hidg->req should be accessed only with write_spinlock held as it is
set to NULL when we get disabled by host.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove pointer dereference after free.
Addresses-Coverity-ID: 1091173
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB3.0 Specification "Table 9-20. Standard Endpoint Descriptor",
for interrupt and isochronous endpoints, wMaxPacketSize must be set to
1024 if the endpoint defines bMaxBurst to be greater than zero.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The rk3328 i2c is the same as rk3399
Signed-off-by: Liang Chen <cl@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Basic support for MT7620 built-in wireless radio was added to
OpenWrt in r41441. It has seen some heavy cleaning and refactoring
since in order to match the Kernel's code quality standards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: a1030e92c1 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device")
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cherrytrail devices use the dw i2c-bus with uid 7 to access their PMIC.
Even if the i2c-bus to the PMIC is not shared with the SoC's P-Unit
and i2c-designware-baytrail.c thus does not set the pm_disabled flag,
we still need to disable pm so that ACPI PMIC opregions can access the
PMIC during late-suspend and early-resume.
This fixes errors like these blocking suspend:
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently we are already setting a pm_runtime_disabled flag and disabling
runtime-pm for i2c-busses used for accessing the system PMIC on x86.
But this is not enough, there are ACPI opregions which may want to access
the PMIC during late-suspend and early-resume, so we need to completely
disable pm to be safe.
This commit renames the flag from pm_runtime_disabled to pm_disabled and
adds the following new behavior if the flag is set:
1) Call dev_pm_syscore_device(dev, true) which disables normal suspend /
resume and remove the pm_runtime_disabled check from dw_i2c_plat_resume
since that will now never get called. This fixes suspend_late handlers
which use ACPI PMIC opregions causing errors like these:
PM: Suspending system (freeze)
PM: suspend of devices complete after 1127.751 msecs
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
2) Set IRQF_NO_SUSPEND irq flag. This fixes resume_early handlers which
handlers which use ACPI PMIC opregions causing errors like these:
PM: resume from suspend-to-idle
i2c_designware 808622C1:06: controller timed out
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This just deletes the Moxa ART driver and replaces it with the
more versatile Faraday FTGPIO010 driver.
Make this default on for ARCH_GEMINI and ARCH_MOXART so we do
not get Kconfig glitches.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our testing shows the semaphore failing to be transferred on CherryTrail
in about 0.5% of all cases. The existing timeout needs to be lengthened
to accommodate the worst cases.
V2: Rebased on https://cgit.freedesktop.org/drm-intel/commit/?h=topic/designware-baytrail
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Gemini driver is actually a driver for the Faraday Technology
FTGPIO010 IP block. We rename the driver and the Kconfig symbol and
put in a a new compatible string for the Moxa ART SoC that is also
using this IP block.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DT bindings assumed that this IP block was coming from
Cortina Systems, which turns out not to be true. It is a
standard IP block from Faraday Technology and also used in the
Moxa moxart SoC.
We augment the bindings to cover all existing parts and rename
it after the IP block. This involves deleting the old Moxa
bindings that now are contained in this binding.
Cc: devicetree@vger.kernel.org
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull immutable branch as a common base for further development:
"Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix."
According to [0] pointed out by Marc Zyngier in a report about a
similar error message, PPIs 11 and 13 are edge triggered on
Cortex-A9 socs including the rk3066 and rk3188 which currently
mark them as level triggered.
Until some time ago the gic did not care but commit 992345a58e
("irqchip/gic: WARN if setting the interrupt type for a PPI fails")
introduced a warning for that case.
Fix the warning on these socs by describing the interrupts correctly
and also using the binding constants for easier reading in the future.
[0] http://infocenter.arm.com/help/topic/com.arm.doc.ddi0407f/CCHEIGIC.html
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Back in commit:
92b0729c34 ("x86/mm, x86/mce: Add memcpy_mcsafe()")
... I made a copy/paste error setting up the exception table entries
and ended up with two for label .L_cache_w3 and none for .L_cache_w2.
This means that if we take a machine check on:
.L_cache_w2: movq 2*8(%rsi), %r10
then we don't have an exception table entry for this instruction
and we can't recover.
Fix: s/3/2/
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 92b0729c34 ("x86/mm, x86/mce: Add memcpy_mcsafe()")
Link: http://lkml.kernel.org/r/1490046030-25862-1-git-send-email-tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is no need for the __ASSEMBLY__ ifdefery anymore since the
architecture level set code that deals with facility bits was
converted to C in the meantime.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the actual size of the facility list array within the lowcore
structure for the MAX_FACILITY_BIT define instead of a comment which
states what this is good for. This makes it a bit harder to break
things.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide the remaining stsi information via debugfs files. This also
might be useful for debugging purposes.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide the raw stsi 15,1,x data contents via debugfs. This makes it
much easier to debug unexpected scheduling domains on machines that
provide cpu topology information.
Therefore this file adds a new 's390/stsi' debugfs directory with a
file for each possible topology nesting level that is allowed by the
architecture. The files will be created regardless if the machine
supports all, or any, level. If a level is not supported, or no data
is available, user space can recognize this with a -EINVAL error code
when trying to read such data.
In addition a 'topology' symlink is created that points to the file
that contains the data that is used to create the scheduling domains.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a top-level 's390' directory which should be used when
adding new s390 specific debug feature files and/or directories.
This makes hopefully sure that the contents of the s390 directory will
be a bit more structured. Right now we have a couple of top-level
files where it is not easy to tell to which subsystem they belong to.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
User space needs some information about the secure key(s)
before actually invoking the pkey and/or paes funcionality.
This patch introduces a new ioctl API and in kernel API to
verify the the secure key blob and give back some
information about the key (type, bitsize, old MKVP).
Both APIs are described in detail in the header files
arch/s390/include/asm/pkey.h and arch/s390/include/uapi/asm/pkey.h.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If running within a level 3 hypervisor, the hypervisor provides a
SYSIB block which contains a control program indentifier string. Use
this string instead of the simple KVM and z/VM strings only. In case
of z/VM this provides addtional information: the z/VM version.
The new string looks similar to this:
Hardware name: IBM 2964 N96 702 (z/VM 6.4.0)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The arch description provided for the "Hardware name:" contains lots
of extra whitespace due to the way the SYSIB contents are defined
(strings aren't zero terminated).
This looks a bit odd and therefore remove the extra whitespace
characters. This also gives the opportunity to add more information,
if required, without hitting the magic 80 characters per line limit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow compiler warnings again for the sysinfo file. Compiler warnings
were disabled when the bogomips calculation with math-emu code was
introduced ("[S390] Calibrate delay and bogomips.").
Since that code is gone, we can enable warnings again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use MACHINE_FLAG_TOPOLOGY instead of MACHINE_HAS_TOPOLOGY when
clearing the bit that indicates if the machine provides topology
information (and if it should be used). Currently works anyway.
Fixes: 68cc795d19 ("s390/topology: make "topology=off" parameter work")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use a single long value instead of a single element array to represent
the core mask. The array is a leftover from 32/31 bit code so we were
able to use bitops helper functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 specific little endian bitop macros are gone since a long time.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__GFP_REPEAT has a rather weak semantic but since it has been introduced
around 2.6.12 it has been ignored for low order allocations.
page_table_alloc then uses the flag for a single page allocation. This
means that this flag has never been actually useful here because it has
always been used only for PAGE_ALLOC_COSTLY requests.
An earlier attempt to remove the flag 10d58bf297 ("s390: get rid of
superfluous __GFP_REPEAT") has missed this one but the situation is very
same here.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new line to /proc/cpuinfo which shows all available facilities
as reported by the stfle instruction:
> cat /proc/cpuinfo
...
facilities : 0 1 2 3 4 6 7 ...
...
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same helper function like for_each_set_bit in generic code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a secure key with an old Master Key Verification
Pattern was given to the pkey_findcard function, there was
no responsible card found because only the current MKVP of
each card was compared. With this fix also the old MKVP
values are considered and so a matching card able to handle
the key is reported back to the caller.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit af51160ebd ("s390/smp: initialize cpu_present_mask in
setup_arch") initializes the cpu_present_mask much earlier than
before. However the cpu detection code relies on the fact that iff
logical cpu 0 is marked present then also the corresponding physical
cpu address within the pcpu_devices array slot is valid.
Since commit 44fd22992c ("[PATCH] Register the boot-cpu in the cpu
maps earlier") this assumption is not true anymore. The patch marks
logical cpu 0 as present in common code without that architecture code
had a chance to setup the logical to physical map.
With that change the cpu detection code assumes that the physical cpu
address of cpu 0 is also 0, which is not necessarily true.
Subsequently the physical cpu address of the ipl cpu will be mapped to
a different logical cpu. If that cpu is brought online later the ipl
cpu will send itself an initial cpu reset sigp signal. This in turn
completely resets the ipl cpu and the system stops working.
A dump of such a system looks like a "store status" has been
forgotten. But actually the kernel itself removed all traces which
would allow to easily tell what went wrong.
To fix this initialize the logical to physical cpu address already in
smp_setup_processor_id(). In addition remove the initialization of the
cpu_present_mask and cpu_online_mask for cpu 0, since that has already
been done. Also add a sanity check, just in case common code will be
changed again...
The problem can be easily reproduced within a z/VM guest:
> chcpu -d 0
> vmcp ipl
Fixes: af51160ebd ("s390/smp: initialize cpu_present_mask in setup_arch")
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reorder the operations in decompress_kernel() to ensure initrd is moved
to a safe location before the bss section is zeroed.
During decompression bss can overlap with the initrd and this can
corrupt the initrd contents depending on the size of the compressed
kernel (which affects where the initrd is placed by the bootloader) and
the size of the bss section of the decompressor.
Also use the correct initrd size when checking for overlaps with
parmblock.
Fixes: 06c0dd72ae ([S390] fix boot failures with compressed kernels)
Cc: stable@vger.kernel.org
Reviewed-by: Joy Latten <joy.latten@canonical.com>
Reviewed-by: Vineetha HariPai <vineetha.hari.pai@canonical.com>
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Unfortunately the HWMON_T_ALARM define was missing,
although the associated entry was present in hwmon_temp_attributes.
This is needed to convert drivers to the new interface which use channel
based alarms.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8705F is known to respond on both SIO addresses. Registering it twice
may result in system lockups.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e84bd9535e ("hwmon: (it87) Add support for second Super-IO chip")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Traced fans not spinning to incorrect PWM value being written.
The passed in value was written instead of the calulated value.
Fixes: 54187ff9d7 ("hwmon: (max31790) Convert to use new hwmon registration API")
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The OPP are declared as shared but no operating points are declared for
cpu1, 2 and 3. Thus, the following error happens during the boot:
cpu cpu1: dev_pm_opp_of_get_sharing_cpus: Couldn't find tcpu_dev node.
This patch applies the operating points to each cpu of the A33.
Fixes: 03749eb88e ("ARM: dts: sun8i: add opp-v2 table for A33")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds a new system call to enable the use of guarded storage for
user space processes. The system call takes two arguments, a command
and pointer to a guarded storage control block:
s390_guarded_storage(int command, struct gs_cb *gs_cb);
The second argument is relevant only for the GS_SET_BC_CB command.
The commands in detail:
0 - GS_ENABLE
Enable the guarded storage facility for the current task. The
initial content of the guarded storage control block will be
all zeros. After the enablement the user space code can use
load-guarded-storage-controls instruction (LGSC) to load an
arbitrary control block. While a task is enabled the kernel
will save and restore the current content of the guarded
storage registers on context switch.
1 - GS_DISABLE
Disables the use of the guarded storage facility for the current
task. The kernel will cease to save and restore the content of
the guarded storage registers, the task specific content of
these registers is lost.
2 - GS_SET_BC_CB
Set a broadcast guarded storage control block. This is called
per thread and stores a specific guarded storage control block
in the task struct of the current task. This control block will
be used for the broadcast event GS_BROADCAST.
3 - GS_CLEAR_BC_CB
Clears the broadcast guarded storage control block. The guarded-
storage control block is removed from the task struct that was
established by GS_SET_BC_CB.
4 - GS_BROADCAST
Sends a broadcast to all thread siblings of the current task.
Every sibling that has established a broadcast guarded storage
control block will load this control block and will be enabled
for guarded storage. The broadcast guarded storage control block
is used up, a second broadcast without a refresh of the stored
control block with GS_SET_BC_CB will not have any effect.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The calculation of the global physical address (GPA) on UV4 is
incorrect. The gnode_extra/upper global offset should only be
applied for fixed address space systems (UV1..3).
Tested-by: John Estabrook <john.estabrook@hpe.com>
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: John Estabrook <estabrook@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170321231646.667689538@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
pgprot_dmachoerent() is not defined on every architecture. Having
COMPILE_TEST set for the driver causes it to be compiled on
architectures which do not have pgprot_dmachoerent():
drivers/misc/aspeed-lpc-ctrl.c: In function 'aspeed_lpc_ctrl_mmap':
drivers/misc/aspeed-lpc-ctrl.c:51:9: error: implicit declaration of
function 'pgprot_dmacoherent' [-Werror=implicit-function-declaration]
prot = pgprot_dmacoherent(prot);
There are two possible solutions:
1. Remove COMPILE_TEST to ensure the driver is only compiled on ARM
2. Use pgprot_noncached() instead of pgprot_dmachoerent()
The first option results in less compile testing of the LPC control
driver which is undesirable.
The second option uses a function that is declared on all architectures
and therefore should always build. Currently there is no practical
difference between pgprot_noncached() and pgprot_dmachoerent() for the
aspeed chips that this driver is compatible with. The reason for
pgprot_dmachoerent() was that there may be chips made at some point in
the future that could include hardware that pgprot_dmachoerent() could
optimise for. As none of this hardware has even been announced there
isn't really a need for pgprot_dmachoerent().
Using pgprot_noncached() is completely correct and optimal for all
existing hardware on which the LPC control driver will run.
This commit also addresses that phys_addr_t should be printed using %pap
rather than %x:
In file included from include/linux/miscdevice.h:6:0,
from drivers/misc/aspeed-lpc-ctrl.c:11:
drivers/misc/aspeed-lpc-ctrl.c: In function 'aspeed_lpc_ctrl_probe':
drivers/misc/aspeed-lpc-ctrl.c:232:17: warning: format '%x' expects
argument of type 'unsigned int', but argument 3 has type 'phys_addr_t
{aka long long unsigned int}' [-Wformat=]
dev_info(dev, "Loaded at 0x%08x (0x%08x)\n",
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my previous Commit ab9da627906a ("drm/i915: make context status
notifier head be per engine") rely on scheduler->current_workload[x]
to distinguish gvt spacial request from i915 request. But this is
not always true since no synchronization between workload_thread and
lrc irq handler.
lrc irq handler workload_thread
---- ----
pick i915 requests;
intel_vgpu_submit_execlist();
current_workload[x] = xxx;
shadow_context_status_change();
Then current_workload[x] is not null but current request is of i915 self.
So instead we check ctx flag CONTEXT_FORCE_SINGLE_SUBMISSION. Only gvt
request set this flag and always set.
v2: Reverse the order of multi-condition 'if' statement.
Fixes: ab9da6279 ("drm/i915: make context status notifier head be per engine")
Signed-off-by: Changbin Du <changbin.du@intel.com>
Reviewed-by: Yulei Zhang <yulei.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The memory size of f2fs_stat_info also should be calculated.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
