Define the USB-C orientation GPIOs so that the USB-C ports orientation
is known without having to resort to the altmode notifications.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240409-hdk-orientation-gpios-v2-4-658efd993987@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define the USB-C orientation GPIO so that the USB-C port orientation is
known without having to resort to the altmode notifications.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240409-hdk-orientation-gpios-v2-3-658efd993987@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define the USB-C orientation GPIO so that the USB-C port orientation is
known without having to resort to the altmode notifications.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240409-hdk-orientation-gpios-v2-2-658efd993987@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The orientation GPIOs are not limited to sm8450/sm8550/x1e8000
platforms. Allow corresponding property to be used on all Qualcom
platforms.
Fixes: 65682407f8 ("dt-bindings: soc: qcom: qcom,pmic-glink: add a gpio used to determine the Type-C port plug orientation")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240409-hdk-orientation-gpios-v2-1-658efd993987@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Define the USB-C orientation GPIOs so that the USB-C ports orientation
is known without having to resort to the altmode notifications.
On PCB level this is the signal from PM7250B (pin CC_OUT) which is
called USB_PHY_PS.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240411-fp5-usb-c-gpio-v1-1-78f11deb940a@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Without explicitly specifying names for the regulators they are named
based on the DeviceTree node name. This results in multiple regulators
with the same name, making it impossible to reason debug prints and
regulator_summary.
Signed-off-by: Umang Chheda <quic_uchheda@quicinc.com>
Link: https://lore.kernel.org/r/20240412123237.2633000-1-quic_uchheda@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Voltage regulator L13C is used by SD card IO interface. In order to
support UHS modes, IO interface voltage needs to be set to 1.8V. This
patch extends minimum voltage range of L13C regulator to allow this.
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Fixes: 0deb2624e2 ("arm64: dts: qcom: sa8155p-adp: Add support for uSD card")
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20240412190310.1647893-2-volodymyr_babchuk@epam.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are two issues with SDHC2 configuration for SA8155P-ADP,
which prevent use of SDHC2 and causes issues with ethernet:
- Card Detect pin for SHDC2 on SA8155P-ADP is connected to gpio4 of
PMM8155AU_1, not to SoC itself. SoC's gpio4 is used for DWMAC
TX. If sdhc driver probes after dwmac driver, it reconfigures
gpio4 and this breaks Ethernet MAC.
- pinctrl configuration mentions gpio96 as CD pin. It seems it was
copied from some SM8150 example, because as mentioned above,
correct CD pin is gpio4 on PMM8155AU_1.
This patch fixes both mentioned issues by providing correct pin handle
and pinctrl configuration.
Fixes: 0deb2624e2 ("arm64: dts: qcom: sa8155p-adp: Add support for uSD card")
Cc: stable@vger.kernel.org
Signed-off-by: Volodymyr Babchuk <volodymyr_babchuk@epam.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20240412190310.1647893-1-volodymyr_babchuk@epam.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
- Mediatek mt7988 has broken PCIe because the wrong parent is used
- Mediatek clk drivers may deadlock when registering their clks because
the clk provider device is repeatedly runtime PM resumed and
suspended during probe and clk registration. Resuming the clk
provider device deadlocks with an ABBA deadlock due to genpd_lock and
the clk prepare_lock. The fix is to keep the device runtime resumed
while registering clks.
- Another runtime PM related deadlock, this time with disabling unused
clks during late init. We get an ABBA deadlock where a device is
runtime PM resuming (or suspending) while the disabling of unused
clks is happening in parallel. That runtime PM action calls into the
clk framework and tries to grab the clk prepare_lock while the
disabling of unused clks holds the prepare_lock and is waiting for
that runtime PM action to complete. The fix is to runtime resume all
the clk provider devices before grabbing the clk prepare_lock during
disable unused.
- A build fix to provide an empty devm_clk_rate_exclusive_get()
function when CONFIG_COMMON_CLK=n
-----BEGIN PGP SIGNATURE-----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=RLMP
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple clk driver fixes, a build fix, and a deadlock fix:
- Mediatek mt7988 has broken PCIe because the wrong parent is used
- Mediatek clk drivers may deadlock when registering their clks
because the clk provider device is repeatedly runtime PM resumed
and suspended during probe and clk registration.
Resuming the clk provider device deadlocks with an ABBA deadlock
due to genpd_lock and the clk prepare_lock. The fix is to keep the
device runtime resumed while registering clks.
- Another runtime PM related deadlock, this time with disabling
unused clks during late init.
We get an ABBA deadlock where a device is runtime PM resuming (or
suspending) while the disabling of unused clks is happening in
parallel. That runtime PM action calls into the clk framework and
tries to grab the clk prepare_lock while the disabling of unused
clks holds the prepare_lock and is waiting for that runtime PM
action to complete.
The fix is to runtime resume all the clk provider devices before
grabbing the clk prepare_lock during disable unused.
- A build fix to provide an empty devm_clk_rate_exclusive_get()
function when CONFIG_COMMON_CLK=n"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: mediatek: mt7988-infracfg: fix clocks for 2nd PCIe port
clk: mediatek: Do a runtime PM get on controllers during probe
clk: Get runtime PM before walking tree for clk_summary
clk: Get runtime PM before walking tree during disable_unused
clk: Initialize struct clk_core kref earlier
clk: Don't hold prepare_lock when calling kref_put()
clk: Remove prepare_lock hold assertion in __clk_release()
clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
On x86, the ordinary, position dependent small and kernel code models
only support placement of the executable in 32-bit addressable memory,
due to the use of 32-bit signed immediates to generate references to
global variables. For the kernel, this implies that all global variables
must reside in the top 2 GiB of the kernel virtual address space, where
the implicit address bits 63:32 are equal to sign bit 31.
This means the kernel code model is not suitable for other bare metal
executables such as the kexec purgatory, which can be placed arbitrarily
in the physical address space, where its address may no longer be
representable as a sign extended 32-bit quantity. For this reason,
commit
e16c2983fb ("x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors")
switched to the large code model, which uses 64-bit immediates for all
symbol references, including function calls, in order to avoid relying
on any assumptions regarding proximity of symbols in the final
executable.
The large code model is rarely used, clunky and the least likely to
operate in a similar fashion when comparing GCC and Clang, so it is best
avoided. This is especially true now that Clang 18 has started to emit
executable code in two separate sections (.text and .ltext), which
triggers an issue in the kexec loading code at runtime.
The SUSE bugzilla fixes tag points to gcc 13 having issues with the
large model too and that perhaps the large model should simply not be
used at all.
Instead, use the position independent small code model, which makes no
assumptions about placement but only about proximity, where all
referenced symbols must be within -/+ 2 GiB, i.e., in range for a
RIP-relative reference. Use hidden visibility to suppress the use of a
GOT, which carries absolute addresses that are not covered by static ELF
relocations, and is therefore incompatible with the kexec loader's
relocation logic.
[ bp: Massage commit message. ]
Fixes: e16c2983fb ("x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors")
Fixes: https://bugzilla.suse.com/show_bug.cgi?id=1211853
Closes: https://github.com/ClangBuiltLinux/linux/issues/2016
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Fangrui Song <maskray@google.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/20240417-x86-fix-kexec-with-llvm-18-v1-0-5383121e8fb7@kernel.org/
The PLL0 is configured by the bootloader and is the parent of the
mdp_clk_src. The Trion implementation of the configure function is
already skipping this step if the PLL is enabled, so lets extend the
same behavior to Lucid Evo variant.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240418-clk-qcom-lucid-evo-skip-configuring-enabled-v1-1-caede5f1c7a3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The data-lanes are a property of the out remote endpoint, so move them
from mdss_dp3 to the mdss_dp3_out. Also add the link-frequencies to
mdss_dp3_out and make sure to include all frequencies.
Fixes: f9a9c11471 ("arm64: dts: qcom: x1e80100-qcp: Enable more support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240419-x1e80100-dts-fix-mdss-dp3-v2-3-10f4ed7a09b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The data-lanes are a property of the out remote endpoint, so move them
from mdss_dp3 to the mdss_dp3_out. Also add the link-frequencies to
mdss_dp3_out and make sure to include all frequencies.
Fixes: d7e03cce04 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240419-x1e80100-dts-fix-mdss-dp3-v2-2-10f4ed7a09b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The link-frequencies belong in mdss_dp3_out. Drop them from mdss_dp3_in.
Fixes: 1940c25eaa ("arm64: dts: qcom: x1e80100: Add display nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240419-x1e80100-dts-fix-mdss-dp3-v2-1-10f4ed7a09b4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Performance regression reported with NFS/RDMA using Omnipath,
bisected to commit e084ee673c ("svcrdma: Add Write chunk WRs to
the RPC's Send WR chain").
Tracing on the server reports:
nfsd-7771 [060] 1758.891809: svcrdma_sq_post_err:
cq.id=205 cid=226 sc_sq_avail=13643/851 status=-12
sq_post_err reports ENOMEM, and the rdma->sc_sq_avail (13643) is
larger than rdma->sc_sq_depth (851). The number of available Send
Queue entries is always supposed to be smaller than the Send Queue
depth. That seems like a Send Queue accounting bug in svcrdma.
As it's getting to be late in the 6.9-rc cycle, revert this commit.
It can be revisited in a subsequent kernel release.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218743
Fixes: e084ee673c ("svcrdma: Add Write chunk WRs to the RPC's Send WR chain")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
The IP core only has breaking changes when there major version changes.
Hence, only match the major number. This is also in line with the other
core ADI has upstream. The current check for erroring out
'expected_version > current_version"' is then wrong as we could just
increase the core major with breaking changes and that would go
unnoticed.
Fixes: ef04070692 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-ad9467-new-features-v1-2-3e7628ff6d5e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
struct Scsi_Host private data contains pointer to struct ctlr_info.
Restore allocation of only 8 bytes to store pointer in struct Scsi_Host
private data area.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: bbbd254991 ("scsi: hpsa: Fix allocation size for scsi_host_alloc()")
Signed-off-by: Yuri Karpov <YKarpov@ispras.ru>
Link: https://lore.kernel.org/r/20240312170447.743709-1-YKarpov@ispras.ru
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sparse reports:
fs/xfs/xfs_log_cil.c:1127:1: warning: context imbalance in 'xlog_cil_push_work' - different lock contexts for basic block
fs/xfs/xfs_log_cil.c:1380:1: warning: context imbalance in 'xlog_cil_push_background' - wrong count at exit
fs/xfs/xfs_log_cil.c:1623:9: warning: context imbalance in 'xlog_cil_commit' - unexpected unlock
xlog_cil_push_background() has a locking annotations for an rw_sem.
Sparse does not track lock contexts for rw_sems, so the
annotation generates false warnings. Remove the annotation.
xlog_wait_on_iclog() drops the log->l_ic_loglock. The function has a
sparse annotation, but the prototype in xfs_log_priv.h does not.
Hence the warning from xlog_cil_push_work() which calls
xlog_wait_on_iclog(). Add the missing annotation.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
The AD9739A is a 14-bit, 2.5 GSPS high performance RF DACs that are capable
of synthesizing wideband signals from DC up to 3 GHz.
A dual-port, source synchronous, LVDS interface simplifies the digital
interface with existing FGPA/ASIC technology. On-chip controllers are used
to manage external and internal clock domain variations over temperature to
ensure reliable data transfer from the host to the DAC core.
Co-developed-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-10-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support the Analog Devices Generic AXI DAC IP core. The IP core is used
for interfacing with digital-to-analog (DAC) converters that require either
a high-speed serial interface (JESD204B/C) or a source synchronous parallel
interface (LVDS/CMOS). Typically (for such devices) SPI will be used for
configuration only, while this IP core handles the streaming of data into
memory via DMA.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-9-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds the needed backend ops for supporting a backend inerfacing
with an high speed dac. The new ops are:
* data_source_set();
* set_sampling_freq();
* extend_chan_spec();
* ext_info_set();
* ext_info_get().
Also to note the new helpers that are meant to be used by the backends
when extending an IIO channel (adding extended info):
* iio_backend_ext_info_set();
* iio_backend_ext_info_get().
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-8-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the iio_dma_buffer_write() and iio_dma_buffer_space_available()
functions provided by the buffer-dma core, to enable write support in
the buffer-dmaengine code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-5-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the devm_iio_dmaengine_buffer_setup() function to support
specifying the buffer direction.
Update the iio_dmaengine_buffer_submit() function to handle input
buffers as well as output buffers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-4-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As of commit 7d1d865181 ("[SCSI] libsas: fix false positive 'device
attached' conditions"), reset the phy->entacted_sas_addr address to a
zero-address when the link rate is less than 1.5G.
Currently we find that when a new device is attached, and the link rate is
less than 1.5G, but the device type is not NO_DEVICE, for example: the link
rate is SAS_PHY_RESET_IN_PROGRESS and the device type is stp. After setting
the phy->entacted_sas_addr address to the zero address, the port will
continue to be created for the phy with the zero-address, and other phys
with the zero-address will be tried to be added to the new port:
[562240.051197] sas: ex 500e004aaaaaaa1f phy19:U:0 attached: 0000000000000000 (no device)
// phy19 is deleted but still on the parent port's phy_list
[562240.062536] sas: ex 500e004aaaaaaa1f phy0 new device attached
[562240.062616] sas: ex 500e004aaaaaaa1f phy00:U:5 attached: 0000000000000000 (stp)
[562240.062680] port-7:7:0: trying to add phy phy-7:7:19 fails: it's already part of another port
Therefore, it should be the same as sas_get_phy_attached_dev(). Only when
device_type is SAS_PHY_UNUSED, sas_address is set to the 0 address.
Fixes: 7d1d865181 ("[SCSI] libsas: fix false positive 'device attached' conditions")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240312141103.31358-5-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found that when ex_phy was attached and added to the parent wide port,
ex_phy->port was not set, resulting in sas_unregister_devs_sas_addr() not
calling sas_port_delete_phy() when deleting the phy, and the deleted phy
was still on the parent wide port's phy_list.
When we use sas_port_add_ex_phy() to set ex_phy->port to solve the above
problem, we find that after all the phys of the parent_port are removed and
the number of phy becomes 0, the parent_port will not be set to NULL. This
causes the freed parent port to be used when attaching a new ex_phy in
sas_ex_add_parent_port().
Use sas_port_add_ex_phy() instead of sas_port_add_phy() to set ex_phy->port
when ex_phy is added to the parent port, and set ex_dev->parent_port to
NULL when the number of phy on the port becomes 0.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240312141103.31358-4-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move sas_add_parent_port() to sas_expander.c and rename it to
sas_ex_add_parent_port() as it is only used in this file.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240312141103.31358-3-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This moves the process of adding ex_phy to a port into a new helper.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20240312141103.31358-2-yangxingui@huawei.com
Reviewed-by: John Garry <john.g.garry@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adding write support to the buffer-dma code is easy - the write()
function basically needs to do the exact same thing as the read()
function: dequeue a block, read or write the data, enqueue the block
when entirely processed.
Therefore, the iio_buffer_dma_read() and the new iio_buffer_dma_write()
now both call a function iio_buffer_dma_io(), which will perform this
task.
Note that we preemptively reset block->bytes_used to the buffer's size
in iio_dma_buffer_request_update(), as in the future the
iio_dma_buffer_enqueue() function won't reset it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-3-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change its name to iio_dma_buffer_usage(), as this function can be used
both for the .data_available and the .space_available callbacks.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-2-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This brings the DMA buffer API more in line with what we have in the
triggered buffer. There's no need of having both
devm_iio_dmaengine_buffer_setup() and devm_iio_dmaengine_buffer_alloc().
Hence we introduce the new iio_dmaengine_buffer_setup() that together
with devm_iio_dmaengine_buffer_setup() should be all we need.
Note that as part of this change iio_dmaengine_buffer_alloc() is again
static and the axi-adc was updated accordingly.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240419-iio-backend-axi-dac-v4-1-5ca45b4de294@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Both functions `dps310_get_pres_precision` and
`dps310_get_temp_precision` provide the oversampling rate by calling the
`BIT()` macro. However, to look up the corresponding scale factor, we
need the register value itself. Currently, this is achieved by undoing
the calculation of the oversampling rate with `ilog2()`.
Simplify the two functions for getting the scale factor and directly
use the register content for the lookup.
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-5-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align error handling with `dps310_calculate_temp`, where it's not
possible to differentiate between errors and valid calculations by
checking if the returned value is negative.
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-3-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current implementation interprets negative values returned from
`dps310_calculate_temp` as error codes.
This has a side effect that when negative temperature values are
calculated, they are interpreted as error.
Fix this by using the return value only for error handling and passing a
pointer for the value.
Fixes: ba6ec48e76 ("iio: Add driver for Infineon DPS310")
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240415105030.1161770-2-thomas.haemmerle@leica-geosystems.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We currently insist on disabling PAuth on vcpu_load(), and get to
enable it on first guest use of an instruction or a key (ignoring
the NV case for now).
It isn't clear at all what this is trying to achieve: guests tend
to use PAuth when available, and nothing forces you to expose it
to the guest if you don't want to. This also isn't totally free:
we take a full GPR save/restore between host and guest, only to
write ten 64bit registers. The "value proposition" escapes me.
So let's forget this stuff and enable PAuth eagerly if exposed to
the guest. This results in much simpler code. Performance wise,
that's not bad either (tested on M2 Pro running a fully automated
Debian installer as the workload):
- On a non-NV guest, I can see reduction of 0.24% in the number
of cycles (measured with perf over 10 consecutive runs)
- On a NV guest (L2), I see a 2% reduction in wall-clock time
(measured with 'time', as M2 doesn't have a PMUv3 and NV
doesn't support it either)
So overall, a much reduced complexity and a (small) performance
improvement.
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-16-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that we (hopefully) correctly handle ERETAx, drop the masking
of the PAuth feature (something that was not even complete, as
APA3 and AGA3 were still exposed).
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-15-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that we have some emulation in place for ERETA[AB], we can
plug it into the exception handling machinery.
As for a bare ERET, an "easy" ERETAx instruction is processed as
a fixup, while something that requires a translation regime
transition or an exception delivery is left to the slow path.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-14-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
FEAT_NV has the interesting property of relying on ERET being
trapped. An added complexity is that it also traps ERETAA and
ERETAB, meaning that the Pointer Authentication aspect of these
instruction must be emulated.
Add an emulation of Pointer Authentication, limited to ERETAx
(always using SP_EL2 as the modifier and ELR_EL2 as the pointer),
using the Generic Authentication instructions.
The emulation, however small, is placed in its own compilation
unit so that it can be avoided if the configuration doesn't
include it (or the toolchan in not up to the task).
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-13-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Pointer Authentication comes in many flavors, and a faithful emulation
relies on correctly handling the flavour implemented by the HW.
For this, provide a new kvm_has_pauth() that checks whether we
expose to the guest a particular level of support. This checks
across all 3 possible authentication algorithms (Q5, Q3 and IMPDEF).
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-12-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order for a L1 hypervisor to correctly handle PAuth instructions,
it must observe traps caused by a L1 PAuth instruction when
HCR_EL2.API==0. Since we already handle the case for API==1 as
a fixup, only the exception injection case needs to be handled.
Rework the kvm_handle_ptrauth() callback to reinject the trap
in this case. Note that APK==0 is already handled by the exising
triage_sysreg_trap() helper.
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-11-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Although KVM couples API and APK for simplicity, the architecture
makes no such requirement, and the two can be independently set or
cleared.
Check for which of the two possible reasons we have trapped here,
and if the corresponding L1 control bit isn't set, delegate the
handling for forwarding.
Otherwise, set this exact bit in HCR_EL2 and resume the guest.
Of course, in the non-NV case, we keep setting both bits and
be done with it. Note that the entry core already saves/restores
the keys should any of the two control bits be set.
This results in a bit of rework, and the removal of the (trivial)
vcpu_ptrauth_enable() helper.
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-10-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
If the L1 hypervisor decides to trap ERETs while running L2,
make sure we don't try to emulate it, just like we wouldn't
if it had its NV bit set.
The exception will be reinjected from the core handler.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-9-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
A significant part of the FEAT_NV extension is to trap ERET
instructions so that the hypervisor gets a chance to switch
from a vEL2 L1 guest to an EL1 L2 guest.
But this also has the unfortunate consequence of trapping ERET
in unsuspecting circumstances, such as staying at vEL2 (interrupt
handling while being in the guest hypervisor), or returning to host
userspace in the case of a VHE guest.
Although we already make some effort to handle these ERET quicker
by not doing the put/load dance, it is still way too far down the
line for it to be efficient enough.
For these cases, it would ideal to ERET directly, no question asked.
Of course, we can't do that. But the next best thing is to do it as
early as possible, in fixup_guest_exit(), much as we would handle
FPSIMD exceptions.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-8-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Honor the trap forwarding bits for both ERET and SMC, using a new
helper that checks for common conditions.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Co-developed-by: Jintack Lim <jintack.lim@linaro.org>
Signed-off-by: Jintack Lim <jintack.lim@linaro.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-7-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the HCR_EL2 configuration for FEAT_NV2, adding the required
bits for running a guest hypervisor, and overall merging the
allowed bits provided by the guest.
This heavily replies on unavaliable features being sanitised
when the HCR_EL2 shadow register is accessed, and only a couple
of bits must be explicitly disabled.
Non-NV guests are completely unaffected by any of this.
Reviewed-by: Joey Gouly <joey.gouly@arm.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240419102935.1935571-6-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>