[ Upstream commit 84359d0a5e ]
mt9m114_probe() requests the reset GPIO in output low state:
sensor->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
and then almost immediately afterwards calls mt9m114_power_on() which does:
gpiod_set_value(sensor->reset, 1);
fsleep(duration);
gpiod_set_value(sensor->reset, 0);
which means that if the reset pin was high before this code runs that
it will very briefly be driven low because of passing GPIOD_OUT_LOW when
requesting the GPIO only to be driven high again possibly directly after
that. Such a very brief driving low of the reset pin may put the chip in
a confused state.
Request the GPIO in high (reset the chip) state instead to avoid this,
turning the initial gpiod_set_value() in mt9m114_power_on() into a no-op.
and the fsleep() ensures that it will stay high long enough to properly
reset the chip.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans de Goede <johannes.goede@oss.qualcomm.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7345d6d356 ]
Once an async connection is found to be matching with an fwnode, a
sub-device may be registered (in case it wasn't already), its bound
operation is called, ancillary links are created, the async connection
is added to the sub-device's list of connections and removed from the
global waiting connection list. Further on, the sub-device's possible own
notifier is searched for possible additional matches.
Fix these specific issues:
- If v4l2_async_match_notify() failed before the sub-notifier handling,
the async connection was unbound and its entry removed from the
sub-device's async connection list. The latter part was also done in
v4l2_async_match_notify().
- The async connection's sd field was only set after creating ancillary
links in v4l2_async_match_notify(). It was however dereferenced in
v4l2_async_unbind_subdev_one(), which was called on error path of
v4l2_async_match_notify() failure.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: "Yew, Chang Ching" <chang.ching.yew@intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68cd8ac994 ]
Add release_mem_region() if ioremap() fails to release the memory
region obtained by cx25821_get_resources().
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fdf6323c3 ]
Clang with CONFIG_UBSAN_SHIFT=y noticed a condition where a signed type
(literal "1" is an "int") could end up being shifted beyond 32 bits,
so instrumentation was added (and due to the double is_tw286x() call
seen via inlining), Clang decides the second one must now be undefined
behavior and elides the rest of the function[1]. This is a known problem
with Clang (that is still being worked on), but we can avoid the entire
problem by actually checking the existing max chip ID, and now there is
no runtime instrumentation added at all since everything is known to be
within bounds.
Additionally use an unsigned value for the shift to remove the
instrumentation even without the explicit bounds checking.
Link: https://github.com/ClangBuiltLinux/linux/issues/2144 [1]
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
[hverkuil: fix checkpatch warning for is_tw286x]
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8333c8262 ]
When pvr2_send_request_ex() submits a write URB successfully but fails to
submit the read URB (e.g. returns -ENOMEM), it returns immediately without
waiting for the write URB to complete. Since the driver reuses the same
URB structure, a subsequent call to pvr2_send_request_ex() attempts to
submit the still-active write URB, triggering a 'URB submitted while
active' warning in usb_submit_urb().
Fix this by ensuring the write URB is unlinked and waited upon if the read
URB submission fails.
Reported-by: syzbot+405dcd13121ff75a9e16@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=405dcd13121ff75a9e16
Signed-off-by: Szymon Wilczek <szymonwilczek@gmx.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90289b67c5 ]
The ADV7280-M may internally convert interlaced video input to
progressive video. If this mode is enabled, the ADV7280-M delivers
progressive video frames at the field rate of 50 fields per second (PAL)
or 60 fields per second (NTSC).
Fix the reported frame interval if progressive video is enabled.
Signed-off-by: Thorsten Schmelzer <tschmelzer@topcon.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95eed73b87 ]
In jdi_panel_dsi_remove(), jdi is explicitly checked, indicating that it
may be NULL:
if (!jdi)
mipi_dsi_detach(dsi);
However, when jdi is NULL, the function does not return and continues by
calling jdi_panel_disable():
err = jdi_panel_disable(&jdi->base);
Inside jdi_panel_disable(), jdi is dereferenced unconditionally, which can
lead to a NULL-pointer dereference:
struct jdi_panel *jdi = to_panel_jdi(panel);
backlight_disable(jdi->backlight);
To prevent such a potential NULL-pointer dereference, return early from
jdi_panel_dsi_remove() when jdi is NULL.
Signed-off-by: Tuo Li <islituo@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251218120955.11185-1-islituo@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d85f3207d7 ]
The V4L2_DEC_CMD_START command may be used to handle the dynamic source
change, which will triggers an implicit decoder drain.
The last_buffer_dequeued flag is set in the implicit decoder drain,
so driver need to clear it to continue the following decoding flow.
Signed-off-by: Ming Qian <ming.qian@oss.nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8618271887 ]
In this helper, any operation with a single DTR cycle (like 1S-1S-8D) is
considered requiring a duplicated command opcode. This is wrong as this
constraint only applies to octal DTR operations (8D-8D-8D).
Narrow the application of this constraint to the concerned bus
interface.
Note: none of the possible XD-XD-XD pattern, with X being one of {1, 2,
4} would benefit from this check either as there is only in octal DTR
mode that a single clock edge would be enough to transmit the full
opcode.
Make sure the constraint of expecting two bytes for the command is
applied to the relevant bus interface.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20260109-winbond-v6-17-rc1-oddr-v2-3-1fff6a2ddb80@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e590752119 ]
This usually means that a TRS plug with no microphone pin has been plugged
into a TRRS socket. Cases where a user is plugging in a microphone while
pressing a button will be handled via incoming interrupt after the user
releases the button, so the microphone will still be detected once it
becomes usable.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260105-wm8962-l5-fixes-v1-3-f4f4eeacf089@puri.sm
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66c26346ae ]
This bit is handled by a separate control.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20260105-wm8962-l5-fixes-v1-1-f4f4eeacf089@puri.sm
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd1ef5e245 ]
If the firmware is not running during TDR (e.g., when the driver is
unloading), there's no need to toggle scheduling in the GuC. In such
cases, skip this step.
v4:
- Bail on wait UC not running (Niranjana)
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Link: https://patch.msgid.link/20260110012739.2888434-4-matthew.brost@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0839d8d24e ]
This avoids any issues with dpia endpoints
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39c21b8111 ]
VFs use the PF SDMA ucode and are unable to load SDMA_RS64.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Signed-off-by: Victor Skvortsov <Victor.Skvortsov@amd.com>
Reviewed-by: Gavin Wan <gavin.wan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7273acfd0a ]
The SoNiX KN85 keyboard identifies as the "Apple, Inc. Aluminium
Keyboard" and is not recognized as a non-apple keyboard. Adding "SoNiX
KN85 Keyboard" to the list of non-apple keyboards fixes the function
keys.
Signed-off-by: Joey Bednar <linux@joeybednar.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c979d8db7b ]
Trying to access link enc on a dpia link will cause a crash otherwise
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8cf9ddc54 ]
Only set an error on the fence if the fence is not
signalled. We can end up with a warning if the
per queue reset path signals the fence and sets an error
as part of the reset, but fails to recover.
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878a4b73c1 ]
[why]
Need to add function hook check before use
Reviewed-by: Mohit Bawa <mohit.bawa@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2fd14f579 ]
This initializes HDP IP version 6.1.1.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e92d7e493 ]
This is not supported by the hardware and trying to decode
these leads to LAT timeout errors.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5da0380de4 ]
CMD_STOP being sent to encoder before last job is executed by device_run
can lead to an occasional dropped frame. Ensure that remaining ready
buffers are drained by making a call to v4l2_m2m_try_schedule.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4e26c6fc1 ]
When STREAMON(CAP) is called after STREAMON(OUT), the driver was failing to
switch states from VPU_INST_STATE_OPEN to VPU_INST_STATE_INIT_SEQ and
VPU_INST_STATE_PIC_RUN because the capture queue streaming boolean had not
yet been set to true. This led to a hang in the encoder since the state
was stuck in VPU_INST_STATE_OPEN. During the second call to
start_streaming, the sequence initialization and frame buffer allocation
should occur.
Signed-off-by: Brandon Brnich <b-brnich@ti.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7575b8dfa9 ]
Initialize the v4l2_format to a default. Empty formats are
not allowed in V4L2, so this fixes v4l2-compliance issues:
fail: v4l2-test-formats.cpp(514): !pix.width || !pix.height
test VIDIOC_G_FMT: FAIL
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17e1e1641f ]
If prev->input != PREVIEW_INPUT_MEMORY the width and height weren't
clamped. Just always clamp.
This fixes a v4l2-compliance error:
fail: v4l2-test-subdevs.cpp(171): fse.max_width == ~0U || fse.max_height == ~0U
fail: v4l2-test-subdevs.cpp(270): ret && ret != ENOTTY
test Try VIDIOC_SUBDEV_ENUM_MBUS_CODE/FRAME_SIZE/FRAME_INTERVAL: FAIL
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44c03802a5 ]
The isp_video_mbus_to_pix/pix_to_mbus functions did not take
the last empty entry { 0, } of the formats array into account.
As a result, isp_video_mbus_to_pix would accept code 0 and
isp_video_pix_to_mbus would select code 0 if no match was found.
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac3be217c ]
When SPI communication is suspended by hardware automatically, it could
happen that few bits of next frame are already clocked out due to
internal synchronization delay.
To achieve a safe suspension, we need to ensure that each word must be
at least 8 SPI clock cycles long. That's why, if bpw is less than 8
bits, we need to use midi to reach 8 SPI clock cycles at least.
This will ensure that each word achieve safe suspension and prevent
overrun condition.
Signed-off-by: Deepak Kumar <deepak.kumar01@st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patch.msgid.link/20251218-stm32-spi-enhancements-v2-2-3b69901ca9fe@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4e620eccb ]
Currently the buffers are being filled until full, which works fine
for the transport stream, but not when reading sections, those have
to be returned to userspace immediately, otherwise dvbv5-scan will
just wait forever.
Add a 'flush' argument to dvb_vb2_fill_buffer to indicate whether
the buffer must be flushed or wait until it is full.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d96cb0b86d ]
There are message types when we would need to send a payload along with
the LARGE_CONFIG_GET message to provide information to the firmware on
what data is requested.
Such cases are the ALSA Kcontrol related messages when the high level
param_id tells only the type of the control, but the ID/index of the exact
control is specified in the payload area.
The caller must place the payload for TX before calling the set_get_data()
and this payload will be sent alongside with the message to the firmware.
The data area will be overwritten by the received data from firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea573a8e1 ]
[Why]
USB-C DisplayPort Alt Mode with concurrent USB data needs lane count
limitation to prevent incorrect 4-lane DP configuration when only 2 lanes
are available due to hardware lane sharing between DP and USB3.
[How]
Query DMUB for Alt Mode status (is_dp_alt_disable, is_usb, is_dp4) in
dcn32_link_encoder_get_max_link_cap() and cap DP to 2 lanes when USB is
active on USB-C port. Added inline documentation explaining the USB-C
lane sharing constraint.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Signed-off-by: LinCheng Ku <lincheng.ku@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb2bbe3838 ]
mas->cur_bits_per_word may not reflect the value of xfer->bits_per_word
when can_dma() is called. Use the right value instead.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-3-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 739062a9f1 ]
setup_fifo_params assumes these will be zero, it won't write these
registers if the initial mode is zero.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-4-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b57c3c3f2 ]
Only check and drain IH1 ring if CAM is not enabled.
If GPU is under reset, don't access IH to drain retry fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9877a865d6 ]
If SDMA block not enabled, buffer_funcs will not initialize,
fix the null pointer issue if buffer_funcs not initialized.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2976aeb0de ]
Add an eDP panel entry for AUO B140HAN06.4 that is also used in
some variants of Lenovo Flex 5G with Qcom SC8180 SoC.
The raw edid of the panel is:
00 ff ff ff ff ff ff 00 06 af 3d 64 00 00 00 00
2b 1d 01 04 a5 1f 11 78 03 b8 1a a6 54 4a 9b 26
0e 52 55 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 14 37 80 b8 70 38 24 40 10 10
3e 00 35 ae 10 00 00 18 10 2c 80 b8 70 38 24 40
10 10 3e 00 35 ae 10 00 00 18 00 00 00 fe 00 41
55 4f 0a 20 20 20 20 20 20 20 20 20 00 00 00 fe
00 42 31 34 30 48 41 4e 30 36 2e 34 20 0a 00 eb
I do not have access to the datasheet and but it is tested on above
mentioned laptop for a few weeks and seems to work just fine with
timing info of similar panels.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20251203074555.690613-1-alexey.klimov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa93788dd ]
The USB2 port on Smaug is configured for OTG operation but lacked the
required 'usb-role-switch' property, leading to a failed probe and a
non-functioning USB port. Add the property along with setting the default
role to host.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c197179990 ]
This reverts commit 06d22ed6b6.
OP-TEE logic in U-Boot automatically injects a reserved-memory
node along with optee firmware node to kernel device tree.
The injection logic is dependent on that there is no manually
defined optee node. Having the node in zynqmp.dtsi effectively
breaks OP-TEE's insertion of the reserved-memory node, causing
memory access violations during runtime.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20251125-revert-zynqmp-optee-v1-1-d2ce4c0fcaf6@vaisala.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fda364cb7 ]
ffa_init() maps the Rx/Tx buffers via ffa_rxtx_map() but on the
partition setup failure path it never unmaps them.
Add the missing ffa_rxtx_unmap() call in the error path so that
the Rx/Tx buffers are properly released before freeing the backing
pages.
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Message-Id: <20251210031656.56194-1-lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05363abc76 ]
In persistent_ram_vmap(), vmap() may return NULL on failure.
If offset is non-zero, adding offset_in_page(start) causes the function
to return a non-NULL pointer even though the mapping failed.
persistent_ram_buffer_map() therefore incorrectly returns success.
Subsequent access to prz->buffer may dereference an invalid address
and cause crashes.
Add proper NULL checking for vmap() failures.
Signed-off-by: Ruipeng Qi <ruipengqi3@gmail.com>
Link: https://patch.msgid.link/20260203020358.3315299-1-ruipengqi3@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6080fb2116 ]
Updating "ppos" on error conditions does not make much sense. The pattern
is to return the error code directly without modifying the position, or
modify the position on success and return the number of bytes written.
Since on success, the return value of apply is 0, there is no point in
modifying ppos either. Fix it by removing all this and just returning
error code or number of bytes written on success.
Signed-off-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Acked-by: Tejun Heo <tj@kernel.org>
Tested-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20260126100050.3854740-3-arighi@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1affd29ffb ]
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
Remove IRQF_ONESHOT from irqflags.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-10-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03843d95a4 ]
request_threaded_irq() is invoked with a primary and a secondary handler
and no flags are passed. The primary handler is the same as
irq_default_primary_handler() so there is no need to have an identical
copy.
The lack of the IRQF_ONESHOT flag can be dangerous because the interrupt
source is not masked while the threaded handler is active. This means,
especially on LEVEL typed interrupt lines, the interrupt can fire again
before the threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary handler
is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-5-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebf35d8f93 ]
Before sending the data via the mailbox to the hardware, to ensure
that the data accessed by the hardware is the most up-to-date,
a write barrier should be added before writing to the mailbox register.
The current memory barrier is placed after writing to the register,
the barrier order should be modified to be before writing to the register.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8d4c6ecb ]
msix_capability_init() fails to unmap the MSI-X region if
msix_setup_interrupts() fails.
Add the missing iounmap() for that error path.
[ tglx: Massaged change log ]
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260125144452.2103812-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1278972b0 ]
The TMU device can be used as both a clocksource and a clockevent
provider. The driver tries to be smart and power itself on and off, as
well as enabling and disabling its clock when it's not in operation.
This behavior is slightly altered if the TMU is used as an early
platform device in which case the device is left powered on after probe,
but the clock is still enabled and disabled at runtime.
This has worked for a long time, but recent improvements in PREEMPT_RT
and PROVE_LOCKING have highlighted an issue. As the TMU registers itself
as a clockevent provider, clockevents_register_device(), it needs to use
raw spinlocks internally as this is the context of which the clockevent
framework interacts with the TMU driver. However in the context of
holding a raw spinlock the TMU driver can't really manage its power
state or clock with calls to pm_runtime_*() and clk_*() as these calls
end up in other platform drivers using regular spinlocks to control
power and clocks.
This mix of spinlock contexts trips a lockdep warning.
=============================
[ BUG: Invalid wait context ]
6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
ffff000008c9e180 (&dev->power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88
other info that might help us debug this:
context-{5:5}
1 lock held by swapper/0/0:
ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0
#0: ffff8000817ec298
ccree e6601000.crypto: ARM ccree device initialized
(tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8
stack backtrace:
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
Call trace:
show_stack+0x14/0x1c (C)
dump_stack_lvl+0x6c/0x90
dump_stack+0x14/0x1c
__lock_acquire+0x904/0x1584
lock_acquire+0x220/0x34c
_raw_spin_lock_irqsave+0x58/0x80
__pm_runtime_resume+0x38/0x88
sh_tmu_clock_event_set_oneshot+0x84/0xd4
clockevents_switch_state+0xfc/0x13c
tick_broadcast_set_event+0x30/0xa4
__tick_broadcast_oneshot_control+0x1e0/0x3a8
tick_broadcast_oneshot_control+0x30/0x40
cpuidle_enter_state+0x40c/0x680
cpuidle_enter+0x30/0x40
do_idle+0x1f4/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x130
do_one_initcall+0x0/0x230
__primary_switched+0x88/0x90
For non-PREEMPT_RT builds this is not really an issue, but for
PREEMPT_RT builds where normal spinlocks can sleep this might be an
issue. Be cautious and always leave the power and clock running after
probe.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251202221341.1856773-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bffacdb80b ]
cilium bpf_wiregard.bpf.c when compiled with -O1 fails to load
with the following verifier log:
192: (79) r2 = *(u64 *)(r10 -304) ; R2=pkt(r=40) R10=fp0 fp-304=pkt(r=40)
...
227: (85) call bpf_skb_store_bytes#9 ; R0=scalar()
228: (bc) w2 = w0 ; R0=scalar() R2=scalar(smin=0,smax=umax=0xffffffff,var_off=(0x0; 0xffffffff))
229: (c4) w2 s>>= 31 ; R2=scalar(smin=0,smax=umax=0xffffffff,smin32=-1,smax32=0,var_off=(0x0; 0xffffffff))
230: (54) w2 &= -134 ; R2=scalar(smin=0,smax=umax=umax32=0xffffff7a,smax32=0x7fffff7a,var_off=(0x0; 0xffffff7a))
...
232: (66) if w2 s> 0xffffffff goto pc+125 ; R2=scalar(smin=umin=umin32=0x80000000,smax=umax=umax32=0xffffff7a,smax32=-134,var_off=(0x80000000; 0x7fffff7a))
...
238: (79) r4 = *(u64 *)(r10 -304) ; R4=scalar() R10=fp0 fp-304=scalar()
239: (56) if w2 != 0xffffff78 goto pc+210 ; R2=0xffffff78 // -136
...
258: (71) r1 = *(u8 *)(r4 +0)
R4 invalid mem access 'scalar'
The error might confuse most bpf authors, since fp-304 slot had 'pkt'
pointer at insn 192 and became 'scalar' at 238. That happened because
bpf_skb_store_bytes() clears all packet pointers including those in
the stack. On the first glance it might look like a bug in the source
code, since ctx->data pointer should have been reloaded after the call
to bpf_skb_store_bytes().
The relevant part of cilium source code looks like this:
// bpf/lib/nodeport.h
int dsr_set_ipip6()
{
if (ctx_adjust_hroom(...))
return DROP_INVALID; // -134
if (ctx_store_bytes(...))
return DROP_WRITE_ERROR; // -141
return 0;
}
bool dsr_fail_needs_reply(int code)
{
if (code == DROP_FRAG_NEEDED) // -136
return true;
return false;
}
tail_nodeport_ipv6_dsr()
{
ret = dsr_set_ipip6(...);
if (!IS_ERR(ret)) {
...
} else {
if (dsr_fail_needs_reply(ret))
return dsr_reply_icmp6(...);
}
}
The code doesn't have arithmetic shift by 31 and it reloads ctx->data
every time it needs to access it. So it's not a bug in the source code.
The reason is DAGCombiner::foldSelectCCToShiftAnd() LLVM transformation:
// If this is a select where the false operand is zero and the compare is a
// check of the sign bit, see if we can perform the "gzip trick":
// select_cc setlt X, 0, A, 0 -> and (sra X, size(X)-1), A
// select_cc setgt X, 0, A, 0 -> and (not (sra X, size(X)-1)), A
The conditional branch in dsr_set_ipip6() and its return values
are optimized into BPF_ARSH plus BPF_AND:
227: (85) call bpf_skb_store_bytes#9
228: (bc) w2 = w0
229: (c4) w2 s>>= 31 ; R2=scalar(smin=0,smax=umax=0xffffffff,smin32=-1,smax32=0,var_off=(0x0; 0xffffffff))
230: (54) w2 &= -134 ; R2=scalar(smin=0,smax=umax=umax32=0xffffff7a,smax32=0x7fffff7a,var_off=(0x0; 0xffffff7a))
after insn 230 the register w2 can only be 0 or -134,
but the verifier approximates it, since there is no way to
represent two scalars in bpf_reg_state.
After fallthough at insn 232 the w2 can only be -134,
hence the branch at insn
239: (56) if w2 != -136 goto pc+210
should be always taken, and trapping insn 258 should never execute.
LLVM generated correct code, but the verifier follows impossible
path and rejects valid program. To fix this issue recognize this
special LLVM optimization and fork the verifier state.
So after insn 229: (c4) w2 s>>= 31
the verifier has two states to explore:
one with w2 = 0 and another with w2 = 0xffffffff
which makes the verifier accept bpf_wiregard.c
A similar pattern exists were OR operation is used in place of the AND
operation, the verifier detects that pattern as well by forking the
state before the OR operation with a scalar in range [-1,0].
Note there are 20+ such patterns in bpf_wiregard.o compiled
with -O1 and -O2, but they're rarely seen in other production
bpf programs, so push_stack() approach is not a concern.
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Co-developed-by: Puranjay Mohan <puranjay@kernel.org>
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20260112201424.816836-2-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b40a5d724f ]
With CONFIG_CFI enabled, the kernel strictly enforces that indirect
function calls use a function pointer type that matches the target
function. I ran into the following type mismatch when running BPF
self-tests:
CFI failure at bpf_obj_free_fields+0x190/0x238 (target:
bpf_crypto_ctx_release+0x0/0x94; expected type: 0xa488ebfc)
Internal error: Oops - CFI: 00000000f2008228 [#1] SMP
...
As bpf_crypto_ctx_release() is also used in BPF programs and using
a void pointer as the argument would make the verifier unhappy, add
a simple stub function with the correct type and register it as the
destructor kfunc instead.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Viktor Malik <vmalik@redhat.com>
Link: https://lore.kernel.org/r/20260110082548.113748-7-samitolvanen@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
