Use INTC_IRQ_PINS_16H on sh7372 to have two separate
interrupt controllers for the external IRQ pins.
This is preparation work for future IRQ domain support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update mach-shmobile to use 0x3400 as INTCS_VECT_BASE.
Since the ARM architecture a little while back added support
for 10 bit irqs we can now undo the previously merged commit
9b7c23adb3 and use 0x3400 as
INTCS vector base.
This change is necessary to avoid overlapping of interrupt
ranges so separate IRQ domains can be used for different INTC
instances. Without this fix the vectors used by various INTC
instances are overlapping on for instance sh7372 which works
at the moment but breaks upcoming IRQ domain support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add INTC_IRQ_PINS_16H to allow broken out support of the
the high 16 external interrupt pins. On SoCs with 32 external
interrupt pins the interrupt vectors for the low 16 and the
high 16 interrupt pins are sparesly populated. The low 16 are
at 0x0200 and high 16 are at 0x3200 which with current macros
results in a separation of 384 linux interrupts. This sparse
population makes it unsuitable with a single IRQ domain to
cover the full IRQ range, so this macro breaks out the 32 pins
into two separate 16 bit controllers to allow two independent
INTC instances with two separate IRQ domains.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add the function shmobile_setup_delay() to let platforms
configure their maximum loops per jiffy delay. With this
jiffies calculation done the dependency on early timer
is removed.
In the future this allows us to assign timers
using the regular driver model via the device tree.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Derrik Pates reports that an utimensat with a NULL argument results in the
current time being sent from the kernel with 1 second granularity.
Reported-by: Derrik Pates <demon@now.ai>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Wake secondary cpu via resched instead of
"Unknown IPI message 0x1"
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We don't support missing configs at all so segfaulting isn't that bad
but since we've got checks in the code move the dereference after them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Jan Kara removed 'sb->s_dirt' VFS flag references, so we do not need to
register the ext2 'ext2_write_super()' method in the VFS superblock operations,
because 'sb->s_dirt' won't be ever set to 1 and VFS won't ever call
'->write_super()' anyway. Thus, remove the method.
Tested using xfstests.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Places which modify superblock feature / state fields mark the superblock
buffer dirty so it is written out by flusher thread. Thus there's no need to
set s_dirt there.
The only other fields changing in the superblock are the numbers of free
blocks, free inodes and s_wtime. There's no real need to write (or even
compute) these periodically. Free blocks / inodes counters are recomputed on
every mount from group counters anyway and value of s_wtime is only
informational and imprecise anyway. So it should be enough to write these
opportunistically on mount, remount, umount, and sync_fs times.
Signed-off-by: Jan Kara <jack@suse.cz>
Currently on unmount if we are mounted R/W, we first write the superblock to
the media if it is dirty, and then write it again, which is not optimal. This
patch makes ext2 write the superblock on unmount less times.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Commit 00eacd6 ("ext3: make ext3 mount default to barrier=1") changed
the default barrier mount option for ext3. The documentation needs to
be updated, so this patch does that.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
max_debt, involved variables and calculations
are no longer needed, clean them up.
Signed-off-by: Akira Fujita <a-fujita@rs.jp.nec.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently we write out all journal buffers in WRITE_SYNC mode. This improves
performance for fsync heavy workloads but hinders performance when writes
are mostly asynchronous, most noticably it slows down readers and users
complain about slow desktop response etc.
So submit writes as asynchronous in the normal case and only submit writes as
WRITE_SYNC if we detect someone is waiting for current transaction commit.
I've gathered some numbers to back this change. The first is the read latency
test. It measures time to read 1 MB after several seconds of sleeping in
presence of streaming writes.
Top 10 times (out of 90) in us:
Before After
2131586 697473
1709932 557487
1564598 535642
1480462 347573
1478579 323153
1408496 222181
1388960 181273
1329565 181070
1252486 172832
1223265 172278
Average:
619377 82180
So the improvement in both maximum and average latency is massive.
I've measured fsync throughput by:
fs_mark -n 100 -t 1 -s 16384 -d /mnt/fsync/ -S 1 -L 4
in presence of streaming reader. The numbers (fsyncs/s) are:
Before After
9.9 6.3
6.8 6.0
6.3 6.2
5.8 6.1
So fsync performance seems unharmed by this change.
Signed-off-by: Jan Kara <jack@suse.cz>
Fix build warnings by providing a struct stub since no fields of
the struct are used:
include/linux/vgaarb.h:66:9: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:66:9: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/vgaarb.h:99:34: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:109:6: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:121:8: warning: 'struct pci_dev' declared inside parameter list
include/linux/vgaarb.h:140:37: warning: 'struct pci_dev' declared inside parameter list
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit f01ee60fff ("regmap: implement register striding") caused the
compile errors below. Fix them.
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_sync_unlock':
drivers/base/regmap/regmap-irq.c:62:12: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c:62:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_enable':
drivers/base/regmap/regmap-irq.c:77:37: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_disable':
drivers/base/regmap/regmap-irq.c:85:37: error: 'map' undeclared (first use in this function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most code assumes that the pinctrl ops are present. Validate this when
registering a pinctrl driver. Remove the one place in the code that
was checking whether one of these non-optional ops was present.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Macros in <linux/pinctrl/machine.h> call ARRAY_SIZE(), the definition of
which eventually calls BUILD_BUG_ON_ZERO(), which is defined in
<linux/bug.h>. Include that so that every .c file using the pinctrl macros
doesn't have to do that itself.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl_register_mappings is defined in core.c, so change the dependent
macro from CONFIG_MUX to CONFIG_PINCTRL.
The compile error message is:
drivers/pinctrl/core.c:886: error: redefinition of 'pinctrl_register_mappings'
include/linux/pinctrl/machine.h:160: note: previous definition of 'pinctrl_register_mappings' was here
make[2]: *** [drivers/pinctrl/core.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also use CONFIG_PM_SLEEP instead of CONFIG_PM to guard PM methods.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes the irq_domain_mapping debugfs output to pad pointer
values with leading zeros so that pointer values are displayed
correctly. Otherwise you get output similar to "0x 5e0000000000000".
Also, when the irq_domain is set to 'null'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Daney <david.daney@cavium.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Add support for another Medion X10 remote. This was apparently
originally used with the Medion Digitainer box, but is now sold
separately without any Digitainer labeling.
A peculiarity of this remote is a scrollwheel in place of up/down
buttons. Each direction is mapped to 8 different scancodes, each
corresponding to 1..8 notches, allowing multiple notches to the same
direction to be transmitted in a single scancode. The driver transforms
the multi-notch scancodes to multiple events of the single-notch
scancode.
(0x70..0x77 = 1..8 notches down, 0x78..0x7f = 1..8 notches up)
Since the scrollwheel scancodes are the same that are used for mouse on
some other X10 (ati_remote) remotes, the driver will now check whether
the active keymap has a keycode defined for the single-notch scancode
when a mouse/scrollwheel scancode (0x70..0x7f) is received. If set,
scrollwheel is assumed, otherwise mouse is assumed.
This remote ships with a different receiver than the already supported
Medion X10 remote, but they share the same USB ID. The only difference
in the USB descriptors is that the Digitainer receiver has the Remote
Wakeup bit set in bmAttributes of the Configuration Descriptor.
Therefore that is used to select the default keymap.
Thanks to Stephan Raue from OpenELEC (www.openelec.tv) for providing me
both a Medion X10 Digitainer remote+receiver and an already supported
Medion X10 remote+receiver. Thanks to Martin Beyss for providing some
useful information about the remote (including the "Digitainer" name).
This patch has been tested by both of them and myself.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Stephan Raue <stephan@openelec.tv>
Tested-by: Martin Beyss <Martin.Beyss@rwth-aachen.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the ati_remote default keymap is selected directly based on
the USB device id.
Add support for instead specifying a function returning the default
keymap, allowing more complex selection logic to be added when needed.
This will be used for Medion X10 remotes in a following commit.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The actual name of the irq_domain mapping debugfs file is
"irq_domain_mapping" not "virq_mapping".
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It makes no sense to export this trivial function. Make it a static inline
instead.
This patch also drops virq_to_hw from arch/c6x since it is unused by that
architecture.
v2: Move irq_hw_number_t into types.h to fix ARM build failure
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit 4bbdd45a (irq_domain/powerpc: eliminate irq_map; use
irq_alloc_desc() instead) code was added that ignores error returns
from irq_alloc_desc_from() by (silently) casting the return value to
unsigned. The negitive value error return now suddenly looks like a
valid irq number.
Commits cc79ca69 (irq_domain: Move irq_domain code from powerpc to
kernel/irq) and 1bc04f2c (irq_domain: Add support for base irq and
hwirq in legacy mappings) move this code to its current location in
irqdomain.c
The result of all of this is a null pointer dereference OOPS if one of
the error cases is hit.
The fix: Don't cast away the negativeness of the return value and then
check for errors.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: dropped addition of new 'irq' variable]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the future we'll be unifying some of the 32/64 page fault path, so
start to tidy up the _64 one by killing off some of the unused debug
cruft.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)
The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.
Port these changes to the 32-bit SH platform.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The bulk of the MSTP users require 32-bit access, but this isn't the case
for some of the SH-2A parts, so add in some basic infrastructure to let
the CPU define its required access size in preparation.
Requested-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes following compilation warning:
Error: no ID for constraint linkend: v4l2-jpeg-chroma-subsampling.
and adds missing JPEG control class at the Table A.58.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our SMP cache flush ops use CPU cross calls to deal with things
like I-cache accesses not being broadcast in hardware, so ensure that
the CACHE_FLUSH_IS_SAFE reflects this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use the DEFINE_RES_* macros to reduce some of the boilerplate code.
Signed-off-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Commit fe1952fc0a
"powerpc: Rework runlatch code" has a nasty typo
where it uses "TLF_RUNLATCH" instead of "_TLF_RUNLATCH"
(bit number instead of bit mask), causing some flags to
be potentially lost such as _TLF_RESTORE_SIGMASK
(Brown paper bag for me ! We should be able to make
that break at compile time with a bit of magic, any
volunteer ?)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Stanislawski <t.stanislaws@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains code change only to remove redundant
code to set priv->crop_rect.width/height in probe function.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Acked-by: Chris Lalancette <clalancette@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This functions are no longer used from another file,
so they should be declared as static.
Also is it necessary to move some of them before they
are used, since they are no longer header-declared.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is only used in em28xx-input.c so it
makes no sense to have it anywhere but in em28xx-input.c.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moving this helps isolating em28xx_input and will help
converting it into a separate module.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those functions will be needed by em28xx-input module, to be
added on the next patches.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>