This node has no 'reg' property, so it shouldn't have a unit address
(after '@') either
Fixes: b0d5c96e86 ("arm64: dts: qcom: sdm845-oneplus: Add framebuffer")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20260402-beryllium-fb-v4-2-46170004da28@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add framebuffer for early console and u-boot support.
Signed-off-by: Petr Hodina <petr.hodina@protonmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260402-beryllium-fb-v4-1-46170004da28@ixit.cz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The Sony IMX355 is the front camera on the Pixel 3a, mounted in portrait
mode. It is connected to CSIPHY1 and CCI I2C1, and uses MCLK2. Add
support for it.
Co-developed-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Robert Mader <robert.mader@collabora.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260331194437.41041-4-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The camera subsystem is added for the SoC common devicetree, but the
mclk pins should also be common across the SoC. Add the mclk pins for
the cameras.
Suggested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/5135823c-f2e4-4873-9e3a-9d190cac0113@oss.qualcomm.com
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bod@kernel.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20260331194437.41041-3-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Endpoints cannot be pre-defined since commit dcf6fb89e6 ("media: qcom:
camss: remove a check for unavailable CAMSS endpoint") was applied,
probing all endpoint nodes and requiring them to have a remote. There is
no sensible remote in the SoC devicetree because camera sensors are
board-specific.
The ports are meant to be extended by a board devicetree in order to
define fully configured endpoints and connect the ports to camera
sensors. For nodes that are only meaningful if extended, labels are
usually assigned. Label these ports so they can be extended directly.
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20260331194437.41041-2-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Make the dt checker happy by filling out the required properties in
line with the schematics.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-10-576ec5c4e631@oss.qualcomm.com
[bjorn: Remove reference to dropped 12V supply]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-9-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-8-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-7-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-6-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-5-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-4-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-3-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Fix up the supply name to align with bindings.
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-2-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Merge a change that drops the incorrectly added vddrfa1p8-supply to the
WCN6855 Bluetooth binding, so that it can go together with the
DeviceTree changes and avoid introducing new errors/warnings.
Add a devicetree for the Nothing Phone (3a) smartphone, which is based
on the Milos/SM7635 SoC.
Supported functionality as of this initial submission:
* Camera flash/torch LED
* Debug UART
* Glyph LEDs (AW20036)
* PMIC-GLINK (Charger, Fuel gauge, USB-C mode switching)
* Assistant Key, Power Button, Volume Keys
* Regulators (PM7550, PM8550VS, PMR735B)
* Remoteprocs (ADSP, CDSP, MPSS, WPSS)
* USB (USB2 + FSA4480)
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://lore.kernel.org/r/20260323-asteroids-v2-3-1a35fa9e178a@pm.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The rmtfs_mem region is currently sized at 6MiB but the default for
milos downstream is 2.5MiB. This causes remoteproc crashes on devices
that expect the smaller size:
modem_ac.c:281:Access Control Error: Could not protect the region specified:Start:e1f00000 End:e2180000, PID:1
Reduce the default to 2.5MiB to match the QCOM downstream config, and
override the size for FP6.
Fixes: d9d59d105f ("arm64: dts: qcom: Add initial Milos dtsi")
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://lore.kernel.org/r/20260323-asteroids-v2-1-1a35fa9e178a@pm.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
According to internal documentation, the corners specific for each rate
from the DP link clock are:
- LOWSVS_D1 -> 19.2 MHz
- LOWSVS -> 270 MHz
- SVS -> 540 MHz (594 MHz in case of DP3)
- SVS_L1 -> 594 MHz
- NOM -> 810 MHz
- NOM_L1 -> 810 MHz
- TURBO -> 810 MHz
So fix all tables for each of the four controllers according to the
documentation, but since DP0 through DP2 have the same entries in their
tables, lets drop the DP1 and DP2 and have all of them share the DP0
table instead. However keep a separate table for the DP3 as it is
different for the SVS, compared to the rest of the controllers.
The 19.2 MHz @ LOWSVS_D1 isn't needed as it's not an actual working
frequency and the controller will never select it. So remove it.
Cc: stable@vger.kernel.org # v6.9+
Fixes: 1940c25eaa ("arm64: dts: qcom: x1e80100: Add display nodes")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260323-hamoa-fix-dp3-opp-table-v3-1-a823776bd1b0@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the MDSS nodes and add supplies and bindings for the Samsung S6E8FCO
DSI controller for the M1906F9 panel.
The ldo and iovcc gpio pins boot up with a current of 16 mA, but they work
fine with 2mA, so I used that.
mdss_dsi0_phy is powered by VDD_MX, see power-domains in sm6125.dtsi
Co-developed-by: Kamil Gołda <kamil.golda@protonmail.com>
Signed-off-by: Kamil Gołda <kamil.golda@protonmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Yedaya Katsman <yedaya.ka@gmail.com>
Link: https://lore.kernel.org/r/20260314-panel-patches-v4-3-1ecbb2c0c3c8@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Unfortunately, an erratum with engineering sample that I was not aware
of was exposed by adding pinctrl configuration to the icicle kit.
When routed to MSS IOs, i2c signals are never anything other than tied
low. Being an FPGA, a Libero workaround for this problem was created,
that involves routing i2c signals to the FPGA fabric when the MSS IO
option is selected in the configurator and then back to the intended pin
using the debug "fabric test" capability. This is invisible to user
facing information in the tooling and not mentioned in reference designs
documentation. It manifests solely in the .xml output from the MSS
configuration that the HSS firmware uses to configure the device, which
Linux now overwrites using the pinctrl information. As a result, I never
noticed this.
My original submission had the engineering sample configuration, but I
modified it on application after I was told it didn't work, not
realising that the report came from a colleague with a production
device, where the erratum was fixed and the workaround not automatically
implemented by Libero when creating a design.
Move this part of the pinctrl configuration out of the shared portion of
the icicle device trees, into the portions that are specific to
engineering sample and production devices so that the different settings
for i2c pins can be dealt with.
Although the reference design only has this workaround in place for
i2c1, as i2c0 is genuinely fabric routed, move it too since the
erratum affects both controllers.
Link: https://ww1.microchip.com/downloads/aemDocuments/documents/FPGA/ProductDocuments/Errata/polarfiresoc/microsemi_polarfire_soc_fpga_egineering_samples_errata_er0219_v1.pdf [3.3]
Fixes: 123f4276b5 ("riscv: dts: microchip: add pinctrl nodes for mpfs/icicle kit")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The starfive-camss driver and bindings were dropped, as they were no
longer being worked upon for destaging.
Drop the relevant node as well to avoid the following build warning:
"failed to match any schema with compatible: ['starfive,jh7110-camss']"
Reported-by: Conor Dooley <conor@kernel.org>
Closes: https://lore.kernel.org/all/20260420-very-cartel-645595ffd1c7@spud/
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Reviewed-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Extend the !assembly #ifdef guarding x86's custom WARN helpers to cover the
WARN macros themselves, as they aren't assembly friendly. This helps make
it clear that things like __WARN_validate_printf() don't need a dummy
definition for assembly code.
No functional change intended.
Suggested-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://patch.msgid.link/20260423145419.459988-3-seanjc@google.com
Add explicit printf() validation for x86-64's newfangled WARN
implementation, as most (all?) compilers fail to detect basic formatting
issues without the annotation. E.g. even goofs like printing a u64 as a
string aren't detected:
WARN_ONCE(1, "Bad message, %s", vcpu->arch.last_guest_tsc);
32-bit x86 doesn't support HAVE_ARCH_BUG_FORMAT_ARGS and uses generic
implementations that provide printf() validation. This means there's
now a big blind spot is code that is strictly x86-64. Inconveniently,
new features are also frequently x86-64-only.
Fix the blind 64-bit blind spot.
[ dhansen: changelog tweaks to flesh out the 64-bit-only details ]
Fixes: 5b472b6e5b ("x86_64/bug: Implement __WARN_printf()")
Fixes: 11bb4944f0 ("x86/bug: Implement WARN_ONCE()")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/adc1IrD8uqWdaOKv@yzhao56-desk.sh.intel.com
Link: https://patch.msgid.link/20260423145419.459988-2-seanjc@google.com
DOORBELL_BLOCK_n[0-63] is an array of GPU control register pages.
Each block is memory-mappable and contains a single DOORBELL register
used to trigger actions in the GPU.
Add definitions for the DOORBELL_BLOCK registers using the register! macro
so they can be used by future Tyr interfaces.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-6-8abfff8a0204@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Now that Tyr uses the register! macro, it no longer needs to define a
custom register struct or read/write functions, so delete them.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-5-8abfff8a0204@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Define the MMU_CONTROL register block with the kernel's register! macro
and replace the existing hand-written MMU register definitions with typed
register and field accessors.
This adds typed definitions for the MMU IRQ registers and the per-address
space MMU_AS_CONTROL registers, including TRANSTAB, MEMATTR, LOCKADDR,
COMMAND, FAULTSTATUS, STATUS, and TRANSCFG. It also introduces typed
enums for MMU commands, fault types, access types, address space modes,
memory attributes, and related MMU configuration fields.
For logical 64-bit MMU registers that are exposed as split 32-bit MMIO
registers, define both the typed 64-bit view and explicit low/high 32-bit
registers so the register layout remains documented without relying on
native 64-bit MMIO accesses.
This reduces open-coded bit manipulation, keeps MMU register layout
knowledge in one place, and makes the definitions easier to read and
maintain.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-4-8abfff8a0204@collabora.com
[aliceryhl: reformat long comment]
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Define the JOB_CONTROL register block with the kernel's register! macro
and replace the existing hand-written JOB IRQ register definitions with
typed register and field accessors.
This adds typed definitions for the raw status, clear, mask, and status
registers, including the per-CSG interrupt bits and the global interface
interrupt bit.
This reduces open-coded bit manipulation, keeps the JOB_CONTROL register
layout in one place, and makes the definitions easier to read and
maintain.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-3-8abfff8a0204@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Currently, Tyr prints just the upper 16 bits of the GPU_ID in the hex id
field, namely ARCH_MAJOR, ARCH_MINOR, ARCH_REV, and PRODUCT_MAJOR. The
VERSION_* fields are already printed separately as "major", "minor", and
"status".
Print the full 32-bit GPU_ID register instead of shifting it, so the hex
id reflects the complete register contents.
Before this change:
mali-g610 id 0xa867 major 0x0 minor 0x0 status 0x5
After this change:
mali-g610 GPU_ID 0xa8670005 major 0x0 minor 0x0 status 0x5
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-2-8abfff8a0204@collabora.com
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Define the GPU_CONTROL register block with the kernel's register! macro
and switch the current GPU control paths over to the new typed register
definitions.
This replaces manual register constants, bit masks, shifts, and the
hand-written GpuId parsing code with typed register and field accessors.
It also adds helpers for combining split 64-bit registers and uses the new
definitions in reset, L2 power-on, and GPU info readout/logging paths.
This reduces open-coded bit manipulation making the code easier to read
and maintain.
Acked-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Co-developed-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Signed-off-by: Deborah Brouwer <deborah.brouwer@collabora.com>
Link: https://patch.msgid.link/20260409-b4-tyr-use-register-macro-v5-v5-1-8abfff8a0204@collabora.com
[aliceryhl: reformat long comment]
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
This code is more simply expressed using Option::filter instead of the
and_then with conditional.
This fixes the following warning with latest nightly Rust clippy build:
warning: manual implementation of `Option::filter`
--> drivers/gpu/nova-core/firmware.rs:391:14
|
391 | .and_then(|hdr| {
| ______________^
392 | | if hdr.bin_magic == BIN_MAGIC {
393 | | Some(hdr)
394 | | } else {
... |
397 | | })
| |______________^ help: try: `filter(|hdr| hdr.bin_magic == BIN_MAGIC)`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#manual_filter
= note: `-D clippy::manual-filter` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(clippy::manual_filter)]`
Cc: stable@vger.kernel.org
Fixes: d6cb7319e6 ("gpu: nova-core: firmware: add support for common firmware header")
Signed-off-by: Eliot Courtney <ecourtney@nvidia.com>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Link: https://patch.msgid.link/20260423-fix-filter-v1-1-b3b197c65daf@nvidia.com
[aliceryhl: add Fixes: tag and quote the warning it fixes]
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Commit 5f4f954bba ("dt-bindings: bluetooth: bring the HW description
closer to reality for wcn6855") changed the vddrfa1p7-supply to 1p8
for whatever reason.
The schematics footprint for this chip definitely says 7 on the input
leg and the driver still expects 1p7. Bring it back.
Fixes: 5f4f954bba ("dt-bindings: bluetooth: bring the HW description closer to reality for wcn6855")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260225-topic-wcn6855_pmu_dtbdings-v3-1-576ec5c4e631@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The N32 system call ABI expects 64-bit values directly in registers.
This does not work on nolibc currently, as a 'long' is only 32 bits
wide. Switch the system call wrappers to use 'long long' instead which
can handle 64-bit values on N32. As on N64 'long' and 'long long' are
the same, this does not change the behavior there.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260418-nolibc-largefile-v1-5-b91f0775bac3@weissschuh.net
The x32 system call ABI expects 64-bit values directly in registers.
This does not work on nolibc currently, as a 'long' is only 32 bits
wide. Switch the system call wrappers to use 'long long' instead which
can handle 64-bit values on x32. As on x86_64 'long' and 'long long' are
the same, this does not change the behavior there.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260418-nolibc-largefile-v1-4-b91f0775bac3@weissschuh.net
Currently all system call wrappers return 'long' integers which can be
directly cast to 'void *' if the returned value is actually a pointer.
An upcoming change will change the system call wrappers to sometimes
return 'long long' which can not be cast to a pointer directly.
Add explicit cast through 'long' to prepare for this.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260418-nolibc-largefile-v1-3-b91f0775bac3@weissschuh.net
In the architecture specific system call glue, all arguments are
currently casted to 'long' to fit into registers. This works for
pointers as 'long' has the same size as pointers.
However the system call registers for X32 and MIPS N32 need to be
'long long' to work correctly for 64-bit values expected by the system
call ABI. Casting a pointer to a 'long long' will produce a compiler
warning while casting 64-bit integers to 'long' will truncate those.
Add a helper which can be used to correctly cast both pointers and
integers into 'long long' registers. Cast the pointers through
'unsigned' to avoid any sign extensions.
Both builtins have been available since at least GCC 3 and clang 3.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260418-nolibc-largefile-v1-2-b91f0775bac3@weissschuh.net
Fix a small typo in the description of the memory_hugetlb_accounting
mount option.
Signed-off-by: Petr Vaněk <arkamar@atlas.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
On some architectures the llseek system call contains a leading
underscore. Treat it the same way as llseek and prefer it over the
plain lseek system call as is necessary for 64-bit offset handling.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260418-nolibc-largefile-v1-1-b91f0775bac3@weissschuh.net
There is already an 'if REMOTEPROC' condition wrapping this config option,
making the 'depends on REMOTEPROC' statement a duplicate dependency
(dead code).
I propose leaving the outer 'if REMOTEPROC...endif' and removing the
individual 'depends on REMOTEPROC' statement.
This dead code was found by kconfirm, a static analysis tool for Kconfig.
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20260417221337.286313-1-julianbraha@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
The WARN_ON call in bpf_trampoline_update could never hit, because we
direct the code path with (total == 0) to out label, which effectively
skips the WARN_ON call.
The WARN_ON made sense back then when it checked tr->selector, but now
with total being set just inside the function it's useless.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20260424153905.354922-2-jolsa@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The stack protector is configured in _start_c() so we shouldn't
use it before then.
Add __nolibc_no_stack_protector to _start_c() to avoid the compiler
generating stack protector code for _start_c() and thus using it
before its configured.
Signed-off-by: Daniel Palmer <daniel@thingy.jp>
Link: https://patch.msgid.link/20260425111315.3191461-3-daniel@thingy.jp
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Test case demonstrating a bug in cnum comparison logic fixed by
previous commit. A pruning point is reached with r6 in two states:
1. 32-bit range of [0x7FFFFFF0, U32_MAX] ∪ [0, 0x10]
2. 32-bit range of [0x100, 0x200]
At pruning point the buggy is_state_visited() logic would assume that
would assume range (2) to be a subset of (1) and fail to explore the
path performing division by zero.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20260425-cnum-range-within-v1-2-2fdca70cb09d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
states.c:range_within() must be updated to properly check if
cnum-based range in an old state is a superset of a range in the cur
state. Currently it makes the decision using min/max accessors:
reg_umin(old) <= reg_umin(cur) <= reg_umax(old)
This is wrong for cnums that cross both UT_MAX/0 and ST_MAX/ST_MIN
boundaries. Consider cnum32{base=0x7FFFFFF0, size=0x80000020},
which represents values [0x7FFFFFF0, ..., U32_MAX, 0, ..., 0x10].
Its projections are u32_min/max=0/U32_MAX, s32_min/max=S32_MIN/MAX.
A register with range [0x100, 0x200] (which lies entirely in the gap
of the wrapping range) would pass the min/max check despite having no
overlap with the actual cnum arc.
This commit replaces min/max comparison with cnum{32,64}_is_subset()
operation. The operation implementation is verified using cbmc model
checker in [1].
[1] https://github.com/eddyz87/cnum-verif/
Fixes: bbc6310855 ("bpf: replace min/max fields with struct cnum{32,64}")
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20260425-cnum-range-within-v1-1-2fdca70cb09d@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The recent addition of explicit constructor orders for fixture tests
broke the ordering of those relative to non-fixture tests and the
reverse-constructor-order detection.
Restore the ordering of the test functions relative to each other by
using the same explicit test order for all test registrations and
__constructor_order_first().
Rename the constant, as it is not specific to TEST_F() anymore.
Link: https://lore.kernel.org/r/20260422-kselftests-harness-order-v2-1-93ea980ea3ac@linutronix.de
Fixes: 6be2681514 ("selftests/harness: order TEST_F and XFAIL_ADD constructors")
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
