There is a spelling mistake in the Kconfig text. Fix it.
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Allow to extend expression of sub nodes to optionally indicate bit
position. This extension is needed to distinguish between different bit
positions in the same address.
For example, there are two nvmem nodes starting with bit 4 and bit 0
at the same address 0x54. In this case, it can be expressed as follows.
trim@54,4 {
reg = <0x54 1>;
bits = <4 2>;
};
trim@54,0 {
reg = <0x54 1>;
bits = <0 4>;
};
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1626661864-15473-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Rob Herring <robh@kernel.org>
There's an undocumented dependency between LCD layer enable bits [2-5]
and the AXI pipelined read enable bit [28] in the LCD_CONTROL register.
The proper order of operation is:
1) Clear AXI pipelined read enable bit
2) Set LCD layers
3) Set AXI pipelined read enable bit
With this update, LCD can start DMA when TVDDCV is reduced down to 700mV.
Fixes: 7f7b96a8a0 ("drm/kmb: Add support for KeemBay Display")
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728003126.1425028-1-anitha.chrisanthus@intel.com
Fix the following fallthrough warning (on ARM):
drivers/scsi/arm/fas216.c:1379:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
default:
^
drivers/scsi/arm/fas216.c:1379:2: note: insert 'break;' to avoid fall-through
default:
^
break;
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202107260355.bF00i5bi-lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Fix the following fallthrough warning (on ARM):
drivers/scsi/arm/acornscsi.c:2651:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case res_success:
^
drivers/scsi/arm/acornscsi.c:2651:2: note: insert '__attribute__((fallthrough));' to silence this warning
case res_success:
^
__attribute__((fallthrough));
drivers/scsi/arm/acornscsi.c:2651:2: note: insert 'break;' to avoid fall-through
case res_success:
^
break;
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202107260355.bF00i5bi-lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
An I2S frame always has a left and right channel slot even if mono
data is being sent. So if channels==1 the actual bitclock frequency
is 2 * snd_soc_params_to_bclk(params).
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2cdba9b045 ("ASoC: cs42l42: Use bclk from hw_params if set_sysclk was not called")
Link: https://lore.kernel.org/r/20210729170929.6589-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has no support for left-justified protocol so it should
not have been allowing this to be passed to cs42l42_set_dai_fmt().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210729170929.6589-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC volume is a signed 8-bit number with range -97 to +12,
with -97 being mute. Use a SOC_SINGLE_S8_TLV() to define this
and fix the DECLARE_TLV_DB_SCALE() to have the correct start and
mute flag.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210729170929.6589-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gpiolib core code has been updated to support setting friendly names
through properly 'gpio-line-names'. Instead of redefine behaviour here
to skip the core to be executed, just properly assign the desired offset
per bank to get in the core the expected behaviour.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This driver uses multiple gpiochip banks per device. To support
'gpio-line-names' along the banks 'offset' for each bank must be
set explicitly.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The default gpiolib-of implementation does not work with the multiple
gpiochip banks per device structure used for example by the gpio-mt7621
and gpio-brcmstb drivers. To fix these kind of situations driver code
is forced to fill the names to avoid the gpiolib code to set names
repeated along the banks. Instead of continue with that antipattern
fix the gpiolib core function to get expected behaviour for every
single situation adding a field 'offset' in the gpiochip structure.
Doing in this way, we can assume this offset will be zero for normal
driver code where only one gpiochip bank per device is used but
can be set explicitly in those drivers that really need more than
one gpiochip.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In error handling branch "if (WARN_ON(node == NUMA_NO_NODE))", the
previously allocated memories are not released. Doing this before
allocating memory eliminates memory leaks.
tj: Note that the condition only occurs when the arch code is pretty broken
and the WARN_ON might as well be BUG_ON().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
CNL is the only platform with GRAPHICS_VER == 10. With its removal we
don't need to handle that version anymore.
Also we can now reduce the max number of slices: the call to
intel_sseu_set_info() with the highest number of slices comes from SKL
and BDW with 3 slices. Recent platforms actually increase the
number of subslices so the number of slices remain 1.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-3-lucas.demarchi@intel.com
Source needs to write DPCD 103-106 after receiving a PHY request to change
swing/pre-emphasis after reading DPCD 206-207. This is especially needed if
there is a retimer between source and sink and the retimer implements AUX_CH
interception scheme to manage DP PHY settings (e.g. adjusting Swing/Pre-emphasis
equalization level) for DP output channel. If the source doesn't write to
DPCD 103-106, the retimer may not output the requested swing/pre-emphasis and
eventually we fail compliance.
v2: Rebase and use crtc->lane_count (Imre)
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226081554.984307-1-khaled.almahallawy@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
- Fix MTE shared page detection
- Enable selftest's use of PMU registers when asked to
s390:
- restore 5.13 debugfs names
x86:
- fix sizes for vcpu-id indexed arrays
- fixes for AMD virtualized LAPIC (AVIC)
- other small bugfixes
Generic:
- access tracking performance test
- dirty_log_perf_test command line parsing fix
- Fix selftest use of obsolete pthread_yield() in favour of sched_yield()
- use cpu_relax when halt polling
- fixed missing KVM_CLEAR_DIRTY_LOG compat ioctl
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmECvOwUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMjuAf/ZdJx7RKRQxMHG4jHGDtOIQq3qxds
2uJsFZS3MWkphSOJ+mbomdXTOCHvhPbJlr5TXaSxGnasmAAl+mDk2qVT0tH6638m
r6M+fu4X0RYvFz54Qnf96V0/elE6ee8rtteXD8WVKQ/XzE3odk1EOqbe7CBDx7yo
A3SzO8eSBzxamKo22fmE3MR5LVVAcN9wNsCb88XGDTUkTbYl+w597r6zg83rMMlL
gwD4f9+NYX6h88BVVwLUkWotUrD/5rRGpRVVEZk5eZKvFGzpukk15dfv0PA9347O
AOM0i/PgnA+Qw6ZsTetWPjD8eFcXDBurGF1tIkyo4X8VogQG0wFIHxbezQ==
=ZgK/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix MTE shared page detection
- Enable selftest's use of PMU registers when asked to
s390:
- restore 5.13 debugfs names
x86:
- fix sizes for vcpu-id indexed arrays
- fixes for AMD virtualized LAPIC (AVIC)
- other small bugfixes
Generic:
- access tracking performance test
- dirty_log_perf_test command line parsing fix
- Fix selftest use of obsolete pthread_yield() in favour of
sched_yield()
- use cpu_relax when halt polling
- fixed missing KVM_CLEAR_DIRTY_LOG compat ioctl"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add missing compat KVM_CLEAR_DIRTY_LOG
KVM: use cpu_relax when halt polling
KVM: SVM: use vmcb01 in svm_refresh_apicv_exec_ctrl
KVM: SVM: tweak warning about enabled AVIC on nested entry
KVM: SVM: svm_set_vintr don't warn if AVIC is active but is about to be deactivated
KVM: s390: restore old debugfs names
KVM: SVM: delay svm_vcpu_init_msrpm after svm->vmcb is initialized
KVM: selftests: Introduce access_tracking_perf_test
KVM: selftests: Fix missing break in dirty_log_perf_test arg parsing
x86/kvm: fix vcpu-id indexed array sizes
KVM: x86: Check the right feature bit for MSR_KVM_ASYNC_PF_ACK access
docs: virt: kvm: api.rst: replace some characters
KVM: Documentation: Fix KVM_CAP_ENFORCE_PV_FEATURE_CPUID name
KVM: nSVM: Swap the parameter order for svm_copy_vmrun_state()/svm_copy_vmloadsave_state()
KVM: nSVM: Rename nested_svm_vmloadsave() to svm_copy_vmloadsave_state()
KVM: arm64: selftests: get-reg-list: actually enable pmu regs in pmu sublist
KVM: selftests: change pthread_yield to sched_yield
KVM: arm64: Fix detection of shared VMAs on guest fault
When enabling KVM_CAP_ARM_MTE the ioctl checks that there are no VCPUs
created to ensure that the capability is enabled before the VM is
running. However no locks are held at that point so it is
(theoretically) possible for another thread in the VMM to create VCPUs
between the check and actually setting mte_enabled. Close the race by
taking kvm->lock.
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Fixes: 673638f434 ("KVM: arm64: Expose KVM_ARM_CAP_MTE")
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210729160036.20433-1-steven.price@arm.com
Hyp checks whether an address range only covers RAM by checking the
start/endpoints against a list of memblock_region structs. However,
the endpoint here is exclusive but internally is treated as inclusive.
Fix the off-by-one error that caused valid address ranges to be
rejected.
Cc: Quentin Perret <qperret@google.com>
Fixes: 90134ac9ca ("KVM: arm64: Protect the .hyp sections from the host")
Signed-off-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210728153232.1018911-2-dbrazdil@google.com
In verify_mpllb_state() encoder is retrieved from best_encoder
of connector_state. As there will be only one connector_state
for bigjoiner and checking encoder may not be needed for
bigjoiner-slave. This code path related to mpll is done on dg2
and need this fix to avoid null pointer dereference issue.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-30-matthew.d.roper@intel.com
The PSR enable/disable sequences now require that we program an extra
register in the PHY to adjust the lane disable power setting.
Bspec: 49274
Bspec: 53885
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-29-matthew.d.roper@intel.com
Initialization of the PHY is handled by the hardware/firmware, but the
driver should wait up to 25ms for the PHY to report that its calibration
has completed.
Bspec: 49189
Bspec: 50107
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-28-matthew.d.roper@intel.com
Pull m68knommu fix from Greg Ungerer:
"A single compile time fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k/coldfire: change pll var. to clk_pll
While reviewing the buffer item recovery code, the thought occurred to
me: in V5 filesystems we use log sequence number (LSN) tracking to avoid
replaying older metadata updates against newer log items. However, we
use the magic number of the ondisk buffer to find the LSN of the ondisk
metadata, which means that if an attacker can control the layout of the
realtime device precisely enough that the start of an rt bitmap block
matches the magic and UUID of some other kind of block, they can control
the purported LSN of that spoofed block and thereby break log replay.
Since realtime bitmap and summary blocks don't have headers at all, we
have no way to tell if a block really should be replayed. The best we
can do is replay unconditionally and hope for the best.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
From the department of "generic/482 keeps on giving", we bring you
another tail update race condition:
iclog:
S1 C1
+-----------------------+-----------------------+
S2 EOIC
Two checkpoints in a single iclog. One is complete, the other just
contains the start record and overruns into a new iclog.
Timeline:
Before S1: Cache flush, log tail = X
At S1: Metadata stable, write start record and checkpoint
At C1: Write commit record, set NEED_FUA
Single iclog checkpoint, so no need for NEED_FLUSH
Log tail still = X, so no need for NEED_FLUSH
After C1,
Before S2: Cache flush, log tail = X
At S2: Metadata stable, write start record and checkpoint
After S2: Log tail moves to X+1
At EOIC: End of iclog, more journal data to write
Releases iclog
Not a commit iclog, so no need for NEED_FLUSH
Writes log tail X+1 into iclog.
At this point, the iclog has tail X+1 and NEED_FUA set. There has
been no cache flush for the metadata between X and X+1, and the
iclog writes the new tail permanently to the log. THis is sufficient
to violate on disk metadata/journal ordering.
We have two options here. The first is to detect this case in some
manner and ensure that the partial checkpoint write sets NEED_FLUSH
when the iclog is already marked NEED_FUA and the log tail changes.
This seems somewhat fragile and quite complex to get right, and it
doesn't actually make it obvious what underlying problem it is
actually addressing from reading the code.
The second option seems much cleaner to me, because it is derived
directly from the requirements of the C1 commit record in the iclog.
That is, when we write this commit record to the iclog, we've
guaranteed that the metadata/data ordering is correct for tail
update purposes. Hence if we only write the log tail into the iclog
for the *first* commit record rather than the log tail at the last
release, we guarantee that the log tail does not move past where the
the first commit record in the log expects it to be.
IOWs, taking the first option means that replay of C1 becomes
dependent on future operations doing the right thing, not just the
C1 checkpoint itself doing the right thing. This makes log recovery
almost impossible to reason about because now we have to take into
account what might or might not have happened in the future when
looking at checkpoints in the log rather than just having to
reconstruct the past...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Because I cannot tell if the NEED_FLUSH flag is being set correctly
by the log force and CIL push machinery without it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
From the department of "WTAF? How did we miss that!?"...
When we are recovering a buffer, the first thing we do is check the
buffer magic number and extract the LSN from the buffer. If the LSN
is older than the current LSN, we replay the modification to it. If
the metadata on disk is newer than the transaction in the log, we
skip it. This is a fundamental v5 filesystem metadata recovery
behaviour.
generic/482 failed with an attribute writeback failure during log
recovery. The write verifier caught the corruption before it got
written to disk, and the attr buffer dump looked like:
XFS (dm-3): Metadata corruption detected at xfs_attr3_leaf_verify+0x275/0x2e0, xfs_attr3_leaf block 0x19be8
XFS (dm-3): Unmount and run xfs_repair
XFS (dm-3): First 128 bytes of corrupted metadata buffer:
00000000: 00 00 00 00 00 00 00 00 3b ee 00 00 4d 2a 01 e1 ........;...M*..
00000010: 00 00 00 00 00 01 9b e8 00 00 00 01 00 00 05 38 ...............8
^^^^^^^^^^^^^^^^^^^^^^^
00000020: df 39 5e 51 58 ac 44 b6 8d c5 e7 10 44 09 bc 17 .9^QX.D.....D...
00000030: 00 00 00 00 00 02 00 83 00 03 00 cc 0f 24 01 00 .............$..
00000040: 00 68 0e bc 0f c8 00 10 00 00 00 00 00 00 00 00 .h..............
00000050: 00 00 3c 31 0f 24 01 00 00 00 3c 32 0f 88 01 00 ..<1.$....<2....
00000060: 00 00 3c 33 0f d8 01 00 00 00 00 00 00 00 00 00 ..<3............
00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
.....
The highlighted bytes are the LSN that was replayed into the
buffer: 0x100000538. This is cycle 1, block 0x538. Prior to replay,
that block on disk looks like this:
$ sudo xfs_db -c "fsb 0x417d" -c "type attr3" -c p /dev/mapper/thin-vol
hdr.info.hdr.forw = 0
hdr.info.hdr.back = 0
hdr.info.hdr.magic = 0x3bee
hdr.info.crc = 0xb5af0bc6 (correct)
hdr.info.bno = 105448
hdr.info.lsn = 0x100000900
^^^^^^^^^^^
hdr.info.uuid = df395e51-58ac-44b6-8dc5-e7104409bc17
hdr.info.owner = 131203
hdr.count = 2
hdr.usedbytes = 120
hdr.firstused = 3796
hdr.holes = 1
hdr.freemap[0-2] = [base,size]
Note the LSN stamped into the buffer on disk: 1/0x900. The version
on disk is much newer than the log transaction that was being
replayed. That's a bug, and should -never- happen.
So I immediately went to look at xlog_recover_get_buf_lsn() to check
that we handled the LSN correctly. I was wondering if there was a
similar "two commits with the same start LSN skips the second
replay" problem with buffers. I didn't get that far, because I found
a much more basic, rudimentary bug: xlog_recover_get_buf_lsn()
doesn't recognise buffers with XFS_ATTR3_LEAF_MAGIC set in them!!!
IOWs, attr3 leaf buffers fall through the magic number checks
unrecognised, so trigger the "recover immediately" behaviour instead
of undergoing an LSN check. IOWs, we incorrectly replay ATTR3 leaf
buffers and that causes silent on disk corruption of inode attribute
forks and potentially other things....
Git history shows this is *another* zero day bug, this time
introduced in commit 50d5c8d8e9 ("xfs: check LSN ordering for v5
superblocks during recovery") which failed to handle the attr3 leaf
buffers in recovery. And we've failed to handle them ever since...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
When we log an inode, we format the "log inode" core and set an LSN
in that inode core. We do that via xfs_inode_item_format_core(),
which calls:
xfs_inode_to_log_dinode(ip, dic, ip->i_itemp->ili_item.li_lsn);
to format the log inode. It writes the LSN from the inode item into
the log inode, and if recovery decides the inode item needs to be
replayed, it recovers the log inode LSN field and writes it into the
on disk inode LSN field.
Now this might seem like a reasonable thing to do, but it is wrong
on multiple levels. Firstly, if the item is not yet in the AIL,
item->li_lsn is zero. i.e. the first time the inode it is logged and
formatted, the LSN we write into the log inode will be zero. If we
only log it once, recovery will run and can write this zero LSN into
the inode.
This means that the next time the inode is logged and log recovery
runs, it will *always* replay changes to the inode regardless of
whether the inode is newer on disk than the version in the log and
that violates the entire purpose of recording the LSN in the inode
at writeback time (i.e. to stop it going backwards in time on disk
during recovery).
Secondly, if we commit the CIL to the journal so the inode item
moves to the AIL, and then relog the inode, the LSN that gets
stamped into the log inode will be the LSN of the inode's current
location in the AIL, not it's age on disk. And it's not the LSN that
will be associated with the current change. That means when log
recovery replays this inode item, the LSN that ends up on disk is
the LSN for the previous changes in the log, not the current
changes being replayed. IOWs, after recovery the LSN on disk is not
in sync with the LSN of the modifications that were replayed into
the inode. This, again, violates the recovery ordering semantics
that on-disk writeback LSNs provide.
Hence the inode LSN in the log dinode is -always- invalid.
Thirdly, recovery actually has the LSN of the log transaction it is
replaying right at hand - it uses it to determine if it should
replay the inode by comparing it to the on-disk inode's LSN. But it
doesn't use that LSN to stamp the LSN into the inode which will be
written back when the transaction is fully replayed. It uses the one
in the log dinode, which we know is always going to be incorrect.
Looking back at the change history, the inode logging was broken by
commit 93f958f9c4 ("xfs: cull unnecessary icdinode fields") way
back in 2016 by a stupid idiot who thought he knew how this code
worked. i.e. me. That commit replaced an in memory di_lsn field that
was updated only at inode writeback time from the inode item.li_lsn
value - and hence always contained the same LSN that appeared in the
on-disk inode - with a read of the inode item LSN at inode format
time. CLearly these are not the same thing.
Before 93f958f9c4, the log recovery behaviour was irrelevant,
because the LSN in the log inode always matched the on-disk LSN at
the time the inode was logged, hence recovery of the transaction
would never make the on-disk LSN in the inode go backwards or get
out of sync.
A symptom of the problem is this, caught from a failure of
generic/482. Before log recovery, the inode has been allocated but
never used:
xfs_db> inode 393388
xfs_db> p
core.magic = 0x494e
core.mode = 0
....
v3.crc = 0x99126961 (correct)
v3.change_count = 0
v3.lsn = 0
v3.flags2 = 0
v3.cowextsize = 0
v3.crtime.sec = Thu Jan 1 10:00:00 1970
v3.crtime.nsec = 0
After log recovery:
xfs_db> p
core.magic = 0x494e
core.mode = 020444
....
v3.crc = 0x23e68f23 (correct)
v3.change_count = 2
v3.lsn = 0
v3.flags2 = 0
v3.cowextsize = 0
v3.crtime.sec = Thu Jul 22 17:03:03 2021
v3.crtime.nsec = 751000000
...
You can see that the LSN of the on-disk inode is 0, even though it
clearly has been written to disk. I point out this inode, because
the generic/482 failure occurred because several adjacent inodes in
this specific inode cluster were not replayed correctly and still
appeared to be zero on disk when all the other metadata (inobt,
finobt, directories, etc) indicated they should be allocated and
written back.
The fix for this is two-fold. The first is that we need to either
revert the LSN changes in 93f958f9c4 or stop logging the inode LSN
altogether. If we do the former, log recovery does not need to
change but we add 8 bytes of memory per inode to store what is
largely a write-only inode field. If we do the latter, log recovery
needs to stamp the on-disk inode in the same manner that inode
writeback does.
I prefer the latter, because we shouldn't really be trying to log
and replay changes to the on disk LSN as the on-disk value is the
canonical source of the on-disk version of the inode. It also
matches the way we recover buffer items - we create a buf_log_item
that carries the current recovery transaction LSN that gets stamped
into the buffer by the write verifier when it gets written back
when the transaction is fully recovered.
However, this might break log recovery on older kernels even more,
so I'm going to simply ignore the logged value in recovery and stamp
the on-disk inode with the LSN of the transaction being recovered
that will trigger writeback on transaction recovery completion. This
will ensure that the on-disk inode LSN always reflects the LSN of
the last change that was written to disk, regardless of whether it
comes from log recovery or runtime writeback.
Fixes: 93f958f9c4 ("xfs: cull unnecessary icdinode fields")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Before waiting on a iclog in xfs_log_force_lsn(), we don't check to
see if the iclog has already been completed and the contents on
stable storage. We check for completed iclogs in xfs_log_force(), so
we should do the same thing for xfs_log_force_lsn().
This fixed some random up-to-30s pauses seen in unmounting
filesystems in some tests. A log force ends up waiting on completed
iclog, and that doesn't then get flushed (and hence the log force
get completed) until the background log worker issues a log force
that flushes the iclog in question. Then the unmount unblocks and
continues.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
After fixing the tail_lsn vs cache flush race, generic/482 continued
to fail in a similar way where cache flushes were missing before
iclog FUA writes. Tracing of iclog state changes during the fsstress
workload portion of the test (via xlog_iclog* events) indicated that
iclog writes were coming from two sources - CIL pushes and log
forces (due to fsync/O_SYNC operations). All of the cases where a
recovery problem was triggered indicated that the log force was the
source of the iclog write that was not preceeded by a cache flush.
This was an oversight in the modifications made in commit
eef983ffea ("xfs: journal IO cache flush reductions"). Log forces
for fsync imply a data device cache flush has been issued if an
iclog was flushed to disk and is indicated to the caller via the
log_flushed parameter so they can elide the device cache flush if
the journal issued one.
The change in eef983ffea results in iclogs only issuing a cache
flush if XLOG_ICL_NEED_FLUSH is set on the iclog, but this was not
added to the iclogs that the log force code flushes to disk. Hence
log forces are no longer guaranteeing that a cache flush is issued,
hence opening up a potential on-disk ordering failure.
Log forces should also set XLOG_ICL_NEED_FUA as well to ensure that
the actual iclogs it forces to the journal are also on stable
storage before it returns to the caller.
This patch introduces the xlog_force_iclog() helper function to
encapsulate the process of taking a reference to an iclog, switching
its state if WANT_SYNC and flushing it to stable storage correctly.
Both xfs_log_force() and xfs_log_force_lsn() are converted to use
it, as is xlog_unmount_write() which has an elaborate method of
doing exactly the same "write this iclog to stable storage"
operation.
Further, if the log force code needs to wait on a iclog in the
WANT_SYNC state, it needs to ensure that iclog also results in a
cache flush being issued. This covers the case where the iclog
contains the commit record of the CIL flush that the log force
triggered, but it hasn't been written yet because there is still an
active reference to the iclog.
Note: this whole cache flush whack-a-mole patch is a result of log
forces still being iclog state centric rather than being CIL
sequence centric. Most of this nasty code will go away in future
when log forces are converted to wait on CIL sequence push
completion rather than iclog completion. With the CIL push algorithm
guaranteeing that the CIL checkpoint is fully on stable storage when
it completes, we no longer need to iterate iclogs and push them to
ensure a CIL sequence push has completed and so all this nasty iclog
iteration and flushing code will go away.
Fixes: eef983ffea ("xfs: journal IO cache flush reductions")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
We force iclogs in several places - we need them all to have the
same cache flush semantics, so start by factoring out the iclog
force into a common helper.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
There is a race between the new CIL async data device metadata IO
completion cache flush and the log tail in the iclog the flush
covers being updated. This can be seen by repeating generic/482 in a
loop and eventually log recovery fails with a failures such as this:
XFS (dm-3): Starting recovery (logdev: internal)
XFS (dm-3): bad inode magic/vsn daddr 228352 #0 (magic=0)
XFS (dm-3): Metadata corruption detected at xfs_inode_buf_verify+0x180/0x190, xfs_inode block 0x37c00 xfs_inode_buf_verify
XFS (dm-3): Unmount and run xfs_repair
XFS (dm-3): First 128 bytes of corrupted metadata buffer:
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
XFS (dm-3): metadata I/O error in "xlog_recover_items_pass2+0x55/0xc0" at daddr 0x37c00 len 32 error 117
Analysis of the logwrite replay shows that there were no writes to
the data device between the FUA @ write 124 and the FUA at write @
125, but log recovery @ 125 failed. The difference was the one log
write @ 125 moved the tail of the log forwards from (1,8) to (1,32)
and so the inode create intent in (1,8) was not replayed and so the
inode cluster was zero on disk when replay of the first inode item
in (1,32) was attempted.
What this meant was that the journal write that occurred at @ 125
did not ensure that metadata completed before the iclog was written
was correctly on stable storage. The tail of the log moved forward,
so IO must have been completed between the two iclog writes. This
means that there is a race condition between the unconditional async
cache flush in the CIL push work and the tail LSN that is written to
the iclog. This happens like so:
CIL push work AIL push work
------------- -------------
Add to committing list
start async data dev cache flush
.....
<flush completes>
<all writes to old tail lsn are stable>
xlog_write
.... push inode create buffer
<start IO>
.....
xlog_write(commit record)
.... <IO completes>
log tail moves
xlog_assign_tail_lsn()
start_lsn == commit_lsn
<no iclog preflush!>
xlog_state_release_iclog
__xlog_state_release_iclog()
<writes *new* tail_lsn into iclog>
xlog_sync()
....
submit_bio()
<tail in log moves forward without flushing written metadata>
Essentially, this can only occur if the commit iclog is issued
without a cache flush. If the iclog bio is submitted with
REQ_PREFLUSH, then it will guarantee that all the completed IO is
one stable storage before the iclog bio with the new tail LSN in it
is written to the log.
IOWs, the tail lsn that is written to the iclog needs to be sampled
*before* we issue the cache flush that guarantees all IO up to that
LSN has been completed.
To fix this without giving up the performance advantage of the
flush/FUA optimisations (e.g. g/482 runtime halves with 5.14-rc1
compared to 5.13), we need to ensure that we always issue a cache
flush if the tail LSN changes between the initial async flush and
the commit record being written. THis requires sampling the tail_lsn
before we start the flush, and then passing the sampled tail LSN to
xlog_state_release_iclog() so it can determine if the the tail LSN
has changed while writing the checkpoint. If the tail LSN has
changed, then it needs to set the NEED_FLUSH flag on the iclog and
we'll issue another cache flush before writing the iclog.
Fixes: eef983ffea ("xfs: journal IO cache flush reductions")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Fold __xlog_state_release_iclog into its only caller to prepare
make an upcoming fix easier.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
[hch: split from a larger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
The recent journal flush/FUA changes replaced the flushing of the
data device on every iclog write with an up-front async data device
cache flush. Unfortunately, the assumption of which this was based
on has been proven incorrect by the flush vs log tail update
ordering issue. As the fix for that issue uses the
XLOG_ICL_NEED_FLUSH flag to indicate that data device needs a cache
flush, we now need to (once again) ensure that an iclog write to
external logs that need a cache flush to be issued actually issue a
cache flush to the data device as well as the log device.
Fixes: eef983ffea ("xfs: journal IO cache flush reductions")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
We incorrectly flush the log device instead of the data device when
trying to ensure metadata is correctly on disk before writing the
unmount record.
Fixes: eef983ffea ("xfs: journal IO cache flush reductions")
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Hi Mark
Now I'm posting audio-graph-card2 patch-set, but it seems it needs longer
discussion. Thus I want to post more easy patch first, and reduce my
local patches.
These are cppcheck warning cleanup patches for soc-core.
Kuninori Morimoto (7):
ASoC: soc-core: cleanup cppcheck warning at snd_soc_set_dmi_name()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_get_dai_name()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_daifmt_parse_format()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_unregister_component()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_add_controls()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_of_parse_audio_simple_widgets()
ASoC: soc-core: cleanup cppcheck warning at snd_soc_of_parse_audio_routing()
sound/soc/soc-core.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
--
2.25.1
DG2 has some changes to the expected modesetting sequences when compared
to gen12. Adjust our driver logic accordingly. Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.
v2:
- Switch wait_for_us() -> _wait_for() so that we can parameterize the
timeout rather than duplicating the macro call. (Jani)
Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-27-matthew.d.roper@intel.com
Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.
Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com
At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates. The PHY tables
here should support the regular modes of real-world HDMI monitors.
Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com
DG2's SNPS PHYs incorporate a dedicated port PLL called MPLLB which
takes the place of the shared DPLLs we've used on past platforms. Let's
add the MPLLB programming sequences; they'll be plugged into the rest of
the code in future patches.
Bspec: 54032
Bspec: 53881
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Nidhi Gupta <nidhi1.gupta@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-24-matthew.d.roper@intel.com
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy().
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210718131217.3806-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
remove some unused static variables. One of them
is used to toggle on the BT coexistence mechanism,
but it is always enabled and it's not conditioned
to the value of the related parameter.
Remove unused field of the registry_priv struct as
well, they were intended for hosting the parameters
this patch rids.
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/20210729125417.4380-1-fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This use-after-free happens when a fw_priv object has been freed but
hasn't been removed from the pending list (pending_fw_head). The next
time fw_load_sysfs_fallback tries to insert into the list, it ends up
accessing the pending_list member of the previously freed fw_priv.
The root cause here is that all code paths that abort the fw load
don't delete it from the pending list. For example:
_request_firmware()
-> fw_abort_batch_reqs()
-> fw_state_aborted()
To fix this, delete the fw_priv from the list in __fw_set_state() if
the new state is DONE or ABORTED. This way, all aborts will remove
the fw_priv from the list. Accordingly, remove calls to list_del_init
that were being made before calling fw_state_(aborted|done).
Also, in fw_load_sysfs_fallback, don't add the fw_priv to the pending
list if it is already aborted. Instead, just jump out and return early.
Fixes: bcfbd3523f ("firmware: fix a double abort case with fw_load_sysfs_fallback")
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Tested-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210728085107.4141-3-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>