Commit graph

1,403,262 commits

Author SHA1 Message Date
Dr. David Alan Gilbert
d40f4b15c0 media: cx23885: Remove unused netup_eeprom_write
netup_eeprom_write() was added in 2009 by
commit b45c0551f9 ("V4L/DVB (10797): Add EEPROM code for NetUP Dual
DVB-S2 CI card.")
but has remained unused.

Remove it.

Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2025-02-25 09:14:05 +01:00
Colin Ian King
d93c0a7923 media: hi556: remove redundant assignment to variable enable
The variable enable is being assigned a value that is never read
afterwards. The assignment is redundant and can be removed.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2025-02-25 09:14:05 +01:00
Matthias Fend
7d8fa0ee43 media: tc358746: fix locking issue
In tc358746_link_validate() an attempt is made to get the state lock of the
subdev, but since this is already held by the calling function
v4l2_subdev_link_validate(), this leads to a deadlock.
Another problem is that this function queries the link frequency of the
source device. Since some image sensors use the lock of the v4l2 control
handler as a state lock, which is already held at this point, a deadlock
can also occur here.
Move the calculation of the FIFO size from tc358746_link_validate() to
tc358746_apply_misc_config() to avoid the deadlocks mentioned.

Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2025-02-25 09:07:25 +01:00
Matthias Fend
78d7265e2e media: tc358746: improve calculation of the D-PHY timing registers
When calculating D-PHY registers, using data rates that are not multiples
of 16 can lead to precision loss in division operations. This can result in
register values that produce timing violations against the MIPI standard.

An example:
cfg->hs_clk_rate = 294MHz
hf_clk = 18

If the desired value in cfg->init is 100us, which is the minimum allowed
value, then the LINEINITCNT register is calculated as 1799. But since the
actual clock is 18.375MHz instead of 18MHz, this setting results in a time
that is shorter than 100us and thus violates the standard. The correct
value for LINEINITCNT would be 1837.

Improve the precision of calculations by using Hz instead of MHz as unit.

Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2025-02-25 09:07:25 +01:00
Matthias Fend
44967f0933 media: tc358746: add support for 8/10/12/14-bit RAW Bayer formats
The TC358746 supports RAW formats with 8, 10, 12, and 14-bit depths. Since
pixel data is transported transparently without modifying the pixel
arrangement, all Bayer patterns (RGGB, BGGR, GRBG, GBRG) are supported.

Signed-off-by: Matthias Fend <matthias.fend@emfend.at>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2025-02-25 09:07:25 +01:00
Dave Airlie
fb51bf0255 Linux 6.14-rc4
-----BEGIN PGP SIGNATURE-----
 
 iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAme7hfkeHHRvcnZhbGRz
 QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGU+IH/1bk6zIvAwXXS5yu
 KNsQ8dEkC3Xme6HqLtPsAhRLF+5YJf6MaGm1ip5dDMyIvasa2gwvCQQQoOpeMbKj
 79VKT+m9t3szMHZaQYjlOuYHBmNSJ4cMCD2Qh6ktXHGPfTTWDFGf7fBwBOkVNeJU
 1Ask+bxeop21aJMhfYXrUta3OYyerLBUR6jCiCM82A/GLtdv6oNGXBu3ygDt9Tjx
 ZHSl+CYjKpmGUP8JnMKwCBHVguEfqgzZ//dY1H16AvOLed9k2jkMFn8O5Vi3vjnx
 TWMMXoiJimuamGzbjxtCCqzxNlFFDT4gRpDqeJxb16W/gDTFmbRr9LDjNehCZe33
 AigLZ6M=
 =Y/7F
 -----END PGP SIGNATURE-----

Merge tag 'v6.14-rc4' into drm-next

Backmerge Linux 6.14-rc4 at the request of tzimmermann so misc-next
can base on rc4.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2025-02-25 17:36:09 +10:00
Fiona Behrens
040b17ae0e rust: io: fix devres test with new io accessor functions
Fix doctest of `Devres` which still used `writeb` instead of `write8`.

Fixes: 354fd6e86f ("rust: io: rename `io::Io` accessors")
Signed-off-by: Fiona Behrens <me@kloenk.dev>
Link: https://lore.kernel.org/r/20250224-rust-iowrite-read8-fix-v1-1-c6abee346897@kloenk.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-02-25 07:29:48 +01:00
Luca Weiss
3b00110593 Input: goodix-berlin - fix vddio regulator references
As per dt-bindings the property is called vddio-supply, so use the
correct name in the driver instead of iovdd. The datasheet also calls
the supply 'VDDIO'.

Fixes: 44362279bd ("Input: add core support for Goodix Berlin Touchscreen IC")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250103-goodix-berlin-fixes-v1-2-b014737b08b2@fairphone.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2025-02-24 22:28:50 -08:00
Luca Weiss
5bab1ae5a3 Input: goodix-berlin - fix comment referencing wrong regulator
In the statement above AVDD gets enabled, and not IOVDD, so fix this
copy-paste mistake.

Fixes: 44362279bd ("Input: add core support for Goodix Berlin Touchscreen IC")
Reported-by: Jens Reidel <adrian@travitia.xyz>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250103-goodix-berlin-fixes-v1-1-b014737b08b2@fairphone.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2025-02-24 22:28:49 -08:00
Heiner Kallweit
a3e51d4711 net: phy: add phylib-internal.h
This patch is a starting point for moving phylib-internal
declarations to a private header file.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/082eacd2-a888-4716-8797-b3491ce02820@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 19:14:31 -08:00
Jakub Kicinski
7842f3d15a Merge branch 'mptcp-pm-misc-cleanups-part-3'
Matthieu Baerts says:

====================
mptcp: pm: misc cleanups, part 3

These cleanups lead the way to the unification of the path-manager
interfaces, and allow future extensions. The following patches are not
all linked to each others, but are all related to the path-managers,
except the last three.

- Patch 1: remove unused returned value in mptcp_nl_set_flags().
- Patch 2: new flag: avoid iterating over all connections if not needed.
- Patch 3: add a build check making sure there is enough space in cb-ctx.
- Patch 4: new mptcp_pm_genl_fill_addr helper to reduce duplicated code.
- Patch 5: simplify userspace_pm_append_new_local_addr helper.
- Patch 6: drop unneeded inet6_sk().
- Patch 7: use ipv6_addr_equal() instead of !ipv6_addr_cmp()
- Patch 8: scheduler: split an interface in two.
- Patch 9: scheduler: save 64 bytes of currently unused data.
- Patch 10: small optimisation to exit early in case of retransmissions.
====================

Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-0-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:46 -08:00
Matthieu Baerts (NGI0)
8275ac799e mptcp: blackhole: avoid checking the state twice
A small cleanup, reordering the conditions to avoid checking things
twice.

The code here is called in case of timeout on a TCP connection, before
triggering a retransmission. But it only acts on SYN + MPC packets.

So the conditions can be re-order to exit early in case of non-MPTCP
SYN + MPC. This also reduce the indentation levels.

Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-10-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:44 -08:00
Matthieu Baerts (NGI0)
b68b106b0f mptcp: sched: reduce size for unused data
Thanks for the previous commit ("mptcp: sched: split get_subflow
interface into two"), the mptcp_sched_data structure is now currently
unused.

This structure has been added to allow future extensions that are not
ready yet. At the end, this structure will not even be used at all when
mptcp_subflow bpf_iter will be supported [1].

Here is a first step to save 64 bytes on the stack for each scheduling
operation. The structure is not removed yet not to break the WIP work on
these extensions, but will be done when [1] will be ready and applied.

Link: https://lore.kernel.org/6645ad6e-8874-44c5-8730-854c30673218@linux.dev [1]
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-9-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:44 -08:00
Geliang Tang
9771a96a7a mptcp: sched: split get_subflow interface into two
get_retrans() interface of the burst packet scheduler invokes a sleeping
function mptcp_pm_subflow_chk_stale(), which calls __lock_sock_fast().
So get_retrans() interface should be set with BPF_F_SLEEPABLE flag in
BPF. But get_send() interface of this scheduler can't be set with
BPF_F_SLEEPABLE flag since it's invoked in ack_update_msk() under mptcp
data lock.

So this patch has to split get_subflow() interface of packet scheduer into
two interfaces: get_send() and get_retrans(). Then we can set get_retrans()
interface alone with BPF_F_SLEEPABLE flag.

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-8-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:44 -08:00
Geliang Tang
7720790fd5 mptcp: pm: use ipv6_addr_equal in addresses_equal
Use ipv6_addr_equal() to check whether two IPv6 addresses are equal in
mptcp_addresses_equal().

This is more appropriate than using !ipv6_addr_cmp().

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-7-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:44 -08:00
Geliang Tang
dc41695200 mptcp: pm: drop inet6_sk after inet_sk
In mptcp_event_add_subflow(), mptcp_event_pm_listener() and
mptcp_nl_find_ssk(), 'issk' has already been got through inet_sk().

No need to use inet6_sk() to get 'ipv6_pinfo' again, just use
issk->pinet6 instead. This patch also drops these 'ipv6_pinfo'
variables.

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-6-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Geliang Tang
640e3d69d0 mptcp: pm: drop match in userspace_pm_append_new_local_addr
The variable 'match' in mptcp_userspace_pm_append_new_local_addr() is a
redundant one, and this patch drops it.

No need to define 'match' as 'struct mptcp_pm_addr_entry *' type. In this
function, it's only used to check whether it's NULL. It can be defined as
a Boolean one.

Also other variables 'addr_match' and 'id_match' make 'match' a redundant
one, which can be replaced by directly checking 'addr_match && id_match'.

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-5-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Geliang Tang
f8fe817465 mptcp: pm: add mptcp_pm_genl_fill_addr helper
To save some redundant code in dump_addr() interfaces of both the
netlink PM and userspace PM, the code that calls netlink message
helpers (genlmsg_put/cancel/end) and mptcp_nl_fill_addr() is wrapped
into a new helper mptcp_pm_genl_fill_addr().

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-4-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Geliang Tang
63132fb054 mptcp: pm: add a build check for userspace_pm_dump_addr
This patch adds a build check for mptcp_userspace_pm_dump_addr() to make
sure there is enough space in 'cb->ctx' to store an address id bitmap.

Just in case info stored in 'cb->ctx' are increased later.

Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-3-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Matthieu Baerts (NGI0)
145dc6cc4a mptcp: pm: change to fullmesh only for 'subflow'
If an endpoint doesn't have the 'subflow' flag -- in fact, has no type,
so not 'subflow', 'signal', nor 'implicit' -- there are then no subflows
created from this local endpoint to at least the initial destination
address. In this case, no need to call mptcp_pm_nl_fullmesh() which is
there to recreate the subflows to reflect the new value of the fullmesh
attribute.

Similarly, there is then no need to iterate over all connections to do
nothing, if only the 'fullmesh' flag has been changed, and the endpoint
doesn't have the 'subflow' one. So stop early when dealing with this
specific case.

Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-2-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Matthieu Baerts (NGI0)
bc337e8c0e mptcp: pm: remove unused ret value to set flags
The returned value is not used, it can then be dropped.

Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250221-net-next-mptcp-pm-misc-cleanup-3-v1-1-2b70ab1cee79@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:23:43 -08:00
Thorsten Blum
8f3f4464ff net/mlx5: Use secs_to_jiffies() instead of msecs_to_jiffies()
Use secs_to_jiffies() and simplify the code.

Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://patch.msgid.link/20250221085350.198024-3-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:20:33 -08:00
Jakub Kicinski
79936fcb77 Merge branch 'net-mlx5e-move-ipsec-policy-check-after-decryption'
Tariq Toukan says:

====================
net/mlx5e: Move IPSec policy check after decryption

This series by Jianbo adds IPsec policy check after decryption.

In current mlx5 driver, the policy check is done before decryption for
IPSec crypto and packet offload. This series changes that order to
make it consistent with the processing in kernel xfrm. Besides, RX
state with UPSPEC selector is supported correctly after new steering
table is added after decryption and before the policy check.
====================

Link: https://patch.msgid.link/20250220213959.504304-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:15:19 -08:00
Jianbo Liu
c69046c3f2 net/mlx5e: Support RX xfrm state selector's UPSPEC for packet offload
Previously, the upper layer matches are added for the decryption rule
when xfrm selector's UPSPEC is specified in the command. However, it's
impossible as packets are not decrypted, and there is no way to do
match on the upper protocol (TCP/UDP) with specific source/destination
port. The result is that packets are not decrypted by hardware because
of this mismatch. Instead, they are forwarded to kernel, and
decryption is done by software.

To resolve this issue, this patch adds new table (sa_sel) after status
table and before policy table. When UPSPEC's proto is specified in
xfrm state's selector, a rule is added in status table to forward the
decrypted packets to sa_sel table, where the corresponding rule for
selector's UPSPEC is added, and packet's upper headers are checked
there. If matched, they will be forward to policy table to do policy
check. Otherwise, they are dropped immediately.

Besides, add a global count for this kind of packet drop.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-9-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:33 -08:00
Jianbo Liu
78e77a41e4 net/mlx5e: Add pass flow group for IPSec RX status table
This flow group is added for the pass rules for both crypto offload
and packet offload. It is placed at the end of the table, and right
before the miss group. There are two entries, and the default pass
rules for both offloads are added in this group.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-8-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
e20674a7e5 net/mlx5e: Add num_reserved_entries param for ipsec_ft_create()
Add parameter for ipsec_ft_create() to pass the number of the reserved
entries when creating auto-grouped flow table. It's used to create
table with pre-defined group(s) which may have more than one rule.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-7-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
aa2961e19f net/mlx5e: Skip IPSec RX policy check for crypto offload
For crypto offload, there is no xfrm policy rule offloaded to
hardware, so no need to continue with policy check for it.

Previously, for crypto offload, the hardware metadata reg c4 is not
used and not changed, but set to ASO_OK(0) before decryption to avoid
garbage data. Then a default rule is added to check ipsec_syndrome and
this register. Packets are forwarded to policy table if succeed, or
drop if fails.

According to hardware document, this register value could be 0, 1.
So a special value (0xAA), which is not used by hardware, is chosen as
an indication for crypto offload. It is set to c4 before decryption.
Then a default rule, which matches on 0xAA (and ipsec_syndrome on 0),
is added, which means packets are done by crypto offload, and
sends them to kernel directly, thus skips the policy check.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-6-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
7d9e292ecd net/mlx5e: Move IPSec policy check after decryption
Currently, xfrm policy check is done before decryption in mlx5 driver.
If matching any policy, packets are forwarded to xfrm state table for
decryption. But this is exact opposite to what software does. For
kernel implementation, xfrm decode is unconditionally activated
whenever an IPSec packet reaches the input flow if there’s a matching
state rule.

This patch changes the order, move policy check after decryption.
Besides, a miss flow table is added at the end for legacy mode, to
make it easier to update the default destination of the steering rules.

So ESP packets are firstly forwarded to SA table for decryption, then
the result is checked in status table. If the decryption succeeds,
packets are forwarded to another table to check xfrm policy rules.
When a policy with allow action is matched, if in legacy mode packets
are forwarded to miss flow table with one rule to forward them to RoCE
tables, if in switchdev mode they are forwarded directly to TC root
chain instead.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
85e4a808af net/mlx5e: Add correct match to check IPSec syndromes for switchdev mode
In commit dddb49b63d ("net/mlx5e: Add IPsec and ASO syndromes check
in HW"), IPSec and ASO syndromes checks after decryption for the
specified ASO object were added. But they are correct only for eswith
in legacy mode. For switchdev mode, metadata register c1 is used to
save the mapped id (not ASO object id). So, need to change the match
accordingly for the check rules in status table.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
20d5fdc895 net/mlx5e: Change the destination of IPSec RX SA miss rule
For eswitch in legacy mode, the packets decrypted in RX SA table will
continue to be processed for RoCE. But this is not necessary for the
un-decrypted packets, which don't match any decryption rules but hit
the miss rule at the end of the table. So, change the destination of
miss rule to TTC default one and skip RoCE.

For eswitch in switchdev mode, the destination is unchanged.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jianbo Liu
3400ae49cd net/mlx5e: Add helper function to update IPSec default destination
The default destination of IPSec steering rules for MPV mode will be
updated when the master device is brought up or down. Move the common
code into the helper function. It’s convenient to update destinations
in later patches.

Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250220213959.504304-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:14:32 -08:00
Jiawen Wu
a3ad653c91 net: wangxun: Replace the judgement of MAC type with flags
Since device MAC types are constantly being added, the judgments of
wx->mac.type are complex. Try to convert the types to flags depending
on functions.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250221065718.197544-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:13:00 -08:00
Jiawen Wu
2e5af6b2ae net: txgbe: Add basic support for new AML devices
There is a new 40/25/10 Gigabit Ethernet device.

To support basic functions, PHYLINK is temporarily skipped as it is
intended to implement these configurations in the firmware. And the
associated link IRQ is also skipped.

And Implement the new SW-FW interaction interface, which use 64 Byte
message buffer.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250221065718.197544-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 18:13:00 -08:00
Andras Sebok
83a4a5a82a Input: imagis - add support for imagis IST3038H
Add support for imagis IST3038H, which seems mostly compatible with
IST3038C except that it reports a different chip ID value.

Tested on samsung,j5y17lte.

Signed-off-by: Andras Sebok <sebokandris2009@gmail.com>
Link: https://lore.kernel.org/r/20250224090354.102903-2-sebokandris2009@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2025-02-24 18:11:06 -08:00
Paul Fertser
5797c04400 hwmon: (peci/dimmtemp) Do not provide fake thresholds data
When an Icelake or Sapphire Rapids CPU isn't providing the maximum and
critical thresholds for particular DIMM the driver should return an
error to the userspace instead of giving it stale (best case) or wrong
(the structure contains all zeros after kzalloc() call) data.

The issue can be reproduced by binding the peci driver while the host is
fully booted and idle, this makes PECI interaction unreliable enough.

Fixes: 73bc1b885d ("hwmon: peci: Add dimmtemp driver")
Fixes: 621995b6d7 ("hwmon: (peci/dimmtemp) Add Sapphire Rapids support")
Cc: stable@vger.kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20250123122003.6010-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2025-02-24 18:10:10 -08:00
Andras Sebok
f5be37ca2c dt-bindings: input/touchscreen: imagis: add compatible for ist3038h
IST3038H is a touchscreen IC which seems mostly compatible with IST3038C
except that it reports a different chip ID value.

Signed-off-by: Andras Sebok <sebokandris2009@gmail.com>
Link: https://lore.kernel.org/r/20250224090354.102903-4-sebokandris2009@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2025-02-24 18:05:57 -08:00
Bart Van Assche
ac0fb4a55b scsi: scsi_debug: Do not sleep in atomic sections
Function stop_qc_helper() is called while the debug_scsi_cmd lock is held,
and from here we may call cancel_work_sync(), which may sleep.

Sleeping in atomic sections is not allowed.

Hence change the cancel_work_sync() call into a cancel_work() call.

However now it is not possible to know if the work callback is running when
we return. This is relevant for eh_abort_handler handling, as the semantics
of that callback are that success means that we do not keep a reference to
the scsi_cmnd - now this is not possible. So return FAIL when we are unsure
if the callback still running.

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
jpg: return FAILED from scsi_debug_abort() when possible callback running
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250224115517.495899-5-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:53:07 -05:00
Bart Van Assche
b441eafbd1 scsi: scsi_debug: Simplify command handling
Simplify command handling by moving struct sdebug_defer into the private
SCSI command data instead of allocating it separately. The only functional
change is that aborting a SCSI command now fails and is retried at a later
time if the completion handler can't be cancelled.

See also commit 1107c7b24e ("scsi: scsi_debug: Dynamically allocate
sdebug_queued_cmd").

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250224115517.495899-4-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:53:07 -05:00
Bart Van Assche
7f92ca91c8 scsi: scsi_debug: Remove a reference to in_use_bm
Commit f1437cd1e5 ("scsi: scsi_debug: Drop sdebug_queue") removed the
'in_use_bm' struct member. Hence remove a reference to that struct member
from the procfs host info file.

Fixes: f1437cd1e5 ("scsi: scsi_debug: Drop sdebug_queue")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250224115517.495899-3-john.g.garry@oracle.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:53:07 -05:00
John Garry
2af3b0c108 scsi: scsi_debug: Remove sdebug_device_access_info
This structure is not used, so delete it.

It was originally intended for supporting checking for atomic writes
overlapping with ongoing reads and writes, but that support never got
added.

SBC-4 r22 section 4.29.3.2 "Performing operations during an atomic write
operation" describes two methods of handling overlapping atomic writes.
Currently the only method supported is for the ongoing read or write to
complete.

Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20250224115517.495899-2-john.g.garry@oracle.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:53:07 -05:00
Thorsten Blum
6538c8ca8e net: ethernet: renesas: rcar_gen4_ptp: Remove bool conversion
Remove the unnecessary bool conversion and simplify the code.

Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20250223233613.100518-2-thorsten.blum@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2025-02-24 17:50:16 -08:00
Yuichiro Tsuji
0107fb8686 scsi: qla2xxx: Fix typos in a comment
Fix typos in a comment.

hapens -> happens
recommeds -> recommends

Signed-off-by: Yuichiro Tsuji <yuichtsu@amazon.com>
Link: https://lore.kernel.org/r/20250224075907.2505-1-yuichtsu@amazon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:08:57 -05:00
Colin Ian King
c337ce64ea scsi: mpt3sas: Fix spelling mistake "receveid" -> "received"
There is a spelling mistake in a ioc_err message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20250221083253.77496-1-colin.i.king@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:07:56 -05:00
Kaixin Wang
e3f88665a7 HSI: ssi_protocol: Fix use after free vulnerability in ssi_protocol Driver Due to Race Condition
In the ssi_protocol_probe() function, &ssi->work is bound with
ssip_xmit_work(), In ssip_pn_setup(), the ssip_pn_xmit() function
within the ssip_pn_ops structure is capable of starting the
work.

If we remove the module which will call ssi_protocol_remove()
to make a cleanup, it will free ssi through kfree(ssi),
while the work mentioned above will be used. The sequence
of operations that may lead to a UAF bug is as follows:

CPU0                                    CPU1

                        | ssip_xmit_work
ssi_protocol_remove     |
kfree(ssi);             |
                        | struct hsi_client *cl = ssi->cl;
                        | // use ssi

Fix it by ensuring that the work is canceled before proceeding
with the cleanup in ssi_protocol_remove().

Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240918120749.1730-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2025-02-25 02:07:09 +01:00
Martin K. Petersen
7507203e68 Merge patch series "mpi3mr: Few Enhancements and minor fixes"
Ranjan Kumar <ranjan.kumar@broadcom.com> says:

Few Enhancements and minor fixes of mpi3mr driver.

Link: https://lore.kernel.org/r/20250220142528.20837-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 20:03:00 -05:00
Ranjan Kumar
95dc5b979f scsi: mpi3mr: Update driver version to 8.13.0.5.50
Update driver version to 8.13.0.5.50

Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250220142528.20837-5-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 19:57:44 -05:00
Ranjan Kumar
ca41929b2e scsi: mpi3mr: Check admin reply queue from Watchdog
Admin reply processing can be called from multiple contexts. The driver
uses an atomic flag for synchronization among multiple threads/context for
draining the admin replies.

Upon entering the admin processing routine, the driver will set the atomic
flag and start reply processing. When exiting the routine, the driver
resets the flag. However, there is a race condition when one thread (Thread
1) has processed replies and is about to reset the flag but in the meantime
few more replies are posted and another thread (Thread 2) is called to
process replies. Since the synchronization flag is still set, Thread 2 will
return without processing replies and those new replies will not be
flushed.

Make the watchdog thread monitor cases where admin ISR/poll call returns
due to another thread processing admin replies. If such an instance is
found, make driver call admin ISR to drain replies (if any).

Co-developed-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250220142528.20837-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 19:57:44 -05:00
Ranjan Kumar
83a9d30d29 scsi: mpi3mr: Update timestamp only for supervisor IOCs
The driver issues the time stamp update command periodically. Even if the
command fails with supervisor only IOC Status.

Instead check the Non-Supervisor capability bit reported by IOC as part of
IOC Facts.

Co-developed-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250220142528.20837-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 19:57:44 -05:00
Ranjan Kumar
b928757432 scsi: mpi3mr: Update MPI Headers to revision 35
Update MPI Headers to revision 35

Co-developed-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Prayas Patel <prayas.patel@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20250220142528.20837-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2025-02-24 19:57:44 -05:00
Raag Jadav
76d5fb0e58 power: supply: sc27xx: use devm_kmemdup_array()
Convert to use devm_kmemdup_array() which is more robust.

Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Link: https://lore.kernel.org/r/20250221165333.2780888-9-raag.jadav@intel.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2025-02-25 01:50:38 +01:00