Use macros to describe gpios will make the dts easier to
read and write.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[converted interrupt-gpios and new rk3399-evb backlight]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We found that the suspend process was blocked when it run into
ehci/ohci module due to clk-480m of usb2-phy was disabled.
The root cause is that usb2-phy suspended earlier than ehci/ohci
(usb2-phy will be auto suspended if no devices plug-in). and the
clk-480m provided by it was disabled if no module used. However,
some suspend process related ehci/ohci are base on this clock,
so we should refer it into ehci/ohci driver to prevent this case.
The u2phy clock flow like this:
===
u2phy ________________
| | |-----> UTMI_CLK ---------> | EHCI |
OSC_24M ---|---> PHY_PLL----|----|
|________^_______| |-----> 480M_CLK ---|G|---> | USBPHY_480M_SRC| ----> USBPHY_480M for SoC
|
|
GRF
===
Signed-off-by: William wu <wulf@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We haven't enabled eDP support yet, but we might as well describe the
pin now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We're going to need to amend this table in board files.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the aclk_vcodec that selects between
aclk_vdpu and aclk_vepu based on a bit set in the general register files.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip socs often have some tiny number of muxes not controlled from
the core clock controller but through bits set in the general register
files. Add a clock-type that can control these as well, so that we
don't need to work around them being absent.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Zynq Ultrascale MP uses version 1.4 of the Cadence IP core
which fixes some silicon bugs that needed software workarounds
in Version 1.0 that was used on Zynq systems.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch removes these warnings reported by dtc 1.4:
Warning (unit_address_vs_reg): Node /amba_apu has a reg or ranges
property, but no unit name
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
While applying patch d443a0aa3a: "HID: hid-sensor-hub: clear memory to
avoid random data", there was some issues in applying correct version of
the patch. This resulted in the breakage of sensor functions as all
request like power-up will be reset by the memset() in the function
sensor_hub_set_feature().
The reset of caller buffer should be in the function
sensor_hub_get_feature(), not in the sensor_hub_set_feature().
Fixes: d443a0aa3a ("HID: hid-sensor-hub: clear memory to avoid random data")
Cc: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In future patches, we require greater flexibility in describing
the number of scalers available on each CRTC. To ease that transition
we move the current assignment to intel_device_info.
Scaler structure initialisation is done if scaler is available on the CRTC.
Gen9 check is not required as on depending upon numbers of scalers we
initialize scalers or return without doing anything in skl_init_scalers.
v3: Changed skl_init_scaler to intel_crtc_init_scalers
v2: Added Chris's comments.
Signed-off-by: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480398794-22741-1-git-send-email-nabendu.bikash.maiti@intel.com
The DolphinBar by Mayflash (identified as Dragonrise) needs
HID_QUIRK_MULTI_INPUT to split it up into four input devices. Without this
quirk the adapter is falsely recognized as a tablet. See also bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Signed-off-by: Marcel Hasler <mahasler@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Futaba TOSD-5711BB VFD crashes when the initial HID report is requested,
register the display in hid-ids and tell hid-quirks to not do the init.
Signed-off-by: Alex Wood <thetewood@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In ishtp_hid_probe(), use %04X instead of %04hX to format __u32 values,
in order to silent a format error reported by clang:
drivers/hid/intel-ish-hid/ishtp-hid.c:212:3: error: format specifies
type 'unsigned short' but the argument has type '__u32' (aka
'unsigned int') [-Werror,-Wformat]
hid->vendor, hid->product);
^~~~~~~~~~~
drivers/hid/intel-ish-hid/ishtp-hid.c:212:16: error: format
specifies type 'unsigned short' but the argument has type '__u32'
(aka 'unsigned int') [-Werror,-Wformat]
hid->vendor, hid->product);
^~~~~~~~~~~~
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Structure ishtp_device contains a logging function, print_log(), which
formats some of its parameters using vsnprintf(). Add a __printf
attribute to this function field (and to ish_event_tracer()) in order to
detect at compile time issues related to the printf-like formatting.
While at it, make format parameter a const pointer as print_log() is not
supposed to modify it.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At maximum CPU frequency of 300 MHz the maximum pixel clock frequency
is 37.5 MHz[1]. We must filter out any mode for which the calculated
pixel clock rate would exceed this value.
Specify the max-pixelclock property for the display node for
da850-lcdk.
[1] http://www.ti.com/lit/ds/symlink/am1808.pdf
(SPRS653E, revised March 2014, table 6-110)
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: commit message update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the vga-bridge node to the board DT together with corresponding
ports and vga connector. This allows to retrieve the edid info from
the display automatically.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It's just an example, but lets make it look more real to don't confuse
people about possible REG_RULE usage. Channels are 20 MHz wide, so start
and end frequencies are 10 MHz away from the center one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's maintained by Seth Forshe for a long time now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The tilcdc node name is 'display' as per the ePAPR 1.1 recommendation.
The label is also 'display', but change it to 'lcdc' to make it clear
what the underlying hardware is.
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The code was setting the capabilities byte to zero,
after it was already properly set previously. Fix it.
The bug was found while debugging hwsim mesh tests failures
that happened since the commit mentioned below.
Fixes: 76f43b4c0a ("mac80211: Remove invalid flag operations in mesh TSF synchronization")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Everytime the usb20 phy is enabled, there is a
"sleeping function called from invalid context" BUG.
In addition, there is a recursive locking happening
because of the recurse call to clk_enable().
clk_enable() from arch/arm/mach-davinci/clock.c uses
spin_lock_irqsave() before to invoke the callback
usb20_phy_clk_enable(). usb20_phy_clk_enable() uses
clk_get() and clk_enable_prepapre() which may sleep.
Replace clk_prepare_enable() by davinci_clk_enable().
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Suggested-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor commit description adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In some cases, there is a need to enable a clock as part of
clock enable callback of a different clock. For example, USB
2.0 PHY clock enable requires USB 2.0 clock to be enabled.
In this case, it is safe to instead call __clk_enable()
since the clock framework lock is already taken. Calling
clk_enable() causes recursive locking error.
A similar case arises in the clock disable path.
To enable such usage, make __clk_{enable,disable} functions
publicly available outside of clock.c. Also, call them
davinci_clk_{enable|disable} now to be consistent with how
other davinci-specific clock functions are named.
Note that these functions are not exported to drivers. They
are meant for usage in platform specific clock management
code.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Suggested-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a gpio-keys node for two user buttons present on the board.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I noticed my e-mail address is wrong in this one. This patch fixes it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since commit b36581df7e ("spi: imx: Using existing properties for
chipselects") the device tree property 'fsl,spi-num-chipselects' is
unused and it is already marked as obsolete in device tree binding
documentation. Remove the property from the existing DTS files to
avoid its reoccurence on copying.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This function is confusing - its second argument is an index to the
freq table, not the requested clock rate in Hz, but it's used as the
set_rate callback for the pll0 clock. It leads to an oops when the
caller doesn't know the internals and passes the rate in Hz as
argument instead of the cpufreq index since this argument isn't bounds
checked either.
Fix it by iterating over the array of supported frequencies and
selecting a one that matches or returning -EINVAL for unsupported
rates.
Also: update the davinci cpufreq driver. It's the only user of this
clock and currently it passes the cpufreq table index to
clk_set_rate(), which is confusing. Make it pass the requested clock
rate in Hz.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[nsekhar@ti.com: commit headline update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The function intel_atomic_get_shared_dpll_state() is only called from
intel_dpll_mgr.c and it concerns the same data structures as the other
functions in that file, so move it there and make it static.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1483024933-3726-8-git-send-email-ander.conselvan.de.oliveira@intel.com
With gcc 4.1.2:
drivers/usb/serial/f81534.c: In function ‘f81534_port_probe’:
drivers/usb/serial/f81534.c:1250: warning: comparison is always false due to limited range of data type
f81534_logic_to_phy_port() may return a negative error value, which is
ignored by assigning it to u8 f81534_port_private.phy_num.
Use an intermediate variable of type int to fix this.
While at it, forward the actual error code instead of converting it to
-ENODEV, and drop the useless check for F81534_NUM_PORT, as the callee
always returns a valid port number in case of success.
Fixes: 0c9bd6004d ("USB: serial: add Fintek F81532/534 driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Similarly to the aemif clock - this screws up the linked list of clock
children. Create a separate clock for mdio inheriting the rate from
emac_clk.
Cc: <stable@vger.kernel.org> # 3.12.x-
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a comment over mdio_clk to explaing its existence +
commit headline updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The aemif clock is added twice to the lookup table in da850.c. This
breaks the children list of pll0_sysclk3 as we're using the same list
links in struct clk. When calling clk_set_rate(), we get stuck in
propagate_rate().
Create a separate clock for nand, inheriting the rate of the aemif
clock and retrieve it in the davinci_nand module.
Cc: <stable@vger.kernel.org> # 4.9.x
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fix build errors on arch/um, which does not support HAS_IOMEM,
while the oxnas_nand.c driver uses interfaces that are
supplied by HAS_IOMEM.
(loadable module build:)
ERROR: "devm_ioremap_resource" [drivers/mtd/nand/oxnas_nand.ko] undefined!
or (built-in build:)
drivers/built-in.o: In function `oxnas_nand_probe':
drivers/mtd/nand/oxnas_nand.c:102: undefined reference to `devm_ioremap_resource'
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add
the new ID to the supported Devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_hsotg_ep_enable can be called from interrupt context, so all
allocations should be done with GFP_ATOMIC flags. This fixes following
issue on ARM architecture:
[<c010d830>] (unwind_backtrace) from [<c010a51c>] (show_stack+0x10/0x14)
[<c010a51c>] (show_stack) from [<c032930c>] (dump_stack+0x74/0x94)
[<c032930c>] (dump_stack) from [<c011cd30>] (__warn+0xd4/0x100)
[<c011cd30>] (__warn) from [<c011cd7c>] (warn_slowpath_null+0x20/0x28)
[<c011cd7c>] (warn_slowpath_null) from [<c0187e04>] (smp_call_function_many+0xcc/0x2a4)
[<c0187e04>] (smp_call_function_many) from [<c0188014>] (on_each_cpu_mask+0x38/0xa8)
[<c0188014>] (on_each_cpu_mask) from [<c01ddfe0>] (start_isolate_page_range+0x134/0x1b8)
[<c01ddfe0>] (start_isolate_page_range) from [<c01a3c14>] (alloc_contig_range+0xac/0x2f8)
[<c01a3c14>] (alloc_contig_range) from [<c01de3e4>] (cma_alloc+0xe0/0x1a8)
[<c01de3e4>] (cma_alloc) from [<c0110acc>] (__alloc_from_contiguous+0x38/0xe0)
[<c0110acc>] (__alloc_from_contiguous) from [<c0110ba4>] (cma_allocator_alloc+0x30/0x38)
[<c0110ba4>] (cma_allocator_alloc) from [<c0111034>] (__dma_alloc+0x1c0/0x2c8)
[<c0111034>] (__dma_alloc) from [<c01111b4>] (arm_dma_alloc+0x3c/0x48)
[<c01111b4>] (arm_dma_alloc) from [<c04ad800>] (dwc2_hsotg_ep_enable+0xec/0x46c)
[<c04ad800>] (dwc2_hsotg_ep_enable) from [<c04da610>] (usb_ep_enable+0x2c/0x3c)
[<c04da610>] (usb_ep_enable) from [<c04dc0c0>] (ecm_set_alt+0xa8/0x154)
[<c04dc0c0>] (ecm_set_alt) from [<c04d678c>] (composite_setup+0xd74/0x1540)
[<c04d678c>] (composite_setup) from [<c04ae048>] (dwc2_hsotg_complete_setup+0xb8/0x370)
[<c04ae048>] (dwc2_hsotg_complete_setup) from [<c04d987c>] (usb_gadget_giveback_request+0xc/0x10)
[<c04d987c>] (usb_gadget_giveback_request) from [<c04acafc>] (dwc2_hsotg_complete_request+0x78/0x128)
[<c04acafc>] (dwc2_hsotg_complete_request) from [<c04aed28>] (dwc2_hsotg_epint+0x69c/0x81c)
[<c04aed28>] (dwc2_hsotg_epint) from [<c04af6c4>] (dwc2_hsotg_irq+0xfc/0x748)
[<c04af6c4>] (dwc2_hsotg_irq) from [<c0163264>] (__handle_irq_event_percpu+0x58/0x140)
[<c0163264>] (__handle_irq_event_percpu) from [<c0163368>] (handle_irq_event_percpu+0x1c/0x58)
[<c0163368>] (handle_irq_event_percpu) from [<c01633dc>] (handle_irq_event+0x38/0x5c)
[<c01633dc>] (handle_irq_event) from [<c01666e4>] (handle_fasteoi_irq+0xc4/0x19c)
[<c01666e4>] (handle_fasteoi_irq) from [<c0162a2c>] (generic_handle_irq+0x18/0x28)
[<c0162a2c>] (generic_handle_irq) from [<c0162b40>] (__handle_domain_irq+0x6c/0xe4)
[<c0162b40>] (__handle_domain_irq) from [<c0101470>] (gic_handle_irq+0x50/0x9c)
[<c0101470>] (gic_handle_irq) from [<c010b00c>] (__irq_svc+0x6c/0xa8)
Fixes: 5f54c54b0b ("usb: dwc2: gadget: Add DDMA chain pointers to
dwc2_hsotg_ep structure")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.
Fixes: d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:
in probe:
...
err1:
pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
due to extcon
pm_runtime_disable(dev);
return ret;
in dwc3_omap_remove:
...
dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
of_platform_depopulate(omap->dev);
pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
pm_runtime_disable(&pdev->dev);
return 0;
So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dev_config() routine in gadgetfs has a check that
dev->dev->bNumConfigurations is equal to 1, and then contains a
redundant line of code setting the value to 1. This patch removes the
unnecessary assignment.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user. In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).
This patch adds the additional check and fixes the existing check. It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN use-after-free bug report in gadgetfs:
BUG: KASAN: use-after-free in gadgetfs_setup+0x208a/0x20e0 at addr ffff88003dfe5bf2
Read of size 2 by task syz-executor0/22994
CPU: 3 PID: 22994 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88006df06a18 ffffffff81f96aba ffffffffe0528500 1ffff1000dbe0cd6
ffffed000dbe0cce ffff88006df068f0 0000000041b58ab3 ffffffff8598b4c8
ffffffff81f96828 1ffff1000dbe0ccd ffff88006df06708 ffff88006df06748
Call Trace:
<IRQ> [ 201.343209] [< inline >] __dump_stack lib/dump_stack.c:15
<IRQ> [ 201.343209] [<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
[< inline >] print_address_description mm/kasan/report.c:197
[<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
[< inline >] kasan_report mm/kasan/report.c:306
[<ffffffff817e562a>] __asan_report_load_n_noabort+0x3a/0x40 mm/kasan/report.c:337
[< inline >] config_buf drivers/usb/gadget/legacy/inode.c:1298
[<ffffffff8322c8fa>] gadgetfs_setup+0x208a/0x20e0 drivers/usb/gadget/legacy/inode.c:1368
[<ffffffff830fdcd0>] dummy_timer+0x11f0/0x36d0 drivers/usb/gadget/udc/dummy_hcd.c:1858
[<ffffffff814807c1>] call_timer_fn+0x241/0x800 kernel/time/timer.c:1308
[< inline >] expire_timers kernel/time/timer.c:1348
[<ffffffff81482de6>] __run_timers+0xa06/0xec0 kernel/time/timer.c:1641
[<ffffffff814832c1>] run_timer_softirq+0x21/0x80 kernel/time/timer.c:1654
[<ffffffff84f4af8b>] __do_softirq+0x2fb/0xb63 kernel/softirq.c:284
The cause of the bug is subtle. The dev_config() routine gets called
twice by the fuzzer. The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set. But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.
The second time dev_config() is called, the user data contains only a
full-speed config descriptor. But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config. Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.
The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reports that fuzz testing with syzkaller causes a
KASAN warning in gadgetfs:
BUG: KASAN: slab-out-of-bounds in dev_config+0x86f/0x1190 at addr ffff88003c47e160
Write of size 65537 by task syz-executor0/6356
CPU: 3 PID: 6356 Comm: syz-executor0 Not tainted 4.9.0-rc7+ #19
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88003c107ad8 ffffffff81f96aba ffffffff3dc11ef0 1ffff10007820eee
ffffed0007820ee6 ffff88003dc11f00 0000000041b58ab3 ffffffff8598b4c8
ffffffff81f96828 ffffffff813fb4a0 ffff88003b6eadc0 ffff88003c107738
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96aba>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff817e4dec>] kasan_object_err+0x1c/0x70 mm/kasan/report.c:159
[< inline >] print_address_description mm/kasan/report.c:197
[<ffffffff817e5080>] kasan_report_error+0x1f0/0x4e0 mm/kasan/report.c:286
[<ffffffff817e5705>] kasan_report+0x35/0x40 mm/kasan/report.c:306
[< inline >] check_memory_region_inline mm/kasan/kasan.c:308
[<ffffffff817e3fb9>] check_memory_region+0x139/0x190 mm/kasan/kasan.c:315
[<ffffffff817e4044>] kasan_check_write+0x14/0x20 mm/kasan/kasan.c:326
[< inline >] copy_from_user arch/x86/include/asm/uaccess.h:689
[< inline >] ep0_write drivers/usb/gadget/legacy/inode.c:1135
[<ffffffff83228caf>] dev_config+0x86f/0x1190 drivers/usb/gadget/legacy/inode.c:1759
[<ffffffff817fdd55>] __vfs_write+0x5d5/0x760 fs/read_write.c:510
[<ffffffff817ff650>] vfs_write+0x170/0x4e0 fs/read_write.c:560
[< inline >] SYSC_write fs/read_write.c:607
[<ffffffff81803a5b>] SyS_write+0xfb/0x230 fs/read_write.c:599
[<ffffffff84f47ec1>] entry_SYSCALL_64_fastpath+0x1f/0xc2
Indeed, there is a comment saying that the value of len is restricted
to a 16-bit integer, but the code doesn't actually do this.
This patch fixes the warning. It replaces the comment with a
computation that forces the amount of data copied from the user in
ep0_write() to be no larger than the wLength size for the control
transfer, which is a 16-bit quantity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790
while dep->endpoint.desc is NULL.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Andrey Konovalov reported that we were not properly checking the upper
limit before of a device configuration size before calling
memdup_user(), which could cause some problems.
So set the upper limit to PAGE_SIZE * 4, which should be good enough for
all devices.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stop_activity() routine in dummy-hcd is supposed to unlink all
active requests for every endpoint, among other things. But it
doesn't handle ep0. As a result, fuzz testing can generate a WARNING
like the following:
WARNING: CPU: 0 PID: 4410 at drivers/usb/gadget/udc/dummy_hcd.c:672 dummy_free_request+0x153/0x170
Modules linked in:
CPU: 0 PID: 4410 Comm: syz-executor Not tainted 4.9.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffff88006a64ed10 ffffffff81f96b8a ffffffff41b58ab3 1ffff1000d4c9d35
ffffed000d4c9d2d ffff880065f8ac00 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 0000000041b58ab3 ffffffff859410e0 ffffffff813f0590
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff812b808f>] __warn+0x19f/0x1e0 kernel/panic.c:550
[<ffffffff812b831c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:585
[<ffffffff830fcb13>] dummy_free_request+0x153/0x170 drivers/usb/gadget/udc/dummy_hcd.c:672
[<ffffffff830ed1b0>] usb_ep_free_request+0xc0/0x420 drivers/usb/gadget/udc/core.c:195
[<ffffffff83225031>] gadgetfs_unbind+0x131/0x190 drivers/usb/gadget/legacy/inode.c:1612
[<ffffffff830ebd8f>] usb_gadget_remove_driver+0x10f/0x2b0 drivers/usb/gadget/udc/core.c:1228
[<ffffffff830ec084>] usb_gadget_unregister_driver+0x154/0x240 drivers/usb/gadget/udc/core.c:1357
This patch fixes the problem by iterating over all the endpoints in
the driver's ep array instead of iterating over the gadget's ep_list,
which explicitly leaves out ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reserved1 is documented as expected to be set to 0, but this test fails
when it it set to 0. Reverse the condition.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>