The commit 587b4ee24f ("arm64: dts: rockchip: add core dtsi file for
RK3399Pro SoCs") describes the RK3399Pro's PCI Express interface as the way
built-in NPU communicates with the rest of the SoC. All available evidence
shows this not to be accurate, as described in detail below. Moreover, the
rk3399pro.dtsi isn't used anywhere, so let's delete it.
The publicly available schematics of the Radxa Rock Pi N10 carrier board [1]
and the Vamrs VMARC RK3399Pro SoM, [2] which put together form the currently
single supported RK3399Pro-based board, clearly show that the PCI Express x4
interface of this SoC is fully functional and actually not used by the SoC
to communicate with the built-in NPU. In more detail, the VMARC SoM exports
the SoC's PCI Express interface at its board-to-board connector, and the Rock
Pi N10 routes it to an M.2 M-key slot with four PCI Express lanes.
Both the Rockchip RK3399Pro datasheet, version 1.1, [3] and the Rockchip
RK3399Pro technical reference manual (TRM), first part of the version 1.0, [4]
don't describe that the SoC's PCI Express interface is reserved for the NPU.
Instead, the RK3399Pro TRM describes that the NPU uses AHB and AXI interfaces
as the host interface (HIF). The RK3399Pro datasheet clearly describes that
the PCI Express x4 interface is available for general-purpose use, just like
it's the case with the standard Rockchip RK3399 SoC, [5] albeit with a bit
shorter feature list provided in the RK3399Pro datasheet.
Even the publicly available reference RK3399Pro schematic from Rockchip [6]
shows the availability of a standard PCI Express slot with four lanes, which
would be pretty much impossible if the PCI Express interface was reserved
for the communication with the built-in NPU.
Based on the RK3399Pro datasheet [3] and the board schematics, [2][6] the
built-in NPU actually exports NPU_PCIE as a separate PCI Express x2 interface
that's partially pinmuxed with the NPU's separate USB 3.0 interface, which is
described further in the next paragraph. However, the NPU's separate PCI
Express x2 interface is left undocumented in the publicly available RK3399Pro
documentation, in which it's clearly described as reserved for internal use
and not intended for the communication with the NPU. Finally, the evidently
independent nature of the separate NPU_PCIE x2 interface makes ignoring it
safe when it comes to determining the nature and the availability of the
RK3399Pro's main PCI Express x4 interface.
The actual application-level communication with the built-in NPU, including
powering it up and down and uploading the NPU firmware, is performed through
the separate USB 2.0 and USB 3.0 interfaces exported by the NPU, [7] which
the VMARC SoM [2] and the reference board design from Rockchip [6] route to
the SoC's standard USB 2.0 and USB 3.0 interfaces, to make the NPU accessible
to software running on the SoC's ARM cores.
[1] https://dl.radxa.com/rockpin10/docs/hw/rockpi_n10_sch_v1.1_20190909.pdf
[2] https://dl.radxa.com/rockpin10/docs/hw/VMARC_RK3399Pro_sch_V1.1_20190619.pdf
[3] https://www.rockchip.fr/RK3399Pro%20datasheet%20V1.1.pdf
[4] https://www.rockchip.fr/Rockchip%20RK3399Pro%20TRM%20V1.0%20Part1.pdf
[5] https://www.rockchip.fr/RK3399%20datasheet%20V1.8.pdf
[6] https://opensource.rock-chips.com/images/e/e4/RK_EVB_RK3399PRO_LP3S178P332SD8_V11_20181113_RZF.pdf
[7] https://wiki.radxa.com/RockpiN10/dev/NPU-booting
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/4449f7d4eead787308300e2d1d37b88c9d1446b2.1717308862.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'mic-in-differential' DT property supported by the RK809/RK817 audio
codec driver is actually valid if prefixed with 'rockchip,':
DTC_CHK arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dtb
rk3568-evb1-v10.dtb: pmic@20: codec: 'mic-in-differential' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
Make use of the correct property name.
Fixes: 3e4c629ca6 ("arm64: dts: rockchip: enable rk809 audio codec on the rk3568 evb1-v10")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240622-rk809-fixes-v2-5-c0db420d3639@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'mic-in-differential' DT property supported by the RK809/RK817 audio
codec driver is actually valid if prefixed with 'rockchip,':
DTC_CHK arch/arm64/boot/dts/rockchip/rk3566-roc-pc.dtb
rk3566-roc-pc.dtb: pmic@20: codec: 'mic-in-differential' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
Make use of the correct property name.
Fixes: a8e35c4beb ("arm64: dts: rockchip: add audio nodes to rk3566-roc-pc")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240622-rk809-fixes-v2-4-c0db420d3639@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'mic-in-differential' DT property supported by the RK809/RK817 audio
codec driver is actually valid if prefixed with 'rockchip,':
DTC_CHK arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dtb
rk3568-rock-3a.dtb: pmic@20: codec: 'mic-in-differential' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
However, the board doesn't make use of differential signaling, hence
drop the incorrect property and the now unnecessary 'codec' node.
Fixes: 22a442e658 ("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240622-rk809-fixes-v2-3-c0db420d3639@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add rock5b overlays for PCIe endpoint mode support.
If using the rock5b as an endpoint against a normal PC, only the
rk3588-rock-5b-pcie-ep.dtbo needs to be applied.
If using two rock5b:s, with one board as EP and the other board as RC,
rk3588-rock-5b-pcie-ep.dtbo and rk3588-rock-5b-pcie-srns.dtbo has to
be applied to the respective boards.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Link: https://lore.kernel.org/r/20240607-rockchip-pcie-ep-v1-v5-13-0a042d6b0049@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a device tree node representing PCIe endpoint mode.
The controller can either be configured to run in Root Complex or Endpoint
mode.
If a user wants to run the controller in endpoint mode, the user has to
disable the pcie3x4 node and enable the pcie3x4_ep node.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240607-rockchip-pcie-ep-v1-v5-12-0a042d6b0049@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tariq Toukan says:
====================
mlx5 fixes 2024-06-27
This patchset provides fixes from the team to the mlx5 core and EN
drivers.
The first 3 patches by Daniel replace a buggy cap field with a newly
introduced one.
Patch 4 by Chris de-couples ingress ACL creation from a specific flow,
so it's invoked by other flows if needed.
Patch 5 by Jianbo fixes a possible missing cleanup of QoS objects.
Patches 6 and 7 by Leon fixes IPsec stats logic to better reflect the
traffic.
Series generated against:
commit 02ea312055 ("octeontx2-pf: Fix coverity and klockwork issues in octeon PF driver")
V2:
Fixed wrong cited SHA in patch 6.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX devices lack ability to count payload data byte size which is
needed for SA to return to libreswan for rekeying.
As a solution let's approximate that by decreasing headers size from
total size counted by flow steering. The calculation doesn't take into
account any other headers which can be in the packet (e.g. IP extensions).
Fixes: 5a6cddb89b ("net/mlx5e: Update IPsec per SA packets/bytes count")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPsec SA statistics presents successfully decrypted and encrypted
packet and bytes, and not total handled by this SA. So update the
calculation logic to take into account failures.
Fixes: 6fb7f94087 ("net/mlx5e: Connect mlx5 IPsec statistics with XFRM core")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the cited commit, mqprio_rl cleanup and free are mistakenly removed
in mlx5e_priv_cleanup(), and it causes the leakage of host memory and
firmware SCHEDULING_ELEMENT objects while changing eswitch mode. So,
add them back.
Fixes: 0bb7228f70 ("net/mlx5e: Fix mqprio_rl handling on devlink reload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, ingress acl is used for three features. It is created only
when vport metadata match and prio tag are enabled. But active-backup
lag mode also uses it. It is independent of vport metadata match and
prio tag. And vport metadata match can be disabled using the
following devlink command:
# devlink dev param set pci/0000:08:00.0 name esw_port_metadata \
value false cmode runtime
If ingress acl is not created, will hit panic when creating drop rule
for active-backup lag mode. If always create it, there will be about
5% performance degradation.
Fix it by creating ingress acl when needed. If esw_port_metadata is
true, ingress acl exists, then create drop rule using existing
ingress acl. If esw_port_metadata is false, create ingress acl and
then create drop rule.
Fixes: 1749c4c51c ("net/mlx5: E-switch, add drop rule support to ingress ACL")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due a bug in the device max_num_eqs doesn't always reflect a written
value. As a result, setting max_io_eqs may not work but appear
successful. Instead write max_num_eqs_24b, which reflects correct
value.
Fixes: 93197c7c50 ("mlx5/core: Support max_io_eqs for a function")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new capability with more bits is added. If it's set use that value as
the maximum number of EQs available.
This cap is also writable by the vhca_resource_manager to allow limiting
the number of EQs available to SFs and VFs.
Fixes: 93197c7c50 ("mlx5/core: Support max_io_eqs for a function")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose new capability to support changing the number of EQs available
to other functions.
Fixes: 93197c7c50 ("mlx5/core: Support max_io_eqs for a function")
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
selftest: Clean-up and stabilize mirroring tests
The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.
The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy.
mirror_test() accommodated this noisiness by giving the counters an
allowance of several packets. But that only works up to a point, and on
busy systems won't be always enough.
In this patch set, clean up and stabilize the mirroring selftests. The
original intention was to port the tests over to UDP, but the logic of
ICMP ends up being so entangled in the mirroring selftests that the
changes feel overly invasive. Instead, ICMP is kept, but where possible,
we match on ICMP message type, thus filtering out hits by other ICMP
messages.
Where this is not practical (where the counter tap is put on a device
that carries encapsulated packets), switch the counter condition to _at
least_ X observed packets. This is less robust, but barely so --
probably the only scenario that this would not catch is something like
erroneous packet duplication, which would hopefully get caught by the
numerous other tests in this extensive suite.
- Patches #1 to #3 clean up parameters at various helpers.
- Patches #4 to #6 stabilize the mirroring selftests as described above.
- Mirroring tests currently allow testing SW datapath even on HW
netdevices by trapping traffic to the SW datapath. This complicates
the tests a bit without a good reason: to test SW datapath, just run
the selftests on the veth topology. Thus in patch #7, drop support for
this dual SW/HW testing.
- At this point, some cleanups were either made possible by the previous
patches, or were always possible. In patches #8 to #11, realize these
cleanups.
- In patch #12, fix mlxsw mirror_gre selftest to respect setting TESTS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is unusual in that overriding TESTS does not change the tests to
be run. Split the individual tests into several functions and invoke them
through tests_run() as appropriate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing calls these.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are not used anymore.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftest does not use functions from mirror_gre_lib, ditch the import.
It does not use arping either, so drop the require_command as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, the function test_span_failable() is always
called with should_fail=1. Drop the argument and streamline the code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirroring tests are currently run in a skip_hw and optionally a skip_sw
mode. The former tests the SW datapath, the latter the HW datapath, if
available. In order to be able to test SW datapath on HW loopbacks, traps
are installed on ingress to get traffic from the HW datapath to the SW one.
This adds an unnecessary complexity when it would be much simpler to just
use a veth-based topology to test the SW datapath. Thus drop all the code
that supports this dual testing.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.
The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.
mirror_test() accommodated this noisiness by giving the counters an
allowance of several packets. But in the previous patch, where possible,
counter taps were changed to match only on an exact ICMP message. At least
in those cases, we can demand an exact number of packets to match.
Where the tap is installed on a connective netdevice, the exact matching is
not practical (though with u32, anything is possible). In those places,
there should still be some leeway -- and probably bigger than before,
because experience shows that these tests are very noisy.
To that end, change mirror_test() so that it can be either called with an
exact number to expect, or with an expression. Where leeway is needed,
adjust callers to pass a ">= 10" instead of mere 10.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.
The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.
However, often the counter tap is installed at the remote end of the gretap
tunnel. Since this is a SW-datapath scenario anyway, we can make the filter
arbitrarily accurate.
Thus in this patch, add parameters forward_type and backward_type to
several mirroring test helpers, as some other helpers already have. Then
change do_test_span_dir_ips() to instead of installing one generic tap and
using it for test in both directions, install the tap for each direction
separately, matching on the ICMP type given by these parameters.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test works by sending packets through a tunnel, whence they are
forwarded to a LAG. One of the LAG children is removed from the LAG prior
to the exercise, and the test then counts how many packets pass through the
other one. The issue with this is that it counts all packets, not just the
encapsulated ones.
So instead add a second gretap endpoint to receive the sent packets, and
check reception counters there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument $dir has a fallback value of "ingress". Move the fallback from
the usage site to the argument definition block to make the fact clearer.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument is not used by these functions except to propagate it for
ultimately no purpose.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some functions, argument-forwarding through "$@" without listing the
individual arguments explicitly is fundamental to the operation of a
function. E.g. xfail_on_veth() should be able to run various tests in the
fail-to-xfail regime, and usage of "$@" is appropriate as an abstraction
mechanism. For functions such as simple_if_init(), $@ is a handy way to
pass an array.
In other functions, it's merely a mechanism to save some typing, which
however ends up obscuring the real arguments and makes life hard for those
that end up reading the code.
This patch adds some of the implicit function arguments and correspondingly
expands $@'s. In several cases this will come in handy as following patches
adjust the parameter lists.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TBT-alt mode the driver doesn't program the PHY's PLL, which is
handled instead by Thunderbolt driver/FW components, hence the PLL's HW
vs. SW state verification should be skipped. During HW readout set a flag
in the PLL state if the port was at the moment in TBT-alt mode and skip
the verification of PLL parameters in this case.
Fixes: 45fe957ae7 ("drm/i915/display: Add compare config for MTL+ platforms")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11258
Cc: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626170813.806470-1-imre.deak@intel.com
Danielle Ratson says:
====================
Add ability to flash modules' firmware
CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.2.2 of revision
4.0 of the CMIS standard.
According to the CMIS standard, the firmware update process is done
using a CDB commands sequence.
CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.12 of revision 4.0.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid RTNL
being held for too long and to allow several modules to be updated
simultaneously. The interface is designed with CMIS compliant modules in
mind, but kept generic enough to accommodate future use cases, if these
arise.
The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:
* The upper layer that will be triggered from the module layer, is
cmis_ fw_update.
* The lower one is cmis_cdb.
In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the cmis_cdb interface clean and
the cmis_fw_update specific to the cdb commands handling it.
The communication between the kernel and the driver will be done using
two ethtool operations that enable reading and writing the transceiver
module EEPROM.
The operation ethtool_ops::get_module_eeprom_by_page, that is already
implemented, will be used for reading from the EEPROM the CDB reply,
e.g. reading module setting, state, etc.
The operation ethtool_ops::set_module_eeprom_by_page, that is added in
the current patchset, will be used for writing to the EEPROM the CDB
command such as start firmware image, run firmware image, etc.
Therefore in order for a driver to implement module flashing, that
driver needs to implement the two functions mentioned above.
Patchset overview:
Patch #1-#2: Implement the EEPROM writing in mlxsw.
Patch #3: Define the interface between the kernel and user space.
Patch #4: Add ability to notify the flashing firmware progress.
Patch #5: Veto operations during flashing.
Patch #6: Add extended compliance codes.
Patch #7: Add the cdb layer.
Patch #8: Add the fw_update layer.
Patch #9: Add ability to flash transceiver modules' firmware.
v8:
Patch #7:
* In the ethtool_cmis_wait_for_cond() evaluate the condition once more
to decide if the error code should be -ETIMEDOUT or something else.
* s/netdev_err/netdev_err_once.
v7:
Patch #4:
* Return -ENOMEM instead of PTR_ERR(attr) on
ethnl_module_fw_flash_ntf_put_err().
Patch #9:
* Fix Warning for not unlocking the spin_lock in the error flow
on module_flash_fw_work_list_add().
* Avoid the fall-through on ethnl_sock_priv_destroy().
v6:
* Squash some of the last patch to patch #5 and patch #9.
Patch #3:
* Add paragraph in .rst file.
Patch #4:
* Reserve '1' more place on SKB for NUL terminator in
the error message string.
* Add more prints on error flow, re-write the printing
function and add ethnl_module_fw_flash_ntf_put_err().
* Change the communication method so notification will be
sent in unicast instead of multicast.
* Add new 'struct ethnl_module_fw_flash_ntf_params' that holds
the relevant info for unicast communication and use it to
send notification to the specific socket.
* s/nla_put_u64_64bit/nla_put_uint/
Patch #7:
* In ethtool_cmis_cdb_init(), Use 'const' for the 'params'
parameter.
Patch #8:
* Add a list field to struct ethtool_module_fw_flash for
module_fw_flash_work_list that will be presented in the next
patch.
* Move ethtool_cmis_fw_update() cleaning to a new function that
will be represented in the next patch.
* Move some of the fields in struct ethtool_module_fw_flash to
a separate struct, so ethtool_cmis_fw_update() will get only
the relevant parameters for it.
* Edit the relevant functions to get the relevant params for
them.
* s/CMIS_MODULE_READY_MAX_DURATION_USEC/CMIS_MODULE_READY_MAX_DURATION_MSEC
Patch #9:
* Add a paragraph in the commit message.
* Rename labels in module_flash_fw_schedule().
* Add info to genl_sk_priv_*() and implement the relevant
callbacks, in order to handle properly a scenario of closing
the socket from user space before the work item was ended.
* Add a list the holds all the ethtool_module_fw_flash struct
that corresponds to the in progress work items.
* Add a new enum for the socket types.
* Use both above to identify a flashing socket, add it to the
list and when closing socket affect only the flashing type.
* Create a new function that will get the work item instead of
ethtool_cmis_fw_update().
* Edit the relevant functions to get the relevant params for
them.
* The new function will call the old ethtool_cmis_fw_update(),
and do the cleaning, so the existence of the list should be
completely isolated in module.c.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to flash the modules' firmware by implementing the
interface between the user space and the kernel.
Example from a succeeding implementation:
# ethtool --flash-module-firmware swp40 file test.bin
Transceiver module firmware flashing started for device swp40
Transceiver module firmware flashing in progress for device swp40
Progress: 99%
Transceiver module firmware flashing completed for device swp40
In addition, add infrastructure that allows modules to set socket-specific
private data. This ensures that when a socket is closed from user space
during the flashing process, the right socket halts sending notifications
to user space until the work item is completed.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the CMIS standard, the firmware update process is done using
a CDB commands sequence.
Implement a work that will be triggered from the module layer in the
next patch the will initiate and execute all the CDB commands in order, to
eventually complete the firmware update process.
This flashing process includes, writing the firmware image, running the new
firmware image and committing it after testing, so that it will run upon
reset.
This work will also notify user space about the progress of the firmware
update process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.20 of revision 5.2.
Page 9Fh is used to specify the CDB command to be executed and also
provides an area for a local payload (LPL).
According to the CMIS standard, the firmware update process is done using
a CDB commands sequence that will be implemented in the next patch.
The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:
* The upper layer that will be triggered from the module layer, is
cmis_fw_update.
* The lower one is cmis_cdb.
In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the CDB interface clean and the
cmis_fw_update specific to the CDB commands handling it.
These two layers will communicate using the API the consists of three
functions:
- struct ethtool_cmis_cdb *
ethtool_cmis_cdb_init(struct net_device *dev,
struct ethtool_module_fw_flash_params *params);
- void ethtool_cmis_cdb_fini(struct ethtool_cmis_cdb *cdb);
- int ethtool_cmis_cdb_execute_cmd(struct net_device *dev,
struct ethtool_cmis_cdb_cmd_args *args);
Add the CDB layer to support initializing, finishing and executing CDB
commands:
* The initialization process will include creating of an ethtool_cmis_cdb
instance, querying the module CDB support, entering and validating the
password from user space (CMD 0x0000) and querying the module features
(CMD 0x0040).
* The finishing API will simply free the ethtool_cmis_cdb instance.
* The executing process will write the CDB command to EEPROM using
set_module_eeprom_by_page() that was presented earlier, and will
process the reply from EEPROM.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications.
Add SFF-8024 extended compliance code definitions for CMIS compliant
modules and use them in the next patch to determine the firmware flashing
work.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operations cannot be performed during the firmware flashing
process.
For example:
- Port must be down during the whole flashing process to avoid packet loss
while committing reset for example.
- Writing to EEPROM interrupts the flashing process, so operations like
ethtool dump, module reset, get and set power mode should be vetoed.
- Split port firmware flashing should be vetoed.
In order to veto those scenarios, add a flag in 'struct net_device' that
indicates when a firmware flash is taking place on the module and use it
to prevent interruptions during the process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add progress notifications ability to user space while flashing modules'
firmware by implementing the interface between the user space and the
kernel.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.3.1 of revision 5.2 of
the CMIS standard.
Add a pair of new ethtool messages that allow:
* User space to trigger firmware update of transceiver modules
* The kernel to notify user space about the progress of the process
The user interface is designed to be asynchronous in order to avoid
RTNL being held for too long and to allow several modules to be
updated simultaneously. The interface is designed with CMIS compliant
modules in mind, but kept generic enough to accommodate future use
cases, if these arise.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ethtool_ops::set_module_eeprom_by_page operation to allow
ethtool to write to a transceiver module EEPROM, in a similar fashion to
the ethtool_ops::get_module_eeprom_by_page operation.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool can already retrieve information from a transceiver module
EEPROM by invoking the ethtool_ops::get_module_eeprom_by_page operation.
Add a corresponding operation that allows ethtool to write to a
transceiver module EEPROM.
The new write operation is purely an in-kernel API and is not exposed to
user space.
The purpose of this operation is not to enable arbitrary read / write
access, but to allow the kernel to write to specific addresses as part
of transceiver module firmware flashing. In the future, more
functionality can be implemented on top of these read / write
operations.
Adjust the comments of the 'ethtool_module_eeprom' structure as it is
no longer used only for read access.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSISRC __________
__\_
| \
pll4_p_ck ->| 1 |____dsi_k
ck_dsi_phy ->| 0 |
|____/
A DSI clock is missing in the clock framework. Looking at the
clk_summary, it appears that 'ck_dsi_phy' is not implemented. Since the
DSI kernel clock is based on the internal DSI pll. The common clock
driver can not directly expose this 'ck_dsi_phy' clock because it does
not contain any common registers with the DSI. Thus it needs to be done
directly within the DSI phy driver.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-4-raphael.gallais-pou@foss.st.com
Update control of clocks and supply thanks to the PM runtime
mechanism to avoid kernel crash during a system suspend.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-3-raphael.gallais-pou@foss.st.com
Use RUNTIME_PM_OPS() instead of the old SET_SYSTEM_SLEEP_PM_OPS().
This means we don't need __maybe_unused on the functions.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240129104106.43141-2-raphael.gallais-pou@foss.st.com
In some production workloads we noticed that connections could
sometimes close extremely prematurely with ETIMEDOUT after
transmitting only 1 TLP and RTO retransmission (when we would normally
expect roughly tcp_retries2 = TCP_RETR2 = 15 RTOs before a connection
closes with ETIMEDOUT).
From tracing we determined that these workloads can suffer from a
scenario where in fast recovery, after some retransmits, a DSACK undo
can happen at a point where the scoreboard is totally clear (we have
retrans_out == sacked_out == lost_out == 0). In such cases, calling
tcp_try_keep_open() means that we do not execute any code path that
clears tp->retrans_stamp to 0. That means that tp->retrans_stamp can
remain erroneously set to the start time of the undone fast recovery,
even after the fast recovery is undone. If minutes or hours elapse,
and then a TLP/RTO/RTO sequence occurs, then the start_ts value in
retransmits_timed_out() (which is from tp->retrans_stamp) will be
erroneously ancient (left over from the fast recovery undone via
DSACKs). Thus this ancient tp->retrans_stamp value can cause the
connection to die very prematurely with ETIMEDOUT via
tcp_write_err().
The fix: we change DSACK undo in fast recovery (TCP_CA_Recovery) to
call tcp_try_to_open() instead of tcp_try_keep_open(). This ensures
that if no retransmits are in flight at the time of DSACK undo in fast
recovery then we properly zero retrans_stamp. Note that calling
tcp_try_to_open() is more consistent with other loss recovery
behavior, since normal fast recovery (CA_Recovery) and RTO recovery
(CA_Loss) both normally end when tp->snd_una meets or exceeds
tp->high_seq and then in tcp_fastretrans_alert() the "default" switch
case executes tcp_try_to_open(). Also note that by inspection this
change to call tcp_try_to_open() implies at least one other nice bug
fix, where now an ECE-marked DSACK that causes an undo will properly
invoke tcp_enter_cwr() rather than ignoring the ECE mark.
Fixes: c7d9d6a185 ("tcp: undo on DSACK during recovery")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Low-Voltage Differential Signaling (LVDS) Display Interface
Transmitter handles the LVDS protocol: it maps the pixels received from
the upstream Pixel-DMA LCD-TFT Display Controller (LTDC) onto the LVDS
PHY.
It is composed of three sub blocks:
* LVDS host: handles the LVDS protocol (FPD / OpenLDI) and maps
its input pixels onto the data lanes of the PHY
* LVDS PHY: parallelize the data and drives the LVDS data lanes
* LVDS wrapper: handles top-level settings
The LVDS controller driver supports the following high-level features:
* FDP-Link-I and OpenLDI (v0.95) protocols
* Single-Link or Dual-Link operation
* Single-Display or Double-Display (with the same content
duplicated on both)
* Flexible Bit-Mapping, including JEIDA and VESA
* RGB888 or RGB666 output
* Synchronous design, with one input pixel per clock cycle
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@foss.st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226-lvds-v6-2-15e3463fbe70@foss.st.com
For users that hold a reference to a pidfd procfs might not even be
available nor is it desirable to parse through procfs just for the sake
of getting namespace file descriptors for a process.
Make it possible to directly retrieve namespace file descriptors from a
pidfd. Pidfds already can be used with setns() to change a set of
namespaces atomically.
Link: https://lore.kernel.org/r/20240627-work-pidfs-v1-4-7e9ab6cc3bb1@kernel.org
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
and call it from open_related_ns().
Link: https://lore.kernel.org/r/20240627-work-pidfs-v1-3-7e9ab6cc3bb1@kernel.org
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
They all contains struct ns_common ns and if there ever is one where
that isn't the case we'll catch it here at build time.
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add a simple cleanup helper for nsproxy.
Link: https://lore.kernel.org/r/20240627-work-pidfs-v1-2-7e9ab6cc3bb1@kernel.org
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add a helper that returns the file descriptor and ensures that the old
variable contains a negative value. This makes it easy to rely on
CLASS(get_unused_fd).
Link: https://lore.kernel.org/r/20240627-work-pidfs-v1-1-7e9ab6cc3bb1@kernel.org
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
