When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This field is never set to anything non-zero in
mac80211, so we should be able to remove it.
Unfortunately though, the iwlwifi and iwlegacy
drivers use it for their internal TX status
processing (which shouldn't be using the rate
control API to start with), so add a new field
"status.antenna" for them, at least for now.
In the future, I plan to use the new field to
hold the hardware queue, while the SKB's queue
mapping holds the AC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.
Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently stop the queue when changing the rate
control between 20/40 MHz in the BSS. This seems to
have been necessary when we actually changed the
channel, but now that we just update the station it
doesn't seem right any more. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.
Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.
This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the AC constants instead of hard-coding
the numbers with comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial wrapper function, inline it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason for it to not be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code formatting and also replace
the constant 0 by IEEE80211_AC_VO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & pointless if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_MAX_QUEUES is an internal mac80211 value,
it is not guaranteed to be always 4. The firmware
API in mwifiex almost certainly doesn't care about
mac80211 changing though, so mwifiex shouldn't use
this value.
Maybe it should use IEEE80211_NUM_ACS instead and
that is what I'm doing here as at least that value
will probably never change, but maybe it should
have its own define instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.
This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618
Reported-and-Tested-by: Da Xue <da@lessconfused.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prefix dmesg output with "iwlwifi: " by
adding #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case of disabled CONFIG_IWLWIFI_DEBUGFS option the compiler complains
about the unused variable 'img'. Fix this by moving the 'img' definition.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Macros can be converted to functions to reduce overall object size.
Convert the ATH5K_PRINTK macro to use _ath5k_printk.
Allyesconfig size is reduced ~10%
$ size drivers/net/wireless/ath/ath5k/built-in.o*
text data bss dec hex filename
211557 2032 40672 254261 3e135 drivers/net/wireless/ath/ath5k/built-in.o.new
235412 2032 47296 284740 45844 drivers/net/wireless/ath/ath5k/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of several unused parameters in struct em28xx_usb_isoc_ctl.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.
The intent in the code was to only use the 'm' measurement if it was a
new minimum. However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.
The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the URBs in em28xx_stop_streaming(), so that em28xx_irq_callback()
cannot be called after the streaming has stopped.
This should eliminate the crashes reported by Antti Palosaari and the warnings
reported by Andy Furniss.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the non-required spinlock acquire/release calls on
'queue_irqlock' from 'uvc_queue_next_buffer' routine.
This routine is called from 'video->encode' function (which translates to either
'uvc_video_encode_bulk' or 'uvc_video_encode_isoc') in 'uvc_video.c'.
As, the 'video->encode' routines are called with 'queue_irqlock' already held,
so acquiring a 'queue_irqlock' again in 'uvc_queue_next_buffer' routine causes
a spin lock recursion.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 3a0db7215c
"TTY: serial, move 68360 driver to staging"
did so because the driver had remained broken since 2008. It also
added this text to the TODO file:
"If no one steps up to adopt any of these drivers, they will
be removed in the 3.4 release."
A quick search on the internet doesn't reveal anyone actively
trying to update/fix this driver, so follow through on the above
and remove it from the pending 3.4 release.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
copy_in_user() already checks for write permission, so we don't need to
do it here. This was added in 1a5e4c867c "[media] uvcvideo: Implement
compat_ioctl32 for custom ioctls".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes BUG_ON in ir_raw_event_thread which IMO is a
over-kill, and this kills the ir_raw_event_thread too. With a bit of
additional logic in this patch, we nomore need to kill this thread.
Other disadvantage of having a BUG-ON is,
wake_up_process(dev->raw->thread) called on dead thread via
ir_raw_event_handle will result in total lockup in SMP system.
Advantage of this patch is ir-raw event thread is left in a usable state
even if the fifo does not have enough bytes.
This patch sets the thread into TASK_INTERRUPTIBLE if raw-fifo has less
then sizeof(struct ir_raw_event) bytes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userptr can be very useful if this device
is requested to use video buffers allocated
by another processing device. So that
buffers don't need to be copied.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit c43b874d5d (tcp: properly initialize tcp memory limits) tried
to fix a regression added in commits 4acb4190 & 3dc43e3,
but still get it wrong.
Result is machines with low amount of memory have too small tcp_rmem[2]
value and slow tcp receives : Per socket limit being 1/1024 of memory
instead of 1/128 in old kernels, so rcv window is capped to small
values.
Fix this to match comment and previous behavior.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lirc sasem and imon drivers now use the module_usb_driver macro, so the old
init/exit function prototypes are useless.
This patch eliminates this warnings:
media_build/v4l/lirc_imon.c:74:19: warning: 'imon_init' declared 'static' but never defined [-Wunused-function]
media_build/v4l/lirc_imon.c:75:20: warning: 'imon_exit' declared 'static' but never defined [-Wunused-function]
media_build/v4l/lirc_sasem.c:84:19: warning: 'sasem_init' declared 'static' but never defined [-Wunused-function]
media_build/v4l/lirc_sasem.c:85:20: warning: 'sasem_exit' declared 'static' but never defined [-Wunused-function]
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now just implementing the exporting APIs, not yet importing. And
kmap is rejected on tiled buffers (although the usefulness of that seems
questionable, but could be added later if needed).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this driver there are several entities associated with separate
platform or I2C client devices, which may get probed in random order.
When the platform device bound to the media device driver is probed
all other entity drivers need to be already in place and initialized.
If any of them is not, fail the media device probe and return an error
indicating we need to be retried once any new driver gets registered.
The media device driver probe will not succeed until there are available
all needed sub-drivers, as specified in the platform data.
While at it, make sure the s5p-csis module (MIPI-CSI receiver driver)
does not get unloaded when in use, by guarding its usage with
try_module_get/module_put.
This patch is a prerequisite for adding the device tree support.
It now also allows again to unbind/bind the driver at runtime from
user space via sysfs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
irq is used only locally and num_clocks is constant, so remove them.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usbdux_attach_common() prints two messages via dev_info() that shows a
device has been attached. The first of these messages includes an index
into a static array that the function determines by pointer subtraction,
assuming the pointer passed to the function points to an element of the
array. Dan Carpenter pointed out that this was kind of ugly. Since the
dev_info() that prints the array index doesn't add anything useful
(since no other messages print the array index and nothing else uses
it), let's just get rid of it.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to the memory-to-memory video node is serialized through a
mutex so now there is no point in having per device context structure
spinlock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the usbdux driver to use the new attach_usb() hook in struct
comedi_driver to auto-configure probed USB devices after the firmware is
loaded.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the amplc_pci224 driver to use the new attach_pci() hook in
struct comedi_driver to auto-configure probed PCI devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prevents blocking on DQBUF at a video capture node in some
conditions, after STREAOMOFF/STREAMON sequence. The ST_CAPT_SUSPEND
flag should not be set during normal stream off, otherwise the
capture engine is not properly enabled at stream on.
Reported-by: Bernard Debbasch <b.debbasch@ssi.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The MIPI-CSI2 data alignment parameter can be derived from media bus
pixel code, so it can be now dropped from the platform data structure.
This is a prerequisite for adding the device tree support. Once this
patch is merged the corresponding fields will be removed from the
drivers' public headers and corresponding board files.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
comedi_auto_config() only needs to consider a single struct
comedi_driver object, but it currently calls comedi_device_attach()
which looks at all struct comedi_driver objects registered with the
Comedi core.
Instead, call the recently added comedi_auto_config_helper() with a new
wrapper comedi_auto_config_wrapper() to mimic the effect of
comedi_device_attach() for a single struct comedi_driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass a pointer to the struct comedi_driver to comedi_auto_config()
instead of the driver name. comedi_auto_config() will be changed to
make use of this. It currently calls comedi_device_attach() which
examines the whole list of struct comedi_driver objects. It will be
changed to restrict itself to just the supplied struct comedi_driver
object.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Comedi auto-configuration mechanism used to bind hardware devices to
comedi devices automatically is pretty kludgy. It fakes a "manual"
configuration of the comedi device as though the COMEDI_DEVCONFIG ioctl
(or the 'comedi_config' utility) were used. In particular, the
low-level comedi driver's '->attach()' routine is called with a pointer
to the struct comedi_device being attached and a pointer to a 'struct
devconfig' containing a device name string and a few integer options to
help the attach routine locate the device being attached. In the case
of PCI devices, these integer options are the PCI bus and slot numbers.
In the case of USB devices, there are no integer options and it relies
more on pot luck to attach the correct device.
This patch adds a couple of bus-type-specific attach routine hooks to
the struct comedi_driver, which a low-level driver can optionally fill
in if it supports auto-configuration.
A low-level driver that supports auto-configuration of {PCI,USB} devices
calls the existing comedi_{pci,usb}_auto_config() when it wishes to
auto-configure a freshly probed device (maybe after loading firmware).
This will call the new '->attach_{pci,usb}()' hook if the driver has
defined it, otherwise it will fall back to calling the '->attach()' hook
as before. The '->attach_{pci,usb}()' hook gets a pointer to the struct
comedi_device and a pointer to the struct {pci_dev,usb_interface} and
can figure out the {PCI,USB} device details for itself.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the post-config part of comedi_device_attach() into new function
comedi_device_postconfig() and rearrange the rest of the function a bit.
The new comedi_device_postconfig() function will be called by some new
bus-type-specific auto-attach functions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comedi_usb_auto_config() and comedi_usb_auto_unconfig() functions
currently take a 'struct usb_device *'. It makes more sense to pass a
'struct usb_interface *' to allow for composite USB devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>