commit 5f465c148c upstream.
Initialize DR6 by writing its architectural reset value to avoid
incorrectly zeroing DR6 to clear DR6.BLD at boot time, which leads
to a false bus lock detected warning.
The Intel SDM says:
1) Certain debug exceptions may clear bits 0-3 of DR6.
2) BLD induced #DB clears DR6.BLD and any other debug exception
doesn't modify DR6.BLD.
3) RTM induced #DB clears DR6.RTM and any other debug exception
sets DR6.RTM.
To avoid confusion in identifying debug exceptions, debug handlers
should set DR6.BLD and DR6.RTM, and clear other DR6 bits before
returning.
The DR6 architectural reset value 0xFFFF0FF0, already defined as
macro DR6_RESERVED, satisfies these requirements, so just use it to
reinitialize DR6 whenever needed.
Since clear_all_debug_regs() no longer zeros all debug registers,
rename it to initialize_debug_regs() to better reflect its current
behavior.
Since debug_read_clear_dr6() no longer clears DR6, rename it to
debug_read_reset_dr6() to better reflect its current behavior.
Fixes: ebb1064e7c ("x86/traps: Handle #DB for bus lock")
Reported-by: Sohil Mehta <sohil.mehta@intel.com>
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Reviewed-by: Sohil Mehta <sohil.mehta@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Sohil Mehta <sohil.mehta@intel.com>
Link: https://lore.kernel.org/lkml/06e68373-a92b-472e-8fd9-ba548119770c@intel.com/
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20250620231504.2676902-2-xin%40zytor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3f3040657 upstream.
Each Chip-Select (CS) of a Unified Memory Controller (UMC) on AMD Zen-based
SOCs has an Address Mask and a Secondary Address Mask register associated with
it. The amd64_edac module logs DIMM sizes on a per-UMC per-CS granularity
during init using these two registers.
Currently, the module primarily considers only the Address Mask register for
computing DIMM sizes. The Secondary Address Mask register is only considered
for odd CS. Additionally, if it has been considered, the Address Mask register
is ignored altogether for that CS. For power-of-two DIMMs i.e. DIMMs whose
total capacity is a power of two (32GB, 64GB, etc), this is not an issue
since only the Address Mask register is used.
For non-power-of-two DIMMs i.e., DIMMs whose total capacity is not a power of
two (48GB, 96GB, etc), however, the Secondary Address Mask register is used
in conjunction with the Address Mask register. However, since the module only
considers either of the two registers for a CS, the size computed by the
module is incorrect. The Secondary Address Mask register is not considered for
even CS, and the Address Mask register is not considered for odd CS.
Introduce a new helper function so that both Address Mask and Secondary
Address Mask registers are considered, when valid, for computing DIMM sizes.
Furthermore, also rename some variables for greater clarity.
Fixes: 81f5090db8 ("EDAC/amd64: Support asymmetric dual-rank DIMMs")
Closes: https://lore.kernel.org/dbec22b6-00f2-498b-b70d-ab6f8a5ec87e@natrix.lt
Reported-by: Žilvinas Žaltiena <zilvinas@natrix.lt>
Signed-off-by: Avadhut Naik <avadhut.naik@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Žilvinas Žaltiena <zilvinas@natrix.lt>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/20250529205013.403450-1-avadhut.naik@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 263debecb4 ]
When performing a file read from RDMA, smbd_recv() prints an "Invalid msg
type 4" error and fails the I/O. This is due to the switch-statement there
not handling the ITER_FOLIOQ handed down from netfslib.
Fix this by collapsing smbd_recv_buf() and smbd_recv_page() into
smbd_recv() and just using copy_to_iter() instead of memcpy(). This
future-proofs the function too, in case more ITER_* types are added.
Fixes: ee4cdf7ba8 ("netfs: Speed up buffered reading")
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Talpey <tom@talpey.com>
cc: Paulo Alcantara (Red Hat) <pc@manguebit.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43e7e284fc ]
The handling of received data in the smbdirect client code involves using
copy_to_iter() to copy data from the smbd_reponse struct's packet trailer
to a folioq buffer provided by netfslib that encapsulates a chunk of
pagecache.
If, however, CONFIG_HARDENED_USERCOPY=y, this will result in the checks
then performed in copy_to_iter() oopsing with something like the following:
CIFS: Attempting to mount //172.31.9.1/test
CIFS: VFS: RDMA transport established
usercopy: Kernel memory exposure attempt detected from SLUB object 'smbd_response_0000000091e24ea1' (offset 81, size 63)!
------------[ cut here ]------------
kernel BUG at mm/usercopy.c:102!
...
RIP: 0010:usercopy_abort+0x6c/0x80
...
Call Trace:
<TASK>
__check_heap_object+0xe3/0x120
__check_object_size+0x4dc/0x6d0
smbd_recv+0x77f/0xfe0 [cifs]
cifs_readv_from_socket+0x276/0x8f0 [cifs]
cifs_read_from_socket+0xcd/0x120 [cifs]
cifs_demultiplex_thread+0x7e9/0x2d50 [cifs]
kthread+0x396/0x830
ret_from_fork+0x2b8/0x3b0
ret_from_fork_asm+0x1a/0x30
The problem is that the smbd_response slab's packet field isn't marked as
being permitted for usercopy.
Fix this by passing parameters to kmem_slab_create() to indicate that
copy_to_iter() is permitted from the packet region of the smbd_response
slab objects, less the header space.
Fixes: ee4cdf7ba8 ("netfs: Speed up buffered reading")
Reported-by: Stefan Metzmacher <metze@samba.org>
Link: https://lore.kernel.org/r/acb7f612-df26-4e2a-a35d-7cd040f513e1@samba.org/
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
Tested-by: Stefan Metzmacher <metze@samba.org>
cc: Paulo Alcantara <pc@manguebit.com>
cc: linux-cifs@vger.kernel.org
cc: netfs@lists.linux.dev
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc55f65dd3 ]
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce8047f47 ]
This is the next step in the direction of a common smbdirect layer.
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3011b9a7d ]
This is the next step in the direction of a common smbdirect layer.
Currently only structures are shared, but that will change
over time until everything is shared.
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22234e37d7 ]
This abstracts the common smbdirect layer.
Currently with just a few things in it,
but that will change over time until everything is
in common.
Will be used in client and server in the next commits
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e136a7186 ]
Will be used in client and server in the next commits.
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
CC: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64946d5be6 ]
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00fab6cf32 ]
This is just a start moving into a common smbdirect layer.
It will be used in the next commits...
Cc: Steve French <smfrench@gmail.com>
Cc: Tom Talpey <tom@talpey.com>
Cc: Long Li <longli@microsoft.com>
Cc: Namjae Jeon <linkinjeon@kernel.org>
Cc: Hyunchul Lee <hyc.lee@gmail.com>
Cc: Meetakshi Setiya <meetakshisetiyaoss@gmail.com>
Cc: linux-cifs@vger.kernel.org
Cc: samba-technical@lists.samba.org
Signed-off-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: 43e7e284fc ("cifs: Fix the smbd_response slab to allow usercopy")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55e8ff8420 ]
By default, HPD was disabled on SN65DSI86 bridge. When the driver was
added (commit "a095f15c00e27"), the HPD_DISABLE bit was set in pre-enable
call which was moved to other function calls subsequently.
Later on, commit "c312b0df3b" added detect utility for DP mode. But with
HPD_DISABLE bit set, all the HPD events are disabled[0] and the debounced
state always return 1 (always connected state).
Set HPD_DISABLE bit conditionally based on display sink's connector type.
Since the HPD_STATE is reflected correctly only after waiting for debounce
time (~100-400ms) and adding this delay in detect() is not feasible
owing to the performace impact (glitches and frame drop), remove runtime
calls in detect() and add hpd_enable()/disable() bridge hooks with runtime
calls, to detect hpd properly without any delay.
[0]: <https://www.ti.com/lit/gpn/SN65DSI86> (Pg. 32)
Fixes: c312b0df3b ("drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP")
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250624044835.165708-1-j-choudhary@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d1f7b15cb ]
Do not create a custom directory in debugfs-root, but use the
debugfs_init callback to create a custom directory at the given place
for the bridge. The new directory layout looks like this on a Renesas
GrayHawk-Single with a R-Car V4M SoC:
/sys/kernel/debug/dri/feb00000.display/DP-1/1-002c
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250315201651.7339-2-wsa+renesas@sang-engineering.com
Stable-dep-of: 55e8ff8420 ("drm/bridge: ti-sn65dsi86: Add HPD for DisplayPort connector type")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d02b2103a0 ]
An earlier patch fixed a build failure with clang, but I still see the
same problem with some configurations using gcc:
drivers/gpu/drm/i915/i915_pmu.c: In function 'config_mask':
include/linux/compiler_types.h:568:38: error: call to '__compiletime_assert_462' declared with attribute error: BUILD_BUG_ON failed: bit > BITS_PER_TYPE(typeof_member(struct i915_pmu, enable)) - 1
drivers/gpu/drm/i915/i915_pmu.c:116:3: note: in expansion of macro 'BUILD_BUG_ON'
116 | BUILD_BUG_ON(bit >
As I understand it, the problem is that the function is not always fully
inlined, but the __builtin_constant_p() can still evaluate the argument
as being constant.
Marking it as __always_inline so far works for me in all configurations.
Fixes: a7137b1825 ("drm/i915/pmu: Fix build error with GCOV and AutoFDO enabled")
Fixes: a644fde77f ("drm/i915/pmu: Change bitmask of enabled events to u32")
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250620111824.3395007-1-arnd@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit ef69f9dd1c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73eab78721 ]
commit 017fbb6690 ("drm/amdgpu/discovery: check ip_discovery fw file
available") added support for reading an amdgpu IP discovery bin file
for some specific products. If it's not found then it will fallback to
hardcoded values. However if it's not found there is also a lot of noise
about missing files and errors.
Adjust the error handling to decrease most messages to DEBUG and to show
users less about missing files.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reported-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4312
Tested-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Fixes: 017fbb6690 ("drm/amdgpu/discovery: check ip_discovery fw file available")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250617183052.1692059-1-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 49f1f9f6c3)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80a0e82829 ]
On chips without native IP discovery support, use the fw binary
if available, otherwise we can continue without it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 73eab78721 ("drm/amd: Adjust output for discovery error handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d89661a36 ]
The length in the pseudo header should be the length of the L3 payload
AKA the L4 header+payload. The selftest code builds the packet from
the lower layers up, so all the headers are pushed already when it
constructs L4. We need to subtract the lower layer headers from skb->len.
Fixes: 3e1e58d64c ("net: add generic selftest support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20250624183258.3377740-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ab6847a03 ]
The built-in mic of ASUS VivoBook X507UAR is broken recently by the fix
of the pin sort. The fixup ALC256_FIXUP_ASUS_MIC_NO_PRESENCE is working
for addressing the regression, too.
Fixes: 3b4309546b ("ALSA: hda: Fix headset detection failure due to unstable sort")
Reported-by: Igor Tamara <igor.tamara@gmail.com>
Closes: https://bugs.debian.org/1108069
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Link: https://lore.kernel.org/CADdHDco7_o=4h_epjEAb92Dj-vUz_PoTC2-W9g5ncT2E0NzfeQ@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eef0eaeca7 ]
We're trying to add a strict regexp for the name format in the spec.
Underscores will not be allowed, dashes should be used instead.
This makes no difference to C (codegen, if used, replaces special
chars in names) but it gives more uniform naming in Python.
Fixes: a1bcfde836 ("doc/netlink/specs: Add a spec for tc")
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250624211002.3475021-10-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b515f35a9 ]
enetc_hw.h provides two versions of _enetc_rd_reg64.
One which simply calls ioread64() when available.
And another that composes the 64-bit result from ioread32() calls.
In the second case the code appears to assume that each ioread32() call
returns a little-endian value. However both the shift and logical or
used to compose the return value would not work correctly on big endian
systems if this were the case. Moreover, this is inconsistent with the
first case where the return value of ioread64() is assumed to be in host
byte order.
It appears that the correct approach is for both versions to treat the
return value of ioread*() functions as being in host byte order. And
this patch corrects the ioread32()-based version to do so.
This is a bug but would only manifest on big endian systems
that make use of the ioread32-based implementation of _enetc_rd_reg64.
While all in-tree users of this driver are little endian and
make use of the ioread64-based implementation of _enetc_rd_reg64.
Thus, no in-tree user of this driver is affected by this bug.
Flagged by Sparse.
Compile tested only.
Fixes: 16eb4c85c9 ("enetc: Add ethtool statistics")
Closes: https://lore.kernel.org/all/AM9PR04MB850500D3FC24FE23DEFCEA158879A@AM9PR04MB8505.eurprd04.prod.outlook.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250624-etnetc-le-v1-1-a73a95d96e4e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa6f092cc0 ]
The `name` field in `obj->externs` points into the BTF data at initial
open time. However, some functions may invalidate this after opening and
before loading (e.g. `bpf_map__set_value_size`), which results in
pointers into freed memory and undefined behavior.
The simplest solution is to simply `strdup` these strings, similar to
the `essent_name`, and free them at the same time.
In order to test this path, the `global_map_resize` BPF selftest is
modified slightly to ensure the presence of an extern, which causes this
test to fail prior to the fix. Given there isn't an obvious API or error
to test against, I opted to add this to the existing test as an aspect
of the resizing feature rather than duplicate the test.
Fixes: 9d0a23313b ("libbpf: Add capability for resizing datasec maps")
Signed-off-by: Adin Scannell <amscanne@meta.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250625050215.2777374-1-amscanne@meta.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55c7a85e0 ]
The subsequent call to os_set_fd_block() overwrites the previous
return value. OR the two return values together to fix it.
Fixes: f88f0bdfc3 ("um: UBD Improvements")
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Link: https://patch.msgid.link/20250606124428.148164-2-tiwei.btw@antgroup.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 22bbc1dcd0 ]
If a userspace application just include <linux/vm_sockets.h> will fail
to build with the following errors:
/usr/include/linux/vm_sockets.h:182:39: error: invalid application of ‘sizeof’ to incomplete type ‘struct sockaddr’
182 | unsigned char svm_zero[sizeof(struct sockaddr) -
| ^~~~~~
/usr/include/linux/vm_sockets.h:183:39: error: ‘sa_family_t’ undeclared here (not in a function)
183 | sizeof(sa_family_t) -
|
Include <sys/socket.h> for userspace (guarded by ifndef __KERNEL__)
where `struct sockaddr` and `sa_family_t` are defined.
We already do something similar in <linux/mptcp.h> and <linux/if.h>.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reported-by: Daan De Meyer <daan.j.demeyer@gmail.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://patch.msgid.link/20250623100053.40979-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90233b0ad2 ]
Currently, MLD links for an AP_VLAN interface type is not fully
supported.
Add allocation of separate links for each VLAN interface and copy
chanctx and chandef of AP bss to VLAN where necessary. Separate
links are created because for Dynamic VLAN each link will have its own
default_multicast_key.
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250325213125.1509362-3-muna.sinada@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: d87c3ca0f8 ("wifi: mac80211: finish link init before RCU publish")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61c7b3d44 ]
Currently before iterating through valid links we are utilizing
open-coding when checking if vif valid_links is a non-zero value.
Add new macro, for_each_link_data(), which iterates through link_id
and checks if it is set on vif valid_links. If it is a valid link then
access link data for that link id.
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Link: https://patch.msgid.link/20250325213125.1509362-2-muna.sinada@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: d87c3ca0f8 ("wifi: mac80211: finish link init before RCU publish")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5a484184 ]
Christian Brauner reported that even after MSG_OOB data is consumed,
calling close() on the receiver socket causes the peer's recv() to
return -ECONNRESET:
1. send() and recv() an OOB data.
>>> from socket import *
>>> s1, s2 = socketpair(AF_UNIX, SOCK_STREAM)
>>> s1.send(b'x', MSG_OOB)
1
>>> s2.recv(1, MSG_OOB)
b'x'
2. close() for s2 sets ECONNRESET to s1->sk_err even though
s2 consumed the OOB data
>>> s2.close()
>>> s1.recv(10, MSG_DONTWAIT)
...
ConnectionResetError: [Errno 104] Connection reset by peer
Even after being consumed, the skb holding the OOB 1-byte data stays in
the recv queue to mark the OOB boundary and break recv() at that point.
This must be considered while close()ing a socket.
Let's skip the leading consumed OOB skb while checking the -ECONNRESET
condition in unix_release_sock().
Fixes: 314001f0bf ("af_unix: Add OOB support")
Reported-by: Christian Brauner <brauner@kernel.org>
Closes: https://lore.kernel.org/netdev/20250529-sinkt-abfeuern-e7b08200c6b0@brauner/
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Link: https://patch.msgid.link/20250619041457.1132791-4-kuni1840@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a3750ff0f ]
As we are converting from TU to usecs, a beacon interval of
100*1024 usecs will lead to integer wrapping. To fix change
to use a u32.
Fixes: 057d5f4ba1 ("mac80211: sync dtim_count to TSF")
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250621123209.511796-1-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5e3241c5a ]
Change error values of `ionic_tx_map_single()` and `ionic_tx_map_frag()`
from 0 to `DMA_MAPPING_ERROR` to prevent collision with 0 as a valid
address.
This also fixes the use of `dma_mapping_error()` to test against 0 in
`ionic_xdp_post_frame()`
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Fixes: 56e41ee12d ("ionic: better dma-map error handling")
Fixes: ac8813c0ab ("ionic: convert Rx queue buffers to use page_pool")
Signed-off-by: Thomas Fourier <fourier.thomas@gmail.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20250619094538.283723-2-fourier.thomas@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa485e8789 ]
When btf_dump__new() fails to allocate memory for the internal hashmap
(btf_dump->type_names), it returns an error code. However, the cleanup
function btf_dump__free() does not check if btf_dump->type_names is NULL
before attempting to free it. This leads to a null pointer dereference
when btf_dump__free() is called on a btf_dump object.
Fixes: 351131b51c ("libbpf: add btf_dump API for BTF-to-C conversion")
Signed-off-by: Yuan Chen <chenyuan@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20250618011933.11423-1-chenyuan_fl@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce7df19686 ]
If we are propagating across the userns boundary, we need to lock the
mounts added there. However, in case when something has already
been mounted there and we end up sliding a new tree under that,
the stuff that had been there before should not get locked.
IOW, lock_mnt_tree() should be called before we reparent the
preexisting tree on top of what we are adding.
Fixes: 3bd045cc9c ("separate copying and locking mount tree on cross-userns copies")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb4e2a6e8f ]
In snd_usb_get_audioformat_uac3(), the length value returned from
snd_usb_ctl_msg() is used directly for memory allocation without
validation. This length is controlled by the USB device.
The allocated buffer is cast to a uac3_cluster_header_descriptor
and its fields are accessed without verifying that the buffer
is large enough. If the device returns a smaller than expected
length, this leads to an out-of-bounds read.
Add a length check to ensure the buffer is large enough for
uac3_cluster_header_descriptor.
Signed-off-by: Youngjun Lee <yjjuny.lee@samsung.com>
Fixes: 9a2fe9b801 ("ALSA: usb: initial USB Audio Device Class 3.0 support")
Link: https://patch.msgid.link/20250623-uac3-oob-fix-v1-1-527303eaf40a@samsung.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6123102e ]
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/namei.c:4046
do_filp_open+0x1fa/0x410 fs/namei.c:4073
do_sys_openat2+0x121/0x1c0 fs/open.c:1437
do_sys_open fs/open.c:1452 [inline]
__do_sys_openat fs/open.c:1468 [inline]
__se_sys_openat fs/open.c:1463 [inline]
__x64_sys_openat+0x138/0x170 fs/open.c:1463
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2381 [inline]
slab_free mm/slub.c:4643 [inline]
kfree+0x18e/0x440 mm/slub.c:4842
vhci_release+0xbc/0xd0 drivers/bluetooth/hci_vhci.c:671
__fput+0x44c/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x6ad/0x22e0 kernel/exit.c:955
do_group_exit+0x21c/0x2d0 kernel/exit.c:1104
__do_sys_exit_group kernel/exit.c:1115 [inline]
__se_sys_exit_group kernel/exit.c:1113 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1113
x64_sys_call+0x21ba/0x21c0 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff88807cb8d800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 88 bytes inside of
freed 1024-byte region [ffff88807cb8d800, ffff88807cb8dc00)
Fixes: bf18c7118c ("Bluetooth: vhci: Free driver_data on file release")
Reported-by: syzbot+2faa4825e556199361f9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f62d64848fc4c7c30cd6
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b993ea46b3 ]
Blamed commit missed that vcc_destroy_socket() calls
clip_push() with a NULL skb.
If clip_devs is NULL, clip_push() then crashes when reading
skb->truesize.
Fixes: 93a2014afb ("atm: fix a UAF in lec_arp_clear_vccs()")
Reported-by: syzbot+1316233c4c6803382a8b@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/68556f59.a00a0220.137b3.004e.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Gengming Liu <l.dmxcsnsbh@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f3054152c1 ]
Commit fd2a9b29dc ("HID: wacom: Remove AES power_supply after extended
inactivity") introduced wacom_aes_battery_handler() which is scheduled
as a delayed work (aes_battery_work).
In wacom_remove(), aes_battery_work is not canceled. Consequently, if
the device is removed while aes_battery_work is still pending, then hard
crashes or "Oops: general protection fault..." are experienced when
wacom_aes_battery_handler() is finally called. E.g., this happens with
built-in USB devices after resume from hibernate when aes_battery_work
was still pending at the time of hibernation.
So, take care to cancel aes_battery_work in wacom_remove().
Fixes: fd2a9b29dc ("HID: wacom: Remove AES power_supply after extended inactivity")
Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at>
Acked-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6220729347 upstream.
Add check for the return value of alloc_ordered_workqueue()
in xe_display_create() to catch potential exception.
Fixes: 44e694958b ("drm/xe/display: Implement display support")
Cc: stable@vger.kernel.org
Signed-off-by: Haoxiang Li <haoxiang_li2024@163.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://lore.kernel.org/r/4ee1b0e5d1626ce1dde2e82af05c2edaed50c3aa.1747397638.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 5b62d63395)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f73c62d4e upstream.
This reverts commit 61a74ad254 ("riscv: misaligned: fix sleeping function
called during misaligned access handling"). The commit addresses a sleeping
in atomic context problem, but it is not the correct fix as explained by
Clément:
"Using nofault would lead to failure to read from user memory that is paged
out for instance. This is not really acceptable, we should handle user
misaligned access even at an address that would generate a page fault."
This bug has been properly fixed by commit 453805f0a2 ("riscv:
misaligned: enable IRQs while handling misaligned accesses").
Revert this improper fix.
Link: https://lore.kernel.org/linux-riscv/b779beed-e44e-4a5e-9551-4647682b0d21@rivosinc.com/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: 61a74ad254 ("riscv: misaligned: fix sleeping function called during misaligned access handling")
Link: https://lore.kernel.org/r/20250620110939.1642735-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890ba5be63 upstream.
This reverts commit ad5643cf2f ("riscv: Define TASK_SIZE_MAX for
__access_ok()").
This commit changes TASK_SIZE_MAX to be LONG_MAX to optimize access_ok(),
because the previous TASK_SIZE_MAX (default to TASK_SIZE) requires some
computation.
The reasoning was that all user addresses are less than LONG_MAX, and all
kernel addresses are greater than LONG_MAX. Therefore access_ok() can
filter kernel addresses.
Addresses between TASK_SIZE and LONG_MAX are not valid user addresses, but
access_ok() let them pass. That was thought to be okay, because they are
not valid addresses at hardware level.
Unfortunately, one case is missed: get_user_pages_fast() happily accepts
addresses between TASK_SIZE and LONG_MAX. futex(), for instance, uses
get_user_pages_fast(). This causes the problem reported by Robert [1].
Therefore, revert this commit. TASK_SIZE_MAX is changed to the default:
TASK_SIZE.
This unfortunately reduces performance, because TASK_SIZE is more expensive
to compute compared to LONG_MAX. But correctness first, we can think about
optimization later, if required.
Reported-by: <rtm@csail.mit.edu>
Closes: https://lore.kernel.org/linux-riscv/77605.1750245028@localhost/
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Fixes: ad5643cf2f ("riscv: Define TASK_SIZE_MAX for __access_ok()")
Link: https://lore.kernel.org/r/20250619155858.1249789-1-namcao@linutronix.de
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df831e9773 upstream.
While testing null_blk with configfs, echo 0 > poll_queues will trigger
following panic:
BUG: kernel NULL pointer dereference, address: 0000000000000010
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 27 UID: 0 PID: 920 Comm: bash Not tainted 6.15.0-02023-gadbdb95c8696-dirty #1238 PREEMPT(undef)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:__bitmap_or+0x48/0x70
Call Trace:
<TASK>
__group_cpus_evenly+0x822/0x8c0
group_cpus_evenly+0x2d9/0x490
blk_mq_map_queues+0x1e/0x110
null_map_queues+0xc9/0x170 [null_blk]
blk_mq_update_queue_map+0xdb/0x160
blk_mq_update_nr_hw_queues+0x22b/0x560
nullb_update_nr_hw_queues+0x71/0xf0 [null_blk]
nullb_device_poll_queues_store+0xa4/0x130 [null_blk]
configfs_write_iter+0x109/0x1d0
vfs_write+0x26e/0x6f0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x45c4/0x45f0
do_syscall_64+0xa5/0x240
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Root cause is that numgrps is set to 0, and ZERO_SIZE_PTR is returned from
kcalloc(), and later ZERO_SIZE_PTR will be deferenced.
Fix the problem by checking numgrps first in group_cpus_evenly(), and
return NULL directly if numgrps is zero.
[yukuai3@huawei.com: also fix the non-SMP version]
Link: https://lkml.kernel.org/r/20250620010958.1265984-1-yukuai1@huaweicloud.com
Link: https://lkml.kernel.org/r/20250619132655.3318883-1-yukuai1@huaweicloud.com
Fixes: 6a6dcae8f4 ("blk-mq: Build default queue map via group_cpus_evenly()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Cc: ErKun Yang <yangerkun@huawei.com>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: "zhangyi (F)" <yi.zhang@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a5e85f4eb upstream.
is_zero_pfn() does not work for the huge zero folio. Fix it by using
is_huge_zero_pmd().
This can cause the PAGEMAP_SCAN ioctl against /proc/pid/pagemap to
present pages as PAGE_IS_PRESENT rather than as PAGE_IS_PFNZERO.
Found by code inspection.
Link: https://lkml.kernel.org/r/20250617143532.2375383-1-david@redhat.com
Fixes: 52526ca7fd ("fs/proc/task_mmu: implement IOCTL to get and optionally clear info about PTEs")
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7360ee4759 upstream.
Number of apqn target list entries contained in 'nr_apqns' variable is
determined by userspace via an ioctl call so the result of the product in
calculation of size passed to memdup_user() may overflow.
In this case the actual size of the allocated area and the value
describing it won't be in sync leading to various types of unpredictable
behaviour later.
Use a proper memdup_array_user() helper which returns an error if an
overflow is detected. Note that it is different from when nr_apqns is
initially zero - that case is considered valid and should be handled in
subsequent pkey_handler implementations.
Found by Linux Verification Center (linuxtesting.org).
Fixes: f2bbc96e7c ("s390/pkey: add CCA AES cipher key support")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20250611192011.206057-1-pchelkin@ispras.ru
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f489fe6af upstream.
memcg_path_store() assigns a newly allocated memory buffer to
filter->memcg_path, without deallocating the previously allocated and
assigned memory buffer. As a result, users can leak kernel memory by
continuously writing a data to memcg_path DAMOS sysfs file. Fix the leak
by deallocating the previously set memory buffer.
Link: https://lkml.kernel.org/r/20250619183608.6647-2-sj@kernel.org
Fixes: 7ee161f18b ("mm/damon/sysfs-schemes: implement filter directory")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: Shuah Khan <shuah@kernel.org>
Cc: <stable@vger.kernel.org> [6.3.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e0809b166 upstream.
ASUS store the board name in DMI_PRODUCT_NAME rather than
DMI_PRODUCT_VERSION. (Apparently it is only Lenovo that stores the
model-name in DMI_PRODUCT_VERSION.)
Use the correct DMI identifier, DMI_PRODUCT_NAME, to match the
ASUSPRO-D840SA board, such that the quirk actually gets applied.
Cc: stable@vger.kernel.org
Reported-by: Andy Yang <andyybtc79@gmail.com>
Tested-by: Andy Yang <andyybtc79@gmail.com>
Closes: https://lore.kernel.org/linux-ide/aFb3wXAwJSSJUB7o@ryzen/
Fixes: b5acc36288 ("ata: ahci: Disallow LPM for ASUSPRO-D840SA motherboard")
Reviewed-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250624074029.963028-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56ad91c1aa upstream.
This driver passes the length of an i2c_msg directly to
usb_control_msg(). If the message is now a read and of length 0, it
violates the USB protocol and a warning will be printed. Enable the
I2C_AQ_NO_ZERO_LEN_READ quirk for this adapter thus forbidding 0-length
read messages altogether.
Fixes: 83e53a8f12 ("i2c: Add bus driver for for OSIF USB i2c device.")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522064234.3721-2-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
