max range of the agp aperture is 48 bits, so
enlarge agp_start address into 48bit with all bits set
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
currently using TMR loading VCN fw MMSCH would fail
to init after FLR, just disable ib test for temporarily
daily testing, continuing debug with mm team.
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This workaround does not affect other asics because amdgpu only need expose
one gfx sched to user for now.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DF routines to arm xGMI performance will attempt to re-arm both on
performance monitoring start and read on initial failure to arm.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During DF C-State, Perfmon counters outside of range 1D700-1D7FF will
encounter SLVERR affecting xGMI performance monitoring. PerfmonCtr[7:4]
is being added to avoid SLVERR during read since it falls within this
range. PerfmonCtl[7:4] is being added in order to arm PerfmonCtr[7:4].
Since PerfmonCtl[7:4] exists outside of range 1D700-1D7FF, DF routines
will be enabled to opportunistically re-arm PerfmonCtl[7:4] on retry
after SLVERR.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Acked-by: Alex Deucher <Alexander.Deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simplify padding calculations.
v2: Comment update and spacing.
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rseq.h UAPI now documents that the rseq_cs field must be cleared
before reclaiming memory that contains the targeted struct rseq_cs, but
also that the rseq_cs field must be cleared before reclaiming memory of
the code pointed to by the rseq_cs start_ip and post_commit_offset
fields.
While we can expect that use of dlclose(3) will typically unmap
both struct rseq_cs and its associated code at once, nothing would
theoretically prevent a JIT from reclaiming the code without
reclaiming the struct rseq_cs, which would erroneously allow the
kernel to consider new code which is not a rseq critical section
as a rseq critical section following a code reclaim.
Suggested-by: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Florian Weimer <fw@deneb.enyo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
glibc 2.30 introduces gettid() in public headers, which clashes with
the internal static definition within rseq selftests.
Rename gettid() to rseq_gettid() to eliminate this symbol name clash.
Reported-by: Tommi T. Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Tommi T. Rantala <tommi.t.rantala@nokia.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
As the rseq selftests can run for a long period of time, disable the
timeout that the general selftests have.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Paul Turner <pjt@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This commit renames 'kunitconfig' to '.kunitconfig' so that it can be
automatically ignored by git and do not disturb people who want to type
'kernel/' by pressing only the 'k' and then 'tab' key.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'kunit' writes the 'test.log' under the kernel source directory even
though a 'build_dir' option is given. As users who use the option might
expect the outputs to be placed under the specified directory, this
commit modifies the logic to write the log file under the 'build_dir'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
If both '--build_dir' and '--defconfig' are given, the handling of
'--defconfig' ignores '--build_dir' option. This commit modifies the
behavior to respect '--build_dir' option.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Suggested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
'--defconfig' option is handled by the 'main() of the 'kunit.py' but
again handled in following 'run_tests()'. This commit removes this
duplicated handling of the option in the 'run_tests()'.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The kunit doc suggests users to get the default `kunitconfig` from an
external git tree. However, the file is already located under the
`arch/um/configs/` of the kernel tree. Because the local file is easier
to access and maintain, this commit updates the doc to use it.
Signed-off-by: SeongJae Park <sjpark@amazon.de>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
livepatch test configures the system and debug environment to run
tests. Some of these actions fail without root access and test
dumps several permission denied messages before it exits.
Fix test-state.sh to call setup_config instead of set_dynamic_debug
as suggested by Petr Mladek <pmladek@suse.com>
Fix it to check root uid and exit with skip code instead.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Joe Lawrence <joe.lawrence@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
firmware attempts to load test modules that require root access
and fail. Fix it to check for root uid and exit with skip code
instead.
Before this fix:
selftests: firmware: fw_run_tests.sh
modprobe: ERROR: could not insert 'test_firmware': Operation not permitted
You must have the following enabled in your kernel:
CONFIG_TEST_FIRMWARE=y
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_USER_HELPER=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
With this fix:
selftests: firmware: fw_run_tests.sh
skip all tests: must be run as root
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Reviwed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
epoll build fails to find pthread lib. Fix Makefile to use LDLIBS
instead of LDFLAGS. LDLIBS is the right flag to use here with -l
option when invoking ld.
gcc -I../../../../../usr/include/ -lpthread epoll_wakeup_test.c -o .../tools/testing/selftests/filesystems/epoll/epoll_wakeup_test
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `kill_timeout':
epoll_wakeup_test.c:(.text+0x4dd): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x4f2): undefined reference to `pthread_kill'
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `epoll9':
epoll_wakeup_test.c:(.text+0x6382): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x64d2): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6626): undefined reference to `pthread_join'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x684c): undefined reference to `pthread_tryjoin_np'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6864): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6878): undefined reference to `pthread_join'
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This function is only called from port sync and it is identical to
what will be executed again in intel_update_crtc() over port sync
pipes.
If it is really necessary at least it deserves a better name and a
comment, leaving it to people working on port sync.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-7-jose.souza@intel.com
MST master can not be disabled while it have attached MST slaves, so
it is necessary force a modeset in all of its slaves.
v3:
- moved handling to intel_atomic_check() this way is guarantee that
all pipes will have its state computed
v4:
- added a function to return if MST master neeeds modeset to simply
code in intel_atomic_check()
v5:
- fixed and moved code to check if MST master needs a modeset
v6:
- previons version of this patch was split into two patches
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-6-jose.souza@intel.com
MST and port sync have master and slaves pipes and it brings
dependencies between pipes to allow fastset.
For example if only MST master needs a modeset all of its slaves also
needs to do a modeset.
This patch adds the base for external dependencies check, the MST and
port sync bits will be added in another patches.
v3:
- moved handling to intel_atomic_check() this way is guarantee that
all pipes will have its state computed
v4:
- added a function to return if MST master neeeds modeset to simply
code in intel_atomic_check()
v5:
- fixed and moved code to check if MST master needs a modeset
v6:
- previons version of this patch was split into two patches
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-5-jose.souza@intel.com
The disable sequence after wait for transcoder off was not correctly
implemented.
The MST disable sequence is basically the same for HSW, SKL, ICL and
TGL, with just minor changes for TGL.
With this last patch we finally fixed the hotplugs triggered by MST
sinks during the disable/enable sequence, those were causing source
to try to do a link training while it was not ready causing CPU pipe
FIFO underrrus on TGL.
v2: Only unsetting TGL_TRANS_DDI_PORT_MASK for TGL on the post
disable sequence
v4: Rebased, moved MST sequences to intel_mst_post_disable_dp()
BSpec: 4231
BSpec: 4163
BSpec: 22243
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-4-jose.souza@intel.com
Due to DDB overlaps the pipe enabling sequence is not always crescent.
As the previous patch selects the smallest pipe/transcoder in the MST
stream to be master and it needs to be enabled first, this changes
were needed to guarantee that.
So first lets enable all pipes that do not need a fullmodeset as
those don't have any external dependency and those are the ones that
can overlap with each other.
Then on the second loop it will enable all the pipes that needs a
modeset and don't depends on other pipes like MST master
pipe/transcoder.
Then finally all the pipes that needs a modeset and have dependency
on other pipes, that at this point are alread enabled.
v3: rebased
v4:
- added check for modeset_pipes too to decide if is necessary for a
wait a vblank
- added DDB allocation overlap check for pipes that needs a modeset
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-3-jose.souza@intel.com
On TGL the blending of all the streams have moved from DDI to
transcoder, so now every transcoder working over the same MST port must
send its stream to a master transcoder and master will send to DDI
respecting the time slots.
So here adding all the CRTCs that shares the same MST stream if
needed and computing their state again, it will pick the lowest
pipe/transcoder among the ones in the same stream to be master.
Most of the time skl_commit_modeset_enables() enables pipes in a
crescent order but due DDB overlapping it might not happen, this
scenarios will be handled in the next patch.
v2:
- Using recently added intel_crtc_state_reset() to set
mst_master_transcoder to invalid transcoder for all non gen12 & MST
code paths
- Setting lowest pipe/transcoder as master, previously it was the
first one but setting a predictable one will help in future MST e
port sync integration
- Moving to intel type as much as we can
v3:
- Now intel_dp_mst_master_trans_compute() returns the MST master transcoder
- Replaced stdbool.h by linux/types.h
- Skip the connector being checked in
intel_dp_mst_atomic_master_trans_check()
- Using pipe instead of transcoder to compute MST master
v4:
- renamed connector_state to conn_state
v5:
- Improved the parameters of intel_dp_mst_master_trans_compute() to
simply code
- Added call drm_atomic_add_affected_planes() in
intel_dp_mst_atomic_master_trans_check() as helper could not do it
for us
- Removed "if (ret)" left over from v3 changes
v6:
- handled ret == I915_MAX_PIPES case in compute
BSpec: 50493
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-2-jose.souza@intel.com
intel_connector_needs_modeset() will be used outside of
intel_display.c in a future patch so it would only be necessary to
remove the state and add the prototype to the header file.
But while at it, I simplified the arguments and moved it to a better
place intel_atomic.c.
No behavior changes intended here.
v3:
- removed digital from exported version of intel_connector_needs_modeset
- rollback connector to drm type
v4:
- Renamed new_connector_state to new_conn_state
- Going back to drm_connector_state in
intel_encoders_update_prepare/complete as we also have
intel_tv_connector_state
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191223010654.67037-1-jose.souza@intel.com
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f85 ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In error cases a NULL can be passed to memcpy. The length will always
be zero, so it doesn't really matter, but go ahead and check for NULL,
anyway, to be more precise and avoid static analysis errors.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Commit e61df66c69 ("io-wq: ensure free/busy list browsing see all
items") added a list for io workers in addition to the free and busy
lists, not only making worker walk cleaner, but leaving the busy list
unused. Let's remove it.
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When listing a directory with thounsands of files and most of them are
reparse points, we simply marked all those dentries for revalidation
and then sending additional (compounded) create/getinfo/close requests
for each of them.
Instead, upon receiving a response from an SMB2_QUERY_DIRECTORY
(FileIdFullDirectoryInformation) command, the directory entries that
have a file attribute of FILE_ATTRIBUTE_REPARSE_POINT will contain an
EaSize field with a reparse tag in it, so we parse it and mark the
dentry for revalidation only if it is a DFS or a symlink.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Clang warns:
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 592fafe644 ("Add resilienthandles mount parm")
Link: https://github.com/ClangBuiltLinux/linux/issues/826
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
In a development period for v5.6 kernel, some changes are introduced to
structures in ALSA control interface:
- 'tstamp' member is removed from 'struct snd_ctl_elem_value
- 'TSTAMP' flag is removed from a set of access flags for 'struct
snd_ctl_elem_info'
- 'dimen' member is removed from 'struct snd_ctl_elem_info
Although these changes were introduced with enough consideration for
backward compatibility, they include slightly lose of it. This commit
bumps protocol version of ALSA control interface up to v2.1.0.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191223023921.8151-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 'dimen' member of 'struct snd_ctl_elem_info' is designed to deliver
information to use an array of value as multi-dimensional values. This
feature is used just by echoaudio PCI driver, and fortunately it's not
used by the other applications than 'echomixer' in alsa-tools.
In a previous commit, usage of 'dimen' member is removed from echoaudio
PCI driver. Nowadays no driver/application use the feature.
This commit removes the member from structure.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191223023921.8151-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a couple of years ago, 'echomixer' userspace application was revised
not to use 'dimen' member of 'struct snd_ctl_elem_info'.
This commit removes usage of 'dimen' member from echoaudio PCI driver so
that no implementation uses the member.
Reference: 275353bb68 ("ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members")
Reference: 51db452df0 ("Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191223023921.8151-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a former commit, 'tstamp' member was removed from 'struct
snd_ctl_elem_value' in a middle way toward solution of Y2038 issue. In a
protocol of ALSA control interface, this member is designed to deliver
timestamp information in the value structure when the target element
supports SNDRV_CTL_ELEM_ACCESS_TIMESTAMP flag.
Actually, the feature is neither used by kernel space nor user space,
especiall alsa-lib has no API for the feature. Therefore it's reasonable
to remove both of them. Practically, the timestamp information
corresponds to no information about type of clock ID. It can bring
confusions to applications.
Reference: a4e7dd35b9 ("ALSA: Avoid using timespec for struct snd_ctl_elem_value")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191223023921.8151-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I got the following error when I tried to build perf on a read-only
filesystem with O=dir option.
$ cd /some/where/ro/linux/tools/perf
$ make O=$HOME/build/perf
...
CC /home/namhyung/build/perf/lib.o
/bin/sh: bpf_helper_defs.h: Read-only file system
make[3]: *** [Makefile:184: bpf_helper_defs.h] Error 1
make[2]: *** [Makefile.perf:778: /home/namhyung/build/perf/libbpf.a] Error 2
make[2]: *** Waiting for unfinished jobs....
LD /home/namhyung/build/perf/libperf-in.o
AR /home/namhyung/build/perf/libperf.a
PERF_VERSION = 5.4.0
make[1]: *** [Makefile.perf:225: sub-make] Error 2
make: *** [Makefile:70: all] Error 2
It was becaused bpf_helper_defs.h was generated in current directory.
Move it to OUTPUT directory.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191223061326.843366-1-namhyung@kernel.org
The iommu variable in set_device_exclusion_range() us unused
now and causes a compiler warning. Remove it.
Fixes: 387caf0b75 ("iommu/amd: Treat per-device exclusion ranges as r/w unity-mapped regions")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The only protection for intel_context.gem_cotext is granted by RCU, so
annotate it as a rcu protected pointer and carefully dereference it in
the few occasions we need to use it.
Fixes: 9f3ccd40ac ("drm/i915: Drop GEM context as a direct link from i915_request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191222233558.2201901-1-chris@chris-wilson.co.uk
Use the new standard function instead of open-coding it.
Cc: Jean-Philippe Brucker <jean-philippe@linaro.org>
Cc: virtualization@lists.linux-foundation.org
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
