The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423 ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The properties #address-cells and #size-cells are only useful if there
is a ranges property or child nodes with "reg" properties.
This fixes a W=1 warning:
arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts:51.22-72.4: Warning (avoid_unnecessary_addr_size): /soc/i2c@ffc04000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges", "dma-ranges" or child "reg" property
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Drop SVM's direct TLB flush when CR4.PGE is toggled and NPT is enabled, as
KVM already guarantees TLBs are flushed appropriately.
For the call from cr_trap(), kvm_post_set_cr4() requests TLB_FLUSH_GUEST
(which is a superset of TLB_FLUSH_CURRENT) when CR4.PGE is toggled,
regardless of whether or not KVM is using TDP.
The calls from nested_vmcb02_prepare_save() and nested_svm_vmexit() are
checking guest (L2) vs. host (L1) CR4, and so a flush is unnecessary as L2
is defined to use a different ASID (from L1's perspective).
Lastly, the call from svm_set_cr0() passes in the current CR4 value, i.e.
can't toggle PGE.
Link: https://lore.kernel.org/r/20241127235312.4048445-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Define sev_{,es_,snp_}guest() as "false" when SEV is disabled via Kconfig,
i.e. when CONFIG_KVM_AMD_SEV=n. Despite the helpers being __always_inline,
gcc-12 is somehow incapable of realizing that the return value is a
compile-time constant and generates sub-optimal code.
Opportunistically clump the paths together to reduce the amount of
ifdeffery.
No functional change intended.
Link: https://lore.kernel.org/r/20241127234659.4046347-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
The values returned by the driver after processing the contents of the
Temperature Result and the Temperature Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect.
According to the TMP512 and TMP513 datasheets, the Temperature Result (08h
to 0Bh) and Limit (11h to 14h) Registers are 13-bit two's complement
integer values, shifted left by 3 bits. The value is scaled by 0.0625
degrees Celsius per bit. E.g., if regval = 1 1110 0111 0000 000, the
output should be -25 degrees, but the driver will return +487 degrees.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-4-m.masimov@maxima.ru
[groeck: fixed description line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The value returned by the driver after processing the contents of the
Current Register does not correspond to the TMP512/TMP513 specifications.
A raw register value is converted to a signed integer value by a sign
extension in accordance with the algorithm provided in the specification,
but due to the off-by-one error in the sign bit index, the result is
incorrect. Moreover, negative values will be reported as large positive
due to missing sign extension from u32 to long.
According to the TMP512 and TMP513 datasheets, the Current Register (07h)
is a 16-bit two's complement integer value. E.g., if regval = 1000 0011
0000 0000, then the value must be (-32000 * lsb), but the driver will
return (33536 * lsb).
Fix off-by-one bug, and also cast data->curr_lsb_ua (which is of type u32)
to long to prevent incorrect cast for negative values.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-3-m.masimov@maxima.ru
[groeck: Fixed description line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The values returned by the driver after processing the contents of the
Shunt Voltage Register and the Shunt Limit Registers do not correspond to
the TMP512/TMP513 specifications. A raw register value is converted to a
signed integer value by a sign extension in accordance with the algorithm
provided in the specification, but due to the off-by-one error in the sign
bit index, the result is incorrect. Moreover, the PGA shift calculated with
the tmp51x_get_pga_shift function is relevant only to the Shunt Voltage
Register, but is also applied to the Shunt Limit Registers.
According to the TMP512 and TMP513 datasheets, the Shunt Voltage Register
(04h) is 13 to 16 bit two's complement integer value, depending on the PGA
setting. The Shunt Positive (0Ch) and Negative (0Dh) Limit Registers are
16-bit two's complement integer values. Below are some examples:
* Shunt Voltage Register
If PGA = 8, and regval = 1000 0011 0000 0000, then the decimal value must
be -32000, but the value calculated by the driver will be 33536.
* Shunt Limit Register
If regval = 1000 0011 0000 0000, then the decimal value must be -32000, but
the value calculated by the driver will be 768, if PGA = 1.
Fix sign bit index, and also correct misleading comment describing the
tmp51x_get_pga_shift function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 59dfa75e5d ("hwmon: Add driver for Texas Instruments TMP512/513 sensor chips.")
Signed-off-by: Murad Masimov <m.masimov@maxima.ru>
Link: https://lore.kernel.org/r/20241216173648.526-2-m.masimov@maxima.ru
[groeck: Fixed description and multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On a first glance it isn't obvious why calling kvm_tdp_page_fault() in
kvm_mmu_do_page_fault() is special cased, as the general case of using
an indirect case would result in calling of kvm_tdp_page_fault()
anyway.
Add a comment to explain the reason.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20241108161416.28552-1-jgross@suse.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Pass the target vCPU to the hwapic_isr_update() vendor hook so that VMX
can defer the update until after nested VM-Exit if an EOI for L1's vAPIC
occurs while L2 is active.
Note, commit d39850f57d ("KVM: x86: Drop @vcpu parameter from
kvm_x86_ops.hwapic_isr_update()") removed the parameter with the
justification that doing so "allows for a decent amount of (future)
cleanup in the APIC code", but it's not at all clear what cleanup was
intended, or if it was ever realized.
No functional change intended.
Cc: stable@vger.kernel.org
Reviewed-by: Chao Gao <chao.gao@intel.com>
Tested-by: Chao Gao <chao.gao@intel.com>
Link: https://lore.kernel.org/r/20241128000010.4051275-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Now that KVM takes vcpu->mutex inside kvm->lock when creating a vCPU, drop
the hack to manually inform lockdep of the kvm->lock => vcpu->mutex
ordering.
This effectively reverts commit 42a90008f8 ("KVM: Ensure lockdep knows
about kvm->lock vs. vcpu->mutex ordering rule").
Cc: Oliver Upton <oliver.upton@linux.dev>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
WARN once instead of triggering a BUG if xa_insert() fails because it
encountered an existing entry. While KVM guarantees there should be no
existing entry, there's no reason to BUG the kernel, as KVM needs to
gracefully handle failure anyways.
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Now that KVM loads from vcpu_array if and only if the target index is
valid with respect to online_vcpus, i.e. now that it is safe to erase a
not-fully-onlined vCPU entry, revert to storing into vcpu_array before
success is guaranteed.
If xa_store() fails, which _should_ be impossible, then putting the vCPU's
reference to 'struct kvm' results in a refcounting bug as the vCPU fd has
been installed and owns the vCPU's reference.
This was found by inspection, but forcing the xa_store() to fail
confirms the problem:
| Unable to handle kernel paging request at virtual address ffff800080ecd960
| Call trace:
| _raw_spin_lock_irq+0x2c/0x70
| kvm_irqfd_release+0x24/0xa0
| kvm_vm_release+0x1c/0x38
| __fput+0x88/0x2ec
| ____fput+0x10/0x1c
| task_work_run+0xb0/0xd4
| do_exit+0x210/0x854
| do_group_exit+0x70/0x98
| get_signal+0x6b0/0x73c
| do_signal+0xa4/0x11e8
| do_notify_resume+0x60/0x12c
| el0_svc+0x64/0x68
| el0t_64_sync_handler+0x84/0xfc
| el0t_64_sync+0x190/0x194
| Code: b9000909 d503201f 2a1f03e1 52800028 (88e17c08)
Practically speaking, this is a non-issue as xa_store() can't fail, absent
a nasty kernel bug. But the code is visually jarring and technically
broken.
This reverts commit afb2acb2e3.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michal Luczaj <mhal@rbox.co>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marc Zyngier <maz@kernel.org>
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-5-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
During vCPU creation, acquire vcpu->mutex prior to exposing the vCPU to
userspace, and hold the mutex until online_vcpus is bumped, i.e. until the
vCPU is fully online from KVM's perspective.
To ensure asynchronous vCPU ioctls also wait for the vCPU to come online,
explicitly check online_vcpus at the start of kvm_vcpu_ioctl(), and take
the vCPU's mutex to wait if necessary (having to wait for any ioctl should
be exceedingly rare, i.e. not worth optimizing).
Reported-by: Will Deacon <will@kernel.org>
Reported-by: Michal Luczaj <mhal@rbox.co>
Link: https://lore.kernel.org/all/20240730155646.1687-1-will@kernel.org
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Explicitly check that there is at least online vCPU before iterating over
all vCPUs. Because the max index is an unsigned long, passing "0 - 1" in
the online_vcpus==0 case results in xa_for_each_range() using an unlimited
max, i.e. allows it to access vCPU0 when it shouldn't. This will allow
KVM to safely _erase_ from vcpu_array if the last stages of vCPU creation
fail, i.e. without generating a use-after-free if a different task happens
to be concurrently iterating over all vCPUs.
Note, because xa_for_each_range() is a macro, kvm_for_each_vcpu() subtly
reloads online_vcpus after each iteration, i.e. adding an extra load
doesn't meaningfully impact the total cost of iterating over all vCPUs.
And because online_vcpus is never decremented, there is no risk of a
reload triggering a walk of the entire xarray.
Cc: Will Deacon <will@kernel.org>
Cc: Michal Luczaj <mhal@rbox.co>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Explicitly verify the target vCPU is fully online _prior_ to clamping the
index in kvm_get_vcpu(). If the index is "bad", the nospec clamping will
generate '0', i.e. KVM will return vCPU0 instead of NULL.
In practice, the bug is unlikely to cause problems, as it will only come
into play if userspace or the guest is buggy or misbehaving, e.g. KVM may
send interrupts to vCPU0 instead of dropping them on the floor.
However, returning vCPU0 when it shouldn't exist per online_vcpus is
problematic now that KVM uses an xarray for the vCPUs array, as KVM needs
to insert into the xarray before publishing the vCPU to userspace (see
commit c5b0775491 ("KVM: Convert the kvm->vcpus array to a xarray")),
i.e. before vCPU creation is guaranteed to succeed.
As a result, incorrectly providing access to vCPU0 will trigger a
use-after-free if vCPU0 is dereferenced and kvm_vm_ioctl_create_vcpu()
bails out of vCPU creation due to an error and frees vCPU0. Commit
afb2acb2e3 ("KVM: Fix vcpu_array[0] races") papered over that issue, but
in doing so introduced an unsolvable teardown conundrum. Preventing
accesses to vCPU0 before it's fully online will allow reverting commit
afb2acb2e3, without re-introducing the vcpu_array[0] UAF race.
Fixes: 1d487e9bf8 ("KVM: fix spectrev1 gadgets")
Cc: stable@vger.kernel.org
Cc: Will Deacon <will@kernel.org>
Cc: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20241009150455.1057573-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
If mounted with sparseread option, ceph_direct_read_write() ends up
making an unnecessarily allocation for O_DIRECT writes.
Fixes: 03bc06c7b0 ("ceph: add new mount option to enable sparse reads")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
The bvecs array which is allocated in iter_get_bvecs_alloc() is leaked
and pages remain pinned if ceph_alloc_sparse_ext_map() fails.
There is no need to delay the allocation of sparse_ext map until after
the bvecs array is set up, so fix this by moving sparse_ext allocation
a bit earlier. Also, make a similar adjustment in __ceph_sync_read()
for consistency (a leak of the same kind in __ceph_sync_read() has been
addressed differently).
Cc: stable@vger.kernel.org
Fixes: 03bc06c7b0 ("ceph: add new mount option to enable sparse reads")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
This patch refines the read logic in __ceph_sync_read() to ensure more
predictable and efficient behavior in various edge cases.
- Return early if the requested read length is zero or if the file size
(`i_size`) is zero.
- Initialize the index variable (`idx`) where needed and reorder some
code to ensure it is always set before use.
- Improve error handling by checking for negative return values earlier.
- Remove redundant encrypted file checks after failures. Only attempt
filesystem-level decryption if the read succeeded.
- Simplify leftover calculations to correctly handle cases where the
read extends beyond the end of the file or stops short. This can be
hit by continuously reading a file while, on another client, we keep
truncating and writing new data into it.
- This resolves multiple issues caused by integer and consequent buffer
overflow (`pages` array being accessed beyond `num_pages`):
- https://tracker.ceph.com/issues/67524
- https://tracker.ceph.com/issues/68980
- https://tracker.ceph.com/issues/68981
Cc: stable@vger.kernel.org
Fixes: 1065da21e5 ("ceph: stop copying to iter at EOF on sync reads")
Reported-by: Luis Henriques (SUSE) <luis.henriques@linux.dev>
Signed-off-by: Alex Markuze <amarkuze@redhat.com>
Reviewed-by: Viacheslav Dubeyko <Slava.Dubeyko@ibm.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
It becomes a path component, so it shouldn't exceed NAME_MAX
characters. This was hardened in commit c152737be2 ("ceph: Use
strscpy() instead of strcpy() in __get_snap_name()"), but no actual
check was put in place.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
If the full path to be built by ceph_mdsc_build_path() happens to be
longer than PATH_MAX, then this function will enter an endless (retry)
loop, effectively blocking the whole task. Most of the machine
becomes unusable, making this a very simple and effective DoS
vulnerability.
I cannot imagine why this retry was ever implemented, but it seems
rather useless and harmful to me. Let's remove it and fail with
ENAMETOOLONG instead.
Cc: stable@vger.kernel.org
Reported-by: Dario Weißer <dario@cure53.de>
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Reviewed-by: Alex Markuze <amarkuze@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
In two `break` statements, the call to ceph_release_page_vector() was
missing, leaking the allocation from ceph_alloc_page_vector().
Instead of adding the missing ceph_release_page_vector() calls, the
Ceph maintainers preferred to transfer page ownership to the
`ceph_osd_request` by passing `own_pages=true` to
osd_req_op_extent_osd_data_pages(). This requires postponing the
ceph_osdc_put_request() call until after the block that accesses the
`pages`.
Cc: stable@vger.kernel.org
Fixes: 03bc06c7b0 ("ceph: add new mount option to enable sparse reads")
Fixes: f0fe1e54cf ("ceph: plumb in decryption during reads")
Signed-off-by: Max Kellermann <max.kellermann@ionos.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
When function tracing and function graph tracing are both enabled (in
different instances) the "parent" of some of the function tracing events
is "return_to_handler" which is the trampoline used by function graph
tracing. To fix this, ftrace_get_true_parent_ip() was introduced that
returns the "true" parent ip instead of the trampoline.
To do this, the ftrace_regs_get_stack_pointer() is used, which uses
kernel_stack_pointer(). The problem is that microblaze does not implement
kerenl_stack_pointer() so when function graph tracing is enabled, the
build fails. But microblaze also does not enabled HAVE_DYNAMIC_FTRACE_WITH_ARGS.
That option has to be enabled by the architecture to reliably get the
values from the fregs parameter passed in. When that config is not set,
the architecture can also pass in NULL, which is not tested for in that
function and could cause the kernel to crash.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jeff Xie <jeff.xie@linux.dev>
Link: https://lore.kernel.org/20241216164633.6df18e87@gandalf.local.home
Fixes: 60b1f578b5 ("ftrace: Get the true parent ip for function tracer")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The sama7g5 QSPI controller uses dedicated clocks for the
QSPI Controller Interface and the QSPI Controller Core, and
requires synchronization before accessing registers or bit
fields.
QSPI_SR.SYNCBSY must be zero before accessing any of the bits:
QSPI_CR.QSPIEN, QSPI_CR.QSPIDIS, QSPI_CR.SRFRSH, QSPI_CR.SWRST,
QSPI_CR.UPDCFG, QSPI_CR.STTFR, QSPI_CR.RTOUT, QSPI_CR.LASTXFER.
Also, the QSPI controller core configuration can be updated by
writing the QSPI_CR.UPDCFG bit to ‘1’. This is needed by the
following registers: QSPI_MR, QSPI_SCR, QSPI_IAR, QSPI_WICR,
QSPI_IFR, QSPI_RICR, QSPI_SMR, QSPI_SKR,QSPI_REFRESH, QSPI_WRACNT
QSPI_PCALCFG.
The Octal SPI supports frequencies up to 200 MHZ DDR. The need
for output impedance calibration arises. To avoid the degradation
of the signal quality, a PAD calibration cell is used to adjust
the output impedance to the driven I/Os.
The transmission flow requires different sequences for setting
the configuration and for the actual transfer, than what is in
the sama5d2 and sam9x60 versions of the IP. Different interrupts
are handled. aq->ops->set_cfg() and aq->ops->transfer() are
introduced to help differentiating the flows.
Tested single and octal SPI mode with mx66lm1g45g.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211214133404.121739-1-tudor.ambarus@microchip.com
[varshini.rajendran@microchip.com: Fixed conflicts and ported to 6.1.4]
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
[ csokas.bence: Forward-port to master and address feedback ]
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241128174316.3209354-3-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor the code to introduce an ops struct, to prepare for merging
support for later SoCs, such as SAMA7G5. This code was based on the
vendor's kernel (linux4microchip). Cc'ing original contributors.
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20241128174316.3209354-2-csokas.bence@prolan.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Add handling of clock related to secondary MI2S_RX in startup, shutdown
and hw params routines. The handing of MI2S_TX and SEC_MI2S clock is
already there so this requires only placing SECONDARY_MI2S_RX in the
correct switch-case choices.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241205023344.2232529-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest released firmware supports reading firmware interface version
from registers directly. The driver's probe routine reads the major and
minor version numbers. If the firmware interface is not compatible with
the driver, the driver's probe routine returns failure.
Co-developed-by: Min Ma <min.ma@amd.com>
Signed-off-by: Min Ma <min.ma@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213232933.1545388-5-lizhi.hou@amd.com
Add SET_STATE ioctl to configure device power mode for aie2 device.
Three modes are supported initially.
POWER_MODE_DEFAULT: Enable clock gating and set DPM (Dynamic Power
Management) level to value which has been set by resource solver or
maximum DPM level the device supports.
POWER_MODE_HIGH: Enable clock gating and set DPM level to maximum DPM
level the device supports.
POWER_MODE_TURBO: Disable clock gating and set DPM level to maximum DPM
level the device supports.
Disabling clock gating means all clocks always run on full speed. And
the different clock frequency are used based on DPM level been set.
Initially, the driver set the power mode to default mode.
Co-developed-by: Narendra Gutta <VenkataNarendraKumar.Gutta@amd.com>
Signed-off-by: Narendra Gutta <VenkataNarendraKumar.Gutta@amd.com>
Co-developed-by: George Yang <George.Yang@amd.com>
Signed-off-by: George Yang <George.Yang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213232933.1545388-4-lizhi.hou@amd.com
Switch mailbox message id and hardware context id management over from
the idr api to the xarray api.
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213232933.1545388-3-lizhi.hou@amd.com
Bastien Curutchet says:
====================
This patch series continues the work to migrate the script tests into
prog_tests.
test_xdp_meta.sh uses the BPF programs defined in progs/test_xdp_meta.c
to do a simple XDP/TC functional test that checks the metadata
allocation performed by the bpf_xdp_adjust_meta() helper.
This is already partly covered by two tests under prog_tests/:
- xdp_context_test_run.c uses bpf_prog_test_run_opts() to verify the
validity of the xdp_md context after a call to bpf_xdp_adjust_meta()
- xdp_metadata.c ensures that these meta-data can be exchanged through
an AF_XDP socket.
However test_xdp_meta.sh also verifies that the meta-data initialized
in the struct xdp_md is forwarded to the struct __sk_buff used by BPF
programs at 'TC level'. To cover this, I add a test case in
xdp_context_test_run.c that uses the same BPF programs from
progs/test_xdp_meta.c.
Changes in v2:
- Add missing close_netns()
- Use a unique 'close' label
- Link to v1: https://lore.kernel.org/r/20241206-xdp_meta-v1-0-5c150618f6e9@bootlin.com
====================
Link: https://patch.msgid.link/20241213-xdp_meta-v2-0-634582725b90@bootlin.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
test_xdp_meta.sh can't be used by the BPF CI.
Migrate test_xdp_meta.sh in a new test case in xdp_context_test_run.c.
It uses the same BPF programs located in progs/test_xdp_meta.c and the
same network topology.
Remove test_xdp_meta.sh and its Makefile entry.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20241213-xdp_meta-v2-2-634582725b90@bootlin.com
of_find_node_opts_by_path() fails to find OF device node when its
@path parameter have pattern below:
"alias-name/node-name-1/.../node-name-N:options".
The reason is that alias name length calculated by the API is wrong, as
explained by example below:
"testcase-alias/phandle-tests/consumer-a:testaliasoption".
^ ^ ^
0 14 39
The right length of alias 'testcase-alias' is 14, but the result worked
out by the API is 39 which is obvious wrong.
Fix by using index of either '/' or ':' as the length who comes earlier.
Fixes: 75c28c09af ("of: add optional options parameter to of_find_node_by_path()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241216-of_core_fix-v2-1-e69b8f60da63@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
To test of_find_node_opts_by_path() take @path argument with pattern:
"alias-name/node-name-1/.../node-name-N:options", for example:
"testcase-alias/phandle-tests/consumer-a:testaliasoption"
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241216-of_core_fix-v2-2-e69b8f60da63@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
SEC("t") and SEC("x") can't be loaded by the __load() helper.
Rename these sections SEC("tc") and SEC("xdp") so they can be
interpreted by the __load() helper in upcoming patch.
Update the test_xdp_meta.sh to fit these new names.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20241213-xdp_meta-v2-1-634582725b90@bootlin.com
The DUAL_QUEUE_WA tells the GuC to not allow concurrent submissions
on RCS and CCSes with different address spaces, which on DG2 is
required as a WA for an HW bug. On newer platforms, this block has
been moved in HW at the CS level, by stalling the RCS/CCS context
switch when one of the other RCS/CCSes is busy with a different
address space. While functionally correct, having a submission
stalled on the HW limits the GuC ability to shuffle things around and
can cause complications if the non-stalled submission runs for a long
time, because the GuC doesn't know that the stalled submission isn't
actually running and might declare it as hung. Therefore, we enable
the DUAL_QUEUE_WA on all newer platforms to move management back to
the GuC.
Note that the GuC specs also recommend enabling this for all platforms
starting from MTL that have a CCS.
v2: only apply the WA on GTs that have CCS engines
v3: split comment (Jonathan)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Jesus Narvaez <jesus.narvaez@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213181012.2178794-1-daniele.ceraolospurio@intel.com
A bug was discovered where the idle shadow stacks were not initialized
for offline CPUs when starting function graph tracer, and when they came
online they were not traced due to the missing shadow stack. To fix
this, the idle task shadow stack initialization was moved to using the
CPU hotplug callbacks. But it removed the initialization when the
function graph was enabled. The problem here is that the hotplug
callbacks are called when the CPUs come online, but the idle shadow
stack initialization only happens if function graph is currently
active. This caused the online CPUs to not get their shadow stack
initialized.
The idle shadow stack initialization still needs to be done when the
function graph is registered, as they will not be allocated if function
graph is not registered.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20241211135335.094ba282@batman.local.home
Fixes: 2c02f7375e ("fgraph: Use CPU hotplug mechanism to initialize idle shadow stacks")
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Closes: https://lore.kernel.org/all/CACRpkdaTBrHwRbbrphVy-=SeDz6MSsXhTKypOtLrTQ+DgGAOcQ@mail.gmail.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Commit 'cpupower: Make TSC read per CPU for Mperf monitor' (c2adb1877b)
changes TSC counter reads per cpu, but left time diff global (from start
of all cpus to end of all cpus), thus diff(time) is too large for a
cpu's tsc counting, resulting in far less than acutal TSC_Mhz and thus
`cpupower monitor` showing far less than actual cpu realtime frequency.
/proc/cpuinfo shows frequency:
cat /proc/cpuinfo | egrep -e 'processor' -e 'MHz'
...
processor : 171
cpu MHz : 4108.498
...
before fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.77| 99.23| 2279|| 0.00| 0.00| 0.00
after fix (System 100% busy):
| Mperf || Idle_Stats
CPU| C0 | Cx | Freq || POLL | C1 | C2
171| 0.46| 99.54| 4095|| 0.00| 0.00| 0.00
Fixes: c2adb1877b ("cpupower: Make TSC read per CPU for Mperf monitor")
Signed-off-by: He Rongguang <herongguang@linux.alibaba.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
With `long` mapped to `isize`, `size_t`/`__kernel_size_t` mapped to
`usize` and `char` mapped to `u8`, many of the existing casts are no
longer necessary.
Signed-off-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240913213041.395655-6-gary@garyguo.net
[ Moved `uaccess` changes to the previous commit, since they were
irrefutable patterns that Rust >= 1.82.0 warns about. Removed a
couple casts that now use `c""` literals. Rebased on top of
`rust-next`. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
The following FFI types are replaced compared to `core::ffi`:
1. `char` type is now always mapped to `u8`, since kernel uses
`-funsigned-char` on the C code. `core::ffi` maps it to platform
default ABI, which can be either signed or unsigned.
2. `long` is now always mapped to `isize`. It's very common in the
kernel to use `long` to represent a pointer-sized integer, and in
fact `intptr_t` is a typedef of `long` in the kernel. Enforce this
mapping rather than mapping to `i32/i64` depending on platform can
save us a lot of unnecessary casts.
Signed-off-by: Gary Guo <gary@garyguo.net>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20240913213041.395655-5-gary@garyguo.net
[ Moved `uaccess` changes from the next commit, since they were
irrefutable patterns that Rust >= 1.82.0 warns about. Reworded
slightly and reformatted a few documentation comments. Rebased on
top of `rust-next`. Added the removal of two casts to avoid Clippy
warnings. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
In the last kernel cycle we migrated most of the `core::ffi` cases in
commit d072acda48 ("rust: use custom FFI integer types"):
Currently FFI integer types are defined in libcore. This commit
creates the `ffi` crate and asks bindgen to use that crate for FFI
integer types instead of `core::ffi`.
This commit is preparatory and no type changes are made in this
commit yet.
Finish now the few remaining/new cases so that we perform the actual
remapping in the next commit as planned.
Acked-by: Jocelyn Falempe <jfalempe@redhat.com> # drm
Link: https://lore.kernel.org/rust-for-linux/CANiq72m_rg42SvZK=bF2f0yEoBLVA33UBhiAsv8THhVu=G2dPA@mail.gmail.com/
Link: https://lore.kernel.org/all/cc9253fa-9d5f-460b-9841-94948fb6580c@redhat.com/
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Now everything in ath12k is in place and we can enable Multi-Link Operation
(MLO) in the driver. For now it's only enabled for QCN9274 with firmware having
ATH12K_FW_FEATURE_MLO feature bit set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the QMI host capability, the device index, the number of local
links, and the corresponding hardware link IDs are sent. The hardware link ID
assignment is based on the local variable `hw_link_id`, which starts from 0 and
ranges up to `num_local_links` in the device. Starting from 0 is not ideal
because it can result in the same link ID being assigned to different devices
in certain scenarios (e.g., split MAC). Additionally, for multi link
operations the firmware expects the hardware link IDs in the same order as the
Wireless Serial Interface (WSI) connection.
Hence, for MLO to function seamlessly, the hardware link IDs across devices
need to be unique and should follow the order of the WSI connection. To address
this, a previous change read the WSI index from the Device Tree (DT) and stored
it. Use this WSI index to determine the starting hardware link IDs for each
device, ensuring uniqueness and correct order across all devices.
While at it, add debug prints to clearly show the MLO capability advertisement
sent during QMI host capability exchange.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To maintain backward compatibility with older firmware versions, introduce a
new feature bit, ATH12K_FW_FEATURE_MLO, to identify whether the firmware
supports MLO. If the firmware-X.bin does not have this bit advertised in the
feature, then MLO capability in the host will be disabled.
This applies only for QCN9274 chipsets.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the function ath12k_htt_mlo_offset_event_handler(), it is possible that
the ar is not yet active (started). The function
ath12k_mac_get_ar_by_pdev_id() only searches for active pdev, so a NULL
return is possible. Therefore, there is no need to print a warning,
instead, just silently discard the message.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, certain WMI events are frequently received by the host. Since
the host lacks the logic to process these events, the console is flooded
with ‘Unknown eventid:’ debug messages.
To address this, handle these events gracefully without printing debug
messages. There is already a block of event IDs that are ignored with a debug
print. However, this new type of event occurs more frequently, so no debug
print is necessary, and handling it should be a no-op.
While at it, re-arrange the code so that all Unknown event IDs are towards
the end of the switch block.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When operating as an ML station, mac80211 initially activates only one link in
the driver until the peer is authorized. Once the state changes to authorized,
the driver should call mac80211 API to activate all other partner links.
Before doing so, mac80211 checks if the driver supports activating links via
the can_activate_links mac80211_ops. Therefore, add support for this
mac80211_ops and call the API to activate the links once the state changes to
authorized.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the hardware scan is initiated in the driver on scan link (15).
After mapping to the appropriate radio based on the scan frequency, the vdev is
created and the scan begins. However, the vdev is only deleted when channel
assignment is about to occur after the scan. Additionally, it is also deleted
if a new scan is requested on the same interface but the underlying radio
differs in the new request.
This imbalance leads to various hardware scan issues, especially when a non-MLO
and MLO combination exists. In such cases, the latter tries to skip the scan
and proceed with channel assignment while the former is still scanning, causing
a firmware assert.
To address this issue, symmetrize the scan vdev creation and deletion during
hardware scan operations. This means creating a vdev when the scan starts and
deleting it once the scan is completed or aborted.
While at this, add a few debug prints in scan handling and a few empty lines
for better code read.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
mac80211 expects link_id in some scenarios or else the packet might
get dropped. Hence, add link_id information before delivering the skb.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-10-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the ath12k_mac_hw_register() function's context, ar is an iterator
variable, and there is no assurance that the last ar will be the one with
6 GHz enabled. Therefore, checking directly ar->supports_6ghz outside the
loop is not appropriate.
Additionally, 6 GHz lacks HT capabilities. To obtain the super set of
HT capabilities across all grouped radios, 6 GHz should be excluded.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
