There's no need to disable the rng in ingenic_trng_remove.
The driver's init function sets the CFG_GEN_EN bit to enable the
rng. The cleanup function clears CFG_GEN_EN to revert this.
The remove function calls hwrng_unregister. If the ingenic-trng is not
the current rng at this point, CFG_GEN_EN has already been cleared. If
the ingenic-trng is the current rng, drop_current_rng will call the
cleanup function.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use dev_err_probe in error paths to make the code a bit shorter.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get_enabled in the ingenic-trng driver. We don't have to
disable and unprepare the clock any more in error paths or in the remove
function.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Don't assign a value to ret if we're about to return from the probe
function and ret's value is not used.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove two defines which are not used in the ingenic-trng driver's code.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable compile testing for the ingenic-trng driver.
Remove the dependency on HW_RANDOM. The ingenic-trng config section is
under "if HW_RANDOM".
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jakub Kicinski says:
====================
net: page_pool: remove page_pool_release_page()
page_pool_return_page() is a historic artefact from before
recycling of pages attached to skbs was supported. Theoretical
uses for it may be thought up but in practice all existing
users can be converted to use skb_mark_for_recycle() instead.
This code was previously posted as part of the memory provider RFC.
https://lore.kernel.org/all/20230707183935.997267-1-kuba@kernel.org/
====================
Link: https://lore.kernel.org/r/20230720010409.1967072-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that page_pool_release_page() is not exported we can
merge it with page_pool_return_page(). I believe that
the "Do not replace this with page_pool_return_page()"
comment was there in case page_pool_return_page() was
not inlined, to avoid two function calls.
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Link: https://lore.kernel.org/r/20230720010409.1967072-5-kuba@kernel.org
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There seems to be no user calling page_pool_release_page()
for legit reasons, all the users simply haven't been converted
to skb-based recycling, yet. Previous changes converted them.
Update the docs, and unexport the function.
Link: https://lore.kernel.org/r/20230720010409.1967072-4-kuba@kernel.org
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac removes pages from the page pool after attaching them
to skbs. Use page recycling instead.
skb heads are always copied, and pages are always from page
pool in this driver. We could as well mark all allocated skbs
for recycling.
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Link: https://lore.kernel.org/r/20230720010409.1967072-3-kuba@kernel.org
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tsnep builds an skb with napi_build_skb() and then calls
page_pool_release_page() for the page in which that skb's
head sits. Use recycling instead, recycling of heads works
just fine.
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Link: https://lore.kernel.org/r/20230720010409.1967072-2-kuba@kernel.org
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, if cmd in the split ops array is of lower value than the
previous one, genl_validate_ops() continues to do the checks as if
the values are equal. This may result in non-obvious WARN_ON() hit in
these check.
Instead, check the incorrect ordering explicitly and put a WARN_ON()
in case it is broken.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230720111354.562242-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus seems to like the MAINTAINERS file sorted, see
c192ac7357 ("MAINTAINERS 2: Electric Boogaloo").
Since this is currently not the case, restore the sort order.
Fixes: 3abf3d15ff ("MAINTAINERS: ASP 2.0 Ethernet driver maintainers")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230720151107.679668-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 3a3b7ce933 ("CRED: Allow kernel services to override LSM settings for task actions")
this is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 3a3b7ce933 ("CRED: Allow kernel services to override LSM settings for task actions")
[PM: subject tweak, fixes tag]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Change target `make htmldocs` to combine RST Sphinx and the generation of
Rust documentation, when support is available and .config exists.
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Carlos Bilbao <carlos.bilbao@amd.com>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230718151534.4067460-3-carlos.bilbao@amd.com
Generate rustdoc documentation with the rest of subsystem's documentation
in Documentation/output. Add a cross reference to the generated rustdoc in
Documentation/rust/index.rst if Sphinx target rustdoc is set.
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Carlos Bilbao <carlos.bilbao@amd.com>
Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230718151534.4067460-2-carlos.bilbao@amd.com
Move 'panic_print' to its correct place in alphabetical order.
Add parameter format for 'pause_on_oops'.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230715034811.9665-1-rdunlap@infradead.org
Put the arm64 kernel-parameters entries into alphabetical order.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230715235105.17966-1-rdunlap@infradead.org
Use colon to separate parameter name from their specific meaning.
silence the warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_vm_pt.c:793: warning: Function parameter or member 'adev' not described in 'amdgpu_vm_pte_update_noretry_flags'
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the second call to amdgpu_bo_create_kernel() fails, the memory
allocated from the first call should be cleared. If the third call
fails, the memory from the second call should be cleared.
Fixes: b95b539168 ("drm/amdgpu/psp: move PSP memory alloc from hw_init to sw_init")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An instance of for_each_inst() was not changed to match its new
behaviour and is causing a loop.
v2: remove tmp_mask variable
Fixes: b579ea632f ("drm/amdgpu: Modify for_each_inst macro")
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XCP_CTL register is expected to be programmed by firmware. Under certain
conditions FW may not have programmed it correctly. As a workaround,
program it when FW has not programmed the right values.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the list of devices that require the cwsr trap handling
workaround for debugging use cases.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Acked-by: Ruili Ji <ruili.ji@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang on RISC-V appears to be unaffected by the bug causing excessive
stack usage in calculate_bandwidth(). clang 16 with -fstack-usage
reports a 304 byte stack frame size with CONFIG_ARCH_RV32I, and 512
bytes with CONFIG_ARCH_RV64I.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Internal subvp state is not referenced in driver code, so it can be removed.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following checkpatch.pl:
WARNING: printk() should include KERN_<LEVEL> facility level
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch will enable secure decode playback on VCN4_0_2
Signed-off-by: sguttula <Suresh.Guttula@amd.com>
Reviewed-by: Leo Liu <leo.liiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The VBIOS part number is read both in amdgpu_atom_parse() as well
as in atom_get_vbios_pn() and stored twice in the `struct atom_context`
structure. Remove the first unnecessary read and move the `pr_info`
line from that read into the second.
v2: squash in unused variable removal
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The literal blocks in this file lacked the necessary blank line at the top,
causing Sphinx to complain:
/Documentation/ABI/testing/sysfs-bus-nvdimm:11: WARNING: Unexpected indentation.
Add the lines it's longing for and bring about a bit of warning peace.
Reported-by: Hu Haowen <src.res.211@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Gather Data Sampling (GDS) is a transient execution attack using
gather instructions from the AVX2 and AVX512 extensions. This attack
allows malicious code to infer data that was previously stored in
vector registers. Systems that are not vulnerable to GDS will set the
GDS_NO bit of the IA32_ARCH_CAPABILITIES MSR. This is useful for VM
guests that may think they are on vulnerable systems that are, in
fact, not affected. Guests that are running on affected hosts where
the mitigation is enabled are protected as if they were running
on an unaffected system.
On all hosts that are not affected or that are mitigated, set the
GDS_NO bit.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Gather Data Sampling (GDS) is mitigated in microcode. However, on
systems that haven't received the updated microcode, disabling AVX
can act as a mitigation. Add a Kconfig option that uses the microcode
mitigation if available and disables AVX otherwise. Setting this
option has no effect on systems not affected by GDS. This is the
equivalent of setting gather_data_sampling=force.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
The Gather Data Sampling (GDS) vulnerability allows malicious software
to infer stale data previously stored in vector registers. This may
include sensitive data such as cryptographic keys. GDS is mitigated in
microcode, and systems with up-to-date microcode are protected by
default. However, any affected system that is running with older
microcode will still be vulnerable to GDS attacks.
Since the gather instructions used by the attacker are part of the
AVX2 and AVX512 extensions, disabling these extensions prevents gather
instructions from being executed, thereby mitigating the system from
GDS. Disabling AVX2 is sufficient, but we don't have the granularity
to do this. The XCR0[2] disables AVX, with no option to just disable
AVX2.
Add a kernel parameter gather_data_sampling=force that will enable the
microcode mitigation if available, otherwise it will disable AVX on
affected systems.
This option will be ignored if cmdline mitigations=off.
This is a *big* hammer. It is known to break buggy userspace that
uses incomplete, buggy AVX enumeration. Unfortunately, such userspace
does exist in the wild:
https://www.mail-archive.com/bug-coreutils@gnu.org/msg33046.html
[ dhansen: add some more ominous warnings about disabling AVX ]
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Since commit 743210386c ("cgroup: use cgrp->kn->id as the cgroup ID"),
cgrp is associated with its kernfs_node. Update corresponding comment.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We appear to have a gap in our process docs. We go into detail
on how to contribute code to the kernel, and how to be a subsystem
maintainer. I can't find any docs directed towards the thousands
of small scale maintainers, like folks maintaining a single driver
or a single network protocol.
Document our expectations and best practices. I'm hoping this doc
will be particularly useful to set expectations with HW vendors.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230719183225.1827100-1-kuba@kernel.org
Commit 0795e7c031 ("[AFS]: Update the AFS fs documentation.") adds a new
section listing the build configuration options that need to be enabled for
the AFS file system.
The documentation refers to CONFIG_AFS, but the option is called
CONFIG_AFS_FS, since the beginning of Linux's git history.
Refer to the config option with the correct name.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230720094301.9888-1-lukas.bulwahn@gmail.com
Due to some reasons the current mailing list will be revoked and new one
will replace it in the future, hence remove the entry from MAINTAINERS
ahead of time.
Signed-off-by: Hu Haowen <src.res.211@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20230720141846.1787-1-src.res.211@gmail.com
The documentation is not clear about how this delay works.
Empirical tests have shown that with a VSDELAY of 0, the first
scanline is not properly formatted in the output stream when
DSI->DP mode is used. The calculation spreadsheets from Toshiba
seem to always make this value equal to the HFP + 10 for DSI->DP
use-case. For DSI->DPI this value should be > 2 and for DPI->DP
it seems to always be 0x64.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-2-l.stach@pengutronix.de
The PLL often fails to lock with this delay. The new value was
determined by trial and error increasing the delay bit by bit
until the error did not occurr anymore even after several tries.
Then double that value was taken as the minimum delay to be safe.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-1-l.stach@pengutronix.de
Problem:
The max_loop parameter is used for 2 different purposes:
1) initial number of loop devices to pre-create on init
2) maximum number of loop devices to add on access/open()
Historically, its default value (zero) caused 1) to create non-zero
number of devices (CONFIG_BLK_DEV_LOOP_MIN_COUNT), and no hard limit on
2) to add devices with autoloading.
However, the default value changed in commit 85c5019771 ("loop: Fix
the max_loop commandline argument treatment when it is set to 0") to
CONFIG_BLK_DEV_LOOP_MIN_COUNT, for max_loop=0 not to pre-create devices.
That does improve 1), but unfortunately it breaks 2), as the default
behavior changed from no-limit to hard-limit.
Example:
For example, this userspace code broke for N >= CONFIG, if the user
relied on the default value 0 for max_loop:
mknod("/dev/loopN");
open("/dev/loopN"); // now fails with ENXIO
Though affected users may "fix" it with (loop.)max_loop=0, this means to
require a kernel parameter change on stable kernel update (that commit
Fixes: an old commit in stable).
Solution:
The original semantics for the default value in 2) can be applied if the
parameter is not set (ie, default behavior).
This still keeps the intended function in 1) and 2) if set, and that
commit's intended improvement in 1) if max_loop=0.
Before 85c5019771:
- default: 1) CONFIG devices 2) no limit
- max_loop=0: 1) CONFIG devices 2) no limit
- max_loop=X: 1) X devices 2) X limit
After 85c5019771:
- default: 1) CONFIG devices 2) CONFIG limit (*)
- max_loop=0: 1) 0 devices (*) 2) no limit
- max_loop=X: 1) X devices 2) X limit
This commit:
- default: 1) CONFIG devices 2) no limit (*)
- max_loop=0: 1) 0 devices 2) no limit
- max_loop=X: 1) X devices 2) X limit
Future:
The issue/regression from that commit only affects code under the
CONFIG_BLOCK_LEGACY_AUTOLOAD deprecation guard, thus the fix too is
contained under it.
Once that deprecated functionality/code is removed, the purpose 2) of
max_loop (hard limit) is no longer in use, so the module parameter
description can be changed then.
Tests:
Linux 6.4-rc7
CONFIG_BLK_DEV_LOOP_MIN_COUNT=8
CONFIG_BLOCK_LEGACY_AUTOLOAD=y
- default (original)
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
open: /dev/loop8: No such device or address
- default (patched)
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
#
- max_loop=0 (original & patched):
# ls -1 /dev/loop*
/dev/loop-control
# ./test-loop
#
- max_loop=8 (original & patched):
# ls -1 /dev/loop*
/dev/loop-control
/dev/loop0
...
/dev/loop7
# ./test-loop
open: /dev/loop8: No such device or address
- max_loop=0 (patched; CONFIG_BLOCK_LEGACY_AUTOLOAD is not set)
# ls -1 /dev/loop*
/dev/loop-control
# ./test-loop
open: /dev/loop8: No such device or address
Fixes: 85c5019771 ("loop: Fix the max_loop commandline argument treatment when it is set to 0")
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230720143033.841001-3-mfo@canonical.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'probe' callback in __register_blkdev() is only used under the
CONFIG_BLOCK_LEGACY_AUTOLOAD deprecation guard.
The loop_probe() function is only used for that callback, so guard it
too, accordingly.
See commit fbdee71bb5 ("block: deprecate autoloading based on dev_t").
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230720143033.841001-2-mfo@canonical.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
User applications alert the driver when the Doorbell FIFO
reaches the alarm threshold. The driver updates the pacing
parameters in the shared page to do the maximum pacing
by the application till the DB FIFO congestion reduces to
pacing threshold. Driver keeps checking the DB FIFO depth
at the pacing interval and gradually adjusts the pacing level.
Once the pacing level reaches default values (no congestion in
the FIFO) pacing gets completed.
Link: https://lore.kernel.org/r/1689742977-9128-7-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Update the alloc_page uapi functionality for handling the
mapping of doorbell pacing shared page and bar address.
Link: https://lore.kernel.org/r/1689742977-9128-6-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Chandramohan Akula <chandramohan.akula@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
