Enable Video Processing Unit to make accelerated video decoding work.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove touchscreen-size-* properties. This values are not correct, event if it
works with ts_test tool, it fails to work properly with weston.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At some point PWM cell count was changed, but it didn't triggered any
error, since this DT was overwriting "#pwm-cells".
To make sure, we are in sync with the kernel driver, remove this
property and fix the pwm consumer.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The backlight power is controlled through the reg_bl_12v0 regulator.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Link: https://lore.kernel.org/r/20210608084816.1046485-1-chenxiaosong2@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Add touchscreen support to the Protonic VT7 board.
Co-Developed-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit d25f6ead16 ("iommu/arm-smmu-v3: Increase maximum size of queues")
expands the cmdq queue size to improve the success rate of concurrent
command queue space allocation by multiple cores. However, this extension
does not apply to evtq and priq, because for both of them, the SMMU driver
is the consumer. Instead, memory resources are wasted. Therefore, the
queue size of evtq and priq is restored to the original setting, one page.
Fixes: d25f6ead16 ("iommu/arm-smmu-v3: Increase maximum size of queues")
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210531123553.9602-1-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
When a device or driver misbehaves, it is possible to receive DMA fault
events much faster than we can print them out, causing a lock up of the
system and inability to cancel the source of the problem. Ratelimit
printing of events to help recovery.
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210531095648.118282-1-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
The SMMU provides a Stall model for handling page faults in platform
devices. It is similar to PCIe PRI, but doesn't require devices to have
their own translation cache. Instead, faulting transactions are parked
and the OS is given a chance to fix the page tables and retry the
transaction.
Enable stall for devices that support it (opt-in by firmware). When an
event corresponds to a translation error, call the IOMMU fault handler.
If the fault is recoverable, it will call us back to terminate or
continue the stall.
To use stall device drivers need to enable IOMMU_DEV_FEAT_IOPF, which
initializes the fault queue for the device.
Tested-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210526161927.24268-4-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Copy the "Stall supported" bit, that tells whether a named component
supports stall, into the dma-can-stall device property.
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210526161927.24268-3-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
On ARM systems, some platform devices behind an IOMMU may support stall,
which is the ability to recover from page faults. Let the firmware tell us
when a device supports stall.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Link: https://lore.kernel.org/r/20210526161927.24268-2-jean-philippe@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
This enables the adreno-specific SMMU path that sets HUPCF so
(user-managed) page faults don't wedge the GPU.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-2-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
db820c wants to use the qcom smmu path to get HUPCF set (which keeps
the GPU from wedging and then sometimes wedging the kernel after a
page fault), but it doesn't have separate pagetables support yet in
drm/msm so we can't go all the way to the TTBR1 path.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210326231303.3071950-1-eric@anholt.net
Signed-off-by: Will Deacon <will@kernel.org>
We need to grab the resv lock first before doing that check.
v2 (chk): simplify the change for -fixes
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210528130041.1683-1-christian.koenig@amd.com
Add his_entry to the reg offsets struct.
This will allow different products to have a different reg offset for this
particular module.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for version register and print it at probe time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DMA submodule is a part of the atmel-isc pipeline, and stands for
Direct Memory Access. It acts like a master on the AXI bus of the SoC, and
can directly write the RAM area with the pixel data from the ISC internal
sram.
Add dma to the reg offsets struct.
This will allow different products to have a different reg offset for this
particular module.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HIS submodule is a part of the atmel-isc pipeline, and stands for
Histogram. This module performs a color histogram that can be read and used
by the main processor.
Add his to the reg offsets struct.
This will allow different products to have a different reg offset for this
particular module.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The RLP submodule is a part of the atmel-isc pipeline, and stands for
Rounding,Limiting and Packaging. It used to extract specific data from the
ISC pipeline. For example if we want to output greyscale 8 bit, we would
use limiting to 8 bits, and packaging to Luma component only.
Add rlp to the reg offsets struct.
This will allow different products to have a different reg offset for this
particular module.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SUB submodules are a part of the atmel-isc pipeline, and stand for
Subsampling. They are used to subsample the original YUV 4:4:4 pixel ratio
aspect to either 4:2:2 or 4:2:0.
Add sub420 and sub422 to the reg offsets struct.
This will allow different products to have a different reg offset for these
particular modules.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CBC submodule is a part of the atmel-isc pipeline, and stands for
Contrast Brightness Control. It is used to apply gains and offsets to the
luma (Y) and chroma (U, V) components of the YUV elements.
Add cbc to the reg offsets struct. This will allow different products
to have a different reg offset for this particular module.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CBC submodule is a part of the atmel-isc pipeline, and stands for
Contrast Brightness Control. It is used to apply gains and offsets to the
luma (Y) and chroma (U, V) components of the YUV elements.
The CBC submodule should be initialized in the product specific driver
as it's product specific. Other products can implement it differently
[hverkuil: made isc_sama5d2_config_cbc static]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create a struct that holds register offsets that are product specific.
Add initially the CSC register.
This allows each product that contains a variant of the ISC to add their
own register offset.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the clock id to the debug message regarding clock setup
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSC submodule is a part of the atmel-isc pipeline, and stands for
Color Space Conversion. It is used to apply a matrix transformation to
RGB pixels to convert them to the YUV components.
The CSC submodule should be initialized in the product specific driver
as it's product specific. Other products can implement it differently.
[hverkuil: made isc_sama5d2_config_csc static]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The dma configuration (DCFG) is specific to the product.
Move this configuration in the product specific driver, and add the
field inside the driver struct.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement a ->probe_finalize() callback that can be used by vendor
implementations to perform extra programming necessary after devices
have been attached to the SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-4-thierry.reding@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Fix checkpatch.pl --strict -f drivers/gpu/drm/bridge/ti-sn65dsi83.c
CHECKs, no functional change. This is the same modification done
to V7 of the original patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608095322.23644-1-marex@denx.de
Let's reserve JSL stolen memory for graphics.
JasperLake is a gen11 platform which is compatible with
ICL/EHL changes.
This was missed in commit 24ea098b7c ("drm/i915/jsl: Split
EHL/JSL platform info and PCI ids")
V2:
- Added maintainer list in cc
- Added patch ref in commit message
V1:
- Added Cc: x86@kernel.org
Fixes: 24ea098b7c ("drm/i915/jsl: Split EHL/JSL platform info and PCI ids")
Cc: <stable@vger.kernel.org> # v5.11+
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608053411.394166-1-tejaskumarx.surendrakumar.upadhyay@intel.com
Move the max width and max height constants to the product specific driver
and have them in the device struct.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling the subdev, certain subdev drivers will overwrite the
frame size and adding sizes which are beyond the ISC's capabilities.
Thus we need to ensure the frame size is cropped to the maximum caps.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver name constant must defined based on product driver, thus moving
the constant directly where it's required. This will allow each ISC based
product to define it's own name.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Separate the gamma table from the isc base file into the specific sama5d2
product file.
Add a pointer to the gamma table and entries count inside the platform
driver specific struct.
[hverkuil: made isc_sama5d2_gamma_table static]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
sps_max_sub_layers_minus1 is needed if the driver wishes to determine
whether or not a frame might be used for reference.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the new vb2_queue_change_type() function in .vidioc_reqbufs and
.vidioc_create_bufs instead of changing the queue type manually in
vidioc_s_fmt_vbi_cap() and vidioc_s_fmt_sliced_vbi_cap().
This allows for a more consistent behavior, as .vidioc_reqbufs and
.vidioc_create_bufs are when the queue will become "busy".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Vivid tracks the VBI capture mode in vivid_dev->stream_sliced_vbi_cap
field. We can just look at the buffer type instead, and drop the field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some platforms a video device can capture either video data or
metadata. The driver can implement vidioc functions for both video and
metadata, and use a single vb2_queue for the buffers. However, vb2_queue
requires choosing a single buffer type, which conflicts with the idea of
capturing either video or metadata.
The buffer type of vb2_queue can be changed, but it's not obvious how
this should be done in the drivers. To help this, add a new helper
function vb2_queue_change_type() which ensures the correct checks and
documents how it can be used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The hookup with qcom_smmu_impl is required to do ACPI boot on SC8180X
based devices like Lenovo Flex 5G laptop and Microsoft Surface Pro X.
Define acpi_platform_list for these platforms and match them using
acpi_match_platform_list() call, and create qcom_smmu_impl accordingly.
(np == NULL) is used to check ACPI boot, because fwnode of SMMU device
is a static allocation and thus helpers like has_acpi_companion() don't
work here.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210509022607.17534-1-shawn.guo@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
We discussed if that is really the right approach for quite a while now, but
digging deeper into a bug report on arm turned out that this is actually
horrible broken right now.
The reason for this is that vmf_insert_mixed_prot() always tries to grab
a reference to the underlaying page on architectures without
ARCH_HAS_PTE_SPECIAL and as far as I can see also enabled GUP.
So nuke using VM_MIXEDMAP here and use VM_PFNMAP instead.
Also make sure to reject mappings without VM_SHARED.
v2: reject COW mappings, merge function with only caller
v3: adjust comment as suggested by Thomas
Signed-off-by: Christian König <christian.koenig@amd.com>
Bugs: https://gitlab.freedesktop.org/drm/amd/-/issues/1606#note_936174
Link: https://patchwork.freedesktop.org/patch/msgid/20210607135830.8574-1-christian.koenig@amd.com
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Add driver for TI SN65DSI83 Single-link DSI to Single-link LVDS bridge
and TI SN65DSI84 Single-link DSI to Dual-link or 2x Single-link LVDS
bridge. TI SN65DSI85 is unsupported due to lack of hardware to test on,
but easy to add.
The driver operates the chip via I2C bus. Currently the LVDS clock are
always derived from DSI clock lane, which is the usual mode of operation.
Support for clock from external oscillator is not implemented, but it is
easy to add if ever needed. Only RGB888 pixel format is implemented, the
LVDS666 is not supported, but could be added if needed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210607174258.16300-2-marex@denx.de
Add DT binding document for TI SN65DSI83 and SN65DSI84 DSI to LVDS bridge.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210607174258.16300-1-marex@denx.de
Syzbot reports that when you have AP_VLAN interfaces that are up
and close the AP interface they belong to, we get a deadlock. No
surprise - since we dev_close() them with the wiphy mutex held,
which goes back into the netdev notifier in cfg80211 and tries to
acquire the wiphy mutex there.
To fix this, we need to do two things:
1) prevent changing iftype while AP_VLANs are up, we can't
easily fix this case since cfg80211 already calls us with
the wiphy mutex held, but change_interface() is relatively
rare in drivers anyway, so changing iftype isn't used much
(and userspace has to fall back to down/change/up anyway)
2) pull the dev_close() loop over VLANs out of the wiphy mutex
section in the normal stop case
Cc: stable@vger.kernel.org
Reported-by: syzbot+452ea4fbbef700ff0a56@syzkaller.appspotmail.com
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Link: https://lore.kernel.org/r/20210517160322.9b8f356c0222.I392cb0e2fa5a1a94cf2e637555d702c7e512c1ff@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a lot of Raspberry Pi specific stuff (neither SoC or board
specific) for the BCM2711 which is currently in the RPi 4 B dts. In order
to avoid copy & paste for every new BCM2711 based Raspberry Pi, move it
into a separate dtsi.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-4-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The BCM2711 has a slightly different VEC than the one found in the older
SoCs. Now that we support the new variant, add its compatible to the
device tree.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210520150344.273900-5-maxime@cerno.tech
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
This reverts commit 278407a53c.
The original change breaks USB config on Raspberry Pi Zero and Pi 4 B,
because it exceeds the total fifo size of 4080. A naive attempt to reduce
g-tx-fifo-size doesn't help on Raspberry Pi Zero. So better go back.
Fixes: 278407a53c ("ARM: dts: bcm283x: increase dwc2's RX FIFO size")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/1622293371-5997-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>