Hopefully this one will be better able to cope with moving tiled buffers
around without getting them all scrambled as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv2x CRTC FIFOs are as large as in nv3x (4kB it seems), and the FIFO
control registers have the same layout: we can make them share the
same implementation.
Previously we were using the nv1x code, but the calculated FIFO
watermarks are usually too low for nv2x and they cause horrible
scanout artifacts. They've gone unnoticed until now because we've been
leaving one of the bandwidth regs uninitialized (CRE 47, which
contains the most significant bits of FFLWM), so everything seemed to
work fine except in some cases after a cold boot, depending on the
memory bandwidth and pixel clocks used.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some nv4x cards (specifically, the ones that use an internal
PCIE->AGP bridge) the AGP controller state isn't preserved after a
suspend/resume cycle, and the AGP control registers have moved from
0x18xx to 0x100xx, so the FW check in nouveau_mem_reset_agp() doesn't
quite work. Check "dev->agp->mode" instead.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch is temporary fix to below crash. This is observed when
CPU is clocked more than 600 MHz.
Unhandled fault: imprecise external abort (0x1406) at 0xbf9ef65c
Internal error: : 1406 [#1] PREEMPT SMP
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.36-rc3+ #18)
PC is at kernel_thread_helper+0x0/0x14
LR is at kernel_thread_helper+0x0/0x14
pc : [<c003ce14>] lr : [<c003ce14>] psr: 00000093
sp : dc83bff8 ip : 00000000 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : 00000000
r7 : 00000013 r6 : c003ce28 r5 : c008935c r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7f Table: 8000404a DAC: 00000017
Process swapper (pid: 2, stack limit = 0xdc83a2f0)
Stack: (0xdc83bff8 to 0xdc83c000)
bfe0: 00000000 ffffffff
[<c003ce14>] (kernel_thread_helper+0x0/0x14) from [<fffffffe>] (0xfffffffe)
Code: c03a0ba3 c03a5fcb c045c880 c0394035 (eb017701)
---[ end trace 1b75b31a2719ed1c ]---
The timer hwmod adaptation will eventually fix it in a proper way.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On ES2.0 the L2 cache init parameter ineeds to be changed to take
care of cache size. The cache size is 1MB on ES2.0 vs 512KB on ES1.0
This patch fixes the init parameter to update the same using
dynamic cpu version check
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP4 there is no need to have SRAM_BOOTLOADER_SZ provision
Hence put this macro under CONFIG_ARCH_OMAP2PLUS check
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP24xx/34xx/44xx: omap_type() returns the correct type:
OMAP2_DEVICE_TYPE_TEST
OMAP2_DEVICE_TYPE_EMU
OMAP2_DEVICE_TYPE_SEC
OMAP2_DEVICE_TYPE_GP
OMAP2_DEVICE_TYPE_BAD
In current implementation there are two problems:
Problem 1:
For 34xx, the current if check will never return true.
Problem 2:
For 24xx the correct type check should be with omap_type() function
Verified by checking the TRM 24xx for CONTROL_STATUS register bits
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The colour was written to a wrong register for fillrect operations.
This sometimes caused empty console space (for example after 'clear')
to have a different colour than desired. Fix this by writing to the
correct register.
Many thanks to Daniel Drake and Jon Nettleton for pointing out this
issue and pointing me in the right direction for the fix.
Fixes http://dev.laptop.org/ticket/9323
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: stable@kernel.org
This patch adds documentation for the new proc interface that allows
modification of the output device configuration. Should be stable and
useful enough now for daily use.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
Now it looks like we finally know enough about the output devices to give
them proper names. As VIA_96 is often referred to as DVP0 rename it to
VIA_DVP0. As VIA_6C and VIA_93 seem to exist only on CLE266 and "replace"
DVP0 and DVP1 there rename them to VIA_LDVP0 and VIA_LDVP1 (L as legacy).
The proc names were changed accordingly which should be harmless as they
were just introduced and not beyond RFC state.
This patch should make things a bit more comfortable and less scary.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
This patch maps supported output devices to IGP versions. This list may
contain errors as most of it is derived of the driver source but it should
be correct enough to provide a good help. The devices are exported via a
proc entry in the same format as those showing the output devices per IGA.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
This patch sets the sync polarity for all output devices, not only CRT.
This may give some people a working screen but only if lcd scaling and
centering are not used as it is currently too dificult to propagate a
different resolution (from what the application thinks) to the correct
output device. Hopefully this does not introduce regressions as the
polarity of non-CRT devices was completly ignored before.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
At the moment only the sync polarity for CRT is handled but there are
also bits for controlling the sync polarity for other output devices.
Add a function to change those similar to the other output device
functions.
There is no runtime change yet as the code still handles only CRT.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch reduces the value for I2C timeout and udelay.
The udelay was reduced to 10 (old: 40) which is still very high as for
standard-mode I2C even 5 should work. This gives a speedup of factor 4
when talking to I2C devices.
The timeout was reduced to 2 (old: 20) which is taken from the radeon
driver so it should work as well. This gives a speedup of factor 10 when
detecting that there is no I2C device we want to talk to.
This causes a huge improvement of device initialization time.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch enables the I2C port to talk with the CRT. This allows adding
EDID reading and parsing capability for CRTs.
Just a small preparation, no notable changes in user experience yet.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
i2c_transfer returns negative errno on error and number of messages
processed on success. Just returning this value would give a poor
interface as it is not obvious that you must compare with 2 after reading
1 or n bytes and with 1 after writing 1 byte to determine if it was
successful. To avoid this error prone interface convert the error code
of a successful read/write to zero and all other non-negative values to
an negative error code.
This fixes a regression introduced by
via: Rationalize vt1636 detection
which resulted in no longer detecting a VT1636 chip and therefore has
broken the output in configurations which contain this chip.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
This patch merges tbl1636 into vt1636 and cleans it up as the data was
only used there anyway. No runtime changes are expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch moves common parts of dvi.c, lcd.c and vt1636.c to hw.c to
start a per output device power management. There should be no runtime
changes aside that this patch enables the proc interface to enable/disable
devices when needed which greatly increases the chances that changes to
the output device configuration will work. However the power management is
not yet complete so it might fail on some configurations. As this area is
quite complex and touches undocumented things there is a slight chance of
regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch cleans the LCD code up. It forbids overwritting global
decissions like what IGA should be used as the source and whether to
enable the second display channel. Additionally it removes a bit code
duplication.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch extends the proc entry to contain a possibility to view and
change the output devices for each IGA. This is useful for debugging
output problems as it provides a reliable way to query which low level
devices are active after VIAs output device configuration nightmare
happended. It's as well suitable for daily use as one can change the
output configuration on the fly for example to connect a projector.
At the moment it's still unstable. The reason is that we have to handle
a bunch of undocumented output devices (those without a proper name) and
that this patch is the first step to collect and verify the needed
information. Basically the only configuration change that is expected to
work at the moment is switching output devices between IGA1 and IGA2.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
This patch merges the remaining functionality of the output path
function in the associated enabling functions. This is very natural as
most of the remaining code does actually enable the device.
Just some more or less intelligent code merge. If no stupid mistakes
occured there should be no regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch uses the iga{1,2}_devices variables to select which IGA
should be the source. Doing this is convinient, more powerfull
than the older scheme and easy extendable to support further output
devices. It is not yet completed as the device on/off selection needs
to be converted to the same scheme to take full advantage.
No visible changes yet as we want to complete the transition before
anouncing any unstabke interface.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch adds a new output device management that stores for each
IGA which output devices are routed to it and a compatiblity layer
that converts the old per-output device values in the new format.
Bounding the output devices to each IGA is a central idea of the
cleanup. Doing it this way should be easier and make much more sense
than the old format which happily mixed different output devices
together and did not even take into account that some devices are no
longer available on newer chipsets.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
The result of viafb_set_iga_path can change after init only in the
hotplug ioctl. So we can move it there rather than doing it always
when a new mode is set. The setup during init is done via a call
from the init chip funtion.
This change enables a stable mapping between the old device scheme
and a new more powerfull one.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
There are a lot of init functions which are not marked as such.
Fix this.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch rips the device routing out of the 3 main functions to
separate functions to make them available for transition to a better
controlling scheme.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Move the enabling of the second display channel to the generic
output routing function and do it exactly if something is using it.
This unifies a zoo of variants how to do it and does no longer
disable it if LCD is not on the second display which is much saner
as there can be other users who need it. Probably this did not cause
any problems so far as we only recently started dual fb support and
otherwise there won't be other users and LCD is preferred assigned to
second display channel.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Move all output path routing directly in the viafb_setmode. This
gives a better overview and allows to factor similar parts out.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
This patch moves the power on/off sequences to lcd.c as they are only
used there. This allows removing lcdtbl.h as the other stuff is not
used.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Looks like we did reset the PLL of the (whatever) engine instead of
the PLL of the secondary display (IGA2, LCDCK). This patch fixes it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Joseph Chan <JosephChan@via.com.tw>
Looks like a typo from commit d6d834b010.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board file changes for the digital compass hmc5843.
The interface to the device is i2c.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Confirming page lock is held in hugetlb_add_anon_rmap() may be useful
to detect possible future problems.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "if (!trylock_page)" block in the avoidcopy path of hugetlb_cow()
looks confusing and is buggy. Originally this trylock_page() was
intended to make sure that old_page is locked even when old_page !=
pagecache_page, because then only pagecache_page is locked.
This patch fixes it by moving page locking into hugetlb_fault().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Obviously, setting anon_vma for COWed hugepage should be done
by hugepage_add_new_anon_rmap() to scan vmas faster.
This patch fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>