFs use the PF SDMA ucode and are unable to load SDMA_RS64.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Signed-off-by: Victor Skvortsov <Victor.Skvortsov@amd.com>
Reviewed-by: Gavin Wan <gavin.wan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7273acfd0a ]
The SoNiX KN85 keyboard identifies as the "Apple, Inc. Aluminium
Keyboard" and is not recognized as a non-apple keyboard. Adding "SoNiX
KN85 Keyboard" to the list of non-apple keyboards fixes the function
keys.
Signed-off-by: Joey Bednar <linux@joeybednar.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c979d8db7b ]
Trying to access link enc on a dpia link will cause a crash otherwise
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8cf9ddc54 ]
Only set an error on the fence if the fence is not
signalled. We can end up with a warning if the
per queue reset path signals the fence and sets an error
as part of the reset, but fails to recover.
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878a4b73c1 ]
[why]
Need to add function hook check before use
Reviewed-by: Mohit Bawa <mohit.bawa@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2fd14f579 ]
This initializes HDP IP version 6.1.1.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e92d7e493 ]
This is not supported by the hardware and trying to decode
these leads to LAT timeout errors.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da0380de4 ]
CMD_STOP being sent to encoder before last job is executed by device_run
can lead to an occasional dropped frame. Ensure that remaining ready
buffers are drained by making a call to v4l2_m2m_try_schedule.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4e26c6fc1 ]
When STREAMON(CAP) is called after STREAMON(OUT), the driver was failing to
switch states from VPU_INST_STATE_OPEN to VPU_INST_STATE_INIT_SEQ and
VPU_INST_STATE_PIC_RUN because the capture queue streaming boolean had not
yet been set to true. This led to a hang in the encoder since the state
was stuck in VPU_INST_STATE_OPEN. During the second call to
start_streaming, the sequence initialization and frame buffer allocation
should occur.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7575b8dfa9 ]
Initialize the v4l2_format to a default. Empty formats are
not allowed in V4L2, so this fixes v4l2-compliance issues:
fail: v4l2-test-formats.cpp(514): !pix.width || !pix.height
test VIDIOC_G_FMT: FAIL
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17e1e1641f ]
If prev->input != PREVIEW_INPUT_MEMORY the width and height weren't
clamped. Just always clamp.
This fixes a v4l2-compliance error:
fail: v4l2-test-subdevs.cpp(171): fse.max_width == ~0U || fse.max_height == ~0U
fail: v4l2-test-subdevs.cpp(270): ret && ret != ENOTTY
test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: FAIL
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44c03802a5 ]
The isp_video_mbus_to_pix/pix_to_mbus functions did not take
the last empty entry { 0, } of the formats array into account.
As a result, isp_video_mbus_to_pix would accept code 0 and
isp_video_pix_to_mbus would select code 0 if no match was found.
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac3be217c ]
When SPI communication is suspended by hardware automatically, it could
happen that few bits of next frame are already clocked out due to
internal synchronization delay.
To achieve a safe suspension, we need to ensure that each word must be
at least 8 SPI clock cycles long. That's why, if bpw is less than 8
bits, we need to use midi to reach 8 SPI clock cycles at least.
This will ensure that each word achieve safe suspension and prevent
overrun condition.
Signed-off-by: Deepak Kumar <deepak.kumar01@st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patch.msgid.link/20251218-stm32-spi-enhancements-v2-2-3b69901ca9fe@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4e620eccb ]
Currently the buffers are being filled until full, which works fine
for the transport stream, but not when reading sections, those have
to be returned to userspace immediately, otherwise dvbv5-scan will
just wait forever.
Add a 'flush' argument to dvb_vb2_fill_buffer to indicate whether
the buffer must be flushed or wait until it is full.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d96cb0b86d ]
There are message types when we would need to send a payload along with
the LARGE_CONFIG_GET message to provide information to the firmware on
what data is requested.
Such cases are the ALSA Kcontrol related messages when the high level
param_id tells only the type of the control, but the ID/index of the exact
control is specified in the payload area.
The caller must place the payload for TX before calling the set_get_data()
and this payload will be sent alongside with the message to the firmware.
The data area will be overwritten by the received data from firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea573a8e1 ]
[Why]
USB-C DisplayPort Alt Mode with concurrent USB data needs lane count
limitation to prevent incorrect 4-lane DP configuration when only 2 lanes
are available due to hardware lane sharing between DP and USB3.
[How]
Query DMUB for Alt Mode status (is_dp_alt_disable, is_usb, is_dp4) in
dcn32_link_encoder_get_max_link_cap() and cap DP to 2 lanes when USB is
active on USB-C port. Added inline documentation explaining the USB-C
lane sharing constraint.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Signed-off-by: LinCheng Ku <lincheng.ku@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb2bbe3838 ]
mas->cur_bits_per_word may not reflect the value of xfer->bits_per_word
when can_dma() is called. Use the right value instead.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-3-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 739062a9f1 ]
setup_fifo_params assumes these will be zero, it won't write these
registers if the initial mode is zero.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-4-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b57c3c3f2 ]
Only check and drain IH1 ring if CAM is not enabled.
If GPU is under reset, don't access IH to drain retry fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
