When waiting for a port to get active/idle there is no point in the
complexity of specifying an exact timeout and for that the suitable wait
API instead of just using the maximum timeout. The sequence in
particular is not performance critical at all either and due to
scheduling it's not guaranteed anyhow how long the wait will last at the
given timescale. In the usual case where the wait succeeds the actual
time waited does not change with the increased timeout.
Simplify things accordingly, describing the bspec platform specific
timeouts in code comments.
v2: Clarify the rationale in the commit log. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-8-imre.deak@intel.com
A port can be disabled only via a modeset (or during HW state
sanitization) when the port is enabled. Thus it's not required to check
the port's enabled state before disabling it. In any case if the port
happened to be disabled, the following disabling would be just a nop and
waiting for the buffer's idle state should succeed. Simplify the
disabling sequence accordingly.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-7-imre.deak@intel.com
In the past intel_digital_port::dp.prepare_link_retrain() could be
called directly (vs. from a modeset) to retrain an enabled link. In that
case the port had to be first disabled and then re-enabled. That changed
with commit 2885d283cc ("drm/i915/dp: Retrain SST links via a modeset
commit"), after which the only way prepare_link_retrain() can be called
is from a modeset during link training when the port is still disabled.
Simplify things accordingly, assuming the disabled port state.
v2: Don't use drm_i915_private in intel_ddi_prepare_link_retrain(). (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-6-imre.deak@intel.com
Add the missing PHY lane stagger delay programming for ICL-ADL
platforms on TypeC DP outputs.
v2: (Jani)
- Clarify code comment about lane stagger programming.
- Robustify macro calls with parens.
Bspec: 7534, 49533
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-5-imre.deak@intel.com
Make the PORT_WIDTH macro of the XELPDP_PORT_CTL1 register work the same
way as those used for the DDI_BUF_CTL and the TRANS_DDI_FUNC_CTL
registers: accept a width parameter and convert it to the given
register's encoding.
v2: Robustify macro calls with parens. (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-4-imre.deak@intel.com
Fix the port width programming in the DDI_BUF_CTL register on MTLP+,
where this had an off-by-one error.
Cc: <stable@vger.kernel.org> # v6.5+
Fixes: b66a8abaa4 ("drm/i915/display/mtl: Fill port width in DDI_BUF_/TRANS_DDI_FUNC_/PORT_BUF_CTL for HDMI")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-3-imre.deak@intel.com
The format of the port width field in the DDI_BUF_CTL and the
TRANS_DDI_FUNC_CTL registers are different starting with MTL, where the
x3 lane mode for HDMI FRL has a different encoding in the two registers.
To account for this use the TRANS_DDI_FUNC_CTL's own port width macro.
Cc: <stable@vger.kernel.org> # v6.5+
Fixes: b66a8abaa4 ("drm/i915/display/mtl: Fill port width in DDI_BUF_/TRANS_DDI_FUNC_/PORT_BUF_CTL for HDMI")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250214142001.552916-2-imre.deak@intel.com
It is generally expected that the write() function should return a
positive value indicating the number of bytes written or a negative
error code if an error occurs. Returning 0 is unusual and can lead
to unexpected behavior.
When the user program writes the same value to wedged_mode twice in
a row, a lockup will occur, because the value expected to be
returned by the write() function inside the program should be equal
to the actual written value instead of 0.
To reproduce the issue:
echo 1 > /sys/kernel/debug/dri/0/wedged_mode
echo 1 > /sys/kernel/debug/dri/0/wedged_mode <- lockup here
Signed-off-by: Xin Wang <x.wang@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Fei Yang <fei.yang@intel.com>
Cc: Shuicheng Lin <shuicheng.lin@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213223615.2327367-1-x.wang@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In case we have to retry the loop, we are missing to unlock+put the
folio. In that case, we will keep failing make_device_exclusive_range()
because we cannot grab the folio lock, and even return from the function
with the folio locked and referenced, effectively never succeeding the
make_device_exclusive_range().
While at it, convert the other unlock+put to use a folio as well.
This was found by code inspection.
Fixes: 8f187163eb ("nouveau/svm: implement atomic SVM access")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Tested-by: Alistair Popple <apopple@nvidia.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250124181524.3584236-2-david@redhat.com
We may have commit which doesn't have any non-arming plane register
writes. In that case there aren't "Frame Change" event before DSB vblank
evasion which hangs as PIPEDSL register is reading as 0 when PSR state is
SRDENT(PSR1) or DEEP_SLEEP(PSR2). Handle this by ensuring "Frame Change"
event at the begin of DSB commit if using PSR/PR.
v3: dsb_commit as a first parameter
v2: use intel_psr_trigger_frame_change_event
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-13-jouni.hogander@intel.com
PIPEDSL is reading as 0 when in SRDENT(PSR1) or DEEP_SLEEP(PSR2). On
wake-up scanline counting starts from vblank_start - 1. We don't know if
wake-up is already ongoing when evasion starts. In worst case PIPEDSL could
start reading valid value right after checking the scanline. In this
scenario we wouldn't have enough time to write all registers. To tackle
this evade scanline 0 as well. As a drawback we have 1 frame delay in flip
when waking up.
v2:
- use intel_dsb_emit_wait_dsl
- add evasion of scanline 0 also for Panel Replay
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-11-jouni.hogander@intel.com
We have different approach on how flip is considered being complete. We are
waiting for vblank on DSB and generate interrupt when it happens and this
interrupt is considered as indication of completion -> we definitely do not
want to skip vblank wait.
Also not skipping scanline wait shouldn't cause any problems if we are in
DEEP_SLEEP PIPEDSL register is returning 0 -> evasion does nothing and if
we are not in DEEP_SLEEP evasion works same way as without PSR.
v2: add comment explaining why we are not setting DSB_SKIP_WAITS_EN
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-10-jouni.hogander@intel.com
- Carve out wopcm portion from the stolen memory (Nirmoy)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmeuKuwACgkQ+mJfZA7r
E8otWAf9EYDbWE9va00T9kzPbzs3h/LEgkF7E22zgQPDcty+EwP+yGC9itcYnW8x
HfzR7iQa56Q3iO9i+UINkjZnVzjNtuQpM5G4vKKW6eBwO/4tGvXy2knBf5Vd2yvY
nLZQRPitaScwV17VjL0iw4ib4WuQWpJU7FZeTlIz8oHsF4dDV2B/R5k4REvbzM8a
81O0bXT+gvTQ//6A0PWDe4zPkS2dxKk6lhw57WRAnk0q4zRfV2rr4zlUHOrvDu8H
Lfzz+fkrssYNVvzstLesRlIr8za6IhJDg4crro57dnAluNbPBCGl+GHBAc4eVeC5
P6z7Hl1xfkLGrFJoTj6m9Lvywt9Osw==
=YbHU
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-fixes-2025-02-13' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
- Remove bo->clients out of bos_lock area (Tejas)
- Carve out wopcm portion from the stolen memory (Nirmoy)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Z64rCicgpBe_t5GY@intel.com
amdgpu:
- Fix shutdown regression on old APUs
- Fix compute queue hang on gfx9 APUs
- Fix possible invalid access in PSP failure path
- Avoid possible buffer overflow in pptable override
amdkfd:
- Properly free gang bo in failure path
- GFX12 trap handler fix
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQgO5Idg2tXNTSZAr293/aFa7yZ2AUCZ64QYgAKCRC93/aFa7yZ
2E4uAPoCIug8zq4eyn2FIke05YUsKIleaWqnyfx5lOxE0liX6AEAqVjST+WNWmjx
6vC1MAOUitiVjOjLcsGIHG+xXK2T0Ak=
=H/SZ
-----END PGP SIGNATURE-----
Merge tag 'amd-drm-fixes-6.14-2025-02-13' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.14-2025-02-13:
amdgpu:
- Fix shutdown regression on old APUs
- Fix compute queue hang on gfx9 APUs
- Fix possible invalid access in PSP failure path
- Avoid possible buffer overflow in pptable override
amdkfd:
- Properly free gang bo in failure path
- GFX12 trap handler fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213153843.242640-1-alexander.deucher@amd.com
mutex fix for host1x, an unitialized variable fix for panthor, and a
config selection fix for hibmc.
-----BEGIN PGP SIGNATURE-----
iJUEABMJAB0WIQTkHFbLp4ejekA/qfgnX84Zoj2+dgUCZ64QCQAKCRAnX84Zoj2+
dmDKAYDbYyoPwDUEHDK87HiVKov0rVgeZ5Bxol+AV+5SP57XBSFP3p+IgtnWxZhQ
5f6yAl4BgKI70F7x4EQEyuOejEVAVCZTHuA9lzWcYIDkUQmvcIoY8t0HY9gZpW42
ZKrhAX3/vg==
=JF2k
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2025-02-13' of https://gitlab.freedesktop.org/drm/misc/kernel into drm-fixes
Some locking fixes for the HDMI infrastructure tests, an unitialized
mutex fix for host1x, an unitialized variable fix for panthor, and a
config selection fix for hibmc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213-brilliant-terrier-from-hell-d06dd5@houat
amdgpu can handle async flips on overlay planes, so allow it for atomic
async checks.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250127-tonyk-async_flip-v12-2-0f7f8a8610d3@igalia.com
[DB: fixed checkpatch warning by adding braces]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, DRM atomic uAPI allows only primary planes to be flipped
asynchronously. However, each driver might be able to perform async
flips in other different plane types. To enable drivers to set their own
restrictions on which type of plane they can or cannot flip, use the
existing atomic_async_check() from struct drm_plane_helper_funcs to
enhance this flexibility, thus allowing different plane types to be able
to do async flips as well.
Create a new parameter for the atomic_async_check(), `bool flip`. This
parameter is used to distinguish when this function is being called from
a plane update from a full page flip.
In order to prevent regressions and such, we keep the current policy: we
skip the driver check for the primary plane, because it is always
allowed to do async flips on it.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Christopher Snowhill <chris@kode54.net>
Tested-by: Christopher Snowhill <chris@kode54.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20250127-tonyk-async_flip-v12-1-0f7f8a8610d3@igalia.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This function will synchronously cancel and wait for many display
work queue items, which might try to take the runtime pm reference
causing a bad deadlock. So, remove it from the runtime_pm suspend patch.
Reported-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212192447.402715-1-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
spin_lock/unlock() functions used in interrupt contexts could
result in a deadlock, as seen in GitLab issue #13399,
which occurs when interrupt comes in while holding a lock.
Try to remedy the problem by saving irq state before spin lock
acquisition.
v2: add irqs' state save/restore calls to all locks/unlocks in
signal_irq_work() execution (Maciej)
v3: use with spin_lock_irqsave() in guc_lrc_desc_unpin() instead
of other lock/unlock calls and add Fixes and Cc tags (Tvrtko);
change title and commit message
Fixes: 2f2cc53b5f ("drm/i915/guc: Close deregister-context race against CT-loss")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13399
Signed-off-by: Krzysztof Karas <krzysztof.karas@intel.com>
Cc: <stable@vger.kernel.org> # v6.9+
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/pusppq5ybyszau2oocboj3mtj5x574gwij323jlclm5zxvimmu@mnfg6odxbpsv
Use DRM's device wedged event to notify userspace that a reset had
happened. For now, only use `none` method meant for telemetry
capture.
In the future we might want to report a recovery method if the reset didn't
succeed.
Acked-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204070528.1919158-6-raag.jadav@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Now that we have device wedged event provided by DRM core, make use
of it and support both driver rebind and bus-reset based recovery.
With this in place, userspace will be notified of wedged device on
gt reset failure.
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Aravind Iddamsetty <aravind.iddamsetty@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204070528.1919158-5-raag.jadav@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This was previously attempted as xe specific reset uevent but dropped
in commit 77a0d4d1ce ("drm/xe/uapi: Remove reset uevent for now")
as part of refactoring.
Now that we have device wedged event provided by DRM core, make use
of it and support both driver rebind and bus-reset based recovery.
With this in place userspace will be notified of wedged device, on
the basis of which, userspace may take respective action to recover
the device.
$ udevadm monitor --property --kernel
monitor will print the received events for:
KERNEL - the kernel uevent
KERNEL[265.802982] change /devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0 (drm)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:01.0/0000:01:00.0/0000:02:01.0/0000:03:00.0/drm/card0
SUBSYSTEM=drm
WEDGED=rebind,bus-reset
DEVNAME=/dev/dri/card0
DEVTYPE=drm_minor
SEQNUM=5208
MAJOR=226
MINOR=0
v2: Change authorship to Himal (Aravind)
Add uevent for all device wedged cases (Aravind)
v3: Generic implementation in DRM subsystem (Lucas)
v4: Change authorship to Raag (Aravind)
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: Aravind Iddamsetty <aravind.iddamsetty@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204070528.1919158-4-raag.jadav@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Introduce device wedged event, which notifies userspace of 'wedged'
(hanged/unusable) state of the DRM device through a uevent. This is
useful especially in cases where the device is no longer operating as
expected and has become unrecoverable from driver context. Purpose of
this implementation is to provide drivers a generic way to recover the
device with the help of userspace intervention without taking any drastic
measures (like resetting or re-enumerating the full bus, on which the
underlying physical device is sitting) in the driver.
A 'wedged' device is basically a device that is declared dead by the
driver after exhausting all possible attempts to recover it from driver
context. The uevent is the notification that is sent to userspace along
with a hint about what could possibly be attempted to recover the device
from userspace and bring it back to usable state. Different drivers may
have different ideas of a 'wedged' device depending on hardware
implementation of the underlying physical device, and hence the vendor
agnostic nature of the event. It is up to the drivers to decide when they
see the need for device recovery and how they want to recover from the
available methods.
Driver prerequisites
--------------------
The driver, before opting for recovery, needs to make sure that the
'wedged' device doesn't harm the system as a whole by taking care of the
prerequisites. Necessary actions must include disabling DMA to system
memory as well as any communication channels with other devices. Further,
the driver must ensure that all dma_fences are signalled and any device
state that the core kernel might depend on is cleaned up. All existing
mmaps should be invalidated and page faults should be redirected to a
dummy page. Once the event is sent, the device must be kept in 'wedged'
state until the recovery is performed. New accesses to the device
(IOCTLs) should be rejected, preferably with an error code that resembles
the type of failure the device has encountered. This will signify the
reason for wedging, which can be reported to the application if needed.
Recovery
--------
Current implementation defines three recovery methods, out of which,
drivers can use any one, multiple or none. Method(s) of choice will be
sent in the uevent environment as ``WEDGED=<method1>[,..,<methodN>]`` in
order of less to more side-effects. If driver is unsure about recovery
or method is unknown (like soft/hard system reboot, firmware flashing,
physical device replacement or any other procedure which can't be
attempted on the fly), ``WEDGED=unknown`` will be sent instead.
Userspace consumers can parse this event and attempt recovery as per the
following expectations.
=============== ========================================
Recovery method Consumer expectations
=============== ========================================
none optional telemetry collection
rebind unbind + bind driver
bus-reset unbind + bus reset/re-enumeration + bind
unknown consumer policy
=============== ========================================
The only exception to this is ``WEDGED=none``, which signifies that the
device was temporarily 'wedged' at some point but was recovered from driver
context using device specific methods like reset. No explicit recovery is
expected from the consumer in this case, but it can still take additional
steps like gathering telemetry information (devcoredump, syslog). This is
useful because the first hang is usually the most critical one which can
result in consequential hangs or complete wedging.
Consumer prerequisites
----------------------
It is the responsibility of the consumer to make sure that the device or
its resources are not in use by any process before attempting recovery.
With IOCTLs erroring out, all device memory should be unmapped and file
descriptors should be closed to prevent leaks or undefined behaviour. The
idea here is to clear the device of all user context beforehand and set
the stage for a clean recovery.
Example
-------
Udev rule::
SUBSYSTEM=="drm", ENV{WEDGED}=="rebind", DEVPATH=="*/drm/card[0-9]",
RUN+="/path/to/rebind.sh $env{DEVPATH}"
Recovery script::
#!/bin/sh
DEVPATH=$(readlink -f /sys/$1/device)
DEVICE=$(basename $DEVPATH)
DRIVER=$(readlink -f $DEVPATH/driver)
echo -n $DEVICE > $DRIVER/unbind
echo -n $DEVICE > $DRIVER/bind
Customization
-------------
Although basic recovery is possible with a simple script, consumers can
define custom policies around recovery. For example, if the driver supports
multiple recovery methods, consumers can opt for the suitable one depending
on scenarios like repeat offences or vendor specific failures. Consumers
can also choose to have the device available for debugging or telemetry
collection and base their recovery decision on the findings. This is useful
especially when the driver is unsure about recovery or method is unknown.
v4: s/drm_dev_wedged/drm_dev_wedged_event
Use drm_info() (Jani)
Kernel doc adjustment (Aravind)
v5: Send recovery method with uevent (Lina)
v6: Access wedge_recovery_opts[] using helper function (Jani)
Use snprintf() (Jani)
v7: Convert recovery helpers into regular functions (Andy, Jani)
Aesthetic adjustments (Andy)
Handle invalid recovery method
v8: Allow sending multiple methods with uevent (Lucas, Michal)
static_assert() globally (Andy)
v9: Provide 'none' method for device reset (Christian)
Provide recovery opts using switch cases
v11: Log device reset (André)
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204070528.1919158-2-raag.jadav@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In jadard_prepare() a reset pulse is generated with the following
statements (delays ommited for clarity):
gpiod_set_value(jadard->reset, 1); --> Deassert reset
gpiod_set_value(jadard->reset, 0); --> Assert reset for 10ms
gpiod_set_value(jadard->reset, 1); --> Deassert reset
However, specifying second argument of "0" to gpiod_set_value() means to
deassert the GPIO, and "1" means to assert it. If the reset signal is
defined as GPIO_ACTIVE_LOW in the DTS, the above statements will
incorrectly generate the reset pulse (inverted) and leave it asserted
(LOW) at the end of jadard_prepare().
Fix reset behavior by inverting gpiod_set_value() second argument
in jadard_prepare(). Also modify second argument to devm_gpiod_get()
in jadard_dsi_probe() to assert the reset when probing.
Do not modify it in jadard_unprepare() as it is already properly
asserted with "1", which seems to be the intended behavior.
Fixes: 6b818c533d ("drm: panel: Add Jadard JD9365DA-H3 DSI panel")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240927135306.857617-1-hugo@hugovil.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240927135306.857617-1-hugo@hugovil.com
In some cases observed during ESD tests, the TI SN65DSI83 cannot recover
from errors by itself. A full restart of the bridge is needed in those
cases to have the bridge output LVDS signals again.
Also, during tests, cases were observed where reading the status of the
bridge was not even possible. Indeed, in those cases, the bridge stops
to acknowledge I2C transactions. Only a full reset of the bridge (power
off/on) brings back the bridge to a functional state.
The TI SN65DSI83 has some error detection capabilities. Introduce an
error recovery mechanism based on this detection.
The errors detected are signaled through an interrupt. On system where
this interrupt is not available, the driver uses a polling monitoring
fallback to check for errors. When an error is present or when reading
the bridge status leads to an I2C failure, the recovery process is
launched.
Restarting the bridge needs to redo the initialization sequence. This
initialization sequence has to be done with the DSI data lanes driven in
LP11 state. In order to do that, the recovery process resets the whole
output path (i.e the path from the encoder to the connector) where the
bridge is located.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-5-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The current code uses a the reset_pipe() local function to reset the
CRTC outputs.
drm_atomic_helper_reset_crtc() has been introduced recently and it
performs exact same operations.
In order to avoid code duplication, use the new helper instead of the
local function.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-4-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
drm_atomic_helper_reset_crtc() allows to reset the CRTC active outputs.
This resets all active components available between the CRTC and
connectors.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210132620.42263-3-herve.codina@bootlin.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
If the driver initialization fails, the vkms_exit() function might
access an uninitialized or freed default_config pointer and it might
double free it.
Fix both possible errors by initializing default_config only when the
driver initialization succeeded.
Reported-by: Louis Chauvet <louis.chauvet@bootlin.com>
Closes: https://lore.kernel.org/all/Z5uDHcCmAwiTsGte@louis-chauvet-laptop/
Fixes: 2df7af93fd ("drm/vkms: Add vkms_config type")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmremann@suse.de>
Reviewed-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212084912.3196-1-jose.exposito89@gmail.com
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Add PSR2_MAN_TRK_CTL writing into DSB commit in intel_atomic_dsb_finish.
Taking PSR lock over DSB commit is not needed because PSR2_MAN_TRK_CTL is
now written only by DSB.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-8-jouni.hogander@intel.com
Allow writing PSR2_MAN_TRK_CTL using DSB by using intel_de_write_dsb. Do
not check intel_dp->psr.lock being held when using DSB. This assertion
doesn't make sense as in case of using DSB the actual write happens later
and we are not taking intel_dp->psr.lock mutex over dsb commit.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-7-jouni.hogander@intel.com
In LunarLake we have SFF_CTL register which contains SFF bit ored with
respective SFF bit in PSR2_MAN_TRK_CTL register. Use this register instead
of the bit in PSR2_MAN_TRK_CTL on frontbuffer tracking callbacks. This
helps us avoiding taking psr mutex when performing atomic commit.
We don't need to set the CFF bit as selective update configuration in
PSR2_MAN_TRL_CTL is not overwritten anymore. I.e. we have valid
configuration in PSR2_MAN_TRK_CTL and in plane SEL_FETCH_* registers when
SFF bit gets cleared by the HW in case something triggers "frame change"
event after SFF bit is cleared.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-6-jouni.hogander@intel.com
We are preparing for a change where only frontbuffer flush will use
single full frame bit of a new register (SFF_CTL) available on LunarLake
onwards.
It shouldn't be necessary to have SFF bit set if CFF bit is set in
PSR2_MAN_TRK_CTL -> removing setting it on all platforms as there is not
reason to have it different on older platforms.
v2: commit message improved
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250213064804.2077127-2-jouni.hogander@intel.com
This is part of a prandom cleanup, which removes
next_pseudo_random32 and replaces it with the standard PRNG.
Signed-off-by: Markus Theil <theil.markus@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250211063332.16542-2-theil.markus@gmail.com
The drm_writeback_cleanup_job() function frees "pos" so call
list_del(&pos->list_entry) first to avoid a use after free.
Fixes: 1914ba2b91 ("drm: writeback: Create drmm variants for drm_writeback_connector initialization")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78abd541-71e9-4b3b-a05d-2c7caf8d5b2f@stanley.mountain
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Going forward, struct intel_display is the main display device data
pointer. Convert as much as possible of intel_combo_phy.[ch] to struct
intel_display, along with intel_phy_is_combo() in intel_display.c.
Drive-by convert some drm_dbg() to drm_dbg_kms() while at it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c2e0a6294a8eaa4c16632881edc4f2d23c576101.1739378096.git.jani.nikula@intel.com