[ Upstream commit bc2e4bc952 ]
__mcb_register_driver() makes some sanity checks over mcb_driver
to check if .probe and .remove callbacks are set. However, since commit
3bd13ae04c ("gpio: menz127: simplify error path and remove remove()")
removed the .remove callback from menz127-gpio.c, not all mcb device
drivers implement .remove callback.
Remove .remove check to ensure all mcb device drivers can be loaded.
Signed-off-by: Jose Javier Rodriguez Barbarin <dev-josejavier.rodriguez@duagon.com>
Fixes: 3bd13ae04c ("gpio: menz127: simplify error path and remove remove()")
[ jth: added statement about menz127-gpio.c ]
Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Link: https://patch.msgid.link/16fb55bd59d9c1d2ce2443f41d4dec2048f9a8ec.1768562302.git.jth@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4796eaafd6 ]
MFD_AIROHA_AN8855 is referenced here but never defined, so drop it
from the Kconfig file.
Fixes: e2258cfd9b ("nvmem: an8855: Add support for Airoha AN8855 Switch EFUSE")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
Link: https://patch.msgid.link/20260116170846.733558-4-srini@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1195ca3b4 ]
bdc_run() can be ran during atomic context leading to a sleep during
atomic warning. Fix this by replacing read_poll_timeout() with
read_poll_timeout_atomic().
Fixes: 75ae051efc ("usb: gadget: bdc: use readl_poll_timeout() to simplify code")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20260120200754.2488765-1-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b010880b99 ]
Regulator requesting may result in deferred probing error which will
abort driver probing. To avoid this just use dev_err_probe which handles
deferred probing.
Fixes: 3904b28efb ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4feb753ba6 ]
The wm5102_clear_write_sequencer() helper may return an error
and just return, bypassing the cleanup sequence and causing
regulators to remain enabled, leading to a resource leak.
Change the direct return to jump to the err_reset label to
properly free the resources.
Fixes: 1c1c6bba57 ("mfd: wm5102: Ensure we always boot the device fully")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20251214145804.2037-1-vulab@iscas.ac.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff112f1ecd ]
This reverts commit aced969e9b.
It was determined that this was not the correct "fix", so should be
reverted.
Fixes: aced969e9b ("mmc: rtsx_pci_sdmmc: increase power-on settling delay to 5ms")
Cc: Matthew Schwartz <matthew.schwartz@linux.dev>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6e43e82c7 ]
When trying to run perf and sysfs mode simultaneously, the WARN_ON()
in tmc_etr_enable_hw() is triggered sometimes:
WARNING: CPU: 42 PID: 3911571 at drivers/hwtracing/coresight/coresight-tmc-etr.c:1060 tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc]
[..snip..]
Call trace:
tmc_etr_enable_hw+0xc0/0xd8 [coresight_tmc] (P)
tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc] (L)
tmc_enable_etr_sink+0x11c/0x250 [coresight_tmc]
coresight_enable_path+0x1c8/0x218 [coresight]
coresight_enable_sysfs+0xa4/0x228 [coresight]
enable_source_store+0x58/0xa8 [coresight]
dev_attr_store+0x20/0x40
sysfs_kf_write+0x4c/0x68
kernfs_fop_write_iter+0x120/0x1b8
vfs_write+0x2c8/0x388
ksys_write+0x74/0x108
__arm64_sys_write+0x24/0x38
el0_svc_common.constprop.0+0x64/0x148
do_el0_svc+0x24/0x38
el0_svc+0x3c/0x130
el0t_64_sync_handler+0xc8/0xd0
el0t_64_sync+0x1ac/0x1b0
---[ end trace 0000000000000000 ]---
Since the enablement of sysfs mode is separeted into two critical regions,
one for sysfs buffer allocation and another for hardware enablement, it's
possible to race with the perf mode. Fix this by double check whether
the perf mode's been used before enabling the hardware in sysfs mode.
mode:
[sysfs mode] [perf mode]
tmc_etr_get_sysfs_buffer()
spin_lock(&drvdata->spinlock)
[sysfs buffer allocation]
spin_unlock(&drvdata->spinlock)
spin_lock(&drvdata->spinlock)
tmc_etr_enable_hw()
drvdata->etr_buf = etr_perf->etr_buf
spin_unlock(&drvdata->spinlock)
spin_lock(&drvdata->spinlock)
tmc_etr_enable_hw()
WARN_ON(drvdata->etr_buf) // WARN sicne etr_buf initialized at
the perf side
spin_unlock(&drvdata->spinlock)
With this fix, we retain the check for CS_MODE_PERF in get_etr_sysfs_buf.
This ensures we verify whether the perf mode's already running before we
actually allocate the buffer. Then we can save the time of
allocating/freeing the sysfs buffer if race with the perf mode.
Fixes: 296b01fd10 ("coresight: Refactor out buffer allocation function for ETR")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Junhao He <hejunhao3@h-partners.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260121101543.2017014-3-wangyushan12@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dd5d4c036 ]
During the probe the refclk_pad pointer is set to NULL if the
'fsl,refclk-pad-mode' property is not defined in the devicetree node. But
in imx_hsio_configure_clk_pad() this pointer is unconditionally used which
could result in a NULL pointer dereference. So check the pointer before to
use it.
Fixes: 82c56b6dd2 ("phy: freescale: imx8qm-hsio: Add i.MX8QM HSIO PHY driver support")
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://patch.msgid.link/20260114-phy-fsl-imx8qm-hsio-fix-null-pointer-dereference-v1-1-730e941be464@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1feb0377b9 ]
When changes [1] and [2] have been applied to the driver etm4x, the
same modifications have been also collapsed in [3] and applied in
one shot to the driver etm3x.
While doing this, the driver etm3x has not been aligned to etm4x on
the use of non cpuslocked version of cpuhp callback setup APIs.
The current code triggers two run-time warnings when the kernel is
compiled with CONFIG_PROVE_LOCKING=y.
Use non cpuslocked version of cpuhp callback setup APIs in driver
etm3x, aligning it to the driver etm4x.
[1] commit 2d1a8bfb61 ("coresight: etm4x: Fix etm4_count race by
moving cpuhp callbacks to init")
[2] commit 22a550a306 ("coresight: etm4x: Allow etm4x to be built
as a module")
[3] commit 97fe626ce6 ("coresight: etm3x: Allow etm3x to be built
as a module")
Fixes: 97fe626ce6 ("coresight: etm3x: Allow etm3x to be built as a module")
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260108152427.357379-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f2d8d79cc ]
The PM reference count is not expected to be incremented on return in
functions starfive_wdt_probe.
However, pm_runtime_get_sync will increment pm usage counter
even failed. Forgetting to putting operation will result in a
reference leak here.
Replace it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: db728ea9c7 ("drivers: watchdog: Add StarFive Watchdog driver")
Signed-off-by: Kery Qi <qikeyu2017@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d63403d4e3 ]
A sign change is needed for proper calculation of the pressure.
This is a minor fix since it only affects users that might have custom
silicon from Honeywell that has honeywell,pmin-pascal != 0.
Also due to the fact that raw pressure values can not be lower
than output_min (400k-3.3M) there is no need to calculate a decimal for
the offset.
Fixes: 713337d914 ("iio: pressure: Honeywell mprls0025pa pressure sensor")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a228e0369 ]
Fix the scan_type sign and realbits assignment.
The pressure is a 24bit unsigned int between output_min and output_max.
transfer function A: 10% to 90% of 2^24
transfer function B: 2.5% to 22.5% of 2^24
transfer function C: 20% to 80% of 2^24
[MPR_FUNCTION_A] = { .output_min = 1677722, .output_max = 15099494 }
[MPR_FUNCTION_B] = { .output_min = 419430, .output_max = 3774874 }
[MPR_FUNCTION_C] = { .output_min = 3355443, .output_max = 13421773 }
Fixes: 713337d914 ("iio: pressure: Honeywell mprls0025pa pressure sensor")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fff3f1a7d8 ]
Interrupt falling/rising flags should only be defined in the device tree.
Fixes: 713337d914 ("iio: pressure: Honeywell mprls0025pa pressure sensor")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0ac56c92 ]
Make sure that the spi_transfer struct is zeroed out before use.
Fixes: a0858f0cd2 ("iio: pressure: mprls0025pa add SPI driver")
Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aced969e9b ]
The existing 1ms delay in sd_power_on is insufficient and causes resume
errors around 4% of the time.
Increasing the delay to 5ms resolves this issue after testing 300
s2idle cycles.
Fixes: 1f311c94aa ("mmc: rtsx: add 74 Clocks in power on flow")
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Link: https://patch.msgid.link/20260105060236.400366-3-matthew.schwartz@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b89921eed8 ]
In ni_usb_init(), if ni_usb_setup_init() fails, the function returns
-EFAULT without freeing the allocated writes buffer, leading to a
memory leak.
Additionally, ni_usb_setup_init() returns 0 on failure, which causes
ni_usb_init() to return -EFAULT, an inappropriate error code for this
situation.
Fix the leak by freeing writes in the error path. Modify
ni_usb_setup_init() to return -EINVAL on failure and propagate this
error code in ni_usb_init().
Fixes: 4e127de14f ("staging: gpib: Add National Instruments USB GPIB driver")
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Suggested-by: Dave Penkler <dpenkler@gmail.com>
Co-developed-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Jianhao Xu <jianhao.xu@seu.edu.cn>
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Link: https://patch.msgid.link/20251230034546.929452-1-zilin@seu.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484e622522 ]
If ni_usb_receive_bulk_msg() succeeds but without reading 16 bytes, then
the error code needs to be set. The current code returns success.
Fixes: 4e127de14f ("staging: gpib: Add National Instruments USB GPIB driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aSlMpbE4IrQuBGFS@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93bb95a112 ]
Having a prompt of "DMA support" suddenly appear during a
"make oldconfig" can be confusing. Add a little helpful text to
the prompt message.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260110232643.3533351-5-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79527d86ba ]
SERIAL_IMX_CONSOLE is a build option for the imx driver (SERIAL_IMX).
It does not build a separate console driver file, so it can't be built
as a module since it isn't built at all.
Change the Kconfig symbol from tristate to bool and update the help
text accordingly.
Fixes: 0db4f9b91c ("tty: serial: imx: enable imx serial console port as module")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://patch.msgid.link/20260110232643.3533351-2-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efcffd9a6a ]
gb_lights_light_config() stores channel_count before allocating the
channels array. If kcalloc() fails, gb_lights_release() iterates the
non-zero count and dereferences light->channels, which is NULL.
Allocate channels first and only then publish channels_count so the
cleanup path can't walk a NULL pointer.
Fixes: 2870b52bae ("greybus: lights: add lights implementation")
Link: https://lore.kernel.org/all/20260108103700.15384-1-chaitanyamishra.ai@gmail.com/
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Chaitanya Mishra <chaitanyamishra.ai@gmail.com>
Link: https://patch.msgid.link/20260108151254.81553-1-chaitanyamishra.ai@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5177144b5 ]
EXTCON_TCSS_CROS_EC isn't used anywhere else in the kernel tree,
so drop it from this Kconfig file.
(unless it should be EXTCON_USBC_CROS_EC ?)
Fixes: f1a2241778 ("usb: typec: ucsi: Implement ChromeOS UCSI driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://patch.msgid.link/20251228190604.2484082-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d63d868b31 ]
The code for this never went upstream. It was replaced by other code,
so this should be dropped.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216748
Fixes: cf996f0396 ("iio: test: test gain-time-scale helpers")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc3a6a942e ]
The ace2x driver can optionally use the HDA infrastructure, but can still
build without that. However, with SND_HDA_CORE=m and SND_HDA_ALIGNED_MMIO=y,
it fails to link as built-in:
aarch64-linux-ld: drivers/soundwire/intel_ace2x.o: in function `intel_shim_wake':
intel_ace2x.c:(.text+0x2518): undefined reference to `snd_hdac_aligned_read'
aarch64-linux-ld: intel_ace2x.c:(.text+0x25d4): undefined reference to `snd_hdac_aligned_read'
aarch64-linux-ld: intel_ace2x.c:(.text+0x268c): undefined reference to `snd_hdac_aligned_write'
Add a Kconfig dependency that forces the soundwire driver to be a loadable
module if necessary.
Fixes: 79e7123c07 ("soundwire: intel_ace2x: fix wakeup handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20251223215014.534756-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e849ada70c ]
filp_open() never returns NULL, it returns either a valid pointer or an
error pointer. Using IS_ERR_OR_NULL() is unnecessary. Additionally, if
filp were NULL, PTR_ERR(NULL) would return 0, leading to a misleading
error message.
Fixes: 74d8361be3 ("char: misc: add test cases")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202506132058.thWZHlrb-lkp@intel.com/
Signed-off-by: Alper Ak <alperyasinak1@gmail.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com>
Link: https://patch.msgid.link/20251226230248.113073-1-alperyasinak1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2daf0c67a ]
Attempting to make use of a 1080p@120Hz display mode with 10 bpc RGB on
my Acer XV275K P3 monitor results in a blank image. A similar behavior
has been reported on Philips 279M1RV.
The faulty modeline is created by drm_gtf_mode_complex() based on the
following EDID entry from the Standard Timings block:
GTF: 1920x1080 119.999987 Hz 16:9 138.840 kHz 368.759000 MHz
It's worth noting the computed pixel clock ends up being slightly higher
at 368.881000 MHz. Nevertheless, this seems to work consistently fine
with 8 bpc RGB.
After switching to 10 bpc, the TMDS character rate expected for the mode
increases to 461.101250 MHz, as per drm_hdmi_compute_mode_clock().
Since there is no entry for this rate in the ropll_tmds_cfg table, the
necessary HDMI PLL configuration parameters are calculated dynamically
by rk_hdptx_phy_clk_pll_calc(). However, the resulting output rate is
not quite a perfect match, i.e. 461.100000 MHz. That proved to be the
actual root cause of the problem.
Add a new entry to the TMDS configuration table and provide the
necessary frequency division coefficients for the PHY PLL to generate
the expected 461.101250 MHz output.
Fixes: 9d0ec51d7c ("phy: rockchip: samsung-hdptx: Add high color depth management")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patch.msgid.link/20251221-phy-hdptx-pll-fix-v2-1-ae4abf7f75a1@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbcbafb99d ]
For HW scatter gather transfers we still need to look for the queue. The
HW is capable of queueing 3 concurrent transfers and if we try more than
that we'll get the submit queue full and should return. Otherwise, if we
go ahead and program the new transfer, we end up discarding it.
Fixes: e97dc74359 ("dmaengine: axi-dmac: Add support for scatter-gather transfers")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
base-commit: 3980351785
change-id: 20251104-axi-dmac-fixes-and-improvs-e3ad512a329c
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://patch.msgid.link/20251104-axi-dmac-fixes-and-improvs-v1-2-3e6fd9328f72@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bd257181f ]
If 'hw_cyclic' is false we should still be able to do cyclic transfers in
"software". That was not working for the case where 'desc->num_sgs' is 1
because 'chan->next_desc' is never set with the current desc which means
that the cyclic transfer only runs once and in the next SOT interrupt we
do nothing since vchan_next_desc() will return NULL.
Fix it by setting 'chan->next_desc' as soon as we get a new desc via
vchan_next_desc().
Fixes: 0e3b67b348 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
base-commit: 3980351785
change-id: 20251104-axi-dmac-fixes-and-improvs-e3ad512a329c
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://patch.msgid.link/20251104-axi-dmac-fixes-and-improvs-v1-1-3e6fd9328f72@analog.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58ab9d7b66 ]
The VFF_4G_SUPPORT register is named differently in datasheets,
and its name is "VFF_ADDR2"; was this named correctly from the
beginning it would've been clearer that there was a mistake in
the programming sequence.
This register is supposed to hold the high bits to support the
DMA addressing above 4G (so, more than 32 bits) and not a bit
to "enable" the support for VFF 4G.
Fix the name of this register, and also fix its usage by writing
the upper 32 bits of the dma_addr_t on it when the SoC supports
such feature.
Fixes: 9135408c3a ("dmaengine: mediatek: Add MediaTek UART APDMA support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251113122229.23998-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ffd02b822 ]
By using a regular non-overflow-checking add, the MediaTek icc-emi
driver will happy wrap at U32_MAX + 1 to 0. As it's common for the
interconnect core to fill in INT_MAX values, this is not a hypothetical
situation, but something that actually happens in regular use. This
would be pretty disasterous if anything used this driver.
Replace the addition with an overflow-checked addition from overflow.h,
and saturate to U32_MAX if an overflow is detected.
Fixes: b45293799f ("interconnect: mediatek: Add MediaTek MT8183/8195 EMI Interconnect driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20251124-mt8196-dvfsrc-v2-13-d9c1334db9f3@collabora.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 510f821444 ]
If the intention is that users of the interconnect declare their
relationship to the child icc_emi node of the dvfsrc controller, then
this code never worked. That's because it uses the parent dvfsrc device
as the device it passes to the interconnect core framework, which means
all the OF parsing is broken.
Use the actual device instead, and pass the dvfsrc parent into the
dvfsrc calls.
Fixes: b45293799f ("interconnect: mediatek: Add MediaTek MT8183/8195 EMI Interconnect driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20251124-mt8196-dvfsrc-v2-12-d9c1334db9f3@collabora.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 750e0e0a16 ]
After renaming round_rate->determine, kerneldoc does not match anymore,
causing W=1 warnings:
pll.c:102 function parameter 'req' not described in 'zynqmp_pll_determine_rate'
pll.c:102 expecting prototype for zynqmp_pll_round_rate(). Prototype was for zynqmp_pll_determine_rate() instead
Fixes: 193650c7a8 ("clk: zynqmp: pll: convert from round_rate() to determine_rate()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b87738649 ]
After renaming round_rate->determine, kerneldoc does not match anymore,
causing W=1 warnings:
Warning: drivers/clk/zynqmp/divider.c:122 function parameter 'req' not described in 'zynqmp_clk_divider_determine_rate'
Warning: drivers/clk/zynqmp/divider.c:122 expecting prototype for zynqmp_clk_divider_round_rate(). Prototype was for zynqmp_clk_divider_determine_rate() instead
Fixes: 0f9cf96a01 ("clk: zynqmp: divider: convert from round_rate() to determine_rate()")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa2ad19210 ]
devm_pm_runtime_enable() can fail due to memory allocation. The current
code ignores its return value, and when pm_runtime_resume_and_get() fails,
it returns directly without unmapping the shared_io region.
Add error handling for devm_pm_runtime_enable(). Reorder cleanup labels
to properly unmap shared_io on pm_runtime_resume_and_get() failure.
Fixes: 2f7b1d8b55 ("clk: mediatek: Do a runtime PM get on controllers during probe")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19024c9980 ]
All the MFGPLL require MFG_EB to be on for any operation on them, and
they only tick when MFG_EB is on as well, therefore making this a
parent-child relationship.
This dependency wasn't clear during the initial upstreaming of these
clock controllers, as it only made itself known when I could observe
the effects of the clock by bringing up a different piece of hardware.
Add a new PLL_PARENT_EN flag to mediatek's clk-pll.h, and check for it
when initialising the pll to then translate it into the actual
CLK_OPS_PARENT_ENABLE flag.
Then add the mfg_eb parent to the mfgpll clocks, and set the new
PLL_PARENT_EN flag.
Fixes: 03dc02f8c7 ("clk: mediatek: Add MT8196 mfg clock support")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 871afb43e4 ]
Since commit 8ceff24a75 ("clk: mediatek: clk-gate: Refactor
mtk_clk_register_gate to use mtk_gate struct") the mtk_gate structs
are no longer just used for initialization/registration, but also at
runtime. So drop __initconst annotations.
Fixes: 8ceff24a75 ("clk: mediatek: clk-gate: Refactor mtk_clk_register_gate to use mtk_gate struct")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laura Nao <laura.nao@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30a807808c ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 0f9cf96a01 ("clk: zynqmp: divider: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb1b0e63db ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: f7a6bed91a ("clk: x86: cgu: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c1cfb488 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 9e3372b2eb ("clk: versaclock3: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2532795a6d ]
The divider_round_rate_parent() function is now deprecated, so let's
migrate to divider_determine_rate() instead so that this deprecated API
can be removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: cd1cb38836 ("clk: stm32: stm32-core: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6587c9dacc ]
The divider_ro_round_rate() function is now deprecated, so let's migrate
to divider_ro_determine_rate() instead so that this deprecated API can
be removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: cd1cb38836 ("clk: stm32: stm32-core: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f78fb94229 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: deb4740a5f ("clk: sprd: div: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77b04dc196 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Note that this commit also removes a debugging message that's not really
needed.
Fixes: 9a3b699361 ("clk: sophgo: sg2042-clkgen: convert from round_rate() to determine_rate()")
Tested-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af943663cc ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 0879768df2 ("clk: nxp: lpc32xx: convert from round_rate() to determine_rate()")
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9329d784ca ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 215f8aa095 ("clk: nuvoton: ma35d1-divider: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 865e63b038 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 7b45988fcf ("clk: milbeaut: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d3c676e7 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: bb40a2ef4f ("clk: loongson1: convert from round_rate() to determine_rate()")
Reviewed-by: Keguang Zhang <keguang.zhang@gmail.com>
Tested-by: Keguang Zhang <keguang.zhang@gmail.com> # on LS1B & LS1C
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3a5249c14 ]
The divider_round_rate() function is now deprecated, so let's migrate
to divider_determine_rate() instead so that this deprecated API can be
removed.
Note that when the main function itself was migrated to use
determine_rate, this was mistakenly converted to:
req->rate = divider_round_rate(...)
This is invalid in the case when an error occurs since it can set the
rate to a negative value.
Fixes: 619a6210f3 ("clk: hisilicon: clkdivider-hi6220: convert from round_rate() to determine_rate()")
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
