commit e4fc307d8e upstream.
This reverts commit 864f9963ec.
The patch is wrong as it checks vc_origin against vc_screenbuf,
while in text mode it should compare against vga_vram_base.
As such it broke VGA text scrolling, which can be reproduced like this:
(1) boot a kernel that is configured to use text mode VGA-console
(2) type commands: ls -l /usr/bin | less -S
(3) scroll up/down with cursor-down/up keys
Reported-by: Jari Ruusu <jariruusu@protonmail.com>
Cc: stable@vger.kernel.org
Cc: Yi Yang <yiyang13@huawei.com>
Cc: GONG Ruiqi <gongruiqi1@huawei.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a091a58b8a upstream.
octeontx2 crypto driver allocates memory using kmalloc/kzalloc,
and uses this memory for dma (does dma_map_single()). It assumes
that kmalloc/kzalloc will return 128-byte aligned address. But
kmalloc/kzalloc returns 8-byte aligned address after below changes:
"9382bc44b5 arm64: allow kmalloc() caches aligned to the
smaller cache_line_size()
Memory allocated are used for following purpose:
- Input data or scatter list address - 8-Byte alignment
- Output data or gather list address - 8-Byte alignment
- Completion address - 32-Byte alignment.
This patch ensures all addresses are aligned as mentioned above.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Cc: <stable@vger.kernel.org> # v6.8+
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e13163b43 upstream.
octeontx2 crypto driver allocates memory using kmalloc/kzalloc,
and uses this memory for dma (does dma_map_single()). It assumes
that kmalloc/kzalloc will return 128-byte aligned address. But
kmalloc/kzalloc returns 8-byte aligned address after below changes:
"9382bc44b5 arm64: allow kmalloc() caches aligned to the
smaller cache_line_size()
Memory allocated are used for following purpose:
- Input data or scatter list address - 8-Byte alignment
- Output data or gather list address - 8-Byte alignment
- Completion address - 32-Byte alignment.
This patch ensures all addresses are aligned as mentioned above.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Cc: <stable@vger.kernel.org> # v6.5+
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7b88b4939 upstream.
octeontx2 crypto driver allocates memory using kmalloc/kzalloc,
and uses this memory for dma (does dma_map_single()). It assumes
that kmalloc/kzalloc will return 128-byte aligned address. But
kmalloc/kzalloc returns 8-byte aligned address after below changes:
"9382bc44b5 arm64: allow kmalloc() caches aligned to the
smaller cache_line_size()"
Completion address should be 32-Byte alignment when loading
microcode.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Cc: <stable@vger.kernel.org> # v6.5+
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d4df408ba upstream.
Repeated loading and unloading of a device specific QAT driver, for
example qat_4xxx, in a tight loop can lead to a crash due to a
use-after-free scenario. This occurs when a power management (PM)
interrupt triggers just before the device-specific driver (e.g.,
qat_4xxx.ko) is unloaded, while the core driver (intel_qat.ko) remains
loaded.
Since the driver uses a shared workqueue (`qat_misc_wq`) across all
devices and owned by intel_qat.ko, a deferred routine from the
device-specific driver may still be pending in the queue. If this
routine executes after the driver is unloaded, it can dereference freed
memory, resulting in a page fault and kernel crash like the following:
BUG: unable to handle page fault for address: ffa000002e50a01c
#PF: supervisor read access in kernel mode
RIP: 0010:pm_bh_handler+0x1d2/0x250 [intel_qat]
Call Trace:
pm_bh_handler+0x1d2/0x250 [intel_qat]
process_one_work+0x171/0x340
worker_thread+0x277/0x3a0
kthread+0xf0/0x120
ret_from_fork+0x2d/0x50
To prevent this, flush the misc workqueue during device shutdown to
ensure that all pending work items are completed before the driver is
unloaded.
Note: This approach may slightly increase shutdown latency if the
workqueue contains jobs from other devices, but it ensures correctness
and stability.
Fixes: e5745f3411 ("crypto: qat - enable power management for QAT GEN4")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ahsan Atta <ahsan.atta@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ffc47fedd upstream.
Since the CAAM on these SoCs is managed by another ARM core, called the
SECO (Security Controller) on iMX8QM and Secure Enclave on iMX8ULP, which
also reserves access to register page 0 suspend operations cannot touch
this page.
This is similar to when running OPTEE, where OPTEE will reserve page 0.
Track this situation using a new state variable no_page0, reflecting if
page 0 is reserved elsewhere, either by other management cores in SoC or
by OPTEE.
Replace the optee_en check in suspend/resume with the new check.
optee_en cannot go away as it's needed elsewhere to gate OPTEE specific
situations.
Fixes the following splat at suspend:
Internal error: synchronous external abort: 0000000096000010 [#1] SMP
Hardware name: Freescale i.MX8QXP ACU6C (DT)
pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : readl+0x0/0x18
lr : rd_reg32+0x18/0x3c
sp : ffffffc08192ba20
x29: ffffffc08192ba20 x28: ffffff8025190000 x27: 0000000000000000
x26: ffffffc0808ae808 x25: ffffffc080922338 x24: ffffff8020e89090
x23: 0000000000000000 x22: ffffffc080922000 x21: ffffff8020e89010
x20: ffffffc080387ef8 x19: ffffff8020e89010 x18: 000000005d8000d5
x17: 0000000030f35963 x16: 000000008f785f3f x15: 000000003b8ef57c
x14: 00000000c418aef8 x13: 00000000f5fea526 x12: 0000000000000001
x11: 0000000000000002 x10: 0000000000000001 x9 : 0000000000000000
x8 : ffffff8025190870 x7 : ffffff8021726880 x6 : 0000000000000002
x5 : ffffff80217268f0 x4 : ffffff8021726880 x3 : ffffffc081200000
x2 : 0000000000000001 x1 : ffffff8020e89010 x0 : ffffffc081200004
Call trace:
readl+0x0/0x18
caam_ctrl_suspend+0x30/0xdc
dpm_run_callback.constprop.0+0x24/0x5c
device_suspend+0x170/0x2e8
dpm_suspend+0xa0/0x104
dpm_suspend_start+0x48/0x50
suspend_devices_and_enter+0x7c/0x45c
pm_suspend+0x148/0x160
state_store+0xb4/0xf8
kobj_attr_store+0x14/0x24
sysfs_kf_write+0x38/0x48
kernfs_fop_write_iter+0xb4/0x178
vfs_write+0x118/0x178
ksys_write+0x6c/0xd0
__arm64_sys_write+0x14/0x1c
invoke_syscall.constprop.0+0x64/0xb0
do_el0_svc+0x90/0xb0
el0_svc+0x18/0x44
el0t_64_sync_handler+0x88/0x124
el0t_64_sync+0x150/0x154
Code: 88dffc21 88dffc21 5ac00800 d65f03c0 (b9400000)
Fixes: d2835701d9 ("crypto: caam - i.MX8ULP donot have CAAM page0 access")
Cc: stable@kernel.org # v6.10+
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8024774190 upstream.
Most kernel applications utilizing the crypto API operate synchronously
and on small buffer sizes, therefore do not benefit from QAT acceleration.
Reduce the priority of QAT implementations for both skcipher and aead
algorithms, allowing more suitable alternatives to be selected by default.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Link: https://lore.kernel.org/all/20250613012357.GA3603104@google.com/
Cc: stable@vger.kernel.org
Acked-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22375adaa0 upstream.
The MIPS32r2 ChaCha code has never been buildable with the clang
assembler. First, clang doesn't support the 'rotl' pseudo-instruction:
error: unknown instruction, did you mean: rol, rotr?
Second, clang requires that both operands of the 'wsbh' instruction be
explicitly given:
error: too few operands for instruction
To fix this, align the code with the real instruction set by (1) using
the real instruction 'rotr' instead of the nonstandard pseudo-
instruction 'rotl', and (2) explicitly giving both operands to 'wsbh'.
To make removing the use of 'rotl' a bit easier, also remove the
unnecessary special-casing for big endian CPUs at
.Lchacha_mips_xor_bytes. The tail handling is actually
endian-independent since it processes one byte at a time. On big endian
CPUs the old code byte-swapped SAVED_X, then iterated through it in
reverse order. But the byteswap and reverse iteration canceled out.
Tested with chacha20poly1305-selftest in QEMU using "-M malta" with both
little endian and big endian mips32r2 kernels.
Fixes: 49aa7c00ed ("crypto: mips/chacha - import 32r2 ChaCha code from Zinc")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505080409.EujEBwA0-lkp@intel.com/
Link: https://lore.kernel.org/r/20250619225535.679301-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b43cb4ff85 upstream.
The maximum number of keycodes got bumped to 256 a very long time ago,
but the default keymaps were never adjusted to match. This is causing
the kernel to interpret keycodes above 127 as U+0000 if the shipped
generated keymap is used.
Fix this by mapping all keycodes above 127 to K_HOLE so the kernel
ignores them.
The contents of this patche were generated by rerunning `loadkeys
--mktable --unicode` and only including the changes to map keycodes
above 127 to K_HOLE.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-2-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1cc2092ea upstream.
We don't process Unicode characters if the virtual terminal is in raw
mode, so there's no reason why we shouldn't do the same for K_OFF
(especially since people would expect K_OFF to actually turn off all VT
key processing).
Fixes: 9fc3de9c83 ("vt: Add virtual console keyboard mode OFF")
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20250702-vt-misc-unicode-fixes-v1-1-c27e143cc2eb@qtmlabs.xyz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bd398e20f upstream.
When a remote device sends a completion event to the host, it contains a
pointer to the consumed TRE. The host uses this pointer to process all of
the TREs between it and the host's local copy of the ring's read pointer.
This works when processing completion for chained transactions, but can
lead to nasty results if the device sends an event for a single-element
transaction with a read pointer that is multiple elements ahead of the
host's read pointer.
For instance, if the host accesses an event ring while the device is
updating it, the pointer inside of the event might still point to an old
TRE. If the host uses the channel's xfer_cb() to directly free the buffer
pointed to by the TRE, the buffer will be double-freed.
This behavior was observed on an ep that used upstream EP stack without
'commit 6f18d174b7 ("bus: mhi: ep: Update read pointer only after buffer
is written")'. Where the device updated the events ring pointer before
updating the event contents, so it left a window where the host was able to
access the stale data the event pointed to, before the device had the
chance to update them. The usual pattern was that the host received an
event pointing to a TRE that is not immediately after the last processed
one, so it got treated as if it was a chained transaction, processing all
of the TREs in between the two read pointers.
This commit aims to harden the host by ensuring transactions where the
event points to a TRE that isn't local_rp + 1 are chained.
Fixes: 1d3173a3ba ("bus: mhi: core: Add support for processing events from client device")
Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com>
[mani: added stable tag and reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250714163039.3438985-1-quic_yabdulra@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f471578e8b upstream.
On big endian platform like PowerPC, the MHI bus (which is little endian)
does not start properly. The following example shows the error messages by
using QCN9274 WLAN device with ath12k driver:
ath12k_pci 0001:01:00.0: BAR 0: assigned [mem 0xc00000000-0xc001fffff 64bit]
ath12k_pci 0001:01:00.0: MSI vectors: 1
ath12k_pci 0001:01:00.0: Hardware name: qcn9274 hw2.0
ath12k_pci 0001:01:00.0: failed to set mhi state: POWER_ON(2)
ath12k_pci 0001:01:00.0: failed to start mhi: -110
ath12k_pci 0001:01:00.0: failed to power up :-110
ath12k_pci 0001:01:00.0: failed to create soc core: -110
ath12k_pci 0001:01:00.0: failed to init core: -110
ath12k_pci: probe of 0001:01:00.0 failed with error -110
The issue seems to be with the incorrect DMA address/size used for
transferring the firmware image over BHI. So fix it by converting the DMA
address and size of the BHI vector table to little endian format before
sending them to the device.
Fixes: 6cd330ae76 ("bus: mhi: core: Add support for ringing channel/event ring doorbells")
Signed-off-by: Alexander Wilhelm <alexander.wilhelm@westermo.com>
[mani: added stable tag and reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Reviewed-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250519145837.958153-1-alexander.wilhelm@westermo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 086a0e516f upstream.
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93b400f495 upstream.
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1473e9e767 upstream.
Make sure to drop the reference to the control device taken by
of_find_device_by_node() during probe when the driver is unbound.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Cc: stable@vger.kernel.org # 3.13
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 868837b0a9 upstream.
Make sure to drop the reference to the companion device taken during
probe when the driver is unbound.
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Cc: stable@vger.kernel.org # 4.19
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d1b02e5d7 upstream.
After a recent change in clang to expose uninitialized warnings from
const variables [1], there is a warning in cxacru_heavy_init():
drivers/usb/atm/cxacru.c:1104:6: error: variable 'bp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1113:39: note: uninitialized use occurs here
1113 | cxacru_upload_firmware(instance, fw, bp);
| ^~
drivers/usb/atm/cxacru.c:1104:2: note: remove the 'if' if its condition is always true
1104 | if (instance->modem_type->boot_rom_patch) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/atm/cxacru.c:1095:32: note: initialize the variable 'bp' to silence this warning
1095 | const struct firmware *fw, *bp;
| ^
| = NULL
While the warning is technically correct that bp is conditionally passed
uninitialized to cxacru_upload_firmware(), it is ultimately a false
positive warning on the uninitialized use of bp because the same
condition that initializes bp, instance->modem_type->boot_rom_patch, is
the same one that gates the use of bp within cxacru_upload_firmware().
As this warning occurs in clang's frontend before inlining occurs, it
cannot know that these conditions are indentical to avoid the warning.
Manually inline cxacru_upload_firmware() into cxacru_heavy_init(), as
that is its only callsite, so that clang can see that bp is initialized
and used under the same condition, clearing up the warning without any
functional changes to the code (LLVM was already doing this inlining
later).
Cc: stable@vger.kernel.org
Fixes: 1b0e614652 ("[PATCH] USB ATM: driver for the Conexant AccessRunner chipset cxacru")
Closes: https://github.com/ClangBuiltLinux/linux/issues/2102
Link: 2464313eef [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250722-usb-cxacru-fix-clang-21-uninit-warning-v2-1-6708a18decd2@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 210a1ce8ed upstream.
Move the cursor position rightward after rendering the character,
not before. This avoids complications that arise when the recursive
console_putc call has to wrap the line and/or scroll the display.
This also fixes the linewrap bug that crops off the rightmost column.
When the cursor is at the bottom of the display, a linefeed will not
move the cursor position further downward. Instead, the display scrolls
upward. Avoid the repeated add/subtract sequence by way of a single
subtraction at the initialization of console_struct_num_rows.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/9d4e8c68a456d5f2bc254ac6f87a472d066ebd5e.1743115195.git.fthain@linux-m68k.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 409f9287da upstream.
DM targets must not split zone append and write operations using
dm_accept_partial_bio() as doing so is forbidden for zone append BIOs,
breaks zone append emulation using regular write BIOs and potentially
creates deadlock situations with queue freeze operations.
Modify dm_accept_partial_bio() to add missing BUG_ON() checks for all
these cases, that is, check that the BIO is a write or write zeroes
operation. This change packs all the zone related checks together under
a static_branch_unlikely(&zoned_enabled) and done only if the target is
a zoned device.
Fixes: f211268ed1 ("dm: Use the block layer zone append emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Link: https://lore.kernel.org/r/20250625093327.548866-6-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e549663849 upstream.
Read and write operations issued to a dm-crypt target may be split
according to the dm-crypt internal limits defined by the max_read_size
and max_write_size module parameters (default is 128 KB). The intent is
to improve processing time of large BIOs by splitting them into smaller
operations that can be parallelized on different CPUs.
For zoned dm-crypt targets, this BIO splitting is still done but without
the parallel execution to ensure that the issuing order of write
operations to the underlying devices remains sequential. However, the
splitting itself causes other problems:
1) Since dm-crypt relies on the block layer zone write plugging to
handle zone append emulation using regular write operations, the
reminder of a split write BIO will always be plugged into the target
zone write plugged. Once the on-going write BIO finishes, this
reminder BIO is unplugged and issued from the zone write plug work.
If this reminder BIO itself needs to be split, the reminder will be
re-issued and plugged again, but that causes a call to a
blk_queue_enter(), which may block if a queue freeze operation was
initiated. This results in a deadlock as DM submission still holds
BIOs that the queue freeze side is waiting for.
2) dm-crypt relies on the emulation done by the block layer using
regular write operations for processing zone append operations. This
still requires to properly return the written sector as the BIO
sector of the original BIO. However, this can be done correctly only
and only if there is a single clone BIO used for processing the
original zone append operation issued by the user. If the size of a
zone append operation is larger than dm-crypt max_write_size, then
the orginal BIO will be split and processed as a chain of regular
write operations. Such chaining result in an incorrect written sector
being returned to the zone append issuer using the original BIO
sector. This in turn results in file system data corruptions using
xfs or btrfs.
Fix this by modifying get_max_request_size() to always return the size
of the BIO to avoid it being split with dm_accpet_partial_bio() in
crypt_map(). get_max_request_size() is renamed to
get_max_request_sectors() to clarify the unit of the value returned
and its interface is changed to take a struct dm_target pointer and a
pointer to the struct bio being processed. In addition to this change,
to ensure that crypt_alloc_buffer() works correctly, set the dm-crypt
device max_hw_sectors limit to be at most
BIO_MAX_VECS << PAGE_SECTORS_SHIFT (1 MB with a 4KB page architecture).
This forces DM core to split write BIOs before passing them to
crypt_map(), and thus guaranteeing that dm-crypt can always accept an
entire write BIO without needing to split it.
This change does not have any effect on the read path of dm-crypt. Read
operations can still be split and the BIO fragments processed in
parallel. There is also no impact on the performance of the write path
given that all zone write BIOs were already processed inline instead of
in parallel.
This change also does not affect in any way regular dm-crypt block
devices.
Fixes: f211268ed1 ("dm: Use the block layer zone append emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Link: https://lore.kernel.org/r/20250625093327.548866-5-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51888393cc upstream.
For all practical purposes, there is no difference between the situation
in which a given device is not ignoring children and its active child
count is nonzero and the situation in which its runtime PM usage counter
is nonzero. However, pm_runtime_get_if_in_use() will only increment the
device's usage counter and return 1 in the latter case.
For consistency, make it do so in the former case either by adjusting
pm_runtime_get_conditional() and update the related kerneldoc comments
accordingly.
Fixes: c111566bea ("PM: runtime: Add pm_runtime_get_if_active()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+: c0ef3df8db: PM: runtime: Simplify pm_runtime_get_if_active() usage
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Link: https://patch.msgid.link/12700973.O9o76ZdvQC@rjwysocki.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e237495346 upstream.
The blocking notifier is registered in cros_ec_register(); however, it
isn't unregistered in cros_ec_unregister().
Fix it.
Fixes: 42cd0ab476 ("platform/chrome: cros_ec: Query EC protocol version if EC transitions between RO/RW")
Cc: stable@vger.kernel.org
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20250722120513.234031-1-tzungbi@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a26df2332 upstream.
The freq_tables[] array has num_possible_cpus() elements so, to avoid an
out of bounds access, this loop should be capped at "< nb_cpus" instead
of "<= nb_cpus". The freq_tables[] array is allocated in
armada_8k_cpufreq_init().
Cc: stable@vger.kernel.org
Fixes: f525a67053 ("cpufreq: ap806: add cpufreq driver for Armada 8K")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed62a62a18 upstream.
Improve the description of the possible default SATA link power
management policies and add the missing description for policy 5.
No functional changes.
Fixes: a5ec5a7bfd ("ata: ahci: Support state with min power but Partial low power state")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f8fdd4dbf upstream.
When the PSLVERR_RESP_EN parameter is set to 1, the device generates
an error response if an attempt is made to read an empty RBR (Receive
Buffer Register) while the FIFO is enabled.
In serial8250_do_startup(), calling serial_port_out(port, UART_LCR,
UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes
dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter
function enables the FIFO via serial_out(p, UART_FCR, p->fcr).
Execution proceeds to the serial_port_in(port, UART_RX).
This satisfies the PSLVERR trigger condition.
When another CPU (e.g., using printk()) is accessing the UART (UART
is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) ==
(lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter
dw8250_force_idle().
Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock
to fix this issue.
Panic backtrace:
[ 0.442336] Oops - unknown exception [#1]
[ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a
[ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e
...
[ 0.442416] console_on_rootfs+0x26/0x70
Fixes: c49436b657 ("serial: 8250_dw: Improve unwritable LCR workaround")
Link: https://lore.kernel.org/all/84cydt5peu.fsf@jogness.linutronix.de/T/
Signed-off-by: Yunhui Cui <cuiyunhui@bytedance.com>
Reviewed-by: John Ogness <john.ogness@linutronix.de>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250723023322.464-2-cuiyunhui@bytedance.com
[ adapted to inline code structure without separate serial8250_initialize helper function ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9f58d3572 upstream.
If CONFIG_ACPI_SPCR_TABLE is disabled, acpi_parse_spcr()
currently returns 0, which may incorrectly suggest that
SPCR parsing was successful. This patch changes the behavior
to return -ENODEV to clearly indicate that SPCR support
is not available.
This prepares the codebase for future changes that depend
on acpi_parse_spcr() failure detection, such as suppressing
misleading console messages.
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/20250620131309.126555-2-me@linux.beauty
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3202ca2215 upstream.
The Supported Link Speeds Vector in the Link Capabilities 2 Register
indicates the *supported* link speeds. The Max Link Speed field in the
Link Capabilities Register indicates the *maximum* of those speeds.
pcie_get_supported_speeds() neglects to honor the Max Link Speed field and
will thus incorrectly deem higher speeds as supported. Fix it.
One user-visible issue addressed here is an incorrect value in the sysfs
attribute "max_link_speed".
But the main motivation is a boot hang reported by Niklas: Intel JHL7540
"Titan Ridge 2018" Thunderbolt controllers supports 2.5-8 GT/s speeds,
but indicate 2.5 GT/s as maximum. Ilpo recalls seeing this on more
devices. It can be explained by the controller's Downstream Ports
supporting 8 GT/s if an Endpoint is attached, but limiting to 2.5 GT/s
if the port interfaces to a PCIe Adapter, in accordance with USB4 v2
sec 11.2.1:
"This section defines the functionality of an Internal PCIe Port that
interfaces to a PCIe Adapter. [...]
The Logical sub-block shall update the PCIe configuration registers
with the following characteristics: [...]
Max Link Speed field in the Link Capabilities Register set to 0001b
(data rate of 2.5 GT/s only).
Note: These settings do not represent actual throughput. Throughput
is implementation specific and based on the USB4 Fabric performance."
The present commit is not sufficient on its own to fix Niklas' boot hang,
but it is a prerequisite: A subsequent commit will fix the boot hang by
enabling bandwidth control only if more than one speed is supported.
The GENMASK() macro used herein specifies 0 as lowest bit, even though
the Supported Link Speeds Vector ends at bit 1. This is done on purpose
to avoid a GENMASK(0, 1) macro if Max Link Speed is zero. That macro
would be invalid as the lowest bit is greater than the highest bit.
Ilpo has witnessed a zero Max Link Speed on Root Complex Integrated
Endpoints in particular, so it does occur in practice. (The Link
Capabilities Register is optional on RCiEPs per PCIe r6.2 sec 7.5.3.)
Fixes: d2bd39c045 ("PCI: Store all PCIe Supported Link Speeds")
Closes: https://lore.kernel.org/r/70829798889c6d779ca0f6cd3260a765780d1369.camel@kernel.org
Link: https://lore.kernel.org/r/fe03941e3e1cc42fb9bf4395e302bff53ee2198b.1734428762.git.lukas@wunner.de
Reported-by: Niklas Schnelle <niks@kernel.org>
Tested-by: Niklas Schnelle <niks@kernel.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 675f940576 upstream.
Commit 2df7168717 ("dm: Always split write BIOs to zoned device
limits") updates the device-mapper driver to perform splits for the
write BIOs. However, it did not address the cases where DM targets do
not emulate zone append, such as in the cases of dm-linear or dm-flakey.
For these targets, when the write BIOs span across zone boundaries, they
trigger WARN_ON_ONCE(bio_straddles_zones(bio)) in
blk_zone_wplug_handle_write(). This results in I/O errors. The errors
are reproduced by running blktests test case zbd/004 using zoned
dm-linear or dm-flakey devices.
To avoid the I/O errors, handle the write BIOs regardless whether DM
targets emulate zone append or not, so that all write BIOs are split at
zone boundaries. For that purpose, drop the check for zone append
emulation in dm_zone_bio_needs_split(). Its argument 'md' is no longer
used then drop it also.
Fixes: 2df7168717 ("dm: Always split write BIOs to zoned device limits")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Link: https://lore.kernel.org/r/20250717103539.37279-1-shinichiro.kawasaki@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61399e0c54 upstream.
RCU re-initializes the deferred QS irq work everytime before attempting
to queue it. However there are situations where the irq work is
attempted to be queued even though it is already queued. In that case
re-initializing messes-up with the irq work queue that is about to be
handled.
The chances for that to happen are higher when the architecture doesn't
support self-IPIs and irq work are then all lazy, such as with the
following sequence:
1) rcu_read_unlock() is called when IRQs are disabled and there is a
grace period involving blocked tasks on the node. The irq work
is then initialized and queued.
2) The related tasks are unblocked and the CPU quiescent state
is reported. rdp->defer_qs_iw_pending is reset to DEFER_QS_IDLE,
allowing the irq work to be requeued in the future (note the previous
one hasn't fired yet).
3) A new grace period starts and the node has blocked tasks.
4) rcu_read_unlock() is called when IRQs are disabled again. The irq work
is re-initialized (but it's queued! and its node is cleared) and
requeued. Which means it's requeued to itself.
5) The irq work finally fires with the tick. But since it was requeued
to itself, it loops and hangs.
Fix this with initializing the irq work only once before the CPU boots.
Fixes: b41642c877 ("rcu: Fix rcu_read_unlock() deadloop due to IRQ work")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202508071303.c1134cce-lkp@intel.com
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.upadhyay@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d418e4fd9 upstream.
[Why & How]
Not letting DCN301 to clear after surface/stream update results
in artifacts when switching between active overlay planes. The issue
is known and has been solved initially. See below:
(https://gitlab.freedesktop.org/drm/amd/-/issues/3441)
Fixes: f354556e29 ("drm/amd/display: limit clear_update_flags t dcn32 and above")
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62d6b81e8b upstream.
The old SET_SYSTEM_SLEEP_PM_OPS() macro leads to a warning about an
unused function:
| drivers/firmware/arm_scmi/scmi_power_control.c:363:12: error:
| 'scmi_system_power_resume' defined but not used [-Werror=unused-function]
| static int scmi_system_power_resume(struct device *dev)
The proper way to do this these days is to use SYSTEM_SLEEP_PM_OPS()
and pm_sleep_ptr().
Fixes: 9a0658d399 ("firmware: arm_scmi: power_control: Ensure SCMI_SYSPOWER_IDLE is set early during resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Message-Id: <20250709070107.1388512-1-arnd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 825aea662b upstream.
kernel test robot reports that a recent change of the sqe->rw_flags
field throws a sparse warning on 32-bit archs:
>> io_uring/rw.c:291:19: sparse: sparse: incorrect type in assignment (different base types) @@ expected restricted __kernel_rwf_t [usertype] flags @@ got unsigned int @@
io_uring/rw.c:291:19: sparse: expected restricted __kernel_rwf_t [usertype] flags
io_uring/rw.c:291:19: sparse: got unsigned int
Force cast it to rwf_t to silence that new sparse warning.
Fixes: cf73d9970e ("io_uring: don't use int for ABI")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507032211.PwSNPNSP-lkp@intel.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0060beec0b upstream.
A port link power management (LPM) policy can be controlled using the
link_power_management_policy sysfs host attribute. However, this
attribute exists also for hosts that do not support LPM and in such
case, attempting to change the LPM policy for the host (port) will fail
with -EOPNOTSUPP.
Introduce the new sysfs link_power_management_supported host attribute
to indicate to the user if a the port and the devices connected to the
port for the host support LPM, which implies that the
link_power_management_policy attribute can be used.
Since checking that a port and its devices support LPM is common between
the new ata_scsi_lpm_supported_show() function and the existing
ata_scsi_lpm_store() function, the new helper ata_scsi_lpm_supported()
is introduced.
Fixes: 413e800cad ("ata: libata-sata: Disallow changing LPM state if not supported")
Reported-by: Borah, Chaitanya Kumar <chaitanya.kumar.borah@intel.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202507251014.a5becc3b-lkp@intel.com
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abbf9a4494 upstream.
Starting with Rust 1.88.0 (released 2025-06-26), `rustdoc` complains
about a target modifier mismatch in configurations where `-Zfixed-x18`
is passed:
error: mixing `-Zfixed-x18` will cause an ABI mismatch in crate `rust_out`
|
= help: the `-Zfixed-x18` flag modifies the ABI so Rust crates compiled with different values of this flag cannot be used together safely
= note: unset `-Zfixed-x18` in this crate is incompatible with `-Zfixed-x18=` in dependency `core`
= help: set `-Zfixed-x18=` in this crate or unset `-Zfixed-x18` in `core`
= help: if you are sure this will not cause problems, you may use `-Cunsafe-allow-abi-mismatch=fixed-x18` to silence this error
The reason is that `rustdoc` was not passing the target modifiers when
configuring the session options, and thus it would report a mismatch
that did not exist as soon as a target modifier is used in a dependency.
We did not notice it in the kernel until now because `-Zfixed-x18` has
been a target modifier only since 1.88.0 (and it is the only one we use
so far).
The issue has been reported upstream [1] and a fix has been submitted
[2], including a test similar to the kernel case.
[ This is now fixed upstream (thanks Guillaume for the quick review),
so it will be fixed in Rust 1.90.0 (expected 2025-09-18).
- Miguel ]
Meanwhile, conditionally pass `-Cunsafe-allow-abi-mismatch=fixed-x18`
to workaround the issue on our side.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/rust-for-linux/36cdc798-524f-4910-8b77-d7b9fac08d77@oss.qualcomm.com/
Link: https://github.com/rust-lang/rust/issues/144521 [1]
Link: https://github.com/rust-lang/rust/pull/144523 [2]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250727092317.2930617-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 252fea131e upstream.
`rustdoc` can get confused when generating documentation into a folder
that contains generated files from other `rustdoc` versions.
For instance, running something like:
rustup default 1.78.0
make LLVM=1 rustdoc
rustup default 1.88.0
make LLVM=1 rustdoc
may generate errors like:
error: couldn't generate documentation: invalid template: last line expected to start with a comment
|
= note: failed to create or modify "./Documentation/output/rust/rustdoc/src-files.js"
Thus just always clean the output folder before generating the
documentation -- we are anyway regenerating it every time the `rustdoc`
target gets called, at least for the time being.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Reported-by: Daniel Almeida <daniel.almeida@collabora.com>
Closes: https://rust-for-linux.zulipchat.com/#narrow/channel/288089/topic/x/near/527201113
Reviewed-by: Tamir Duberstein <tamird@kernel.org>
Link: https://lore.kernel.org/r/20250726133435.2460085-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 65ba2a6e77 ]
According to the "GPIO Expander Map / Table" section of the J722S EVM
Schematic within the Evaluation Module Design Files package [0], the
GPIO Pin P05 located on the GPIO Expander 1 (I2C0/0x23) has to be pulled
down to select the Type-C interface. Since commit under Fixes claims to
enable the Type-C interface, update the property within "p05-hog" from
"output-high" to "output-low", thereby switching from the Type-A
interface to the Type-C interface.
[0]: https://www.ti.com/lit/zip/sprr495
Cc: stable@vger.kernel.org
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250623100657.4082031-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc8d9e6b58 ]
J722S SOC has two usb controllers USB0 and USB1. USB0 is brought out on
the EVM as a stacked USB connector which has one Type-A and one Type-C
port. These Type-A and Type-C ports are connected to MUX so only
one of them can be enabled at a time.
Commit under Fixes, tries to enable the USB0 instance of USB to
interface with the Type-C port via the USB hub, by configuring the
USB2.0_MUX_SEL to GPIO_ACTIVE_HIGH. But it is observed on J722S-EVM
that Type-A port is enabled instead of Type-C port.
Fix this by setting USB2.0_MUX_SEL to GPIO_ACTIVE_LOW to enable Type-C
port.
Fixes: 485705df5d ("arm64: dts: ti: k3-j722s: Enable PCIe and USB support on J722S-EVM")
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20250116125726.2549489-1-h-salunke@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 65ba2a6e77 ("arm64: dts: ti: k3-j722s-evm: Fix USB gpio-hog level for Type-C")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cff20ce3b ]
pci_bridge_d3_possible() is called from both pcie_portdrv_probe() and
pcie_portdrv_remove() to determine whether runtime power management shall
be enabled (on probe) or disabled (on remove) on a PCIe port.
The underlying assumption is that pci_bridge_d3_possible() always returns
the same value, else a runtime PM reference imbalance would occur. That
assumption is not given if the PCIe port is inaccessible on remove due to
hot-unplug: pci_bridge_d3_possible() calls pciehp_is_native(), which
accesses Config Space to determine whether the port is Hot-Plug Capable.
An inaccessible port returns "all ones", which is converted to "all
zeroes" by pcie_capability_read_dword(). Hence the port no longer seems
Hot-Plug Capable on remove even though it was on probe.
The resulting runtime PM ref imbalance causes warning messages such as:
pcieport 0000:02:04.0: Runtime PM usage count underflow!
Avoid the Config Space access (and thus the runtime PM ref imbalance) by
caching the Hot-Plug Capable bit in struct pci_dev.
The struct already contains an "is_hotplug_bridge" flag, which however is
not only set on Hot-Plug Capable PCIe ports, but also Conventional PCI
Hot-Plug bridges and ACPI slots. The flag identifies bridges which are
allocated additional MMIO and bus number resources to allow for hierarchy
expansion.
The kernel is somewhat sloppily using "is_hotplug_bridge" in a number of
places to identify Hot-Plug Capable PCIe ports, even though the flag
encompasses other devices. Subsequent commits replace these occurrences
with the new flag to clearly delineate Hot-Plug Capable PCIe ports from
other kinds of hotplug bridges.
Document the existing "is_hotplug_bridge" and the new "is_pciehp" flag
and document the (non-obvious) requirement that pci_bridge_d3_possible()
always returns the same value across the entire lifetime of a bridge,
including its hot-removal.
Fixes: 5352a44a56 ("PCI: pciehp: Make pciehp_is_native() stricter")
Reported-by: Laurent Bigonville <bigon@bigon.be>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220216
Reported-by: Mario Limonciello <mario.limonciello@amd.com>
Closes: https://lore.kernel.org/r/20250609020223.269407-3-superm1@kernel.org/
Link: https://lore.kernel.org/all/20250620025535.3425049-3-superm1@kernel.org/T/#u
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://patch.msgid.link/fe5dcc3b2e62ee1df7905d746bde161eb1b3291c.1752390101.git.lukas@wunner.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5fb3ff632 ]
Currently, pci_bridge_d3_possible() encodes a variety of decision factors
when deciding whether a given bridge can be put into D3. A particular one
of note is for "recent enough PCIe ports." Per Rafael [0]:
"There were hardware issues related to PM on x86 platforms predating
the introduction of Connected Standby in Windows. For instance,
programming a port into D3hot by writing to its PMCSR might cause the
PCIe link behind it to go down and the only way to revive it was to
power cycle the Root Complex. And similar."
Thus, this function contains a DMI-based check for post-2015 BIOS.
The above factors (Windows, x86) don't really apply to non-x86 systems, and
also, many such systems don't have BIOS or DMI. However, we'd like to be
able to suspend bridges on non-x86 systems too.
Restrict the "recent enough" check to x86. If we find further
incompatibilities, it probably makes sense to expand on the deny-list
approach (i.e., bridge_d3_blacklist or similar).
Link: https://lore.kernel.org/r/20250320110604.v6.1.Id0a0e78ab0421b6bce51c4b0b87e6aebdfc69ec7@changeid
Link: https://lore.kernel.org/linux-pci/CAJZ5v0j_6jeMAQ7eFkZBe5Yi+USGzysxAgfemYh=-zq4h5W+Qg@mail.gmail.com/ [0]
Link: https://lore.kernel.org/linux-pci/20240227225442.GA249898@bhelgaas/ [1]
Link: https://lore.kernel.org/linux-pci/20240828210705.GA37859@bhelgaas/ [2]
[Brian: rewrite to !X86 based on Rafael's suggestions]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Stable-dep-of: 6cff20ce3b ("PCI/ACPI: Fix runtime PM ref imbalance on Hot-Plug Capable ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2bd39c045 ]
The PCIe bandwidth controller added by a subsequent commit will require
selecting PCIe Link Speeds that are lower than the Maximum Link Speed.
The struct pci_bus only stores max_bus_speed. Even if PCIe r6.1 sec 8.2.1
currently disallows gaps in supported Link Speeds, the Implementation Note
in PCIe r6.1 sec 7.5.3.18, recommends determining supported Link Speeds
using the Supported Link Speeds Vector in the Link Capabilities 2 Register
(when available) to "avoid software being confused if a future
specification defines Links that do not require support for all slower
speeds."
Reuse code in pcie_get_speed_cap() to add pcie_get_supported_speeds() to
query the Supported Link Speeds Vector of a PCIe device. The value is taken
directly from the Supported Link Speeds Vector or synthesized from the Max
Link Speed in the Link Capabilities Register when the Link Capabilities 2
Register is not available.
The Supported Link Speeds Vector in the Link Capabilities Register 2
corresponds to the bus below on Root Ports and Downstream Ports, whereas it
corresponds to the bus above on Upstream Ports and Endpoints (PCIe r6.1 sec
7.5.3.18):
Supported Link Speeds Vector - This field indicates the supported Link
speed(s) of the associated Port.
Add supported_speeds into the struct pci_dev that caches the
Supported Link Speeds Vector.
supported_speeds contains a set of Link Speeds only in the case where PCIe
Link Speed can be determined. Root Complex Integrated Endpoints do not have
a well-defined Link Speed because they do not implement either of the Link
Capabilities Registers, which is allowed by PCIe r6.1 sec 7.5.3 (the same
limitation applies to determining cur_bus_speed and max_bus_speed that are
PCI_SPEED_UNKNOWN in such case). This is of no concern from PCIe bandwidth
controller point of view because such devices are not attached into a PCIe
Root Port that could be controlled.
The supported_speeds field keeps the extra reserved zero at the least
significant bit to match the Link Capabilities 2 Register layout.
An attempt was made to store supported_speeds field into the struct pci_bus
as an intersection of both ends of the Link, however, the subordinate
struct pci_bus is not available early enough. The Target Speed quirk (in
pcie_failed_link_retrain()) can run either during initial scan or later,
requiring it to use the API provided by the PCIe bandwidth controller to
set the Target Link Speed in order to co-exist with the bandwidth
controller. When the Target Speed quirk is calling the bandwidth controller
during initial scan, the struct pci_bus is not yet initialized. As such,
storing supported_speeds into the struct pci_bus is not viable.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20241018144755.7875-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: move pcie_get_supported_speeds() decl to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 6cff20ce3b ("PCI/ACPI: Fix runtime PM ref imbalance on Hot-Plug Capable ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 59b33fab4c ]
After commit 5c70eb5c59 ("net: better track kernel sockets lifetime"),
kernel sockets now use net_passive reference counting. However, commit
95d2b9f693 ("Revert "smb: client: fix TCP timers deadlock after rmmod"")
restored the manual socket refcount manipulation without adapting to this
new mechanism, causing a memory leak.
The issue can be reproduced by[1]:
1. Creating a network namespace
2. Mounting and Unmounting CIFS within the namespace
3. Deleting the namespace
Some memory leaks may appear after a period of time following step 3.
unreferenced object 0xffff9951419f6b00 (size 256):
comm "ip", pid 447, jiffies 4294692389 (age 14.730s)
hex dump (first 32 bytes):
1b 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 80 77 c2 44 51 99 ff ff .........w.DQ...
backtrace:
__kmem_cache_alloc_node+0x30e/0x3d0
__kmalloc+0x52/0x120
net_alloc_generic+0x1d/0x30
copy_net_ns+0x86/0x200
create_new_namespaces+0x117/0x300
unshare_nsproxy_namespaces+0x60/0xa0
ksys_unshare+0x148/0x360
__x64_sys_unshare+0x12/0x20
do_syscall_64+0x59/0x110
entry_SYSCALL_64_after_hwframe+0x78/0xe2
...
unreferenced object 0xffff9951442e7500 (size 32):
comm "mount.cifs", pid 475, jiffies 4294693782 (age 13.343s)
hex dump (first 32 bytes):
40 c5 38 46 51 99 ff ff 18 01 96 42 51 99 ff ff @.8FQ......BQ...
01 00 00 00 6f 00 c5 07 6f 00 d8 07 00 00 00 00 ....o...o.......
backtrace:
__kmem_cache_alloc_node+0x30e/0x3d0
kmalloc_trace+0x2a/0x90
ref_tracker_alloc+0x8e/0x1d0
sk_alloc+0x18c/0x1c0
inet_create+0xf1/0x370
__sock_create+0xd7/0x1e0
generic_ip_connect+0x1d4/0x5a0 [cifs]
cifs_get_tcp_session+0x5d0/0x8a0 [cifs]
cifs_mount_get_session+0x47/0x1b0 [cifs]
dfs_mount_share+0xfa/0xa10 [cifs]
cifs_mount+0x68/0x2b0 [cifs]
cifs_smb3_do_mount+0x10b/0x760 [cifs]
smb3_get_tree+0x112/0x2e0 [cifs]
vfs_get_tree+0x29/0xf0
path_mount+0x2d4/0xa00
__se_sys_mount+0x165/0x1d0
Root cause:
When creating kernel sockets, sk_alloc() calls net_passive_inc() for
sockets with sk_net_refcnt=0. The CIFS code manually converts kernel
sockets to user sockets by setting sk_net_refcnt=1, but doesn't call
the corresponding net_passive_dec(). This creates an imbalance in the
net_passive counter, which prevents the network namespace from being
destroyed when its last user reference is dropped. As a result, the
entire namespace and all its associated resources remain allocated.
Timeline of patches leading to this issue:
- commit ef7134c7fc ("smb: client: Fix use-after-free of network
namespace.") in v6.12 fixed the original netns UAF by manually
managing socket refcounts
- commit e9f2517a3e ("smb: client: fix TCP timers deadlock after
rmmod") in v6.13 attempted to use kernel sockets but introduced
TCP timer issues
- commit 5c70eb5c59 ("net: better track kernel sockets lifetime")
in v6.14-rc5 introduced the net_passive mechanism with
sk_net_refcnt_upgrade() for proper socket conversion
- commit 95d2b9f693 ("Revert "smb: client: fix TCP timers deadlock
after rmmod"") in v6.15-rc3 reverted to manual refcount management
without adapting to the new net_passive changes
Fix this by using sk_net_refcnt_upgrade() which properly handles the
net_passive counter when converting kernel sockets to user sockets.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220343 [1]
Fixes: 95d2b9f693 ("Revert "smb: client: fix TCP timers deadlock after rmmod"")
Cc: stable@vger.kernel.org
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Wang Zhaolong <wangzhaolong@huaweicloud.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e57a632021 ]
net_drop_ns() is NULL when CONFIG_NET_NS is disabled.
The next patch introduces a function that increments
and decrements net->passive.
As a prep, let's rename and export net_free() to
net_passive_dec() and add net_passive_inc().
Suggested-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/netdev/CANn89i+oUCt2VGvrbrweniTendZFEh+nwS=uonc004-aPkWy-Q@mail.gmail.com/
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250217191129.19967-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 59b33fab4c ("smb: client: fix netns refcount leak after net_passive changes")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e40fc1160d upstream.
The charge-control subsystem in the ChromeOS EC is not strictly tied to
its USB-PD subsystem.
Since commit 7613bc0d11 ("mfd: cros_ec: Don't load charger with UCSI")
the presence of EC_FEATURE_UCSI_PPM would inhibit the probing of the
charge-control driver.
Furthermore recent versions of the EC firmware in Framework laptops
hard-disable EC_FEATURE_USB_PD to avoid probing cros-usbpd-charger,
which then also breaks cros-charge-control.
Instead use the dedicated EC_FEATURE_CHARGER.
Cc: stable@vger.kernel.org
Link: 1d7bcf1d50
Fixes: 555b5fcdb8 ("mfd: cros_ec: Register charge control subdevice")
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Tested-by: Tom Vincent <linux@tlvince.com>
Link: https://lore.kernel.org/r/20250521-cros-ec-mfd-chctl-probe-v1-1-6ebfe3a6efa7@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c061046fe9 upstream.
Currently, the battery timer is set up for all devices using hid-apple,
irrespective of whether they actually have a battery or not.
APPLE_RDESC_BATTERY is a quirk that indicates the device has a battery
and needs the battery timer. This patch checks for this quirk before
setting up the timer, ensuring that only devices with a battery will
have the timer set up.
Fixes: 6e143293e1 ("HID: apple: Report Magic Keyboard battery over USB")
Cc: stable@vger.kernel.org
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4131a50d0 upstream.
Size of ring buffer, as defined in uio_hv_generic driver, is no longer
fixed to 16 KB. This creates a problem in fcopy, since this size was
hardcoded. With the change in place to make ring sysfs node actually
reflect the size of underlying ring buffer, it is safe to get the size
of ring sysfs file and use it for ring buffer size in fcopy daemon.
Fix the issue of disparity in ring buffer size, by making it dynamic
in fcopy uio daemon.
Cc: stable@vger.kernel.org
Fixes: 0315fef2af ("uio_hv_generic: Align ring size to system page")
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Link: https://lore.kernel.org/r/20250711060846.9168-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250711060846.9168-1-namjain@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16ee3ea8fa upstream.
When userspace sets supported rates for a new station via
NL80211_CMD_NEW_STATION, it might send a list that's empty
or contains only invalid values. Currently, we process these
values in sta_link_apply_parameters() without checking the result of
ieee80211_parse_bitrates(), which can lead to an empty rates bitmap.
A similar issue was addressed for NL80211_CMD_SET_BSS in commit
ce04abc3fc ("wifi: mac80211: check basic rates validity").
This patch applies the same approach in sta_link_apply_parameters()
for NL80211_CMD_NEW_STATION, ensuring there is at least one valid
rate by inspecting the result of ieee80211_parse_bitrates().
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: b95eb7f0ee ("wifi: cfg80211/mac80211: separate link params from station params")
Signed-off-by: Mikhail Lobanov <m.lobanov@rosa.ru>
Link: https://patch.msgid.link/20250317103139.17625-1-m.lobanov@rosa.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Hanne-Lotta Mäenpää <hannelotta@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bdc30e35c upstream.
Currently, the battery timer is set up for all devices using
hid-magicmouse, irrespective of whether they actually need it or not.
The current implementation requires the battery timer for Magic Mouse 2
and Magic Trackpad 2 when connected via USB only. Add checks to ensure
that the battery timer is only set up when they are connected via USB.
Fixes: 0b91b4e4da ("HID: magicmouse: Report battery level over USB")
Cc: stable@vger.kernel.org
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c18646248f upstream.
Ever since commit c2ff29e99a ("siw: Inline do_tcp_sendpages()"),
we have been doing this:
static int siw_tcp_sendpages(struct socket *s, struct page **page, int offset,
size_t size)
[...]
/* Calculate the number of bytes we need to push, for this page
* specifically */
size_t bytes = min_t(size_t, PAGE_SIZE - offset, size);
/* If we can't splice it, then copy it in, as normal */
if (!sendpage_ok(page[i]))
msg.msg_flags &= ~MSG_SPLICE_PAGES;
/* Set the bvec pointing to the page, with len $bytes */
bvec_set_page(&bvec, page[i], bytes, offset);
/* Set the iter to $size, aka the size of the whole sendpages (!!!) */
iov_iter_bvec(&msg.msg_iter, ITER_SOURCE, &bvec, 1, size);
try_page_again:
lock_sock(sk);
/* Sendmsg with $size size (!!!) */
rv = tcp_sendmsg_locked(sk, &msg, size);
This means we've been sending oversized iov_iters and tcp_sendmsg calls
for a while. This has a been a benign bug because sendpage_ok() always
returned true. With the recent slab allocator changes being slowly
introduced into next (that disallow sendpage on large kmalloc
allocations), we have recently hit out-of-bounds crashes, due to slight
differences in iov_iter behavior between the MSG_SPLICE_PAGES and
"regular" copy paths:
(MSG_SPLICE_PAGES)
skb_splice_from_iter
iov_iter_extract_pages
iov_iter_extract_bvec_pages
uses i->nr_segs to correctly stop in its tracks before OoB'ing everywhere
skb_splice_from_iter gets a "short" read
(!MSG_SPLICE_PAGES)
skb_copy_to_page_nocache copy=iov_iter_count
[...]
copy_from_iter
/* this doesn't help */
if (unlikely(iter->count < len))
len = iter->count;
iterate_bvec
... and we run off the bvecs
Fix this by properly setting the iov_iter's byte count, plus sending the
correct byte count to tcp_sendmsg_locked.
Link: https://patch.msgid.link/r/20250729120348.495568-1-pfalcato@suse.de
Cc: stable@vger.kernel.org
Fixes: c2ff29e99a ("siw: Inline do_tcp_sendpages()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202507220801.50a7210-lkp@intel.com
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Pedro Falcato <pfalcato@suse.de>
Acked-by: Bernard Metzler <bernard.metzler@linux.dev>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
