We can get HDMI working as long as the 5V regulator is on. There is
probably an encoder chip there too, but so far no idea what it might be.
Let's keep the 5V HDMI regulator always enabled for now as otherwise we
cannot detect the monitor properly.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add tmp105 sensor for droid 4. This can be used with modprobe
lm75.ko and running sensors from lm-sensors package. Note that
the lm75.c driver does not yet support alert interrupt but
droid 4 seems to be wired for it.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Droid 4 has a GPIO line that we can use with CONFIG_POWER_RESET_GPIO.
It is probably connected to the CPCAP PMIC, and seems to power down
the whole device taking power consumption to zero based on what
I measured.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI LMU driver has not yet been merged, but the device
tree binding for TI LMU drivers has been acked already
earlier by Rob Herring <robh+dt@kernel.org>. So it should
be safe to apply to cut down the number of pending patches.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit enable DMA-based transfers for SD/eMMC card adapters
and reduce number of interrupts produced by SD-card/eMMC-card
adapters.
Sometimes interrupts from SD-card/eMMC-card adapters running in
PIO mode blocks execution of hrtimers and I2S DMA callbacks for
a long periods (100 ms or more).
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
[moved dma properties to rk3xxx.dtsi and added sdio dma]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that we're applying the IOMMU API reserved regions to our IOVA
domains, we shouldn't need to privately special-case PCI windows, or
indeed anything else which isn't specific to our iommu-dma layer.
However, since those aren't IOMMU-specific either, rather than start
duplicating code into IOMMU drivers let's transform the existing
function into an iommu_get_resv_regions() helper that they can share.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Now that it's simple to discover the necessary reservations for a given
device/IOMMU combination, let's wire up the appropriate handling. Basic
reserved regions and direct-mapped regions we simply have to carve out
of IOVA space (the IOMMU core having already mapped the latter before
attaching the device). For hardware MSI regions, we also pre-populate
the cookie with matching msi_pages. That way, irqchip drivers which
normally assume MSIs to require mapping at the IOMMU can keep working
without having to special-case their iommu_dma_map_msi_msg() hook, or
indeed be aware at all of quirks preventing the IOMMU from translating
certain addresses.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Even if a host controller's CPU-side MMIO windows into PCI I/O space do
happen to leak into PCI memory space such that it might treat them as
peer addresses, trying to reserve the corresponding I/O space addresses
doesn't do anything to help solve that problem. Stop doing a silly thing.
Fixes: fade1ec055 ("iommu/dma: Avoid PCI host bridge windows")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.
For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.
Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.
Fixes: d30ddcaa7b ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This makes the example more or less correspond with the da850-evm
hardware setup.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The examples have been copied from the DT with whitespace errors. Fix
them.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The vpif display driver uses a static i2c adapter ID of 1 but on the
da850-evm board in DT boot mode the i2c adapter ID is actually 0.
Make the adapter ID configurable like it already is for vpif capture.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, building code which uses the API guarded by the IOMMU_IOVA
will fail to link if IOMMU_IOVA is not enabled. Often this code will be
using the API provided by the IOMMU_API Kconfig symbol, but support for
this can be optional, with code falling back to contiguous memory. This
commit implements dummy functions for the IOVA API so that it can be
compiled out.
With both IOMMU_API and IOMMU_IOVA optional, code can now be built with
or without support for IOMMU without having to resort to #ifdefs in the
user code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The linux/iommu.h and linux/iova.h headers belong to the IOMMU subsystem
but scripts/get_maintainers.pl currently fails to assign them because
they aren't listed in MAINTAINERS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9 ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b3 ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There is already helper functions to do 64-bit I/O on 32-bit machines or
buses, thus we don't need to reinvent the wheel.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Usual pattern when we check for return code, which might be negative
errno, is either (ret) or (!ret).
Remove extra ' != 0' from condition.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There is no need to assign ret to 0 in some cases. Moreover it might
shadow some errors in the future.
Remove such assignments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There is no need to have a temporary variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There is inconsistency in return codes across the functions called from
detect_intel_iommu().
Make it consistent and propagate return code to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It's no longer necessary to keep the i2c_client in the device struct
unmodified until a sensor is found, so reduce stack usage in
em28xx_probe_sensor_micron() and em28xx_probe_sensor_omnivision() by using
a pointer to the client instead of a local copy.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC documentation added two sections on the main media kAPI level.
There should be only one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1296:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All remaining soc-camera drivers use videobuf2, drop support for
videobuf1.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: also drop 'select VIDEOBUF_GEN' from Kconfig]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VPU firmware has a bug and may return invalid buffer index for
some vp9 videos. Check the buffer indexes before accessing the
buffer.
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Acked-by: Tiffany Lin <Tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include <linux/slab.h> to fix these build errors:
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c: In function 'mtk_jpeg_open':
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1017:2: error: implicit declaration of function 'kzalloc' [-Werror=implicit-function-declaration]
ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1017:6: warning: assignment makes pointer from integer without a cast [enabled by default]
ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
../drivers/media/platform/mtk-jpeg/mtk_jpeg_core.c:1047:2: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
kfree(ctx);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ming Hsiu Tsai <minghsiu.tsai@mediatek.com>
Cc: Rick Chang <rick.chang@mediatek.com>
Cc: Bin Liu <bin.liu@mediatek.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously multiple calls to v4l2_device_register_subdev_nodes() ended up
corrupting memory and leaking some, too. This patch changes the behaviour so
that sub-devices the device nodes of which are already registered are
ignored.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Skipping, which is sometimes used in terminology related to sensors when
referring to sub-sampling is replaced by more suitable sub-sampling
instead. Skipping is retained in a note in parentheses.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
After this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
alias: of:N*T*Ctoshiba,et8ek8C*
alias: of:N*T*Ctoshiba,et8ek8
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Feature Abort shouldn't be sent in reply to messages from Unregistered,
since that would make it a broadcast message.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When validating the struct cec_s_log_addrs input a debug message is printed
for all except two of the 'return -EINVAL' paths.
Also log the reason for the missing two paths.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several error paths didn't log why an error was returned. Add this.
Also handle the corner case of "adapter is unconfigured AND the message
is from Unregistered to TV AND reply is non-zero" separately and return
EINVAL in that case, since it really is an invalid value and not an
unconfigured CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardcoded function name is actually wrong. Use __func__ instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even when the CEC device is unconfigured due to an invalid physical
address it is still allowed to send a message from 0xf (Unregistered)
to 0 (TV). This is a corner case explicitly allowed by the CEC specification.
Document this corner case.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document all the various error codes returned by the CEC ioctls.
These were never documented, instead the documentation relied on a reference
to the generic error codes, but that's not sufficient.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC_TRANSMIT ioctl now returns -EPERM if an attempt is made to
transmit a message for an unconfigured adapter (i.e. userspace
never called CEC_ADAP_S_LOG_ADDRS).
This differentiates this case from when LAs are configured, but no
physical address is set. In that case -ENONET is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC specifications explicitly allows you to send poll messages and
Image/Text View On messages to a TV, even when unconfigured (i.e. there is
no hotplug signal detected). Some TVs will pull the HPD low when switching
to another input, or when going into standby, but CEC should still be
allowed to wake up such a display.
Add support for sending messages with initiator 0xf (Unregistered) and
destination 0 (TV) when no physical address is present.
This also required another change: the CEC adapter has to stay enabled as
long as 1) the CEC device is configured or 2) at least one filehandle is open
for the CEC device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the adapter is unloaded or unconfigured, then all transmits and
pending waits should be flushed.
Move this code into its own function and improve the code that cancels
delayed work to avoid having to unlock adap->lock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the length of the modalias is greater than the buffer size, then the
modalias is truncated. However the untruncated length is returned which
will cause an error. Fix this to return the truncated length. If an error
in the case was desired, then then we should just return -ENOMEM.
The reality is no device will ever have 4KB of compatible strings to hit
this case.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Fixed a few spelling mistakes, but mostly incorrect rst syntax that caused wrong
references or font style.
No actual documentation changes, just fixes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
vivid_try_fmt_vid_cap() called tpg_calc_line_width to calculate the sizeimage
value, but that tpg function uses the current format, not the proposed (tried)
format.
Rewrote this code to calculate this correctly.
The vivid_try_fmt_vid_out() code was completely wrong w.r.t. sizeimage, and
neither did it take the vdownsampling[] factors into account.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
