It replaces dc3co_enabled with dc3co_exitline on intel_psr struct. And
it saves dc3co_exitline, not dc3co_enabled, so we can use dc3co_exitline
without intel_crtc_state on other psr internal function like as
intel_psr_enable_source().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-12-lucas.demarchi@intel.com
Today when the DSI controller is paired with the Combo-PHY it
uses the high-speed (HS) Word clock for its low power (LP)
transmit PPI communication to the DPHY. The interface signaling
only changes state at an Escape clock frequency (i.e. its
effectively running on a virtual Tx Escape clock that is controlled
by counters w/in the controller), but all the interface flops are
running off the HS clock.
This has the following drawbacks:
* It is a deviation from the PPI spec which assumes signaling is
running on a physical Escape clock
* The PV timings are over constrained (HS timed to 312.5MHz vs.
an Escape clock of 20MHz max)
This feature is proposing to change the LP Tx communication between
the controller and the DPHY from a virtual Tx Escape clock to a physical
clock.
To do this we need to program two "M" divisors. One for the usual
DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV register and one for MIPIO_DWORD8.
For DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV registers the "M" is calculated
as following
Nt = ceil(f_link/160) (theoretical word clock)
Nact = max[3, Nt + (Nt + 1)%2] (actual word clock)
M = Nact * 8
For MIPIO_DWORD8 register, the divisor "M" is calculated as following
M = (Nact - 1)/2
BSpec: 55171
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-11-lucas.demarchi@intel.com
Update MBUS_CTL register if the 2 mbus can be joined as per the current
DDB allocation and active pipes, also update hashing mode and pipe
select bits as per the sequence mentioned in the bspec.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-10-lucas.demarchi@intel.com
The dbuf slices are going to be split across several MBUS units.
The actual dbuf programming will use offsets relative to the
MBUS unit. To accommodate that we shall store the MBUS relative
offsets into the dbuf_state->ddb[] and crtc_state->plane_ddb*[].
For crtc_state->wm.skl.ddb however we want to stick to global
offsets as we use this to sanity check that the ddb allocations
don't overlap between pipes.
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-9-lucas.demarchi@intel.com
On adlp the two mbuses have two display pipes and
two DBUFS, Pipe A and D on Mbus1 and Pipe B and C on
Mbus2. The Mbus can be joined and all the DBUFS can be
used on Pipe A or B.
Bspec: 49255
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-8-lucas.demarchi@intel.com
Alderlake-P don't have programing sequences for MBUS or DBUF during
display initializaiton, instead it requires programing to those
registers during modeset because it to depend on the pipes left
enabled.
Bspec: 49213
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-7-lucas.demarchi@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
The SoC has 6 DDI ports(DDI A,DDI B and DDI TC1-4.
The first two are connected to combo phys while
the rest are connected to TC phys.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-5-lucas.demarchi@intel.com
XE_LPD reduces the number of regular watermark latency levels from 8
to 6 on non-dgfx platforms. However the hardware also adds a special
purpose SAGV wateramrk (and an accompanying transition watermark) that
will be used by the hardware in place of the level 0 values during SAGV
transitions.
Bspec: 49325, 49326, 50419
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-4-lucas.demarchi@intel.com
Add the qp table for 444 formats, for 8bpc, 10bpc and 12bpc, as given by
the VESA C model for DSC 1.1
v2:
- Add include guard to header (Jani)
- Move the big tables to a .c file (Chris, Jani, Lucas)
v3:
- Make tables 'static const' and add lookup functions to index into
them. (Jani)
v3.1:
- Include missing .h file.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-3-lucas.demarchi@intel.com
Add methods to calculate rc parameters for all bpps, against the fixed
arrays that we already have for 8,10,12 valid o/p bpps, to cover RGB 444
formats. Our hw doesn't support YUV compression yet. The calculations
used here are from VESA C model for DSC 1.1
v2:
- Checkpatch fixes
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Juha-Pekka Heikkil <juha-pekka.heikkila@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Mohammed Khajapasha <mohammed.khajapasha@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-2-lucas.demarchi@intel.com
The immediate problem is that after commit
0bd3f9e953 ("powerpc/legacy_serial: Use early_ioremap()") the kernel
silently reboots on some systems.
The reason is that early_ioremap() returns broken addresses as it uses
slot_virt[] array which initialized with offsets from FIXADDR_TOP ==
IOREMAP_END+FIXADDR_SIZE == KERN_IO_END - FIXADDR_SIZ + FIXADDR_SIZE ==
__kernel_io_end which is 0 when early_ioremap_setup() is called.
__kernel_io_end is initialized little bit later in early_init_mmu().
This fixes the initialization by swapping early_ioremap_setup() and
early_init_mmu().
Fixes: 265c3491c4 ("powerpc: Add support for GENERIC_EARLY_IOREMAP")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Drop unrelated cleanup & cleanup change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210520032919.358935-1-aik@ozlabs.ru
Using list_del_init() instead of list_del() + INIT_LIST_HEAD()
to simpify the code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
'ret' is known to be 0 here.
The last error code is stored in 'nr_opp', so use it in the error message.
Fixes: 71a37cd6a5 ("scmi-cpufreq: Remove deferred probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add compatible stirng for MediaTek MT8365 SoC. Add also the
compatible in the blacklist of the cpufreq-dt-platdev driver.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The CLKSCREW attack [0] exposed security vulnerabilities in energy management
implementations where untrusted software had direct access to clock and
voltage hardware controls. In this attack, the malicious software was able to
place the platform into unsafe overclocked or undervolted configurations. Such
configurations then enabled the injection of predictable faults to reveal
secrets.
Many Arm-based systems used to or still use voltage regulator and clock
frameworks in the kernel. These frameworks allow callers to independently
manipulate frequency and voltage settings. Such implementations can render
systems susceptible to this form of attack.
Attacks such as CLKSCREW are now being mitigated by not having direct and
independent control of clock and voltage in the kernel and moving that
control to a trusted entity, such as the SCP firmware or secure world
firmware/software which are to perform sanity checking on the requested
performance levels, thereby preventing any attempted malicious programming.
With the advent of such an abstraction, there is a need to replace the
generic clock and regulator bindings used by such devices with a generic
performance domains bindings.
[0] https://www.usenix.org/conference/usenixsecurity17/technical-sessions/presentation/tang
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add SC7280 to cpufreq-dt-platdev blacklist since the actual scaling is
handled by the 'qcom-cpufreq-hw' driver.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Access to those must be prevented post pci_remove
v6: Drop BOs list, unampping VRAM BAR is enough.
v8:
Add condition of xgmi.connected_to_cpu to MTTR
handling and remove MTTR handling from the old place.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517193105.491461-1-andrey.grodzovsky@amd.com
Problem: If scheduler is already stopped by the time sched_entity
is released and entity's job_queue not empty I encountred
a hang in drm_sched_entity_flush. This is because drm_sched_entity_is_idle
never becomes false.
Fix: In drm_sched_fini detach all sched_entities from the
scheduler's run queues. This will satisfy drm_sched_entity_is_idle.
Also wakeup all those processes stuck in sched_entity flushing
as the scheduler main thread which wakes them up is stopped by now.
v2:
Reverse order of drm_sched_rq_remove_entity and marking
s_entity as stopped to prevent reinserion back to rq due
to race.
v3:
Drop drm_sched_rq_remove_entity, only modify entity->stopped
and check for it in drm_sched_entity_is_idle
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-14-andrey.grodzovsky@amd.com
Return DRM_TASK_STATUS_ENODEV back to the scheduler when device
is not present so they timeout timer will not be rearmed.
v5: Update to match updated return values in enum drm_gpu_sched_stat
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-12-andrey.grodzovsky@amd.com
This should prevent writing to memory or IO ranges possibly
already allocated for other uses after our device is removed.
v5:
Protect more places wher memcopy_to/form_io takes place
Protect IB submissions
v6: Switch to !drm_dev_enter instead of scoping entire code
with brackets.
v7:
Drop guard of HW ring commands emission protection since they
are in GART and not in MMIO.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-10-andrey.grodzovsky@amd.com
This allows to remove explicit creation and destruction
of those attrs and by this avoids warnings on device
finalizing post physical device extraction.
v5: Use newly added pci_driver.dev_groups directly
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-9-andrey.grodzovsky@amd.com
Problem:
Handle all DMA IOMMU group related dependencies before the
group is removed. Those manifest themself in that when IOMMU
enabled DMA map/unmap is dependent on the presence of IOMMU
group the device belongs to but, this group is released once
the device is removed from PCI topology.
Fix:
Expedite all such unmap operations to pci remove driver callback.
v5: Drop IOMMU notifier and switch to lockless call to ttm_tt_unpopulate
v6: Drop the BO unamp list
v7:
Drop amdgpu_gart_fini
In amdgpu_ih_ring_fini do uncinditional check (!ih->ring)
to avoid freeing uniniitalized rings.
Call amdgpu_ih_ring_fini unconditionally.
v8: Add deatiled explanation
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517143851.475058-1-andrey.grodzovsky@amd.com
Use it to call disply code dependent on device->drv_data
before it's set to NULL on device unplug
v5:
Move HW finilization into this callback to prevent MMIO accesses
post cpi remove.
v7:
Split kfd suspend from device exit to expdite HW related
stuff to amdgpu_pci_remove
v8:
Squash previous KFD commit into this commit to avoid compile break.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520032057.497334-1-andrey.grodzovsky@amd.com
Some of the stuff in amdgpu_device_fini such as HW interrupts
disable and pending fences finilization must be done right away on
pci_remove while most of the stuff which relates to finilizing and
releasing driver data structures can be kept until
drm_driver.release hook is called, i.e. when the last device
reference is dropped.
v4: Change functions prefix early->hw and late->sw
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-3-andrey.grodzovsky@amd.com
On device removal reroute all CPU mappings to dummy page.
v3:
Remove loop to find DRM file and instead access it
by vma->vm_file->private_data. Move dummy page installation
into a separate function.
v4:
Map the entire BOs VA space into on demand allocated dummy page
on the first fault for that BO.
v5: Remove duplicate return.
v6: Polish ttm_bo_vm_dummy_page, remove superfluous code.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-2-andrey.grodzovsky@amd.com
Set err code in the error path before jumping to the end of the function.
Fixes: 4dc3bab868 ("PM / devfreq: Add support delayed timer for polling mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This unfortunately comes up in regular intervals and breaks
GPU reset for the engine in question.
The sched.ready flag controls if an engine can't get working
during hw_init, but should never be set to false during hw_fini.
v2: squash in unused variable fix (Alex)
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting from Navi+, the rlc reference clock is used for system clock
from vbios gfx_info table. It is incorrect to use core_refclk_10khz of
vbios smu_info table as system clock.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current golden setting is out of date.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current golden setting is out of date.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To stay consistent with the user's setting.
v2: rebase on multi-eDP support
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1337
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And cache the value. These can be used by the backlight callbacks
and modesetting functions.
v2: rebase on latest backlight changes.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1337
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Aldebaran, driver needs to query DramMegaBaseAddress to
check if DF hashing is enabled.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add video_codecs query support for aldebaran.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function kfd_lookup_process_by_pasid will increase the reference
count of kfd_process object, its caller should call kfd_unref_process to
decrease the reference count. Otherwise resource leakage will happen.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dmabuf attachment should be updated by moving the SG BO to DOMAIN_CPU
and back to DOMAIN_GTT. This does not necessarily invoke the
populate/unpopulate callbacks. Do this in backend_bind/unbind instead.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use DMABufs with dynamic attachment to DMA-map GTT BOs on other GPUs.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to avoid deadlocks with DMA buf import in the next patch.
Also move PT/PD validation out of kfd_mem_attach, that way the caller
can bo this unconditionally.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMA map kfd_mem_attachments in update_gpuvm_pte. This function is called
with the BO and page tables reserved, so we can safely update the DMA
mapping.
DMA unmap when a BO is unmapped from a GPU and before updating mappings
in restore workers.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Acked-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>