Implement support for using the values given in the
isil,battery-trip-levels-microvolt property to set appropriate values
in the VB85TP/VB75TP bits in the PWR_VBAT register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-5-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The isl12022 has a built-in support for monitoring the voltage of the
backup battery, and setting bits in the status register when that
voltage drops below two predetermined levels (usually 85% and 75% of
the nominal voltage). However, since it can operate at wide range of
battery voltages (2.5V - 5.5V), one must configure those trip levels
according to which battery is used on a given board.
Add bindings for defining these two trip levels. While the register
and bit names suggest that they should correspond to 85% and 75% of
the nominal battery voltage, the data sheet also says
There are total of 7 levels that could be selected for the first
alarm. Any of the of levels could be selected as the first alarm
with no reference as to nominal Battery voltage level.
Hence this provides the hardware designer the ability to choose values
based on the discharge characteristics of the battery chosen for the
given product, rather than just having one battery-microvolt property
and having the driver choose levels close to 0.85/0.75 times that.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230615105826.411953-4-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move the isil,isl12022 RTC bindings from trivial-rtc.yaml into its own
intersil,isl12022.yaml file, in preparation for adding more bindings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-3-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There are multiple problems with this warning.
First of all, it triggers way too often, in fact nearly on every boot,
because the SR_LBAT85/SR_LBAT75 bits have another meaning when in
battery backup mode. Quoting from the data sheet:
LOW BATTERY INDICATOR 85% BIT (LBAT85)
In Normal Mode (VDD), this bit indicates when the battery level has
dropped below the pre-selected trip levels. [...] The LBAT85
detection happens automatically once every minute when seconds
register reaches 59.
In Battery Mode (VBAT), this bit indicates the device has entered
into battery mode by polling once every 10 minutes. The LBAT85
detection happens automatically once when the minute register
reaches x9h or x0h minutes.
Similar wording applies to the LBAT75 bit.
This means that if the device is powered off for more than 10 minutes,
the LBAT85 bit is guaranteed to be set. Upon power-on, unless we're
close enough to the end of a minute and/or the boot is slow enough
that the second register passes 59, the LBAT85 bit is still set when
the kernel (or early userspace) reads the RTC to set the system's
wallclock time.
Another minor problem is with the bit logic. If the 75% level is
reached, logically we're also below 85%, so both bits would most
likely be set. So even if the battery is below 75%, the warning would
still say "voltage dropped below 85%".
A third problem is that the driver and current DT binding offer no way
to indicate the nominal battery level and/or settings of the Battery
Level Monitor Trip Bits. Since the default value of the VB85TP[2:0] and
VB75TP[2:0] bits are 000, this means the actual setting of the
LBAT85/LBAT75 bits in VDD mode doesn't happen until the battery is below
2.125V/1.875V, which for a standard 3V battery is way too late.
A fourth problem is emitting this warning from ->read_time:
util-linux' hwclock will, in the absence of support for getting an
interrupt when the seconds counter is updated, issue
ioctl(RTC_RD_TIME) in a busy-loop until it sees a change in the
seconds field. In that case, if the battery low bits are set (either
genuinely, more than a minute after boot, due to the battery actually
being low, or as above, bogusly shortly after boot), the kernel log is
swamped with hundreds of identical warnings.
Subsequent patches will add such bindings and driver support, and also
proper support for RTC_VL_READ. For now, remove the broken warning.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230615105826.411953-2-linux@rasmusvillemoes.dk
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Referring to platform_get_irq()'s definition, the return value has
already been checked if ret < 0, and printed via dev_err_probe().
Calling dev_err_probe() one more time outside platform_get_irq()
is obviously redundant.
Removing dev_err_probe() outside platform_get_irq() to clean up
above problem.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Link: https://lore.kernel.org/r/20230802093650.976352-1-chenjiahao16@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
After a previous commit changed the driver over to
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(), the suspend/resume
functions must no longer be hidden behind an #ifdef:
In file included from include/linux/clk.h:13,
from drivers/rtc/rtc-stm32.c:8:
drivers/rtc/rtc-stm32.c:927:39: error: 'stm32_rtc_suspend' undeclared here (not in a function); did you mean 'stm32_rtc_probe'?
927 | SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(stm32_rtc_suspend, stm32_rtc_resume)
| ^~~~~~~~~~~~~~~~~
include/linux/kernel.h:58:44: note: in definition of macro 'PTR_IF'
58 | #define PTR_IF(cond, ptr) ((cond) ? (ptr) : NULL)
| ^~~
include/linux/pm.h:329:26: note: in expansion of macro 'pm_sleep_ptr'
329 | .suspend_noirq = pm_sleep_ptr(suspend_fn), \
| ^~~~~~~~~~~~
Fixes: fb9a7e5360 ("rtc: stm32: change PM callbacks to "_noirq()"")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230801105932.3738430-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The driver was introduced when .probe_new was the right probe callback
to use for i2c drivers. Today .probe is the right one (again) and the
driver was already switched in commit 31b0cecb40 ("rtc: Switch i2c
drivers back to use .probe()") but the name continued to include "_new"
in its name.
To prevent code readers wondering about what might be new here, drop
that irritating part of the name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230725070429.383070-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230724205456.767430-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Property "trickle-resistor-ohms" allows us to set trickle charger
resistor. However there is no possibility to disable it afterwards.
Add support for "aux-voltage-chargeable" property which can be used to
enable/disable the trickle charger circuit explicitly. The default
behavior of the code is kept as it is!
Additionally, lets make sure we only update internal EEPROM in case of a
change. This prevents wear due to excessive EEPROM writes on each probe.
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Link: https://lore.kernel.org/r/20230623081533.76334-1-andrej.picej@norik.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The added HAS_IOPORT dependency might not actually be necessary as Geert
points out, but the driver is also only used on one architecture. Sparc
is also a special case here since it converts port numbers into virtual
addresses rather than having them mapped into a particular part of the
__iomem address space, so the difference is actually not important here.
Add a dependency on sparc, but allow compile-testing otherwise, to
make this clearer without anyone having to spend much time modernizing
the driver beyond that.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/all/CAMuHMdWEx0F=fNei4Bz_JPkuvoaN-+zk08h0i8KnSi_VjO615g@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230719192835.1025406-1-arnd@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Drop enum pcf85063_type and split the array pcf85063_cfg[] as individual
variables, and make lines shorter by referring to e.g. &pcf85063_cfg
instead of &pcf85063_cfg[PCF85063].
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230717124059.196244-3-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The pcf85063_ids[].driver_data could store a pointer to the config,
like for DT-based matching, making I2C and DT-based matching
more similar.
After that, we can simplify the probe() by replacing of_device_get_
match_data() and i2c_match_id() by i2c_get_match_data() as we have
similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230717124059.196244-2-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230710114747.106496-1-biju.das.jz@bp.renesas.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a few style issues reported by checkpatch.pl:
- Unnecessary parentheses
- Lines should not end with a '('
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-8-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
stm32_rtc_valid_alrm function has some issues :
- arithmetical operations are impossible on BCD values
- "cur_mon + 1" can overflow
- the use case with the next month, the same day/hour/minutes went wrong
To solve that, we prefer to use timestamp comparison.
e.g. : On 5 Dec. 2021, the alarm limit is 5 Jan. 2022 (+31 days)
On 31 Jan 2021, the alarm limit is 28 Feb. 2022 (+28 days)
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-7-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC driver stops the RTCAPB clock during suspend, but the
irq handler from RTC is called before starting clock. Then we are
blocked while accessing RTC registers.
We changes PM callbacks to '_no_irq()' to disable irq during
resume callback and so irq handler will be called after the enable
of RTCAPB clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-6-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Change stm32-rtc driver to not generate an error message when
device probe operation is deferred for a clock.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-5-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The rtc is used to update the stgen counter on wake up from
low power modes, so it needs to be as much accurate as possible.
The maximization of asynchronous divider leads to a 4ms rtc
precision clock.
By decreasing pred_a to 0, it will have pred_s=32767 (when
need_accuracy is true), so stgen clock becomes more accurate
with 30us precision.
Nevertheless this will leads to an increase of power consumption.
Signed-off-by: Christophe Guibout <christophe.guibout@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-4-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
RTC counters are stopped when INIT bit in ISR register is set and
start counting from the (eventual) new value when INIT is reset.
In stm32_rtc_init(), called during probe, the INIT bit is set to
program the prescaler and the 24h mode. This halts the RTC counter
at each probe tentative causing the RTC time to loose from 0.3s to
0.8s at each kernel boot.
If the RTC is battery powered, both prescaler value and 24h mode
are kept during power cycle and there is no need to program them
again.
Check if the desired prescaler value and the 24h mode are already
programmed, then skip reprogramming them to avoid halting the time
counter.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-3-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Date and time are read from two separate RTC registers.
To ensure consistency between the two registers, reading the time
register locks the values in the shadow date register until the
date register is read.
Thus, the whole date/time read requires reading the time register
first, followed by reading the date register.
If the reads are done in reversed order, the shadow date register
will remain locked until a future read operation. The future read
will read the former date value that could be already invalid.
Fix the read order of date/time registers in stm32_rtc_valid_alrm()
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230705174357.353616-2-valentin.caron@foss.st.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for new NXP RTC PCF2131.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230622145800.2442116-18-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF2127/29 do NOT support alarms with a 1 second resolution, but
the PCF2131 does.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-17-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The watchdog value register cannot be read on the PCF2131 after being
set.
Add a new flag to identify which variant has read access to this
register, and use this flag to selectively test if watchdog timer was
started by bootloader.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-16-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Introduce in the configuration structure two new values to hold the
watchdog clock source and the min_hw_heartbeat_ms value.
The minimum and maximum timeout values are automatically computed from
the watchdog clock source value for each variant.
The PCF2131 has no 1Hz watchdog clock source, as is the case for
PCF2127/29.
The next best choice is using a 1/4Hz clock, giving a watchdog timeout
range between 4 and 1016s. By using the same register configuration as
for the PCF2127/29, the 1/4Hz clock source is selected.
Note: the PCF2127 datasheet gives a min/max range between 1 and 255s,
but it should be between 2 and 254s, because the watchdog is triggered
when the timer value reaches 1, not 0.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-15-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The sequence for updating the time/date registers is slightly
different between PCF2127/29 and PCF2131.
For PCF2127/29, during write operations, the time counting
circuits (memory locations 03h through 09h) are automatically blocked.
For PCF2131, time/date registers write access requires setting the
STOP bit and sending the clear prescaler instruction (CPR). STOP then
needs to be released once write operation is completed.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-14-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The PCF2127 and PCF2129 have one output interrupt pin. The PCF2131 has
two, named INT_A and INT_B. The hardware support that any interrupt
source can be routed to either one or both of them.
Force all interrupt sources to go to the INT A pin.
Support to route any interrupt source to INT A/B pins is not supported
by this driver at the moment.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-13-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This RTC is very similar in functionality to the PCF2127/29.
Basically it:
-supports two new control registers at offsets 4 and 5
-supports a new reset register (not implemented in this driver)
-supports 4 tamper detection functions instead of 1
-has no nvmem (like the PCF2129)
-has two output interrupt pins
Because of that, most of the register addresses are very different,
although they still follow the same layout. For example, the tamper
registers have a different base address, but the offsets are all the same.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-12-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-10-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Tested-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-9-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-8-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will simplify the implementation of new variants into this driver.
Some variants (PCF2131) have a 100th seconds register. This register is
currently not supported in this driver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-7-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Create variant-specific configuration structures to simplify the
implementation of new variants into this driver. It will also avoid
to have too many tests for a specific variant, or a list of variants
for new devices, inside the code itself.
Add configuration options for the support of the NVMEM, bit CD0 in
register WD_CTL as well as the maximum number of registers for each
variant, instead of hardcoding the variant (PCF2127) inside the
i2c_device_id and spi_device_id structures.
Also specify a different maximum number of registers (max_register)
for the PCF2129.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-6-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reading the 7 timetamp registers currently involves reading 25 registers
solely to be able to print the content of the three control registers,
in addition to the 7 timestamp registers. This print never occurs,
unless the user enables dynamic debug in this driver or set
CONFIG_RTC_DEBUG.
Reading the timestamp registers should consist of reading 7
consecutive timestamp registers.
This patch optimize the performance of reading the timestamp registers
by reading 7 consecutive registers instead of 25, and dropping the
print of the control registers.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-3-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Improve performance and readability of rtc_read_time() by reading only
the 7 time registers, instead of reading 8 registers (additional CTRL3
register).
We drop reading of CTRL3 to monitor the low battery flag, as this
check is already available in the ioctl. Anyway, this check only
display an info message and has no other impacts.
The code readability also improves as we do not have to fiddle with
buffer pointer and size arithmetic.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230622145800.2442116-2-hugo@hugovil.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc848 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- swiotlb area sizing fixes (Petr Tesarik)
-----BEGIN PGP SIGNATURE-----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=4Lfc
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
boot reordering work
-----BEGIN PGP SIGNATURE-----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=RZFV
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
On shutdown or kexec, the kernel tries to park the non-boot CPUs with an
INIT IPI. But the same code path is also used by the crash utility. If the
CPU which panics is not the boot CPU then it sends an INIT IPI to the boot
CPU which resets the machine. Prevent this by validating that the CPU which
runs the stop mechanism is the boot CPU. If not, leave the other CPUs in
HLT.
-----BEGIN PGP SIGNATURE-----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=DOCF
-----END PGP SIGNATURE-----
Merge tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
* Fix an uninitialized variable warning.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZKjUjwAKCRBKO3ySh0YR
pn92AQC4gY9GOyKcc/aiAd/t1u8gGxnFtcN06xh4TdVArMM4/AD/UtEKx9LYuaSF
pyhw5SfzxI555HfXkA8ci/D+BxguVQs=
=/vX1
-----END PGP SIGNATURE-----
Merge tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"Nothing exciting here, just getting rid of a gcc warning that I got
tired of seeing when I turn on gcov"
* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix uninit warning in xfs_growfs_data
-----BEGIN PGP SIGNATURE-----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=F8D0
-----END PGP SIGNATURE-----
Merge tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix potential use after free in unmount
- minor cleanup
- add worker to cleanup stale directory leases
* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add a laundromat thread for cached directories
smb: client: remove redundant pointer 'server'
cifs: fix session state transition to avoid use-after-free issue
Lockdep is certainly right to complain about
(&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f
but task is already holding lock:
(&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db
Invert those to the usual ordering.
Fixes: 33313a747e ("mm: lock newly mapped VMA which can be modified after it becomes visible")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZKmgXAAKCRDdBJ7gKXxA
joqDAP0V520Jy0cyJrRMvaQRFMqtVeDOdTpAue7ZOQHSi/LZnAD9EEAxDpYF/V4x
PO27ixXQ4Glm2iYgH7bDX7J73WiA3wg=
=JsYW
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"16 hotfixes. Six are cc:stable and the remainder address post-6.4
issues"
The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.
* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib: dhry: fix sleeping allocations inside non-preemptable section
kasan, slub: fix HW_TAGS zeroing with slub_debug
kasan: fix type cast in memory_is_poisoned_n
mailmap: add entries for Heiko Stuebner
mailmap: update manpage link
bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
MAINTAINERS: add linux-next info
mailmap: add Markus Schneider-Pargmann
writeback: account the number of pages written back
mm: call arch_swap_restore() from do_swap_page()
squashfs: fix cache race with migration
mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
docs: update ocfs2-devel mailing list address
MAINTAINERS: update ocfs2-devel mailing list address
mm: disable CONFIG_PER_VMA_LOCK until its fixed
fork: lock VMAs of the parent process when forking
