Baltos device provide a mPCIe slot that can be power cycled via a GPIO.
Add a userspace consumer mpcie-power-switch that references a fixed
regulator attached to the GPIO3_4.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20251007085037.3605676-1-yegorslists@googlemail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Without a serial console speed specified in chosen/stdout-path in the
DTB, the serial console uses the default speed of the serial driver,
unless explicitly overridden in a legacy console= kernel command-line
parameter.
After dropping "ti,omap3-uart" from the list of compatible values in DT,
AM33xx serial ports can no longer be used with the legacy OMAP serial
driver, but only with the OMAP-flavored 8250 serial driver (which is
mutually-exclusive with the former). However, replacing
CONFIG_SERIAL_OMAP=y by CONFIG_SERIAL_8250_OMAP=y (with/without enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP) may not be sufficient to restore
serial console functionality: the legacy OMAP serial driver defaults to
115200 bps, while the 8250 serial driver defaults to 9600 bps, causing
no visible output on the serial console when no appropriate console=
kernel command-line parameter is specified.
Fix this for all AM33xx boards by adding ":115200n8" to
chosen/stdout-path. This requires replacing the "&uartN" reference by
the corresponding "serialN" DT alias.
Fixes: ca8be8fc2c ("ARM: dts: am33xx-l4: fix UART compatible")
Fixes: 077e1cde78 ("ARM: omap2plus_defconfig: Enable 8250_OMAP")
Closes: https://lore.kernel.org/CAMuHMdUb7Jb2=GqK3=Rn+Gv5G9KogcQieqDvjDCkJA4zyX4VcA@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/63cef5c3643d359e8ec13366ca79377f12dd73b1.1759398641.git.geert+renesas@glider.be
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The commit 4adc20ba95 ("ARM: dts: broadcom: rpi: Switch to V3D firmware
clock") causes a regression in arm64 developer setups, which stores the
kernel modules via NFS. Before this change the involved V3D clock provider
was builtin, but after this DT change the clk-raspberrypi is responsible
for V3D and for arm64/defconfig this driver is build as a kernel module.
In case these kernel modules are provided via NFS this takes too long and
the PM domain core give up before the clock driver could be loaded:
v3d fec00000.gpu: deferred probe timeout, ignoring dependency
So resolve this issue by making this critical driver builtin.
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/linux-arm-kernel/9ebda74e-e700-4fbe-bca5-382f92417a9c@sirena.org.uk/
Fixes: 4adc20ba95 ("ARM: dts: broadcom: rpi: Switch to V3D firmware clock")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20251104174518.11783-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Quotation marks in cpufeatures.h comments are special and when the
comment begins with a quoted string, that string lands in /proc/cpuinfo,
turning it into a user-visible one.
The LKGS comment doesn't begin with a quoted string but just in case
drop the quoted "kernel" in there to avoid confusion. And while at it,
simply change the description into what the LKGS instruction does for
more clarity.
No functional changes.
Reviewed-by: Xin Li (Intel) <xin@zytor.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20251015103548.10194-1-bp@kernel.org
Fix refcount leak in `smb2_set_path_attr` when path conversion fails.
Function `cifs_get_writable_path` returns `cfile` with its reference
counter `cfile->count` increased on success. Function `smb2_compound_op`
would decrease the reference counter for `cfile`, as stated in its
comment. By calling `smb2_rename_path`, the reference counter of `cfile`
would leak if `cifs_convert_path_to_utf16` fails in `smb2_set_path_attr`.
Fixes: 8de9e86c67 ("cifs: create a helper to find a writeable handle by path name")
Acked-by: Henrique Carvalho <henrique.carvalho@suse.com>
Signed-off-by: Shuhao Fu <sfual@cse.ust.hk>
Signed-off-by: Steve French <stfrench@microsoft.com>
- Use memset() in scx_task_iter_start() instead of zeroing fields individually.
- In scx_task_iter_next(), move __scx_task_iter_maybe_relock() after the batch
check which is simpler.
- Update comment to reflect that tasks are removed from scx_tasks when dead
(commit 7900aa699c ("sched_ext: Fix cgroup exit ordering by moving
sched_ext_free() to finish_task_switch()")).
No functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
The BUILD_BUG_ON() which checks that __SCX_DSQ_ITER_ALL_FLAGS doesn't
overlap with the private lnode bits was in scx_task_iter_start() which has
nothing to do with DSQ iteration. Move it to bpf_iter_scx_dsq_new() where it
belongs.
No functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Alan Maguire says:
====================
Multi-split BTF fixes and test
This small series consists of a fix to multi-split BTF parsing
(patch 1) and a test which exercises (multi-)split BTF parsing
(patch 2).
Changes since v3 [1]
- add asserts to ensure number of types in original and parsed
BTF are identical, and the calls to btf__type_by_id() return
valid pointers (code review bot, patch 2)
Changes since v2 [2]
- fix Fixes: tag formatting (Andrii, patch 1)
- BPF code-review bot saw we were doing ASSERT_OK_PTR() on wrong
BTF (not multisplit) in patch 2
- ensure cleanup is correctly handled for BTF, unlink in split
tests (Andrii, patch 2)
Changes since v1 [3]
- BPF code-review bot spotted another place that the string offset
needed to be adjusted based upon base start string offset + header
string offset.
- added selftests to extend split BTF testing to parsing
[1] https://lore.kernel.org/bpf/20251028225544.1312356-1-alan.maguire@oracle.com/
[2] https://lore.kernel.org/bpf/20251028155709.1265445-1-alan.maguire@oracle.com/
[3] https://lore.kernel.org/bpf/20251023142812.258870-1-alan.maguire@oracle.com/
====================
Link: https://patch.msgid.link/20251104203309.318429-1-alan.maguire@oracle.com
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Write raw BTF to files, parse it and compare to original;
this allows us to test parsing of (multi-)split BTF code.
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20251104203309.318429-3-alan.maguire@oracle.com
When creating multi-split BTF we correctly set the start string offset
to be the size of the base string section plus the base BTF start
string offset; the latter is needed for multi-split BTF since the
offset is non-zero there.
Unfortunately the BTF parsing case needed that logic and it was
missed.
Fixes: 4e29128a9a ("libbpf/btf: Fix string handling to support multi-split BTF")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20251104203309.318429-2-alan.maguire@oracle.com
Add SMMU-V3 Performance Monitoring Counter Group (PMCG) nodes for
Agilex5 to support SMMU performance event monitoring.
Signed-off-by: Adrian Ng Ho Yin <adrianhoyin.ng@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add L2 and L3 cache nodes to the device tree to resolve the
"unable to detect cache hierarchy" warning reported by cacheinfo.
Signed-off-by: Adrian Ng Ho Yin <adrianhoyin.ng@altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Christian Brauner <brauner@kernel.org> says:
The recent changes to rework coredump handling to rely on unix sockets
are in the process of being used in systemd. Yu reported on shortcoming
nameling that the signal causing the coredump was available before the
crashing process was reaped.
The previous systemd coredump container interface requires the coredump
file descriptor, and basic information including the signal number to be
sent to the container. This means we need to have the signal number
available before sending the coredump to the container.
In general, the extension makes sense and fits with the rest of the
coredump information.
In addition to this extension this fixes a bunch of the tests that were
failing and reworks the publication mechanism for exit and coredump info
retrievable via the pidfd ioctl.
* patches from https://patch.msgid.link/20251028-work-coredump-signal-v1-0-ca449b7b7aa0@kernel.org: (22 commits)
selftests/coredump: add second PIDFD_INFO_COREDUMP_SIGNAL test
selftests/coredump: add first PIDFD_INFO_COREDUMP_SIGNAL test
selftests/coredump: ignore ENOSPC errors
selftests/coredump: add debug logging to coredump socket protocol tests
selftests/coredump: add debug logging to coredump socket tests
selftests/coredump: add debug logging to test helpers
selftests/coredump: handle edge-triggered epoll correctly
selftests/coredump: fix userspace coredump client detection
selftests/coredump: fix userspace client detection
selftests/coredump: split out coredump socket tests
selftests/coredump: split out common helpers
selftests/pidfd: add second supported_mask test
selftests/pidfd: add first supported_mask test
selftests/pidfd: update pidfd header
pidfs: expose coredump signal
pidfs: drop struct pidfs_exit_info
pidfs: prepare to drop exit_info pointer
pidfd: add a new supported_mask field
pidfs: add missing BUILD_BUG_ON() assert on struct pidfd_info
pidfs: add missing PIDFD_INFO_SIZE_VER1
...
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-0-ca449b7b7aa0@kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Verify that when using simple socket-based coredump (@ pattern),
the coredump_signal field is correctly exposed as SIGABRT.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-22-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Verify that when using simple socket-based coredump (@ pattern),
the coredump_signal field is correctly exposed as SIGSEGV.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-21-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
If we crash multiple processes at the same time we may run out of space.
Just ignore those errors. They're not actually all that relevant for the
test.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-20-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
PIDFD_INFO_COREDUMP is only retrievable until the task has exited. After
it has exited task->mm is NULL. So if the task didn't actually coredump
we can't retrieve it's dumpability settings anymore. Only if the task
did coredump will we have stashed the coredump information in the
respective struct pid.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-15-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Verify that when PIDFD_INFO_SUPPORTED_MASK is requested, the kernel
returns the supported_mask field indicating which flags the kernel
supports.
Link: https://patch.msgid.link/20251028-work-coredump-signal-v1-10-ca449b7b7aa0@kernel.org
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Currently the automatic block layer PI generation allocates the integrity
buffer using kmalloc, and thus could deadlock, or fail I/O request due
to memory pressure.
Fix this by adding a mempool, and capping the maximum I/O size on PI
capable devices to not exceed the allocation size of the mempool.
Link: https://lore.kernel.org/linux-block/20251103101653.2083310-1-hch@lst.de/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* autopi-deadlock:
block: make bio auto-integrity deadlock safe
block: blocking mempool_alloc doesn't fail
The current block layer automatic integrity protection allocates the
actual integrity buffer, which has three problems:
- because it happens at the bottom of the I/O stack and doesn't use a
mempool it can deadlock under load
- because the data size in a bio is almost unbounded when using lage
folios it can relatively easily exceed the maximum kmalloc size
- even when it does not exceed the maximum kmalloc size, it could
exceed the maximum segment size of the device
Fix this by limiting the I/O size so that we can allocate at least a
2MiB integrity buffer, i.e. 128MiB for 8 byte PI and 512 byte integrity
intervals, and create a mempool as a last resort for this maximum size,
mirroring the scheme used for bvecs. As a nice upside none of this
can fail now, so we remove the error handling and open code the
trivial addition of the bip vec.
The new allocation helpers sit outside of bio-integrity-auto.c because
I plan to reuse them for file system based PI in the near future.
Fixes: 7ba1ba12ee ("block: Block layer data integrity support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
So remove the error check for it in bio_integrity_prep.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Anuj Gupta <anuj20.g@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Debian 13 (released 2025-08-09) packages Rust 1.85.0 [1], which is recent
enough to build Linux.
Thus document it.
In fact, we are planning to propose that the minimum supported Rust
version in Linux follows Debian Stable releases, with Debian 13 being
the first one we upgrade to, i.e. Rust 1.85.
Link: https://www.debian.org/News/2025/20250809 [1]
Link: https://patch.msgid.link/20251012224645.1148411-1-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Following fixes:
- Memory leak in bnxt GSI qp path
- Failure in irdma registering large MRs
- Failure to clean out the right CQ table entry in irdma
- Invalid vf_id in some cases
- Incorrect error unwind in EFA CQ create
- hns doesn't use the optimal cq/qp relationships for it's HW banks
- hns reports the wrong SGE size to userspace for its QPs
- Corruption of the hns work queue entries in some cases
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRRRCHOFoQz/8F5bUaFwuHvBreFYQUCaQoEZAAKCRCFwuHvBreF
YbdjAP9MfjyZvmOu5H7yqwdIgCNeduANVWbEzSXUEU6j5LRCywD+O5UnkPbHQ9ko
k+jo07V6Ra/FuTVmr1Wf/Nfa9JmPqwc=
=dnEg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
- Memory leak in bnxt GSI qp path
- Failure in irdma registering large MRs
- Failure to clean out the right CQ table entry in irdma
- Invalid vf_id in some cases
- Incorrect error unwind in EFA CQ create
- hns doesn't use the optimal cq/qp relationships for it's HW banks
- hns reports the wrong SGE size to userspace for its QPs
- Corruption of the hns work queue entries in some cases
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
MAINTAINERS: Update irdma maintainers
RDMA/irdma: Fix vf_id size to u16 to avoid overflow
RDMA/hns: Remove an extra blank line
RDMA/hns: Fix wrong WQE data when QP wraps around
RDMA/hns: Fix the modification of max_send_sge
RDMA/hns: Fix recv CQ and QP cache affinity
RDMA/uverbs: Fix umem release in UVERBS_METHOD_CQ_CREATE
RDMA/irdma: Set irdma_cq cq_num field during CQ create
RDMA/irdma: Fix SD index calculation
RDMA/bnxt_re: Fix a potential memory leak in destroy_gsi_sqp
This is supposed to be "priv" but we accidentally pass "&priv" which is
an address in the stack and so it will lead to memory corruption when
the imx_sc_key_action() function is called. Remove the &.
Fixes: 768062fd12 ("Input: imx_sc_key - use devm_add_action_or_reset() to handle all cleanups")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/aQYKR75r2VMFJutT@stanley.mountain
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If process is killed. the vm entity is stopped, submit pt update job
will trigger the error message "*ERROR* Trying to push to a killed
entity", job will not execute.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 10c382ec6c)
Cc: stable@vger.kernel.org
Fix the flows for S0ix. There is no need to stop
rlc or reintialize PMFW in S0ix.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4659
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reported-by: Antheas Kapenekakis <lkml@antheas.dev>
Tested-by: Antheas Kapenekakis <lkml@antheas.dev>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit fd39b5a583)
Cc: <stable@vger.kernel.org> # c81f5cebe8: drm/amdgpu: Drop PMFW RLC notifier from amdgpu_device_suspend()
Cc: <stable@vger.kernel.org>
For S3 on vangogh, PMFW needs to be notified before the
driver powers down RLC. This already happens in smu_disable_dpms()
so drop the superfluous call in amdgpu_device_suspend().
Co-developed-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 960e30a61e)
Update the table of program types in the libbpf docs with the missing
k/uprobe multi and session program types.
Signed-off-by: Donald Hunter <donald.hunter@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20251029180932.98038-1-donald.hunter@gmail.com
[Why & How]
This fixes the black screen issue on certain APUs with HDMI,
accompanied by the following messages:
amdgpu 0000:c4:00.0: amdgpu: [drm] Failed to setup vendor info
frame on connector DP-1: -22
amdgpu 0000:c4:00.0: [drm] Cannot find any crtc or sizes [drm]
Cannot find any crtc or sizes
Fixes: 489f0f600c ("drm/amd/display: Fix DVI-D/HDMI adapters")
Suggested-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 678c901443)
commit 978fa2f6d0 ("drm/amd/display: Use scaling for non-native
resolutions on eDP") started using the GPU scaler hardware to scale
when a non-native resolution was picked on eDP. This scaling was done
to fill the screen instead of maintain aspect ratio.
The idea was supposed to be that if a different scaling behavior is
preferred then the compositor would request it. The not following
aspect ratio behavior however isn't desirable, so adjust it to follow
aspect ratio and still try to fill screen.
Note: This will lead to black bars in some cases for non-native
resolutions. Compositors can request the previous behavior if desired.
Fixes: 978fa2f6d0 ("drm/amd/display: Use scaling for non-native resolutions on eDP")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4538
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 825df7ff4b)
Commit be2f2d1680 ("libbpf: Deprecate bpf_program__load() API") marked
bpf_program__load() as deprecated starting with libbpf v0.6. And later
in commit 146bf811f5 ("libbpf: remove most other deprecated high-level
APIs") actually removed the bpf_program__load() implementation and
related old high-level APIs.
This patch update the comment in bpf_program__set_attach_target() to
remove the reference to the deprecated interface bpf_program__load().
Signed-off-by: Jianyun Gao <jianyungao89@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20251103120727.145965-1-jianyungao89@gmail.com
Use the correct label to complete all cleanup work.
Fixes: 4d154b1ca5 ("drm/amd/pm: Add support for DPM policies")
Fixes: 25e82f2e2c ("drm/amd/pm: Add temperature metrics sysfs entry")
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4c4c138a1c)
These were not set so soft recovery was inadvertantly
disabled.
Fixes: 6ac55eab4f ("drm/amdgpu: move reset support type checks into the caller")
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1972763505)
Currently, the export of kvm_zap_gfn_range() is misplaced, i.e., it's
not placed right after the kvm_zap_gfn_range() function body but after
kvm_mmu_zap_collapsible_spte(). Move it to the right place.
No functional change intended.
Signed-off-by: Kai Huang <kai.huang@intel.com>
Link: https://patch.msgid.link/20251021114345.159372-1-kai.huang@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
