commit 0b21503dbb upstream.
Currently, a RCG's M/N counter (used for fraction division) is
set to either 'bypass' (counter disabled) or 'dual edge' (counter
enabled) based on whether the corresponding rcg struct has a mnd
field specified and a non-zero N.
In the case where M and N are the same value, the M/N counter is
still enabled by code even though no division takes place.
Leaving the RCG in such a state can result in improper behavior.
This was observed with the DSI pixel clock RCG when M and N were
both set to 1.
Add an additional check (M != N) to enable the M/N counter only
when it's needed for fraction division.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock
generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 69daf75aaf upstream.
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[ luis: 3.16 prereq for:
4591243102 "clk: at91: usb: propagate rate modification to the parent clk" ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5e43e25917 upstream.
The number of resets controls is 32 times the number of peripheral
register banks rather than 32 times the number of clocks. This reduces
(drastically) the number of reset controls registered from 10080 (315
clocks * 32) to 224 (6 peripheral register banks * 32).
This also fixes a potential crash because trying to use any of the
excess reset controls (224-10079) would have caused accesses beyond
the array bounds of the peripheral register banks definition array.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Fixes: 6d5b988e7d ("clk: tegra: implement a reset driver")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 26bac95aa8 upstream.
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit da321133b5 upstream.
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbe (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbe (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 76820fcf7a upstream.
For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9a5e6c7eb5 upstream.
The PLLs on newer Allwinner SoC's, such as the A31 and A23, have a
N multiplier factor that starts from 1, not 0.
This patch adds an option to the factor clk driver's config data
structures to specify the base value of N.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 2e9dcdae40 upstream.
In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3dccfecdb8 upstream.
The CPU_2X clock does not have a classical in-kernel user, but is,
amongst other things, required for OCM and debug access. Make sure this
clock is not mistakenly disabled during boot up by enabling it in the
platform's clock driver.
Fixes: 0ee52b157b 'clk: zynq: Add clock controller driver'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 10cdfe54da upstream.
As __clk_release could call kfree on clk and then we wouldn't have a safe way
of getting the module that owns the clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Fixes: fcb0ee6a3d ("clk: Implement clk_unregister")
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit b71e8ecd57 upstream.
The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable
register is for nfc. Current code use bit19 for non-exist "smemc"
incorrectly, this prevents eMMC from working due to the sdhci's
"core" clk is still gated.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit dca1a4b5ff upstream.
All slow clk users are not properly claiming it (get + prepare + enable)
before using it.
If all users properly claiming this clock release it, the clock is
disabled, but faulty users still depends on it, and the system hangs.
This fix prevents the slow clock from being disabled, and should solve the
hanging issue, but offending drivers should be patched to properly claim
this clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e6d5e7d90b upstream.
Commit 79c6ab5095 (clk: divider: add CLK_DIVIDER_READ_ONLY flag) in
v3.16 introduced the CLK_DIVIDER_READ_ONLY flag which caused the
recalc_rate() and round_rate() clock callbacks to be omitted.
However using this flag has the unfortunate side effect of causing the
clock recalculation code when a clock rate change is attempted to always
treat it as a pass-through clock, i.e. with a fixed divide of 1, which
may not be the case. Child clock rates are then recalculated using the
wrong parent rate.
Therefore instead of dropping the recalc_rate() and round_rate()
callbacks, alter clk_divider_bestdiv() to always report the current
divider as the best divider so that it is never altered.
For me the read only clock was the system clock, which divided the PLL
rate by 2, from which both the UART and the SPI clocks were divided.
Initial setting of the UART rate set it correctly, but when the SPI
clock was set, the other child clocks were miscalculated. The UART clock
was recalculated using the PLL rate as the parent rate, resulting in a
UART new_rate of double what it should be, and a UART which spewed forth
garbage when the rate changes were propagated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Max Schwarz <max.schwarz@online.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[ luis: backported to 3.16:
- drop changes to drivers/clk/rockchip/clk.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5b6b7490af upstream.
Sometimes we need to program PLLs with a fixed rate
configuration during driver probe. Doing this after we register
the PLLs with the clock framework causes the common clock
framework to assume the rate of the PLLs are 0. This causes all
sorts of problems for rate recalculations because the common
clock framework caches the rate once at registration time unless
a flag is set to always recalculate the rates.
Split the qcom_cc_probe() function into two pieces, map and
everything else, so that drivers which need to configure some
PLL rates or otherwise twiddle bits in the clock controller can
do so before registering clocks. This allows us to properly
detect the rates of PLLs that are programmed at boot.
Fixes: 49fc825f0c "clk: qcom: Consolidate common probe code"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f87dfcabc6 upstream.
The mdp_lut_clk isn't a child of the mdp_clk. Instead it's the
child of the mdp_src clock. Fix it.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff20783f7b upstream.
Clocks that don't have a pre-divider don't list any pre-divider
in their frequency tables, but their tables are initialized using
aggregate initializers. Use tagged initializers so we properly
assign the m and n values for each frequency. Furthermore, the
mmcc_pxo_pll8_pll2_pll3 array improperly mapped the second
element to pll2 instead of pll8, causing the clock driver to
recalculate the wrong rate for any clocks using this array along
with a rate that uses pll2. Plus the .num_parents field is 3
instead of 4 so you can't even switch the parent to pll3. Finally
I noticed that the jpegd clock improperly indicates that the
pre-divider width is only 2, when it's actually 4 bits wide.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f10325176 upstream.
Check for valid parameters in check rate. Else, we end up getting errors
like:
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0-rc1 #1
[ 0.000000] [<c0015160>] (unwind_backtrace) from [<c0011978>] (show_stack+0x10/0x14)
[ 0.000000] [<c0011978>] (show_stack) from [<c055f5f4>] (dump_stack+0x78/0x94)
[ 0.000000] [<c055f5f4>] (dump_stack) from [<c02e17cc>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02e17cc>] (Ldiv0) from [<c047d228>] (ti_clk_divider_set_rate+0x14/0x14c)
[ 0.000000] [<c047d228>] (ti_clk_divider_set_rate) from [<c047a938>] (clk_change_rate+0x138/0x180)
[ 0.000000] [<c047a938>] (clk_change_rate) from [<c047a908>] (clk_change_rate+0x108/0x180)
This occurs as part of the inital clock tree update of child clock nodes
where new_rate could be 0 for non functional clocks.
Fixes: b4761198bf ("CLK: ti: add support for ti divider-clock")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 067bb1741c upstream.
In some cases, clocks can switch their parent with clk_set_rate, for
example clk_mux can do this in some cases. Current implementation of
clk_change_rate uses un-safe list iteration on the clock children, which
will cause wrong clocks to be parsed in case any of the clock children
change their parents during the change rate operation. Fixed by using
the safe list iterator instead.
The problem was detected due to some divide by zero errors generated
by clock init on dra7-evm board, see discussion under
http://article.gmane.org/gmane.linux.ports.arm.kernel/349180 for details.
Fixes: 71472c0c06 ("clk: add support for clock reparent on set_rate")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20411dad75 upstream.
Check for valid parameters in check rate. Else, we end up getting
errors.
This occurs as part of the inital clock tree update of child clock
nodes where new_rate could be 0 for non functional clocks.
Fixes: 9ac33b0ce8 (" CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ABE DPLL frequency need to be lowered from 361267200
to 180633600 to facilitate the ATL requironments.
The dpll_abe_m2x2_ck clock need to be set to double
of ABE DPLL rate in order to have correct clocks
for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that did
not boot under certain configurations. Other fixes are the result of
changes to the clock core introduced in 3.15 that had subtle impacts on
the clock drivers.
There are no fixes to the clock framework core in this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTwrM0AAoJEDqPOy9afJhJGtgP/j99sWo/P/Q+wkybYfvlAvYF
UC69GdYIV4PpHXq7JDrs9n48cf8Cte6QsYTVxFipmcBKiZrxoH1Ft6AZk0XuzHPb
bONgwlxPH03Xy/pm1aWO3AX7zMiOzTlxAqPuisJa4rbBty3XOQqEFyuJnHEW2m59
L754YWvT6dAzYyU1LQE4iSGPD8Dmh/oVvjg17+hM6//yM3fspYA3gzui/Lj4L1sx
QL0FFo6SJ4vvn9MMen+/UgZZ2G25fR4e0AONvz+rzBA2fmCGoQbNs26Iyi+MpEtg
DlXGcMTwl3Cj+mulalAIxBJ441KDtqm6TZ7iIEuaBUDCxFxNIuvup8FuMIAjDlt4
+V6OTFA7tlYr8UGQ/KRiTTgd6TKKUu9FpKmYOq/K1VZZls6m2hVTWvcwZ/217VYq
cimnVrHGs22vXhYKL2S3/TWfioiVP3vN08+NQOI5IRhYfXm+oPMuWwahHU/VnY2C
AaAUaHgqSlLmIbGqgvsjDQglRyGajs8oz/SfDuxXTBClc/6lu4ENNL9UQffdBTV4
IfrU+ALRR+CjPtLOHUTrLIHldGbn40Ff0fdKyJ/iGtdE+iiNJcnoU2G0uuhMP4eP
JpAMY2XrzZWGVJegjvg1m1Qfv85FBJhUB6+T5wIFYwKwBPzSf/yx0YTt+R0mp7Lg
g0CWTO3SoDeKDSK2Yzr2
=6n8W
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
Samsung, ST & TI. Most of them are of the "this hardware won't work
without this fix" variety, including patches that fix platforms that
did not boot under certain configurations. Other fixes are the result
of changes to the clock core introduced in 3.15 that had subtle
impacts on the clock drivers.
There are no fixes to the clock framework core in this pull request"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: spear3xx: Set proper clock parent of uart1/2
clk: spear3xx: Use proper control register offset
clk: qcom: HDMI source sel is 3 not 2
clk: sunxi: fix devm_ioremap_resource error detection code
clk: s2mps11: Fix double free corruption during driver unbind
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: exynos5420: Remove aclk66_peric from the clock tree description
clk/exynos5250: fix bit number for tv sysmmu clock
clk: s3c64xx: Hookup SPI clocks correctly
clk: samsung: exynos4: Remove SRC_MASK_ISP gates
clk: samsung: add more aliases for s3c24xx
clk: samsung: fix several typos to fix boot on s3c2410
clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
clk: ti: dra7: return error code in failure case
clk: ti: apll: not allocating enough data
The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.
Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adds IDs for MUX clocks to be used by power domain for MFC
for doing re-parenting while pd on/off.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The HDMI PLL input to the tv mux is supposed to be 3, not 2. Fix
the code so that we can properly select the HDMI PLL.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This pull request contains fixes for various issues found while testing
-rc versions of Linux 3.16. Mostly two kinds of patches:
* Fixes of incorrectly defined clocks
1) a37c82a clk: samsung: exynos4: Remove SRC_MASK_ISP gates
Issue present since v3.10.
2) 0b1643b clk/exynos5250: fix bit number for tv sysmmu clock
Issue present since v3.16.
3) 44ff025 clk: exynos5420: Remove aclk66_peric from the clock tree description
Issue present since v3.11.
* Adding things missed by original patches
1) cec1cde clk: samsung: fix several typos to fix boot on s3c2410
2) 34ece9e clk: samsung: add more aliases for s3c24xx
Both issues present since the driver was added in v3.16.
3) a92dda4 clk: s3c64xx: Hookup SPI clocks correctly
Issue present since v3.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=eE4V
-----END PGP SIGNATURE-----
Merge tag 'for_3.16/samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes-samsung
Samsung clock fixes for v3.16.
This pull request contains fixes for various issues found while testing
-rc versions of Linux 3.16. Mostly two kinds of patches:
* Fixes of incorrectly defined clocks
1) a37c82a clk: samsung: exynos4: Remove SRC_MASK_ISP gates
Issue present since v3.10.
2) 0b1643b clk/exynos5250: fix bit number for tv sysmmu clock
Issue present since v3.16.
3) 44ff025 clk: exynos5420: Remove aclk66_peric from the clock tree description
Issue present since v3.11.
* Adding things missed by original patches
1) cec1cde clk: samsung: fix several typos to fix boot on s3c2410
2) 34ece9e clk: samsung: add more aliases for s3c24xx
Both issues present since the driver was added in v3.16.
3) a92dda4 clk: s3c64xx: Hookup SPI clocks correctly
Issue present since v3.12.
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The "aclk66_peric" clock is a gate clock with a whole bunch of gates
underneath it. This big gate isn't very useful to include in our
clock tree. If any of the children need to be turned on then the big
gate will need to be on anyway. ...and there are plenty of other "big
gates" that aren't described in our clock tree, some of which shut off
collections of clocks that have no relationship in the hierarchy so
are hard to model.
"aclk66_peric" is causing earlyprintk problems since it gets disabled
as part of the boot process, so let's just remove it.
Strangely (and for no good reason) this clock is exported as part of
the common clock bindings. Remove it since there are no in-kernel
device trees using it and no reason anyone out of tree should refer to
it either.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Change bit from 2 to 9 for tv (mixer) sysmmu clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
In the move to this clock driver the hookups for the SPI clocks were
dropped, which causes my system Cragganmore (s3c6410 based) to be unable
to locate any spibus clocks. This patch adds them back in.
When taking the clock from the epll clock (SCLK) the rates on the SPI
bus are incorrect, this needs further debugging but the hookup here
should be correct and the problem should be else where.
The USBCLK case has been dropped because this requires the USB PHY to be
enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
ISP special clocks have dedicated gating registers and so MUX SRC_MASK
register should not be used. This patch fixes the problem of
Exynos4x12-based boards freezing on system suspend, because those
mux outputs need not to be masked while suspending.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
There's a several typos in a driver: 2410 instead of S3C2410
and wrong argument to ARRAY_SIZE(). They prevent s3c2410
from properly booting.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
When setting the rate of a clock, by default the clock framework will
change the parent of the clock to the most suitable one in
__clk_mux_determine_rate() (most suitable by looking at the clock rate).
This is a rather dangerous default, and causes problems on AM43x when
using display and ethernet. There are multiple ways to select the clock
muxes on AM43x, and some of those clock paths have the same source
clocks for display and ethernet. When changing the clock rate for the
display subsystem, the clock framework decides to change the display mux
from the dedicated display PLL to a shared PLL which is used by the
ethernet, and then changes the rate of the shared PLL, breaking the
ethernet.
As I don't think there ever is a case where we want the clock framework
to automatically change the parent clock of a clock mux, this patch sets
the CLK_SET_RATE_NO_REPARENT for all ti,mux-clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add a returned error code in the MAX_APLL_WAIT_TRIES case. Remove the
updating of the return variable r to 0 if MAX_APLL_WAIT_TRIES is not yet
reached, because r is already 0 at this point.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is a cut and paste bug here which will lead to memory corruption
because we don't allocate enough data.
Fixes: 4d008589e2 ('CLK: TI: APLL: add support for omap2 aplls')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
3.16. They are simply fixes and code refactoring for the OMAP clock
drivers. The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=9/Iv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
The PRCM (Power/Reset/Clock Management) unit provides several clock
devices:
- AR100 clk: used to clock the Power Management co-processor
- AHB0 clk: used to clock the AHB0 bus
- APB0 clk and gates: used to clk peripherals connected to the APB0 bus
Add support for these clks in a separate driver so that they can be probed
as platform devices instead of registered during early init.
This is needed to be able to probe PRCM MFD subdevices.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Prevent the SDRAM controller from being gated by force-enabling it in the
machine code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Right now, AHB is an indirect child clock of the CPU clock. If that
happens to change, since the CPU clock has no other consumers declared
in Linux, it would be shut down, which is not really a good idea.
Prevent this by forcing it enabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we start to have a lot of clocks to protect, some of them in a
few SoCs only, it becomes difficult to handle the clock protection
without having to add per machine exceptions.
Add per-SoC data to tell which clock to leave enabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we have a folder of our own, we can actually make use of it by
splitting the huge clock file into several sub drivers.
The gmac clock is pretty easy to deal with, since it's pretty much
isolated and doesn't have any dependency on the other clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we have a folder of our own, we can actually make use of it by
splitting the huge clock file into several sub drivers.
The main oscillator is pretty easy to deal with, since it's pretty much
isolated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Callers of clk_put must disable the clock first. This also means that
as long as the clock is enabled the driver should hold a reference to
that clock. Hence, the call to clk_put here are bogus and should be
removed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
