Embed a copy of struct wm8962_pdata in stuct wm8962_priv
so that there's no need to check validity of pdata any more.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.
v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incomplete since ilk+ support needs proper pch dpll tracking first.
SDVO get_config parts based on a patch from Jesse Barnes, but fixed up
to actually work.
v2: Make sure that we call encoder->get_config _after_ we
get_pipe_config to be consistent in both setup_hw_state and the
modeset state checker. Otherwise the clever trick with handling the
pixel mutliplier on i915G/GM where the encoder overrides the default
value of 1 from the crtc get_pipe_config function doesn't work.
Spotted by Imre Deak.
v3: Actually cross-check the pixel mutliplier (but not on pch split
platforms for now). Now actually also tested on a i915G with a sdvo
encoder plugged in.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a codec is powered off, some systems don't respond properly after
D3 FG transition, while the driver still expects the response and
tries to fall back to different modes (polling and single-cmd). When
the fallback happens, the driver stays in that mode, and falling back
to the single-cmd mode means it'll loose the unsol event handling,
too.
The unresponsiveness at D3 isn't too serious, thus this fallback is
mostly superfluous. We can gracefully ignore the error there so that
the driver keeps the normal operation mode.
This patch adds a new bit flag for codec read/write, set in the power
transition stage, which is notified to the controller driver via a new
bus->no_response_fallback flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_read(), snd_hda_codec_write() & co take the argument
"direct" that indicates whether the given NID is a direct reference or
an indirect reference. However, the indirect reference is practically
unimplemented and never exists. And moreover, we don't need the
indication of indirect reference at this high level, as NID can be
represented in 16bit values at this point.
Meanwhile, there are some cases where it'd be nice to give some
operational options to these functions. So, we can reuse this
argument as a new bit flag! Pretty frugal, eh?
All callers so far pass zero to this argument, thus there is no
behavior change by this replacement.
The real usage of this new bit option will be added in the following
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding more context from Ville's reply to Rodrigo's question why we
need this:
"The spec says that on some hardware you need to PLL running before you
can poke at the palette registers. I didn't actually try to anger the
hardware so I'm not really sure what would happen otherwise, but IIRC
Jesse said something about a hard system hang..."
And generally documenting such ordering constraints with asserts is
Just Good.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Spruce up the commit message a lot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make assert_sprites_disabled() operational on all platforms where
we currently have sprite support enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ever since gen4 primary planes were fixed to pipes.
And for gen2-3, don't check plane B if it doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable/restore sprite planes around mode-set just like we do for the
primary and cursor planes. Now that we have working sprite clipping,
this actually works quite decently.
Previosuly we didn't even bother to disable sprites when changing mode,
which could lead to a corrupted sprite appearing on the screen after a
modeset (at least on my IVB). Not sure if all hardware generations would
be so forgiving when enabled sprites end up outside the pipe dimensons.
v2: Disable rather than enable sprites in ironlake_crtc_disable()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV doesn't have the old video overlay.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First disable FBC, then IPS, then disable all planes, and finally
disable the pipe.
v2: Mention IPS in the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again follow the same sequence for all generations, because doing
otherwise just doesn't make sense.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the same sequence when enabling the cursor plane during
modeset. No point in doing this stuff in different order on different
generations.
This should also avoid a needless wait for vblank for the g4x cursor
workaround when the cursor gets enabled anyway.
Acked-by: Egbert Eich <eich@suse.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Loading the palette after the planes are enabled can risk showing
incorrect colors. ILK+ already load the palette before even the pipe
is enabled. Just follow the same order for gen2-4 and VLV.
According to BSpec the requirements for palette access are
display core clock and display PLL running. In certain platforms
just the core clock may be enough. But we definitely should have both
running when this gets called during the modeset.
v2: Amend the commit message with some display PLL/core clock info
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Masking events on MMCIF means that an occurrence of the masked event
won't raise an interrupt, but the event bit will still be set in the
interrupt status register. If simultaneously a different event occurs
which was enabled, both flags will be set. However, only the unmasked
event bit should be cleared in the status register in such a case.
Clearing also the masked bit can lead to lost interrupts, which indeed
can be observed on the armadillo800eva r8a7740 board with an eMMC chip.
The problem has been introduced by the recent "mmc: sh_mmcif: simplify
IRQ processing" patch. Fix the problem by only clearing enabled interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When resuming, the tmio_mmc_host_resume() function is run when the
controller might still be powered down. Issuing a reset command to it at
that time has no effect. This patch postpones resetting the controller
until the first powering-up .set_ios() call.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So we can remove some duplicate code. All the PCHs are very similar
and right now the code is the same. I plan to add more code, so we
would have more duplicated code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently HDMI codec driver sets the hard dependency (reverse
selection) on CONFIG_SND_DYNAMIC_MINORS because the recent codecs may
support more than two PCMs. But, this doesn't mean that we need
always this option, since there can be a single PCM stream even with
the modern codecs.
This patch drops the hard dependency again but give more sensible
error message when no enough PCMs are available due to the lack of
this option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise the functions will be defined but unreferenced when runtime PM
is disabled, generating warnings.
Signed-off-by: Mark Brown <broonie@linaro.org>
If kthread_run() fails, init_threads() returns
IS_ERR(p) instead of PTR_ERR(p).
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
By stashing a pointer of who opened the device and keeping a list of
open fd, we can then walk each client and inspect how many objects they
have open. For example,
i915_gem_objects:
1102 objects, 613646336 bytes
663 [662] objects, 468783104 [468750336] bytes in gtt
37 [37] active objects, 46874624 [46874624] bytes
626 [625] inactive objects, 421908480 [421875712] bytes
282 unbound objects, 6512640 bytes
85 purgeable objects, 6787072 bytes
28 pinned mappable objects, 3686400 bytes
40 fault mappable objects, 27783168 bytes
2145386496 [536870912] gtt total
Xorg: 43 objects, 32243712 bytes (10223616 active, 16683008 inactive, 4096 unbound)
gnome-shell: 30 objects, 28381184 bytes (0 active, 28336128 inactive, 0 unbound)
xonotic-linux64: 1032 objects, 569933824 bytes (46874624 active, 383545344 inactive, 6508544 unbound)
v2: Use existing drm->filelist as pointed out by Ben.
v3: Not even stashing the task_struct is required as Ben pointed out
drm_file->pid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Conflicts:
net/netfilter/nf_log.c
The conflict in nf_log.c is that in 'net' we added CONFIG_PROC_FS
protection around foo_proc_entry() calls to fix a build failure,
whereas in Pablo's tree a guard if() test around a call is
remove_proc_entry() was removed. Trivially resolved.
Pablo Neira Ayuso says:
====================
The following patchset contains the first batch of
Netfilter/IPVS updates for your net-next tree, they are:
* Three patches with improvements and code refactorization
for nfnetlink_queue, from Florian Westphal.
* FTP helper now parses replies without brackets, as RFC1123
recommends, from Jeff Mahoney.
* Rise a warning to tell everyone about ULOG deprecation,
NFLOG has been already in the kernel tree for long time
and supersedes the old logging over netlink stub, from
myself.
* Don't panic if we fail to load netfilter core framework,
just bail out instead, from myself.
* Add cond_resched_rcu, used by IPVS to allow rescheduling
while walking over big hashtables, from Simon Horman.
* Change type of IPVS sysctl_sync_qlen_max sysctl to avoid
possible overflow, from Zhang Yanfei.
* Use strlcpy instead of strncpy to skip zeroing of already
initialized area to write the extension names in ebtables,
from Chen Gang.
* Use already existing per-cpu notrack object from xt_CT,
from Eric Dumazet.
* Save explicit socket lookup in xt_socket now that we have
early demux, also from Eric Dumazet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert code to use DEFINE_RES_MEM*() macros.
These macros were already used in this file,
this change makes their usage consistent throughout the file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The correct model name is R-Car M1A or R8A77781; R8A77780 corresponds to R-Car
M1S which is a SH based SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: manually applied]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If pdata is NULL, atmel_tsadcc_probe() will release all the resources
and return 0, but we need a error code is returned in this case.
Fix to return -EINVAL and move the check for pdata to the begin
of this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The command and status register in the driver were swapped with
respect to the order specified in the datasheet (CY8CTMA140).
Confirmed with Cypress that the order in the datasheet is correct.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For the devices that has blocking with timeout communication, these
extra handshakes will prevent one timeout delay in startup sequence
Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
memcpy param is wrong because of offset in bl_cmd, this may corrupt the
stack which may cause a crash.
Tested-by: Ferruh Yigit <fery@cypress.com> on TMA300-DVK
Signed-off-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the function get_victim_by_default, where it checks
for the condition that p.min_segno != NULL_SEGNO as
shown:
if (p.min_segno != NULL_SEGNO)
goto got_it;
and if above condition is true then
got_it:
if (p.min_segno != NULL_SEGNO) {
So this condition is being checked twice. Hence move the goto
statement after the if condition so that duplication of condition
check is avoided.
Also this function makes a call to get_max_cost() to compute
the max cost based on the f2fs_sbi_info and victim policy. Since
get_max_cost depends on on three parameters of victim_sel_policy
=> alloc_mode, gc_mode & ofs_unit, once this victim policy is
initialised, these value will not change till the execution
time of get_victim_by_default() & also f2fs_sbi_info structure
parameters will not change.
Hence making calls to get_max_cost() in while loop does not seems to
be a good point. Instead we can call it once in begining and store
the results in local variable, which later can serve our purpose
for comparing the cost with max cost inside the while loop.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Both clock-r8a7740.c and clock-r8a7790.c define a div4_clks array as
non-static. Compiling support for both SoCs thus result in a symbol
redefinition. Fix it by defining the arrays as static.
To avoid further similar issues, also define the main_clks as static.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When host ping its peer, ICMP echo request packet triggers IPsec
policy, then host negotiates SA secret with its peer. After IKE
installed SA for OUT direction, but before SA for IN direction
installed, host get ICMP echo reply from its peer. At the time
being, the SA state for IN direction could be XFRM_STATE_ACQ,
then the received packet will be dropped after adding
LINUX_MIB_XFRMINSTATEINVALID statistic.
Adding a LINUX_MIB_XFRMACQUIREERROR statistic counter for such
scenario when SA in larval state is much clearer for user than
LINUX_MIB_XFRMINSTATEINVALID which indicates the SA is totally
bad.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We add an empty irqchip_init dummy function for cases in which
CONFIG_IRQCHIP is not used. In these cases irqchip.c is not compiled,
but a funtion call may still be present in architecture code, that in
runtime doesn't get hit.
E.g. this is needed in the arch/arm/mach-shmobile/intc-r8a7740.c
interrupt setup code where OF use and non OF us is both handled in one
file.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
[horms+renesas@verge.net.au: Make non-CONFIG_IRQCHIP version static inline
and remove trailing ';'.]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The code in goto err3 path is wrong because it will call fee_irq() with k == 0,
which means it does free_irq(p->irq[-1].requested_irq, &p->irq[-1]);
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since the introduction of preemptible mmu_gather TLB fast mode has been
broken. TLB fast mode relies on there being absolutely no concurrency;
it frees pages first and invalidates TLBs later.
However now we can get concurrency and stuff goes *bang*.
This patch removes all tlb_fast_mode() code; it was found the better
option vs trying to patch the hole by entangling tlb invalidation with
the scheduler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kbuild fixes from Michal Marek:
"There is one fix for a kbuild regression, plus three kconfig fixes for
bugs that have alway been there, but are simple enough to be fixed in
an -rc"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig/menu.c: fix multiple references to expressions in menu_add_prop()
mconf: handle keys in empty dialogs
kbuild: Don't assume dts files live in arch/*/boot/dts
scripts/config: fix assignment of parameters for short version of --*-after options
Adds abitilty to tune L1 timeout (inactivity timer for usb2 link sleep)
and BESL (best effort service latency)via sysfs.
This also adds a new usb2_lpm_parameters structure with those variables to
struct usb_device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well
BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.
Now instead cache the capability values and check them for each port individually
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
According to Felipe and Alan's comments the second parameter of irq
handler should be 'void *' not a specific structure pointer.
So change it.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When CONFIG_XHCI_HCD_DEBUGGING is activated, the XHCI driver can dump
device and input contexts to the console. The endpoint contexts in that
dump are labeled "Endpoint N Context", where N is the XHCI endpoint
index (DCI - 1). This can be very confusing, especially for people who
are not that familiar with the XHCI specification. This patch introduces
an xhci_get_endpoint_address function (as a counterpart to the reverse
xhci_get_endpoint_index), and uses it to additionally display the
endpoint number and direction when dumping contexts, which are much more
commonly used concepts in USB.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the debugfs_create_xxx() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The smp_init_cpus method in the smp_operations structure is optional
and can be omitted entirely.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU and cluster numbers (MPIDR affinity levels 0 and 1) may have
at most 8 bits each.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently flush_dcache_page() thinks pages as non-mapped if
mapping_mapped(mapping) return false. This approach is very
coase:
- mmap on part of file may cause all pages backed on
the file being thought as mmaped
- file-backed pages aren't mapped into user space actually
if the memory mmaped on the file isn't accessed
This patch uses page_mapped() to decide if the page has been
mapped.
From the attached test code, I find there is much performance
improvement(>25%) when accessing page caches via read under this
situations, so memcpy benefits a lot from not flushing cache
under this situation.
No. read time without the patch No. read time with the patch
================================================================
No. 0, time 22615636 us No. 0, time 22014717 us
No. 1, time 4387851 us No. 1, time 3113184 us
No. 2, time 4276535 us No. 2, time 3005244 us
No. 3, time 4259821 us No. 3, time 3001565 us
No. 4, time 4263811 us No. 4, time 3002748 us
No. 5, time 4258486 us No. 5, time 3004104 us
No. 6, time 4253009 us No. 6, time 3002188 us
No. 7, time 4262809 us No. 7, time 2998196 us
No. 8, time 4264525 us No. 8, time 3007255 us
No. 9, time 4267795 us No. 9, time 3005094 us
1), No.0. is to read the file from storage device, and others are
to read the file from page caches basically.
2), file size is 512M, and is on ext4 over usb mass storage.
3), the test is done on Pandaboard.
unsigned int sum = 0;
unsigned long sum_val = 0;
static unsigned long tv_diff(struct timeval *tv1, struct timeval *tv2)
{
return (tv2->tv_sec - tv1->tv_sec) * 1000000 +
(tv2->tv_usec - tv1->tv_usec);
}
int main(int argc, char *argv[])
{
char *mbuf, fbuf;
int fd;
int i;
unsigned long page_size, size;
struct stat stat;
struct timeval t1, t2;
unsigned char *rbuf = malloc(32 * page_size);
if (!rbuf) {
printf(" %sn", "malloc failed");
exit(-1);
}
page_size = getpagesize();
fd = open(argv[1], O_RDWR);
assert(fd >= 0);
fstat(fd, &stat);
size = stat.st_size;
printf("%s: file %s, size %lu, page size %lun",
argv[0],
argv[1], size, page_size);
gettimeofday(&t1, NULL);
mbuf = mmap(NULL, size, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0);
if (!mbuf) {
printf(" %sn", "mmap failed");
exit(-1);
}
for (i = 0 ; i < size ; i += (page_size * 32)) {
int rcnt;
lseek(fd, i, SEEK_SET);
rcnt = read(fd, rbuf, page_size * 32);
if (rcnt != page_size * 32) {
printf("%s: read faildn", __func__);
exit(-1);
}
}
free(rbuf);
munmap(mbuf, size);
gettimeofday(&t2, NULL);
printf("tread mmaped time: %luusn", tv_diff(&t1, &t2));
close(fd);
}
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch replaces macro rx_hal_is_cck_rate() with
the static inline function rx_hal_is_cck_rate().
This replacement was suggested by Dan Carpenter and
has the following benefits:
- improves code readability
- guarantees type safety
- improves code efficiency by enforcing the evaluation of
the simple boolean expression (!pdrvinfo->RxHT) to be
done before the evaluation of the more complex one
(pdrvinfo->RxRate == DESC90_RATE1M ||
pdrvinfo->RxRate == DESC90_RATE2M ||
pdrvinfo->RxRate == DESC90_RATE5_5M ||
pdrvinfo->RxRate == DESC90_RATE11M)
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
