"gmac" node stands for just an ordinary Ethernet controller,
which is by no means a provider of interrupts, i.e. it doesn't serve
as an interrupt controller, thus "#interrupt-cells" property doesn't
belong to it and so we remove it.
Fixes:
------------>8------------
DTC arch/arc/boot/dts/hsdk.dtb
arch/arc/boot/dts/hsdk.dts:207.23-235.5: Warning (interrupt_provider): /soc/ethernet@8000: '#interrupt-cells' found, but node is not an interrupt provider
arch/arc/boot/dts/hsdk.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
------------>8------------
Reported-by: Vineet Gupta <vgupta@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
- Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure where KVM
would allow userspace to refresh the cache with a bogus GPA. The bug has
existed for quite some time, but was exposed by a new sanity check added in
6.9 (to ensure a cache is either GPA-based or HVA-based).
- Drop an unused param from gfn_to_pfn_cache_invalidate_start() that got left
behind during a 6.9 cleanup.
- Disable support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken and can leak host LBRs to the guest.
- Fix a bug where KVM neglects to set the enable bits for general purpose
counters in PERF_GLOBAL_CTRL when initializing the virtual PMU. Both Intel
and AMD architectures require the bits to be set at RESET in order for v2
PMUs to be backwards compatible with software that was written for v1 PMUs,
i.e. for software that will never manually set the global enables.
- Disable LBR virtualization on CPUs that don't support LBR callstacks, as
KVM unconditionally uses PERF_SAMPLE_BRANCH_CALL_STACK when creating the
virtual LBR perf event, i.e. KVM will always fail to create LBR events on
such CPUs.
- Fix a math goof in x86's hugepage logic for KVM_SET_MEMORY_ATTRIBUTES that
results in an array overflow (detected by KASAN).
- Fix a flaw in the max_guest_memory selftest that results in it exhausting
the supply of ucall structures when run with more than 256 vCPUs.
- Mark KVM_MEM_READONLY as supported for RISC-V in set_memory_region_test.
- Fix a bug where KVM incorrectly thinks a TDP MMU root is an indirect shadow
root due KVM unnecessarily clobbering root_role.direct when userspace sets
guest CPUID.
- Fix a dirty logging bug in the where KVM fails to write-protect TDP MMU
SPTEs used for L2 if Page-Modification Logging is enabled for L1 and the L1
hypervisor is NOT using EPT (if nEPT is enabled, KVM doesn't use the TDP MMU
to run L2). For simplicity, KVM always disables PML when running L2, but
the TDP MMU wasn't accounting for root-specific conditions that force write-
protect based dirty logging.
-----BEGIN PGP SIGNATURE-----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=0hRN
-----END PGP SIGNATURE-----
Merge tag 'kvm-x86-fixes-6.9-rcN' of https://github.com/kvm-x86/linux into HEAD
- Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure where KVM
would allow userspace to refresh the cache with a bogus GPA. The bug has
existed for quite some time, but was exposed by a new sanity check added in
6.9 (to ensure a cache is either GPA-based or HVA-based).
- Drop an unused param from gfn_to_pfn_cache_invalidate_start() that got left
behind during a 6.9 cleanup.
- Disable support for virtualizing adaptive PEBS, as KVM's implementation is
architecturally broken and can leak host LBRs to the guest.
- Fix a bug where KVM neglects to set the enable bits for general purpose
counters in PERF_GLOBAL_CTRL when initializing the virtual PMU. Both Intel
and AMD architectures require the bits to be set at RESET in order for v2
PMUs to be backwards compatible with software that was written for v1 PMUs,
i.e. for software that will never manually set the global enables.
- Disable LBR virtualization on CPUs that don't support LBR callstacks, as
KVM unconditionally uses PERF_SAMPLE_BRANCH_CALL_STACK when creating the
virtual LBR perf event, i.e. KVM will always fail to create LBR events on
such CPUs.
- Fix a math goof in x86's hugepage logic for KVM_SET_MEMORY_ATTRIBUTES that
results in an array overflow (detected by KASAN).
- Fix a flaw in the max_guest_memory selftest that results in it exhausting
the supply of ucall structures when run with more than 256 vCPUs.
- Mark KVM_MEM_READONLY as supported for RISC-V in set_memory_region_test.
- Fix a bug where KVM incorrectly thinks a TDP MMU root is an indirect shadow
root due KVM unnecessarily clobbering root_role.direct when userspace sets
guest CPUID.
- Fix a dirty logging bug in the where KVM fails to write-protect TDP MMU
SPTEs used for L2 if Page-Modification Logging is enabled for L1 and the L1
hypervisor is NOT using EPT (if nEPT is enabled, KVM doesn't use the TDP MMU
to run L2). For simplicity, KVM always disables PML when running L2, but
the TDP MMU wasn't accounting for root-specific conditions that force write-
protect based dirty logging.
ZynqMP TCM information was fixed in driver. Now ZynqMP TCM information
is available in device-tree. Parse TCM information in driver
as per new bindings.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20240412183708.4036007-5-tanmay.shah@amd.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Introduce bindings for TCM memory address space on AMD-xilinx Zynq
UltraScale+ platform. It will help in defining TCM in device-tree
and make it's access platform agnostic and data-driven.
Tightly-coupled memories(TCMs) are low-latency memory that provides
predictable instruction execution and predictable data load/store
timing. Each Cortex-R5F processor contains two 64-bit wide 64 KB memory
banks on the ATCM and BTCM ports, for a total of 128 KB of memory.
The TCM resources(reg, reg-names and power-domain) are documented for
each TCM in the R5 node. The reg and reg-names are made as required
properties as we don't want to hardcode TCM addresses for future
platforms and for zu+ legacy implementation will ensure that the
old dts without reg/reg-names works and stable ABI is maintained.
It also extends the examples for TCM split and lockstep modes.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20240412183708.4036007-3-tanmay.shah@amd.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
In lockstep mode, r5 core0 uses TCM of R5 core1. Following is lockstep
mode memory region as per hardware reference manual.
| *TCM* | *R5 View* | *Linux view* |
| R5_0 ATCM (128 KB) | 0x0000_0000 | 0xFFE0_0000 |
| R5_0 BTCM (128 KB) | 0x0002_0000 | 0xFFE2_0000 |
However, driver shouldn't model it as above because R5 core0 TCM and core1
TCM has different power-domains mapped to it.
Hence, TCM address space in lockstep mode should be modeled as 64KB
regions only where each region has its own power-domain as following:
| *TCM* | *R5 View* | *Linux view* |
| R5_0 ATCM0 (64 KB) | 0x0000_0000 | 0xFFE0_0000 |
| R5_0 BTCM0 (64 KB) | 0x0002_0000 | 0xFFE2_0000 |
| R5_0 ATCM1 (64 KB) | 0x0001_0000 | 0xFFE1_0000 |
| R5_0 BTCM1 (64 KB) | 0x0003_0000 | 0xFFE3_0000 |
This makes driver maintanance easy and makes design robust for future
platorms as well.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20240412183708.4036007-2-tanmay.shah@amd.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
This commit contains a series of clean-ups and fixes for bpftool's bash
completion file:
- Make sure all local variables are declared as such.
- Make sure variables are initialised before being read.
- Update ELF section ("maps" -> ".maps") for looking up map names in
object files.
- Fix call to _init_completion.
- Move definition for MAP_TYPE and PROG_TYPE higher up in the scope to
avoid defining them multiple times, reuse MAP_TYPE where relevant.
- Simplify completion for "duration" keyword in "bpftool prog profile".
- Fix completion for "bpftool struct_ops register" and "bpftool link
(pin|detach)" where we would repeatedly suggest file names instead of
suggesting just one name.
- Fix completion for "bpftool iter pin ... map MAP" to account for the
"map" keyword.
- Add missing "detach" suggestion for "bpftool link".
Signed-off-by: Quentin Monnet <qmo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240413011427.14402-3-qmo@kernel.org
When using references to BPF programs, bpftool supports passing programs
by name on the command line. The manual pages for "bpftool prog" and
"bpftool map" (for prog_array updates) mention it, but we have a few
additional subcommands that support referencing programs by name but do
not mention it in their documentation. Let's update the pages for
subcommands "btf", "cgroup", and "net".
Similarly, we can reference maps by name when passing them to "bpftool
prog load", so we update the page for "bpftool prog" as well.
Signed-off-by: Quentin Monnet <qmo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240413011427.14402-2-qmo@kernel.org
This patch addresses a latent unsoundness issue in the
scalar(32)_min_max_and/or/xor functions. While it is not a bugfix,
it ensures that the functions produce sound outputs for all inputs.
The issue occurs in these functions when setting signed bounds. The
following example illustrates the issue for scalar_min_max_and(),
but it applies to the other functions.
In scalar_min_max_and() the following clause is executed when ANDing
positive numbers:
/* ANDing two positives gives a positive, so safe to
* cast result into s64.
*/
dst_reg->smin_value = dst_reg->umin_value;
dst_reg->smax_value = dst_reg->umax_value;
However, if umin_value and umax_value of dst_reg cross the sign boundary
(i.e., if (s64)dst_reg->umin_value > (s64)dst_reg->umax_value), then we
will end up with smin_value > smax_value, which is unsound.
Previous works [1, 2] have discovered and reported this issue. Our tool
Agni [2, 3] consideres it a false positive. This is because, during the
verification of the abstract operator scalar_min_max_and(), Agni restricts
its inputs to those passing through reg_bounds_sync(). This mimics
real-world verifier behavior, as reg_bounds_sync() is invariably executed
at the tail of every abstract operator. Therefore, such behavior is
unlikely in an actual verifier execution.
However, it is still unsound for an abstract operator to set signed bounds
such that smin_value > smax_value. This patch fixes it, making the abstract
operator sound for all (well-formed) inputs.
It is worth noting that while the previous code updated the signed bounds
(using the output unsigned bounds) only when the *input signed* bounds
were positive, the new code updates them whenever the *output unsigned*
bounds do not cross the sign boundary.
An alternative approach to fix this latent unsoundness would be to
unconditionally set the signed bounds to unbounded [S64_MIN, S64_MAX], and
let reg_bounds_sync() refine the signed bounds using the unsigned bounds
and the tnum. We found that our approach produces more precise (tighter)
bounds.
For example, consider these inputs to BPF_AND:
/* dst_reg */
var_off.value: 8608032320201083347
var_off.mask: 615339716653692460
smin_value: 8070450532247928832
smax_value: 8070450532247928832
umin_value: 13206380674380886586
umax_value: 13206380674380886586
s32_min_value: -2110561598
s32_max_value: -133438816
u32_min_value: 4135055354
u32_max_value: 4135055354
/* src_reg */
var_off.value: 8584102546103074815
var_off.mask: 9862641527606476800
smin_value: 2920655011908158522
smax_value: 7495731535348625717
umin_value: 7001104867969363969
umax_value: 8584102543730304042
s32_min_value: -2097116671
s32_max_value: 71704632
u32_min_value: 1047457619
u32_max_value: 4268683090
After going through tnum_and() -> scalar32_min_max_and() ->
scalar_min_max_and() -> reg_bounds_sync(), our patch produces the following
bounds for s32:
s32_min_value: -1263875629
s32_max_value: -159911942
Whereas, setting the signed bounds to unbounded in scalar_min_max_and()
produces:
s32_min_value: -1263875629
s32_max_value: -1
As observed, our patch produces a tighter s32 bound. We also confirmed
using Agni and SMT verification that our patch always produces signed
bounds that are equal to or more precise than setting the signed bounds to
unbounded in scalar_min_max_and().
[1] https://sanjit-bhat.github.io/assets/pdf/ebpf-verifier-range-analysis22.pdf
[2] https://link.springer.com/chapter/10.1007/978-3-031-37709-9_12
[3] https://github.com/bpfverif/agni
Co-developed-by: Matan Shachnai <m.shachnai@rutgers.edu>
Signed-off-by: Matan Shachnai <m.shachnai@rutgers.edu>
Co-developed-by: Srinivas Narayana <srinivas.narayana@rutgers.edu>
Signed-off-by: Srinivas Narayana <srinivas.narayana@rutgers.edu>
Co-developed-by: Santosh Nagarakatte <santosh.nagarakatte@rutgers.edu>
Signed-off-by: Santosh Nagarakatte <santosh.nagarakatte@rutgers.edu>
Signed-off-by: Harishankar Vishwanathan <harishankar.vishwanathan@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240402212039.51815-1-harishankar.vishwanathan@gmail.com
Link: https://lore.kernel.org/bpf/20240416115303.331688-1-harishankar.vishwanathan@gmail.com
Once there is a heavy IO load, so many encrypt/decrypt work will occupy
all of the cpu, which may lead to the poor performance for other service.
So the improved visibility and controls over dm-crypt workqueues, as
was offered with commit a2b8b2d975 ("dm crypt: export sysfs of
kcryptd workqueue"), seems necessary. By exporting dm-crypt's
workqueues in sysfs, the entry like cpumask/max_active and so on can
help us to limit the CPU usage for encrypt/decrypt work.
However, commit a2b8b2d975 did not consider that DM table reload
will call .ctr before .dtr, so the reload for dm-crypt failed because
the same sysfs name was present. This was the original need for commit
48b0777cd9 ("Revert "dm crypt: export sysfs of kcryptd workqueue"").
Reintroduce the use of WQ_SYSFS, and use it for both the IO and crypt
workqueues, but make the workqueue names include a unique id (via ida)
to allow both old and new sysfs entries to coexist.
Signed-off-by: yangerkun <yangerkun@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
When WQ_HIGHPRI was used for the dm-crypt kcryptd workqueue it was
reported that dm-crypt performs badly when the system is loaded[1].
Because of reports of audio skipping, dm-crypt stopped using
WQ_HIGHPRI with commit f612b2132d (Revert "dm crypt: use WQ_HIGHPRI
for the IO and crypt workqueues").
But it has since been determined that WQ_HIGHPRI provides improved
performance (with reduced latency) for highend systems with much more
resources than those laptop/desktop users which suffered from the use
of WQ_HIGHPRI.
As such, add an option "high_priority" that allows the use of
WQ_HIGHPRI for dm-crypt's workqueues and also sets the write_thread to
nice level MIN_NICE (-20). This commit makes it optional, so that
normal users won't be harmed by it.
[1] https://listman.redhat.com/archives/dm-devel/2023-February/053410.html
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
'dmsetup remove' and 'dmsetup remove_all' require synchronous bdev
release. Otherwise dm_lock_for_deletion() may return -EBUSY if the open
count is > 0, because the open count is dropped in dm_blk_close()
which occurs after fput() completes.
So if dm_blk_close() is delayed because of asynchronous fput(), this
device mapper device is skipped during remove, which is a regression.
Fix the issue by using __fput_sync().
Also, DM device removal has long supported being made asynchronous by
setting the DMF_DEFERRED_REMOVE flag on the DM device. So leverage
using async fput() in close_table_device() if DMF_DEFERRED_REMOVE flag
is set.
Reported-by: Zhong Changhui <czhong@redhat.com>
Fixes: a28d893eb3 ("md: port block device access to file")
Suggested-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[snitzer: editted commit header, use fput() if DMF_DEFERRED_REMOVE set]
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Document support for the Compare Match Timer Type0 (CMT0) and Type1
(CMT1) in the Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/3e8a7a93261d8ad264dec2fa2784fe1bbfc4a23c.1712068536.git.geert+renesas@glider.be
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
wilc1000 driver currently uses SRCU API to manage vif list. There is no
real reason to use SRCU API here, and it makes things slightly more
complicated (we need to handle a SRCU index as well as a srcu_struct) than
classical RCU.
Switch SRCU APIs to RCU APIs.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240410-wilc_srcu_to_rcu-v1-2-a9ff5b10feaa@bootlin.com
In order to prepare wilc1000 driver switch from SRCU to RCU, make sure that
allocators are provided with the GFP_ATOMIC flag when called in a critical
read section.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240410-wilc_srcu_to_rcu-v1-1-a9ff5b10feaa@bootlin.com
Commit c3718936ec ("ipv6: anycast: complete RCU handling of struct
ifacaddr6") converted struct inet6_dev::ac_list to use RCU but missed that
ath11k also accesses this list. Now sparse warns:
drivers/net/wireless/ath/ath11k/mac.c:9145:21: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:21: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:21: got struct ifacaddr6 [noderef] __rcu *ac_list
drivers/net/wireless/ath/ath11k/mac.c:9145:53: warning: incorrect type in assignment (different address spaces)
drivers/net/wireless/ath/ath11k/mac.c:9145:53: expected struct ifacaddr6 *ifaca6
drivers/net/wireless/ath/ath11k/mac.c:9145:53: got struct ifacaddr6 [noderef] __rcu *aca_next
Fix it by using rtnl_dereference(). Also add a note that read_lock_bh() calls
rcu_read_lock() which I was not aware of.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.37
Fixes: c3718936ec ("ipv6: anycast: complete RCU handling of struct ifacaddr6")
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240411165516.4070649-2-kvalo@kernel.org
Currently, there are two comments with same name "64-bit ATOMIC magnitudes",
the second one should be "32-bit ATOMIC magnitudes" based on the context.
Signed-off-by: Chen Pei <cp0613@linux.alibaba.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240415081928.17440-1-cp0613@linux.alibaba.com
When __bpf_prog_enter() returns zero, the s1 register is not set to zero,
resulting in incorrect runtime stats. Fix it by setting s1 immediately upon
the return of __bpf_prog_enter().
Fixes: 49b5e77ae3 ("riscv, bpf: Add bpf trampoline support for RV64")
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Pu Lehui <pulehui@huawei.com>
Acked-by: Björn Töpel <bjorn@kernel.org>
Link: https://lore.kernel.org/bpf/20240416064208.2919073-3-xukuohai@huaweicloud.com
When __bpf_prog_enter() returns zero, the arm64 register x20 that stores
prog start time is not assigned to zero, causing incorrect runtime stats.
To fix it, assign the return value of bpf_prog_enter() to x20 register
immediately upon its return.
Fixes: efc9909fdc ("bpf, arm64: Add bpf trampoline for arm64")
Reported-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Ivan Babrou <ivan@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20240416064208.2919073-2-xukuohai@huaweicloud.com
The parameter name is 'sb' and not 'drm_scanout_buffer'.
It fixes the following warnings:
drivers/gpu/drm/drm_fb_dma_helper.c:166: warning: Excess function parameter 'drm_scanout_buffer' description in 'drm_fb_dma_get_scanout_buffer'
drivers/gpu/drm/drm_fb_dma_helper.c:166: warning: Function parameter or struct member 'sb' not described in 'drm_fb_dma_get_scanout_buffer'
drivers/gpu/drm/drm_fb_dma_helper.c:166: warning: Excess function parameter 'drm_scanout_buffer' description in 'drm_fb_dma_get_scanout_buffer'
Fixes: 879b3b6511 ("drm/fb_dma: Add generic get_scanout_buffer() for drm_panic")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416090601.237286-1-jfalempe@redhat.com
If the BTF code is enabled in the build configuration, the start/stop
BTF markers are guaranteed to exist. Only when CONFIG_DEBUG_INFO_BTF=n,
the references in btf_parse_vmlinux() will remain unsatisfied, relying
on the weak linkage of the external references to avoid breaking the
build.
Avoid GOT based relocations to these markers in the final executable by
dropping the weak attribute and instead, make btf_parse_vmlinux() return
ERR_PTR(-ENOENT) directly if CONFIG_DEBUG_INFO_BTF is not enabled to
begin with. The compiler will drop any subsequent references to
__start_BTF and __stop_BTF in that case, allowing the link to succeed.
Note that Clang will notice that taking the address of __start_BTF can
no longer yield NULL, so testing for that condition becomes unnecessary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20240415162041.2491523-8-ardb+git@google.com
In some cases, the stack pointer on x86 (rsp = reg7) is used to point
variables on stack but it's not the frame base register. Then it
should handle the register like normal registers (IOW not to access
the other stack variables using offset calculation) but it should not
assume it would have a pointer.
Before:
-----------------------------------------------------------
find data type for 0x7c(reg7) at tcp_getsockopt+0xb62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
no pointer or no type
check variable "zc" failed (die: 0x7b9580a)
variable location: base=reg7, offset=0x40
type='struct tcp_zerocopy_receive' size=0x40 (die:0x7b947f4)
After:
-----------------------------------------------------------
find data type for 0x7c(reg7) at tcp_getsockopt+0xb62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
found "zc" in scope=3/3 (die: 0x7b957fc) type_offset=0x3c
variable location: base=reg7, offset=0x40
type='struct tcp_zerocopy_receive' size=0x40 (die:0x7b947f4)
Note that the type-offset was properly calculated to 0x3c as the
variable starts at 0x40.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240412183310.2518474-5-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In match_var_offset(), it just checked the end address of the variable
with the given offset because it assumed the register holds a pointer
to the data type and the offset starts from the base.
But I found some cases that the stack pointer (rsp = reg7) register is
used to pointer a stack variable while the frame base is maintained by a
different register (rbp = reg6). In that case, it cannot simply use the
stack pointer as it cannot guarantee that it points to the frame base.
So it needs to check both boundaries of the variable location.
Before:
-----------------------------------------------------------
find data type for 0x7c(reg7) at tcp_getsockopt+0xb62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
no pointer or no type
check variable "tss" failed (die: 0x7b95801)
variable location: base reg7, offset=0x110
type='struct scm_timestamping_internal' size=0x30 (die:0x7b8c126)
So the current code just checks register number for the non-PC and
non-FB registers and assuming it has offset 0. But this variable has
offset 0x110 so it should not match to this.
After:
-----------------------------------------------------------
find data type for 0x7c(reg7) at tcp_getsockopt+0xb62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
no pointer or no type
check variable "zc" failed (die: 0x7b9580a)
variable location: base=reg7, offset=0x40
type='struct tcp_zerocopy_receive' size=0x40 (die:7b947f4)
Now it find the correct variable "zc". It was located at reg7 + 0x40
and the size if 0x40 which means it should cover [0x40, 0x80). And the
access was for reg7 + 0x7c so it found the right one. But it still
failed to use the variable and it would be handled in the next patch.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240412183310.2518474-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In match_var_offset(), it checks the offset range with the target type
only for non-pointer types. But it also needs to check the pointer
types with the target type.
This is because there can be more than one pointer variable located in
the same register. Let's look at the following example. It's looking
up a variable for reg3 at tcp_get_info+0x62. It found "sk" variable but
it wasn't the right one since it accesses beyond the target type (struct
'sock' in this case) size.
-----------------------------------------------------------
find data type for 0x7bc(reg3) at tcp_get_info+0x62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
offset: 1980 is bigger than size: 760
check variable "sk" failed (die: 0x7b92b2c)
variable location: reg3
type='struct sock' size=0x2f8 (die:0x7b63c3a)
Actually there was another variable "tp" in the function and it's
located at the same (reg3) because it's just type-casted like below.
void tcp_get_info(struct sock *sk, struct tcp_info *info)
{
const struct tcp_sock *tp = tcp_sk(sk);
...
The 'struct tcp_sock' contains the 'struct sock' at offset 0 so it can
just use the same address as a pointer to tcp_sock. That means it
should match variables correctly by checking the offset and size.
Actually it cannot distinguish if the offset was smaller than the size
of the original struct sock. But I think it's fine as they are the same
at that part.
So let's check the target type size and retry if it doesn't match.
Now it succeeded to find the correct variable.
-----------------------------------------------------------
find data type for 0x7bc(reg3) at tcp_get_info+0x62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
found "tp" in scope=1/1 (die: 0x7b92b16) type_offset=0x7bc
variable location: reg3
type='struct tcp_sock' size=0xa68 (die:0x7b81380)
Fixes: bc10db8eb8 ("perf annotate-data: Support stack variables")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240412183310.2518474-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To verify it found the correct variable, let's add the location
expression to the debug message.
$ perf --debug type-profile annotate --data-type
...
-----------------------------------------------------------
find data type for 0xaf0(reg15) at schedule+0xeb
CU for kernel/sched/core.c (die:0x1180523)
frame base: cfa=0 fbreg=6
found "rq" in scope=3/4 (die: 0x11b6a00) type_offset=0xaf0
variable location: reg15
type='struct rq' size=0xfc0 (die:0x11892e2)
-----------------------------------------------------------
find data type for 0x7bc(reg3) at tcp_get_info+0x62
CU for net/ipv4/tcp.c (die:0x7b5f516)
frame base: cfa=0 fbreg=6
offset: 1980 is bigger than size: 760
check variable "sk" failed (die: 0x7b92b2c)
variable location: reg3
type='struct sock' size=0x2f8 (die:0x7b63c3a)
-----------------------------------------------------------
...
The first case is fine. It looked up a data type in r15 with offset of
0xaf0 at schedule+0xeb. It found the CU die and the frame base info and
the variable "rq" was found in the scope 3/4. Its location is the r15
register and the type size is 0xfc0 which includes 0xaf0.
But the second case is not good. It looked up a data type in rbx (reg3)
with offset 0x7bc. It found a CU and the frame base which is good so
far. And it also found a variable "sk" but the access offset is bigger
than the type size (1980 vs. 760 or 0x7bc vs. 0x2f8). The variable has
the right location (reg3) but I need to figure out why it accesses
beyond what it's supposed to.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240412183310.2518474-2-namhyung@kernel.org
[ Fix the build on 32-bit by casting Dwarf_Word to (long) in pr_debug_location() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Previously, the audio status was not updated during detection, leading
to a persistent audio despite hot plugging events. To resolve this
issue, update the audio status during detection.
Fixes: 566fef1226 ("drm/bridge: anx7625: add HDMI audio function")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416-anx7625-v3-1-f916ae31bdd7@chromium.org
If we fail to allocate propname buffer, we need to drop the reference
count we just took. Because the pinctrl_dt_free_maps() includes the
droping operation, here we call it directly.
Fixes: 91d5c5060e ("pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map")
Suggested-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Message-ID: <20240415105328.3651441-1-zengheng4@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Serge Semin says:
====================
net: stmmac: Fix MAC-capabilities procedure
The series got born as a result of the discussions around the recent
Yanteng' series adding the Loongson LS7A1000, LS2K1000, LS7A2000, LS2K2000
MACs support:
Link: https://lore.kernel.org/netdev/fu3f6uoakylnb6eijllakeu5i4okcyqq7sfafhp5efaocbsrwe@w74xe7gb6x7p
In particular the Yanteng' patchset needed to implement the Loongson
MAC-specific constraints applied to the link speed and link duplex mode.
As a result of the discussion with Russel the next preliminary patch was
born:
Link: https://lore.kernel.org/netdev/df31e8bcf74b3b4ddb7ddf5a1c371390f16a2ad5.1712917541.git.siyanteng@loongson.cn
The patch above was a temporal solution utilized by Yanteng for further
developments and to move on with the on-going review. This patchset is a
refactored version of that single patch with formatting required for the
fixes patches.
In particular the series starts with fixing the half-duplex-less
constraint currently applied for all IP-cores. In fact it's specific for
the DW QoS Eth only (DW GMAC v4.x/v5.x).
The next patch fixes the MAC-capabilities setting up during the active
Tx/Rx queues re-initialization procedure. Particularly the procedure
missed the max-speed limit thus possibly activating speeds prohibited on
the respective platforms.
Third patch fixes the incorrect MAC-capabilities initialization for DW
MAC100, DW XGMAC and DW XLGMAC devices by moving the correct
initialization to the IP-core specific setup() methods.
That's it for now. Thanks for review and testing in advance.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Simon Horman <horms@kernel.org>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Cc: netdev@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@lists.linux.dev
Cc: linux-kernel@vger.kernel.org
====================
Link: https://lore.kernel.org/r/20240412180340.7965-1-fancer.lancer@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e9 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da6 ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e9 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f3 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-9-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 623a3531e9 ("drm/panel: Add driver for Novatek NT35950 DSI DriverIC panels")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-8-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Also move the "failed to attach" error message so that it's only printed
when the devm_mipi_dsi_attach() call fails.
Fixes: 6352cd451d ("drm: bridge: Add TI DLPC3433 DSI to DMD bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-7-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: b26975593b ("display/drm/bridge: TC358775 DSI/LVDS driver")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-6-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 0cbbd5b1a0 ("drm: bridge: add support for lontium LT9611UXC bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-5-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 23278bf54a ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-4-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 30e2ae943c ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-3-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 8dde6f7452 ("drm: bridge: icn6211: Add I2C configuration support")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-2-619a28148e5c@collabora.com
Given that failing to find a DSI host causes the driver to defer probe,
make use of dev_err_probe() to log the reason. This makes the defer
probe reason available and avoids alerting userspace about something
that is not necessarily an error.
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240415-anx7625-defer-log-no-dsi-host-v3-1-619a28148e5c@collabora.com
No new changes will be added for minor version 2. Change the minor
version number to 2 and stop displaying log message for unsupported
minor version 2.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240415220625.2828339-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Add Granite Rapids-D to hpm_cpu_ids, so that MSR 0x54 can be used.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240415212853.2820470-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
ROG Zephyrus G14 advertises support for SPS notifications to the
BIOS but doesn't actually use them. Instead the asus-nb-wmi driver
utilizes such events.
Add a quirk to prevent the system from registering for ACPI platform
profile when this system is found to avoid conflicts.
Reported-by: al0uette@outlook.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218685
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240410140956.385-3-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
In the event of a BIOS bug add infrastructure that will be utilized
to override the return value for supported_funcs to avoid enabling
features.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240410140956.385-2-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
ASUS ROG Zephyrus G14 doesn't have _CRS in AMDI0102 device and so
there are no resources to walk. This is expected behavior because
it doesn't support Smart PC. Decrease error message to debug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218685
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240410140956.385-1-mario.limonciello@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Too much print may lead to a panic in kernel. Change ibdev_err() to
ibdev_err_ratelimited(), and change the printing level of cqe dump
to debug level.
Fixes: 7c044adca2 ("RDMA/hns: Simplify the cqe code of poll cq")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240412091616.370789-11-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Use complete parentheses to ensure that macro expansion does
not produce unexpected results.
Fixes: a25d13cbe8 ("RDMA/hns: Add the interfaces to support multi hop addressing for the contexts in hip08")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240412091616.370789-10-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
GMV's BA table only supports 4K pages. Currently, PAGESIZE is used to
calculate gmv_bt_num, which will cause an abnormal number of gmv_bt_num
in a 64K OS.
Fixes: d6d91e4621 ("RDMA/hns: Add support for configuring GMV table")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://lore.kernel.org/r/20240412091616.370789-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
