[ Upstream commit 73b24dc731 ]
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. scpi_cpufreq_get_rate() does not check for
this case, which results in a NULL pointer dereference.
Fixes: 343a8d17fa ("cpufreq: scpi: remove arm_big_little dependency")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484d3f15cc ]
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. scmi_cpufreq_get_rate() does not check for
this case, which results in a NULL pointer dereference.
Add NULL check after cpufreq_cpu_get_raw() to prevent this issue.
Fixes: 99d6bdf338 ("cpufreq: add support for CPU DVFS based on SCMI message protocol")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9992649f67 ]
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. apple_soc_cpufreq_get_rate() does not check
for this case, which results in a NULL pointer dereference.
Fixes: 6286bbb405 ("cpufreq: apple-soc: Add new driver to control Apple SoC CPU P-states")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7b98ae522 ]
When building with W=1, this variable is unused for configs with
CONFIG_CMA_SIZE_SEL_PERCENTAGE=y:
kernel/dma/contiguous.c:67:26: error: 'size_bytes' defined but not used [-Werror=unused-const-variable=]
Change this to a macro to avoid the warning.
Fixes: c64be2bb1c ("drivers: add Contiguous Memory Allocator")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250409151557.3890443-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14c8a41815 ]
A KASAN enabled kernel reports an out-of-bounds access when handling the
nvmem cell in the sun50i cpufreq driver:
==================================================================
BUG: KASAN: slab-out-of-bounds in sun50i_cpufreq_nvmem_probe+0x180/0x3d4
Read of size 4 at addr ffff000006bf31e0 by task kworker/u16:1/38
This is because the DT specifies the nvmem cell as covering only two
bytes, but we use a u32 pointer to read the value. DTs for other SoCs
indeed specify 4 bytes, so we cannot just shorten the variable to a u16.
Fortunately nvmem_cell_read() allows to return the length of the nvmem
cell, in bytes, so we can use that information to only access the valid
portion of the data.
To cover multiple cell sizes, use memcpy() to copy the information into a
zeroed u32 buffer, then also make sure we always read the data in little
endian fashion, as this is how the data is stored in the SID efuses.
Fixes: 6cc4bcceff ("cpufreq: sun50i: Refactor speed bin decoding")
Reported-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f452a22046 ]
In ceph, in fill_fscrypt_truncate(), the end flush position is calculated
by:
loff_t lend = orig_pos + CEPH_FSCRYPT_BLOCK_SHIFT - 1;
but that's using the block shift not the block size.
Fix this to use the block size instead.
Fixes: 5c64737d25 ("ceph: add truncate size handling support for fscrypt")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cdc2e1d9d9 upstream.
CONFIG_UBSAN_INTEGER_WRAP is 'default UBSAN', which is problematic for a
couple of reasons.
The first is that this sanitizer is under active development on the
compiler side to come up with a solution that is maintainable on the
compiler side and usable on the kernel side. As a result of this, there
are many warnings when the sanitizer is enabled that have no clear path
to resolution yet but users may see them and report them in the meantime.
The second is that this option was renamed from
CONFIG_UBSAN_SIGNED_WRAP, meaning that if a configuration has
CONFIG_UBSAN=y but CONFIG_UBSAN_SIGNED_WRAP=n and it is upgraded via
olddefconfig (common in non-interactive scenarios such as CI),
CONFIG_UBSAN_INTEGER_WRAP will be silently enabled again.
Remove 'default UBSAN' from CONFIG_UBSAN_INTEGER_WRAP until it is ready
for regular usage and testing from a broader community than the folks
actively working on the feature.
Cc: stable@vger.kernel.org
Fixes: 557f8c582a ("ubsan: Reintroduce signed overflow sanitizer")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250414-drop-default-ubsan-integer-wrap-v1-1-392522551d6b@kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
[nathan: Fix conflict due to lack of rename from ed2b548f10 in stable]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd9e6d6fdd ]
The structures are large and they do not require contiguous
memory so use vzalloc.
Fixes: 70839da636 ("drm/amd/display: Add new DCN401 sources")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4126
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 20c50a9a79)
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c299cb6eaf ]
This patch addresses warnings produced by the checkpatch script
related to unnecessary casts that could potentially hide bugs.
The specific warnings are as follows:
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:16
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:20
- Warning at drivers/gpu/drm/amd/display/dc/dml2/dml21/dml21_wrapper.c:30
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rohit Chavan <roheetchavan@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: cd9e6d6fdd ("drm/amd/display/dml2: use vzalloc rather than kzalloc")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5529df92b8 ]
One additional BMG PCI ID has been added to the spec; make sure our
driver recognizes devices with this ID properly.
Bspec: 68090
Cc: stable@vger.kernel.org # v6.12+
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250325224709.4073080-2-matthew.d.roper@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit cca9734ebe)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbb429ddff ]
Fix niu_try_msix() to not cause a fatal trap on sparc systems.
Set PCI_DEV_FLAGS_MSIX_TOUCH_ENTRY_DATA_FIRST on the struct pci_dev to
work around a bug in the hardware or firmware.
For each vector entry in the msix table, niu chips will cause a fatal
trap if any registers in that entry are read before that entries'
ENTRY_DATA register is written to. Testing indicates writes to other
registers are not sufficient to prevent the fatal trap, however the value
does not appear to matter. This only needs to happen once after power up,
so simply rebooting into a kernel lacking this fix will NOT cause the
trap.
NON-RESUMABLE ERROR: Reporting on cpu 64
NON-RESUMABLE ERROR: TPC [0x00000000005f6900] <msix_prepare_msi_desc+0x90/0xa0>
NON-RESUMABLE ERROR: RAW [4010000000000016:00000e37f93e32ff:0000000202000080:ffffffffffffffff
NON-RESUMABLE ERROR: 0000000800000000:0000000000000000:0000000000000000:0000000000000000]
NON-RESUMABLE ERROR: handle [0x4010000000000016] stick [0x00000e37f93e32ff]
NON-RESUMABLE ERROR: type [precise nonresumable]
NON-RESUMABLE ERROR: attrs [0x02000080] < ASI sp-faulted priv >
NON-RESUMABLE ERROR: raddr [0xffffffffffffffff]
NON-RESUMABLE ERROR: insn effective address [0x000000c50020000c]
NON-RESUMABLE ERROR: size [0x8]
NON-RESUMABLE ERROR: asi [0x00]
CPU: 64 UID: 0 PID: 745 Comm: kworker/64:1 Not tainted 6.11.5 #63
Workqueue: events work_for_cpu_fn
TSTATE: 0000000011001602 TPC: 00000000005f6900 TNPC: 00000000005f6904 Y: 00000000 Not tainted
TPC: <msix_prepare_msi_desc+0x90/0xa0>
g0: 00000000000002e9 g1: 000000000000000c g2: 000000c50020000c g3: 0000000000000100
g4: ffff8000470307c0 g5: ffff800fec5be000 g6: ffff800047a08000 g7: 0000000000000000
o0: ffff800014feb000 o1: ffff800047a0b620 o2: 0000000000000011 o3: ffff800047a0b620
o4: 0000000000000080 o5: 0000000000000011 sp: ffff800047a0ad51 ret_pc: 00000000005f7128
RPC: <__pci_enable_msix_range+0x3cc/0x460>
l0: 000000000000000d l1: 000000000000c01f l2: ffff800014feb0a8 l3: 0000000000000020
l4: 000000000000c000 l5: 0000000000000001 l6: 0000000020000000 l7: ffff800047a0b734
i0: ffff800014feb000 i1: ffff800047a0b730 i2: 0000000000000001 i3: 000000000000000d
i4: 0000000000000000 i5: 0000000000000000 i6: ffff800047a0ae81 i7: 00000000101888b0
I7: <niu_try_msix.constprop.0+0xc0/0x130 [niu]>
Call Trace:
[<00000000101888b0>] niu_try_msix.constprop.0+0xc0/0x130 [niu]
[<000000001018f840>] niu_get_invariants+0x183c/0x207c [niu]
[<00000000101902fc>] niu_pci_init_one+0x27c/0x2fc [niu]
[<00000000005ef3e4>] local_pci_probe+0x28/0x74
[<0000000000469240>] work_for_cpu_fn+0x8/0x1c
[<000000000046b008>] process_scheduled_works+0x144/0x210
[<000000000046b518>] worker_thread+0x13c/0x1c0
[<00000000004710e0>] kthread+0xb8/0xc8
[<00000000004060c8>] ret_from_fork+0x1c/0x2c
[<0000000000000000>] 0x0
Kernel panic - not syncing: Non-resumable error.
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Jonathan Currier <dullfire@yahoo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241117234843.19236-3-dullfire@yahoo.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f92bb74368 ]
If dma-coherent property isn't set then descriptors are non-cacheable
and the iocc shareability bits should be disabled. Without this UFS can
end up in an incompatible configuration and suffer from random cache
related stability issues.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Fixes: cc52e15397 ("scsi: ufs: ufs-exynos: Support ExynosAuto v9 UFS")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-3-96722cc2ba1b@linaro.org
Cc: Chanho Park <chanho61.park@samsung.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f5ef7eeb ]
gs101 I/O coherency shareability bits differ from exynosauto SoC. To
support both SoCs move this info the SoC drvdata.
Currently both the value and mask are the same for both gs101 and
exynosauto, thus we use the same value.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-2-96722cc2ba1b@linaro.org
Fixes: d11e0a318d ("scsi: ufs: exynos: Add support for Tensor gs101 SoC")
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc4a4a576 ]
Factor out the common code into a new exynos_ufs_shareability() function
and provide a dedicated gs101_drv_init() hook.
This allows us to enable WriteBooster capability (UFSHCD_CAP_WB_EN) in a
way that doesn't effect other SoCs supported in this driver.
WriteBooster improves write speeds by enabling a pseudo SLC cache. Using
the 'fio seqwrite' test we can achieve speeds of 945MB/s with this
feature enabled (until the cache is exhausted) before dropping back to
~260MB/s (which are the speeds we see without the WriteBooster feature
enabled).
Assuming the UFSHCD_CAP_WB_EN capability is set by the host then
WriteBooster can also be enabled and disabled via sysfs so it is
possible for the system to only enable it when extra write performance
is required.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-10-peter.griffin@linaro.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd613ca2c ]
The pointer to device can be obtained from ufs->hba->dev, remove
superfluous function parameter.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-3-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07c2a73750 ]
Remove empty method. When the method is not set, the call is not made,
saving a few cycles.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20241031150033.3440894-2-peter.griffin@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: 68f5ef7eeb ("scsi: ufs: exynos: Move UFS shareability value to drvdata")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21a4e47578 ]
Move tcp_transport free to ksmbd_conn_free. If ksmbd connection is
referenced when ksmbd server thread terminates, It will not be freed,
but conn->tcp_transport is freed. __smb2_lease_break_noti can be performed
asynchronously when the connection is disconnected. __smb2_lease_break_noti
calls ksmbd_conn_write, which can cause use-after-free
when conn->ksmbd_transport is already freed.
Cc: stable@vger.kernel.org
Reported-by: Norbert Szetei <norbert@doyensec.com>
Tested-by: Norbert Szetei <norbert@doyensec.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2d99376c5 ]
ksmbd.mount will give each interfaces list and bind_interfaces_only flags
to ksmbd server. Previously, the interfaces list was sent only
when bind_interfaces_only was enabled.
ksmbd server browse only interfaces list given from ksmbd.conf on
FSCTL_QUERY_INTERFACE_INFO IOCTL.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 21a4e47578 ("ksmbd: fix use-after-free in __smb2_lease_break_noti()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0066f623bc ]
Prefer to report ENOMEM rather than incur the oom for allocations in
ksmbd. __GFP_NORETRY could not achieve that, It would fail the allocations
just too easily. __GFP_RETRY_MAYFAIL will keep retrying the allocation
until there is no more progress and fail the allocation instead go OOM
and let the caller to deal with it.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 21a4e47578 ("ksmbd: fix use-after-free in __smb2_lease_break_noti()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c2b75404d ]
Fix the frequency returned to the user space by
the DRM_IVPU_PARAM_CORE_CLOCK_RATE GET_PARAM IOCTL.
The kernel driver returned CPU frequency for MTL and bare
PLL frequency for LNL - this was inconsistent and incorrect
for both platforms. With this fix the driver returns maximum
frequency of the NPU data processing unit (DPU) for all HW
generations. This is what user space always expected.
Also do not set CPU frequency in boot params - the firmware
does not use frequency passed from the driver, it was only
used by the early pre-production firmware.
With that we can remove CPU frequency calculation code.
Show NPU frequency in FREQ_CHANGE interrupt when frequency
tracking is enabled.
Fixes: 8a27ad81f7 ("accel/ivpu: Split IP and buttress code")
Cc: stable@vger.kernel.org # v6.11+
Signed-off-by: Andrzej Kacprowski <Andrzej.Kacprowski@intel.com>
Signed-off-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://lore.kernel.org/r/20250401155912.4049340-2-maciej.falkowski@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 436b67d693 ]
Add ivpu_fw_sched_mode_select() function that can select scheduling mode
based on HW and FW versions. This prepares for a switch to HWS on
selected platforms.
Reviewed-by: Karol Wachowski <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930195322.461209-17-jacek.lawrynowicz@linux.intel.com
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Stable-dep-of: 6c2b75404d ("accel/ivpu: Fix the NPU's DPU frequency calculation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf761e3dac ]
Commit 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries") introduced a
readl() from ENTRY_VECTOR_CTRL before the writel() to ENTRY_DATA.
This is correct, however some hardware, like the Sun Neptune chips, the NIU
module, will cause an error and/or fatal trap if any MSIX table entry is
read before the corresponding ENTRY_DATA field is written to.
Add an optional early writel() in msix_prepare_msi_desc().
Fixes: 7d5ec3d361 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Jonathan Currier <dullfire@yahoo.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/20241117234843.19236-2-dullfire@yahoo.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ece3e8e59 ]
The conversion of the XEN specific global variable pci_msi_ignore_mask to a
MSI domain flag, missed the facts that:
1) Legacy architectures do not provide a interrupt domain
2) Parent MSI domains do not necessarily have a domain info attached
Both cases result in an unconditional NULL pointer dereference. This was
unfortunatly missed in review and testing revealed it late.
Cure this by using the existing pci_msi_domain_supports() helper, which
handles all possible cases correctly.
Fixes: c3164d2e0d ("PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag")
Reported-by: Daniel Gomez <da.gomez@kernel.org>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Borislav Petkov <bp@alien8.de>
Tested-by: Daniel Gomez <da.gomez@kernel.org>
Link: https://lore.kernel.org/all/87iknwyp2o.ffs@tglx
Closes: https://lore.kernel.org/all/qn7fzggcj6qe6r6gdbwcz23pzdz2jx64aldccmsuheabhmjgrt@tawf5nfwuvw7
Stable-dep-of: cf761e3dac ("PCI/MSI: Add an option to write MSIX ENTRY_DATA before any reads")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3164d2e0d ]
Setting pci_msi_ignore_mask inhibits the toggling of the mask bit for both
MSI and MSI-X entries globally, regardless of the IRQ chip they are using.
Only Xen sets the pci_msi_ignore_mask when routing physical interrupts over
event channels, to prevent PCI code from attempting to toggle the maskbit,
as it's Xen that controls the bit.
However, the pci_msi_ignore_mask being global will affect devices that use
MSI interrupts but are not routing those interrupts over event channels
(not using the Xen pIRQ chip). One example is devices behind a VMD PCI
bridge. In that scenario the VMD bridge configures MSI(-X) using the
normal IRQ chip (the pIRQ one in the Xen case), and devices behind the
bridge configure the MSI entries using indexes into the VMD bridge MSI
table. The VMD bridge then demultiplexes such interrupts and delivers to
the destination device(s). Having pci_msi_ignore_mask set in that scenario
prevents (un)masking of MSI entries for devices behind the VMD bridge.
Move the signaling of no entry masking into the MSI domain flags, as that
allows setting it on a per-domain basis. Set it for the Xen MSI domain
that uses the pIRQ chip, while leaving it unset for the rest of the
cases.
Remove pci_msi_ignore_mask at once, since it was only used by Xen code, and
with Xen dropping usage the variable is unneeded.
This fixes using devices behind a VMD bridge on Xen PV hardware domains.
Albeit Devices behind a VMD bridge are not known to Xen, that doesn't mean
Linux cannot use them. By inhibiting the usage of
VMD_FEAT_CAN_BYPASS_MSI_REMAP and the removal of the pci_msi_ignore_mask
bodge devices behind a VMD bridge do work fine when use from a Linux Xen
hardware domain. That's the whole point of the series.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Message-ID: <20250219092059.90850-4-roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Stable-dep-of: cf761e3dac ("PCI/MSI: Add an option to write MSIX ENTRY_DATA before any reads")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded40f32b5 ]
The driver leaks the device reference taken with
of_find_device_by_node(). Fix the leak by using devm_of_qcom_ice_get().
Fixes: 56541c7c44 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com> # SCSI
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250117-qcom-ice-fix-dev-leak-v2-3-1ffa5b6884cb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a46a080563 ]
In of_resolve_phandles(), refcount of device node @local_fixups will be
increased if the for_each_child_of_node() exits early, but nowhere to
decrease the refcount, so cause refcount leakage for the node.
Fix by using __free() on @local_fixups.
Fixes: da56d04c80 ("of/resolver: Switch to new local fixups format.")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-9-93e3a2659aa7@quicinc.com
[robh: Use __free() instead]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5275e8b529 ]
Use the __free() cleanup to simplify of_resolve_phandles() and remove
all the goto's.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Stable-dep-of: a46a080563 ("of: resolver: Fix device node refcount leakage in of_resolve_phandles()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38e7f9092e ]
Commit under Fixes added the 'idle-states' property for SERDES4 lane muxes
without defining the corresponding register offsets and masks for it in the
'mux-reg-masks' property within the 'serdes_ln_ctrl' node.
Fix this.
Fixes: 7287d423f1 ("arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux")
Cc: stable@vger.kernel.org
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20250228053850.506028-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8236644f5e ]
The ad7768-1 ADC output code is two's complement, meaning that the voltage
conversion result is a signed value.. Since the value is a 24 bit one,
stored in a 32 bit variable, the sign should be extended in order to get
the correct representation.
Also the channel description has been updated to signed representation,
to match the ADC specifications.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://patch.msgid.link/505994d3b71c2aa38ba714d909a68e021f12124c.1741268122.git.Jonathan.Santos@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0af1c801a1 ]
The data used is all in local variables so there is no advantage
in setting *val = ret with the direct mode claim held.
Move it later to after error check.
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250217141630.897334-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 8236644f5e ("iio: adc: ad7768-1: Fix conversion result sign")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9a457722c ]
The VTU registers of the 6320 family use the 6352 semantics, not 6185.
Fix it.
Fixes: b8fee95710 ("net: dsa: mv88e6xxx: add VLAN Get Next support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: <stable@vger.kernel.org> # 5.15.x
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250317173250.28780-2-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc0e982b8a ]
Make sure ->nr_integrity_segments is cloned in blk_rq_prep_clone(),
otherwise requests cloned by device-mapper multipath will not have the
proper nr_integrity_segments values set, then BUG() is hit from
sg_alloc_table_chained().
Fixes: b0fd271d5f ("block: add request clone interface (v2)")
Cc: stable@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20250310115453.2271109-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6975c1a486 ]
The request ioprio is only initialized from the first attached bio,
so requests without a bio already never set it. Directly use the
bio field instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241112170050.1612998-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: fc0e982b8a ("block: make sure ->nr_integrity_segments is cloned in blk_rq_prep_clone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61952bb734 ]
The write_hint is only used for read/write requests, which must have a
bio attached to them. Just use the bio field instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241112170050.1612998-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: fc0e982b8a ("block: make sure ->nr_integrity_segments is cloned in blk_rq_prep_clone")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebf185efad ]
The driver might skip the ov08x40_identify_module() on probe() based on
the acpi_dev_state_d0() check done in probe().
If the ov08x40_identify_module() call is skipped on probe() it should
be done on the first stream start. Add the missing call.
Note ov08x40_identify_module() will only do something on its first call,
subsequent calls are no-ops.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b1a42fde6e ("media: ov08x40: Avoid sensor probing in D0 state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a39639e44 ]
Move the ov08x40_identify_module() function to above ov08x40_set_stream()
this is a preparation patch for adding a missing ov08x40_identify_module()
call to ov08x40_set_stream().
No functional changes, just moving code around.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: ebf185efad ("media: ov08x40: Add missing ov08x40_identify_module() call on stream-start")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acc294519f ]
The driver defines IMX214_DEFAULT_LINK_FREQ 480000000, and then
IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10),
which works out as 384MPix/s. (The 8 is 4 lanes and DDR.)
Parsing the PLL registers with the defined 24MHz input. We're in single
PLL mode, so MIPI frequency is directly linked to pixel rate. VTCK ends
up being 1200MHz, and VTPXCK and OPPXCK both are 120MHz. Section 5.3
"Frame rate calculation formula" says "Pixel rate
[pixels/s] = VTPXCK [MHz] * 4", so 120 * 4 = 480MPix/s, which basically
agrees with my number above.
3.1.4. MIPI global timing setting says "Output bitrate = OPPXCK * reg
0x113[7:0]", so 120MHz * 10, or 1200Mbit/s. That would be a link
frequency of 600MHz due to DDR.
That also matches to 480MPix/s * 10bpp / 4 lanes / 2 for DDR.
Keep the previous link frequency for backward compatibility.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d55f4eb03 ]
The imx214 camera is capable of either two-lane or four-lane operation.
Currently only the four-lane mode is supported, as proper pixel rates
and link frequences for the two-lane mode are unknown.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 341a133beb ]
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f0aeba4f1 ]
Use the new common CCI register access helpers to replace the private
register access helpers in the imx214 driver. This simplifies the driver
by reducing the amount of code.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d6dc133e6 ]
Error handling in probe() can be a bit simpler with dev_err_probe().
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6832ff659 ]
Port the imx214 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
While at it, simplify imx214_start_streaming() by removing unneeded goto
statements and the corresponding error label.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Stable-dep-of: acc294519f ("media: i2c: imx214: Fix link frequency validation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1618f635bd ]
The callback function of call_rcu() just calls kfree(), so use
kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://patch.msgid.link/20250218082021.2766-1-lirongqing@baidu.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 3ee7be9e10 ("PM: EM: Address RCU-related sparse warnings")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbef7442fb ]
The driver leaks the device reference taken with
of_find_device_by_node(). Fix the leak by using devm_of_qcom_ice_get().
Fixes: c7eed31e23 ("mmc: sdhci-msm: Switch to the new ICE API")
Cc: stable@vger.kernel.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250117-qcom-ice-fix-dev-leak-v2-2-1ffa5b6884cb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c13d6060d ]
Callers of of_qcom_ice_get() leak the device reference taken by
of_find_device_by_node(). Introduce devm variant for of_qcom_ice_get().
Existing consumers need the ICE instance for the entire life of their
device, thus exporting qcom_ice_put() is not required.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250117-qcom-ice-fix-dev-leak-v2-1-1ffa5b6884cb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stable-dep-of: cbef7442fb ("mmc: sdhci-msm: fix dev reference leaked through of_qcom_ice_get")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b0449544c ]
Syzkaller reports a bug as follows:
Injecting memory failure for pfn 0x18b00e at process virtual address 0x20ffd000
Memory failure: 0x18b00e: dirty swapcache page still referenced by 2 users
Memory failure: 0x18b00e: recovery action for dirty swapcache page: Failed
page: refcount:2 mapcount:0 mapping:0000000000000000 index:0x20ffd pfn:0x18b00e
memcg:ffff0000dd6d9000
anon flags: 0x5ffffe00482011(locked|dirty|arch_1|swapbacked|hwpoison|node=0|zone=2|lastcpupid=0xfffff)
raw: 005ffffe00482011 dead000000000100 dead000000000122 ffff0000e232a7c9
raw: 0000000000020ffd 0000000000000000 00000002ffffffff ffff0000dd6d9000
page dumped because: VM_BUG_ON_FOLIO(!folio_test_uptodate(folio))
------------[ cut here ]------------
kernel BUG at mm/swap_state.c:184!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Modules linked in:
CPU: 0 PID: 60 Comm: kswapd0 Not tainted 6.6.0-gcb097e7de84e #3
Hardware name: linux,dummy-virt (DT)
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : add_to_swap+0xbc/0x158
lr : add_to_swap+0xbc/0x158
sp : ffff800087f37340
x29: ffff800087f37340 x28: fffffc00052c0380 x27: ffff800087f37780
x26: ffff800087f37490 x25: ffff800087f37c78 x24: ffff800087f377a0
x23: ffff800087f37c50 x22: 0000000000000000 x21: fffffc00052c03b4
x20: 0000000000000000 x19: fffffc00052c0380 x18: 0000000000000000
x17: 296f696c6f662865 x16: 7461646f7470755f x15: 747365745f6f696c
x14: 6f6621284f494c4f x13: 0000000000000001 x12: ffff600036d8b97b
x11: 1fffe00036d8b97a x10: ffff600036d8b97a x9 : dfff800000000000
x8 : 00009fffc9274686 x7 : ffff0001b6c5cbd3 x6 : 0000000000000001
x5 : ffff0000c25896c0 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : ffff0000c25896c0 x0 : 0000000000000000
Call trace:
add_to_swap+0xbc/0x158
shrink_folio_list+0x12ac/0x2648
shrink_inactive_list+0x318/0x948
shrink_lruvec+0x450/0x720
shrink_node_memcgs+0x280/0x4a8
shrink_node+0x128/0x978
balance_pgdat+0x4f0/0xb20
kswapd+0x228/0x438
kthread+0x214/0x230
ret_from_fork+0x10/0x20
I can reproduce this issue with the following steps:
1) When a dirty swapcache page is isolated by reclaim process and the
page isn't locked, inject memory failure for the page.
me_swapcache_dirty() clears uptodate flag and tries to delete from lru,
but fails. Reclaim process will put the hwpoisoned page back to lru.
2) The process that maps the hwpoisoned page exits, the page is deleted
the page will never be freed and will be in the lru forever.
3) If we trigger a reclaim again and tries to reclaim the page,
add_to_swap() will trigger VM_BUG_ON_FOLIO due to the uptodate flag is
cleared.
To fix it, skip the hwpoisoned page in shrink_folio_list(). Besides, the
hwpoison folio may not be unmapped by hwpoison_user_mappings() yet, unmap
it in shrink_folio_list(), otherwise the folio will fail to be unmaped by
hwpoison_user_mappings() since the folio isn't in lru list.
Link: https://lkml.kernel.org/r/20250318083939.987651-3-tujinjiang@huawei.com
Signed-off-by: Jinjiang Tu <tujinjiang@huawei.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Nanyong Sun <sunnanyong@huawei.com>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: <stable@vger,kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea8d7647f9 ]
The trace event verifier checks the formats of trace events to make sure
that they do not point at memory that is not in the trace event itself or
in data that will never be freed. If an event references data that was
allocated when the event triggered and that same data is freed before the
event is read, then the kernel can crash by reading freed memory.
The verifier runs at boot up (or module load) and scans the print formats
of the events and checks their arguments to make sure that dereferenced
pointers are safe. If the format uses "%*p.." the verifier will ignore it,
and that could be dangerous. Cover this case as well.
Also add to the sample code a use case of "%*pbl".
Link: https://lore.kernel.org/all/bcba4d76-2c3f-4d11-baf0-02905db953dd@oracle.com/
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 5013f454a3 ("tracing: Add check of trace event print fmts for dereferencing pointers")
Link: https://lore.kernel.org/20250327195311.2d89ec66@gandalf.local.home
Reported-by: Libo Chen <libo.chen@oracle.com>
Reviewed-by: Libo Chen <libo.chen@oracle.com>
Tested-by: Libo Chen <libo.chen@oracle.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
