The fxas21002c_trigger_handler() may fail to acquire sample data because
the runtime PM enters the autosuspend state and sensor can not return
sample data in standby mode..
Resume the sensor before reading the sample data into the buffer within the
trigger handler. After the data is read, place the sensor back into the
autosuspend state.
Fixes: a0701b6263 ("iio: gyro: add core driver for fxas21002c")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241116152945.4006374-1-Frank.Li@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When during a measurement two channels are enabled, two measurements are
done that are reported sequencially in the DATA register. As the code
triggered by reading one of the sysfs properties expects that only one
channel is enabled it only reads the first data set which might or might
not belong to the intended channel.
To prevent this situation disable all channels during probe. This fixes
a problem in practise because the reset default for channel 0 is
enabled. So all measurements before the first measurement on channel 0
(which disables channel 0 at the end) might report wrong values.
Fixes: 7b8d045e49 ("iio: adc: ad7124: allow more than 8 channels")
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20241104101905.845737-2-u.kleine-koenig@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
User Perspective:
When a user sets the phase value, the ad9832_write_phase() is called.
The phase register has a 12-bit resolution, so the valid range is 0 to
4095. If the phase offset value of 4096 is input, it effectively exactly
equals 0 in the lower 12 bits, meaning no offset.
Reasons for the Change:
1) Original Condition (phase > BIT(AD9832_PHASE_BITS)):
This condition allows a phase value equal to 2^12, which is 4096.
However, this value exceeds the valid 12-bit range, as the maximum valid
phase value should be 4095.
2) Modified Condition (phase >= BIT(AD9832_PHASE_BITS)):
Ensures that the phase value is within the valid range, preventing
invalid datafrom being written.
Impact on Subsequent Logic: st->data = cpu_to_be16(addr | phase):
If the phase value is 2^12, i.e., 4096 (0001 0000 0000 0000), and addr
is AD9832_REG_PHASE0 (1100 0000 0000 0000), then addr | phase results in
1101 0000 0000 0000, occupying DB12. According to the section of WRITING
TO A PHASE REGISTER in the datasheet, the MSB 12 PHASE0 bits should be
DB11. The original condition leads to incorrect DB12 usage, which
contradicts the datasheet and could pose potential issues for future
updates if DB12 is used in such related cases.
Fixes: ea707584ba ("Staging: IIO: DDS: AD9832 / AD9835 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Link: https://patch.msgid.link/20241107011015.2472600-3-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
User Perspective:
When a user sets the phase value, the ad9834_write_phase() is called.
The phase register has a 12-bit resolution, so the valid range is 0 to
4095. If the phase offset value of 4096 is input, it effectively exactly
equals 0 in the lower 12 bits, meaning no offset.
Reasons for the Change:
1) Original Condition (phase > BIT(AD9834_PHASE_BITS)):
This condition allows a phase value equal to 2^12, which is 4096.
However, this value exceeds the valid 12-bit range, as the maximum valid
phase value should be 4095.
2) Modified Condition (phase >= BIT(AD9834_PHASE_BITS)):
Ensures that the phase value is within the valid range, preventing
invalid datafrom being written.
Impact on Subsequent Logic: st->data = cpu_to_be16(addr | phase):
If the phase value is 2^12, i.e., 4096 (0001 0000 0000 0000), and addr
is AD9834_REG_PHASE0 (1100 0000 0000 0000), then addr | phase results in
1101 0000 0000 0000, occupying DB12. According to the section of WRITING
TO A PHASE REGISTER in the datasheet, the MSB 12 PHASE0 bits should be
DB11. The original condition leads to incorrect DB12 usage, which
contradicts the datasheet and could pose potential issues for future
updates if DB12 is used in such related cases.
Fixes: 12b9d5bf76 ("Staging: IIO: DDS: AD9833 / AD9834 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20241107011015.2472600-2-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fxls8967af is similar with fxls8962af, the only difference is the device id
change to 0x87.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241115-fxls-v2-4-95f3df9228ed@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fxls8974cf is similar with fxls8962af, the only difference is the device id
change to 0x86.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241115-fxls-v2-3-95f3df9228ed@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add 'nxp,fxls8974cf' compatible for the FXLS8974CF sensor, falling back to
'nxp,fxls8962af' as the only difference is the ID.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241115-fxls-v2-2-95f3df9228ed@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add 'nxp,fxls8967af' compatible for the FXLS8967AF sensor, falling back to
'nxp,fxls8962af' as the only difference is the ID.
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241115-fxls-v2-1-95f3df9228ed@nxp.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20241104190846.278417-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I3C client drivers should not include linux/i3c/master.h. Use
i3cdev_to_dev() to get the device pointer from struct i3c_device
to be able to avoid that include.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20241109145430.3702482-1-linux@roeck-us.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the adis16486, adis16487 and adis16489 Six Degrees
of Freedom Inertial Sensors to the list of compatible devices
of the adis16480 iio subsystem driver.
adis16486 is similar to adis16485, has the exact same channels
but acceleration and delta velocity scales are different.
adis16487 is fallback compatible with adis16485 and as a
consequence, dt-bindings list was updated to use oneOf.
adis16489 is similar to adis16488 but lacks the magnetometer
and has a different accelerometer scale.
Signed-off-by: Darius Berghe <darius.berghe@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20241108125814.3097213-4-darius.berghe@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add datasheet links for adis16486, adis16487 and adis16489
Six Degrees of Freedom Inertial Sensors into the existing
adis16480 driver documentation.
adis16486 is similar to adis16485, has the exact same channels
but acceleration and delta velocity scales are different.
adis16487 is fallback compatible with adis16485.
adis16489 is similar to adis16488 but lacks the magnetometer
and has a different accelerometer scale.
Signed-off-by: Darius Berghe <darius.berghe@analog.com>
Link: https://patch.msgid.link/20241108125814.3097213-3-darius.berghe@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for adis16486, adis16487 and adis16489 Six Degrees
of Freedom Inertial Sensors into the existing adis16480 iio
subsystem driver.
adis16486 is similar to adis16485, has the exact same channels
but acceleration and delta velocity scales are different.
adis16487 is fallback compatible with adis16485.
adis16489 is similar to adis16488 but lacks the magnetometer
and has a different accelerometer scale.
Signed-off-by: Darius Berghe <darius.berghe@analog.com>
Link: https://patch.msgid.link/20241108125814.3097213-2-darius.berghe@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Recently new functions for IO memcpy and IO memset were added in
libs/iomem_copy.c. So, remove the arch specific implementations, to fall
back to the generic ones which do exactly the same. Keep memcpy_fromio
for now, because it's slight more optimized by doing 'u16' accesses if
the buffer is aligned this way.
Signed-off-by: Julian Vetter <julian@outer-limits.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>
The size parameter of functions memremap_is_efi_data(),
memremap_is_setup_data() and early_memremap_is_setup_data() is not used.
Remove it.
[ bp: Massage commit message. ]
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20241123114221.149383-4-bhe@redhat.com
memremap_is_setup_data() and early_memremap_is_setup_data() share
completely the same process and handling, except for the differing
memremap/unmap invocations.
Add a helper __memremap_is_setup_data() extracting the common part and
simplify a lot of code while at it.
Mark __memremap_is_setup_data() as __ref to suppress this section
mismatch warning:
WARNING: modpost: vmlinux: section mismatch in reference: __memremap_is_setup_data+0x5f (section: .text) ->
early_memunmap (section: .init.text)
[ bp: Massage a bit. ]
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20241123114221.149383-2-bhe@redhat.com
Linus noticed that the new if_not_guard() definition is fragile:
"This macro generates actively wrong code if it happens to be inside an
if-statement or a loop without a block.
IOW, code like this:
for (iterate-over-something)
if_not_guard(a)
return -BUSY;
looks like will build fine, but will generate completely incorrect code."
The reason is that the __if_not_guard() macro is multi-statement, so
while most kernel developers expect macros to be simple or at least
compound statements - but for __if_not_guard() it is not so:
#define __if_not_guard(_name, _id, args...) \
BUILD_BUG_ON(!__is_cond_ptr(_name)); \
CLASS(_name, _id)(args); \
if (!__guard_ptr(_name)(&_id))
To add insult to injury, the placement of the BUILD_BUG_ON() line makes
the macro appear to compile fine, but it will generate incorrect code
as Linus reported, for example if used within iteration or conditional
statements that will use the first statement of a macro as a loop body
or conditional statement body.
[ I'd also like to note that the original submission by David Lechner did
not contain the BUILD_BUG_ON() line, so it was safer than what we ended
up committing. Mea culpa. ]
It doesn't appear to be possible to turn this macro into a robust
single or compound statement that could be used in single statements,
due to the necessity to define an auto scope variable with an open
scope and the necessity of it having to expand to a partial 'if'
statement with no body.
Instead of trying to work around this fragility, just remove the
construct before it gets used.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Lechner <dlechner@baylibre.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/Z1LBnX9TpZLR5Dkf@gmail.com
Guillaume Nault says:
====================
net: Convert some UDP tunnel drivers to NETDEV_PCPU_STAT_DSTATS.
VXLAN, Geneve and Bareudp use various device counters for managing
RX and TX statistics:
* VXLAN uses the device core_stats for RX and TX drops, tstats for
regular RX/TX counters and DEV_STATS_INC() for various types of
RX/TX errors.
* Geneve uses tstats for regular RX/TX counters and DEV_STATS_INC()
for everything else, include RX/TX drops.
* Bareudp, was recently converted to follow VXLAN behaviour, that is,
device core_stats for RX and TX drops, tstats for regular RX/TX
counters and DEV_STATS_INC() for other counter types.
Let's consolidate statistics management around the dstats counters
instead. This avoids using core_stats in VXLAN and Bareudp, as
core_stats is supposed to be used by core networking code only (and not
in drivers). This also allows Geneve to avoid using atomic increments
when updating RX and TX drop counters, as dstats is per-cpu. Finally,
this also simplifies the code as all three modules now handle stats in
the same way and with only two different sets of counters (the per-cpu
dstats and the atomic DEV_STATS_INC()).
Patch 1 creates dstats helper functions that can be used outside of VRF
(until then, dstats was VRF-specific).
Then patches 2 to 4, convert VXLAN, Geneve and Bareudp, one by one.
====================
Link: https://patch.msgid.link/cover.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bareudp uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX
packet counters. It was also recently converted to use the device core
stats (dev_core_stats_*()) for RX and TX drops (see commit 788d5d655b
("bareudp: Use pcpu stats to update rx_dropped counter.")).
Since core stats are to be avoided in drivers, and for consistency with
VXLAN and Geneve, let's convert packet stats handling to DSTATS, which
can handle RX/TX stats and packet drops. Statistics that don't fit
DSTATS are still updated atomically with DEV_STATS_INC().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/0f4f8448db3ff449ac6e939872b28cf3f8982da7.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geneve uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX
packet counters. All other counters are handled using atomic increments
with DEV_STATS_INC().
Let's convert packet stats handling to DSTATS, which has a per-cpu
counter for packet drops too, to avoid the cost of atomic increments
in these cases. Statistics that don't fit DSTATS are still updated
atomically with DEV_STATS_INC().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/7af5c09f3c26f0f231fbe383822ca5d1ce0278fa.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VXLAN uses the TSTATS infrastructure (dev_sw_netstats_*()) for RX and
TX packet counters. It also uses the device core stats
(dev_core_stats_*()) for RX and TX drops.
Let's consolidate that using the DSTATS infrastructure, which can
handle both packet counters and packet drops. Statistics that don't
fit DSTATS are still updated atomically with DEV_STATS_INC().
While there, convert the "len" variable of vxlan_encap_bypass() to
unsigned int, to respect the types of skb->len and
dev_dstats_[rt]x_add().
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/145558b184b3cda77911ca5682b6eb83c3ffed8e.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently vrf is the only module that uses NETDEV_PCPU_STAT_DSTATS.
In order to make this kind of statistics available to other modules,
we need to define the update functions in netdevice.h.
Therefore, let's define dev_dstats_*() functions for RX and TX packet
updates (packets, bytes and drops). Use these new functions in vrf.c
instead of vrf_rx_stats() and the other manual counter updates.
While there, update the type of the "len" variables to "unsigned int",
so that there're aligned with both skb->len and the new dstats update
functions.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://patch.msgid.link/d7a552ee382c79f4854e7fcc224cf176cd21150d.1733313925.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel says:
====================
lan78xx: Preparations for PHYlink
This patch set is part of the preparatory work for migrating the lan78xx
USB Ethernet driver to the PHYlink framework. During extensive testing,
I observed that resetting the USB adapter can lead to various read/write
errors. While the errors themselves are acceptable, they generate
excessive log messages, resulting in significant log spam. This set
improves error handling to reduce logging noise by addressing errors
directly and returning early when necessary.
Key highlights of this series include:
- Enhanced error handling to reduce log spam while preserving the
original error values, avoiding unnecessary overwrites.
- Improved error reporting using the `%pe` specifier for better clarity
in log messages.
- Removal of redundant and problematic PHY fixups for LAN8835 and
KSZ9031, with detailed explanations in the respective patches.
- Cleanup of code structure, including unified `goto` labels for better
readability and maintainability, even in simple editors.
====================
Link: https://patch.msgid.link/20241204084142.1152696-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update `lan78xx_dataport_write` and `lan78xx_deferred_multicast_write`
to:
- Handle errors during register read/write operations.
- Exit immediately on errors and log them using `%pe` for clarity.
- Avoid silent failures by propagating error codes properly.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-11-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update `lan78xx_irq_bus_sync_unlock` to handle errors in register
read/write operations. If an error occurs, log it and exit the function
appropriately. This ensures proper handling of failures during IRQ
synchronization.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-10-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve error handling in `lan78xx_set_rx_max_frame_length` by:
- Checking return values from register read/write operations and
propagating errors.
- Exiting immediately on failure to ensure proper error reporting.
In `lan78xx_change_mtu`, log errors when changing MTU fails, using `%pe`
for clear error representation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-9-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert `lan78xx_init_ltm` to return error codes and handle errors
properly. Previously, errors during the LTM initialization process were
not propagated, potentially leading to undetected issues. This patch
ensures:
- Errors in `lan78xx_read_reg` and `lan78xx_write_reg` are checked and
handled.
- Errors are logged with detailed messages using `%pe` for clarity.
- The function exits immediately on error, returning the error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-8-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refine error handling in EEPROM and OTP read/write functions by:
- Return error values immediately upon detection.
- Avoid overwriting correct error codes with `-EIO`.
- Preserve initial error codes as they were appropriate for specific
failures.
- Use `-ETIMEDOUT` for timeout conditions instead of `-EIO`.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensure proper error handling in `lan78xx_mdiobus_read` and
`lan78xx_mdiobus_write` by checking return values of register read/write
operations and returning errors to the caller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace integer error codes with the `%pe` format specifier in register
read and write error messages. This change provides human-readable error
strings, making logs more informative and debugging easier.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move following functions to avoid forward declarations in the code:
- lan78xx_start_hw()
- lan78xx_stop_hw()
- lan78xx_flush_fifo()
- lan78xx_start_tx_path()
- lan78xx_stop_tx_path()
- lan78xx_flush_tx_fifo()
- lan78xx_start_rx_path()
- lan78xx_stop_rx_path()
- lan78xx_flush_rx_fifo()
These functions will be used in an upcoming PHYlink migration patch.
No modifications to the functionality of the code are made.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the KSZ9031RNX PHY fixup from the lan78xx driver. The fixup applied
specific RGMII pad skew configurations globally, but these settings violate the
RGMII specification and cause more harm than benefit.
Key issues with the fixup:
1. **Non-Compliant Timing**: The fixup's delay settings fall outside the RGMII
specification requirements of 1.5 ns to 2.0 ns:
- RX Path: Total delay of **2.16 ns** (PHY internal delay of 1.2 ns + 0.96
ns skew).
- TX Path: Total delay of **0.96 ns**, significantly below the RGMII minimum
of 1.5 ns.
2. **Redundant or Incorrect Configurations**:
- The RGMII skew registers written by the fixup do not meaningfully alter
the PHY's default behavior and fail to account for its internal delays.
- The TX_DATA pad skew was not configured, relying on power-on defaults
that are insufficient for RGMII compliance.
3. **Micrel Driver Support**: By setting `PHY_INTERFACE_MODE_RGMII_ID`, the
Micrel driver can calculate and assign appropriate skew values for the
KSZ9031 PHY. This ensures better timing configurations without relying on
external fixups.
4. **System Interference**: The fixup applied globally, reconfiguring all
KSZ9031 PHYs in the system, even those unrelated to the LAN78xx adapter.
This could lead to unintended and harmful behavior on unrelated interfaces.
While the fixup is removed, a better mechanism is still needed to dynamically
determine the optimal combination of PHY and MAC delays to fully meet RGMII
requirements without relying on Device Tree or global fixups. This would allow
for robust operation across different hardware configurations.
The Micrel driver is capable of using the interface mode value to calculate and
apply better skew values, providing a configuration much closer to the RGMII
specification than the fixup. Removing the fixup ensures better default
behavior and prevents harm to other system interfaces.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the PHY fixup for the LAN8835 PHY in the lan78xx driver due to
the following reasons:
- There is no publicly available information about the LAN8835 PHY.
However, it appears to be the integrated PHY used in the LAN7800 and
LAN7850 USB Ethernet controllers. These PHYs use the GMII interface,
not RGMII as configured by the fixup.
- The correct driver for handling the LAN8835 PHY functionality is the
Microchip PHY driver (`drivers/net/phy/microchip.c`), which properly
supports these integrated PHYs.
- The PHY ID `0x0007C130` is actually used by the LAN8742A PHY, which
only supports RMII. This interface is incompatible with the LAN78xx
MAC, as the LAN7801 (the only LAN78xx version without an integrated
PHY) supports only RGMII.
- The mask applied for this fixup is overly broad, inadvertently
covering both Microchip LAN88xx PHYs and unrelated SMSC LAN8742A PHYs,
leading to potential conflicts with other devices.
- Testing has shown that removing this fixup for LAN7800 and LAN7850
does not result in any noticeable difference in functionality, as the
Microchip PHY driver (`drivers/net/phy/microchip.c`) handles all
necessary configurations for these integrated PHYs.
- Registering this fixup globally (not limited to USB devices) risks
conflicts by unintentionally modifying other interfaces whenever a
LAN7801 adapter is connected to the system.
Note that both LAN7800 and LAN7850 USB Ethernet controllers use an
integrated PHY with the ID `0x0007C132`. Additionally, the LAN7515, a
specialized part for Raspberry Pi, includes an integrated LAN7800 USB
Ethernet controller and USB hub in a multifunctional chip design, and it
also uses the same PHY ID (`0x0007C132`).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241204084142.1152696-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: phylib EEE cleanups
Clean up phylib's EEE support. Patches previously posted as RFC as part
of the phylink EEE series.
Patch 1 changes the Marvell driver to use the state we store in
struct phy_device, rather than manually calling
phydev->eee_cfg.eee_enabled.
Patch 2 avoids genphy_c45_ethtool_get_eee() setting ->eee_enabled, as
we copy that from phydev->eee_cfg.eee_enabled later, and after patch 3
mo one uses this after calling genphy_c45_ethtool_get_eee(). In fact,
the only caller of this function now is phy_ethtool_get_eee().
As all callers to genphy_c45_eee_is_active() now pass NULL as its
is_enabled flag, this is no longer useful. Remove the argument in
patch 3.
Patch 4 updates the phylib documentation to make it absolutely clear
that phy_ethtool_get_eee() now fills in all members of struct
ethtool_keee, which is why we now have so many buggy network drivers.
====================
Link: https://patch.msgid.link/Z1GDZlFyF2fsFa3S@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the phy_ethtool_get_eee() documentation to make it clear that
all members of struct ethtool_keee are written by this function.
keee.supported, keee.advertised, keee.lp_advertised and keee.eee_active
are all written by genphy_c45_ethtool_get_eee().
keee.tx_lpi_timer, keee.tx_lpi_enabled and keee.eee_enabled are all
written by eeecfg_to_eee().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1tJ9JH-006LIz-SO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All callers to genphy_c45_eee_is_active() now pass NULL as the
is_enabled argument, which means we never use the value computed
in this function. Remove the argument and clean up this function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9JC-006LIt-Ne@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
genphy_c45_ethtool_get_eee() is only called from phy_ethtool_get_eee(),
which then calls eeecfg_to_eee(). eeecfg_to_eee() will overwrite
keee.eee_enabled, so there's no point setting keee.eee_enabled in
genphy_c45_ethtool_get_eee(). Remove this assignment.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9J7-006LIn-Jr@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rather than calling genphy_c45_ethtool_get_eee() to retrieve whether
EEE is enabled, use the value stored in the phy_device eee_cfg
structure.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tJ9J2-006LIh-Fl@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix various integer type conversions by using strtoull and a temporary
variable which is bounds checked before being casted into the
appropriate cfg_* variable for use by the test program.
While here:
- free the strdup'd cfg string for overall hygenie.
- initialize napi_id = 0 in setup_queue to avoid warnings on some
compilers.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20241204163239.294123-1-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tipc_exit_net() is very slow and is abused by syzbot.
tipc_nametbl_stop() is called for each netns being dismantled.
Calling synchronize_net() right before freeing tn->nametbl
is a big hammer.
Replace this with kfree_rcu().
Note that RCU is not properly used here, otherwise
tn->nametbl should be cleared before the synchronize_net()
or kfree_rcu(), or even before the cleanup loop.
We might need to fix this at some point.
Also note tipc uses other synchronize_rcu() calls,
more work is needed to make tipc_exit_net() much faster.
List of remaining calls to synchronize_rcu()
tipc_detach_loopback() (dev_remove_pack())
tipc_bcast_stop()
tipc_sk_rht_destroy()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241204210234.319484-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Chan says:
====================
bnxt_en: Bug fixes
There are 2 bug fixes in this series. This first one fixes the issue
of setting the gso_type incorrectly for HW GRO packets on 5750X (Thor)
chips. This can cause HW GRO packets to be dropped by the stack if
they are re-segmented. The second one fixes a potential division by
zero crash when dumping FW log coredump.
====================
Link: https://patch.msgid.link/20241204215918.1692597-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
