In WoWLAN net-detect mode, the firmware periodically performs scans
and sends scan reports via C2H, which driver does not need. These
unnecessary C2H events cause firmware watchdog timeout, leading
to unexpected wakeups and SER 0x2599 on 8922AE.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250811123744.15361-4-pkshih@realtek.com
In ideal scenario, AP's beacon should transmit at the Target Beacon
Transmission Time (TBTT). However, in practice, beacon may be slightly
off-schedule. This beacon "drift" prevents the firmware from receiving
beacon at the expected TBTT, leading to connection disruptions.
To address this, we introduce beacon tracking mechanism to enhance overall
connection stability. This mechanism executes the following steps in each
cycle (2 seconds): 1) Based on the last 32 received beacons, compute the
minimum TBTT offset to use for the next cycle 2) Using the same 32 beacons,
calculate the drift of each. A histogram is plotted, and outliers are
identified using a boxplot. 3) According to the statistical results from
the second step, a maximum receive window size (beacon timeout) is selected
to cover approximately 80% of the beacons and applied to the next cycle.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250811123744.15361-2-pkshih@realtek.com
Ethtool has advanced with additional configurable options, but the
current driver does not support tx-usecs configuration using Ethtool.
Add support to configure and retrieve 'tx-usecs' using ethtool, which
specifies the wait time before servicing an interrupt for Tx coalescing.
Signed-off-by: Vishal Badole <Vishal.Badole@amd.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://patch.msgid.link/20250816141941.126054-1-Vishal.Badole@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove array_size() calls and replace vmalloc() with vmalloc_array() in
bsd_alloc().
vmalloc_array() is also optimized better, resulting in less instructions
being used.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://patch.msgid.link/20250816090659.117699-4-rongqianfeng@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove array_size() calls and replace vmalloc() with vmalloc_array() in
nfp_flower_metadata_init(). vmalloc_array() is also optimized better,
resulting in less instructions being used.
Place 'NFP_FL_STATS_ELEM_RS' with the sizeof() parameter as the second
argument to vmalloc_array() to avoid -Wcalloc-transposed-args compilation
warnings.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://patch.msgid.link/20250816090659.117699-3-rongqianfeng@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove array_size() calls and replace vmalloc() with vmalloc_array() to
simplify the code and maintain consistency with existing kmalloc_array()
usage.
vmalloc_array() is also optimized better, resulting in less instructions
being used.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Link: https://patch.msgid.link/20250816090659.117699-2-rongqianfeng@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc fixes for v6.17-rc
Here are various fixes:
- Patch 1: Better handling SKB extension allocation failures.
A fix for v5.7.
- Patches 2, 3: Avoid resetting MPTCP limits when flushing MPTCP
endpoints. With a validation in the selftests. Fixes for v5.7.
- Patches 4, 5, 6: Disallow '0' as ADD_ADDR retransmission timeout.
With a preparation patch, and a validation in the selftests.
Fixes for v5.11.
- Patches 8, 9: Fix C23 extension warnings in the selftests,
spotted by GCC. Fixes for v6.16.
====================
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-0-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC was complaining about the new label:
mptcp_inq.c:79:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
79 | int err = getaddrinfo(node, service, hints, res);
| ^
mptcp_sockopt.c:166:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
166 | int err = getaddrinfo(node, service, hints, res);
| ^
Simply declare 'err' before the label to avoid this warning.
Fixes: dd367e81b7 ("selftests: mptcp: sockopt: use IPPROTO_MPTCP for getaddrinfo")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-8-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
GCC was complaining about the new label:
mptcp_connect.c:187:2: warning: label followed by a declaration is a C23 extension [-Wc23-extensions]
187 | int err = getaddrinfo(node, service, hints, res);
| ^
Simply declare 'err' before the label to avoid this warning.
Fixes: a862771d1a ("selftests: mptcp: use IPPROTO_MPTCP for getaddrinfo")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-7-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To prevent test instability in the "delete re-add signal" test caused by
ADD_ADDR retransmissions, disable retransmissions for this test by setting
net.mptcp.add_addr_timeout to 0.
Suggested-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-6-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When add_addr_timeout was set to 0, this caused the ADD_ADDR to be
retransmitted immediately, which looks like a buggy behaviour. Instead,
interpret 0 as "no retransmissions needed".
The documentation is updated to explicitly state that setting the timeout
to 0 disables retransmission.
Fixes: 93f323b9cc ("mptcp: add a new sysctl add_addr_timeout")
Cc: stable@vger.kernel.org
Suggested-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-5-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk_reset_timer() was called twice in mptcp_pm_alloc_anno_list.
Simplify the code by using a 'goto' statement to eliminate the
duplication.
Note that this is not a fix, but it will help backporting the following
patch. The same "Fixes" tag has been added for this reason.
Fixes: 93f323b9cc ("mptcp: add a new sysctl add_addr_timeout")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-4-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This modification is linked to the parent commit where the received
ADD_ADDR limit was accidentally reset when the endpoints were flushed.
To validate that, the test is now flushing endpoints after having set
new limits, and before checking them.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-3-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A flush of the MPTCP endpoints should not affect the MPTCP limits. In
other words, 'ip mptcp endpoint flush' should not change 'ip mptcp
limits'.
But it was the case: the MPTCP_PM_ATTR_RCV_ADD_ADDRS (add_addr_accepted)
limit was reset by accident. Removing the reset of this counter during a
flush fixes this issue.
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Cc: stable@vger.kernel.org
Reported-by: Thomas Dreibholz <dreibh@simula.no>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/579
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-2-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When skb_ext_add(skb, SKB_EXT_MPTCP) fails in mptcp_incoming_options(),
we used to return true, letting the segment proceed through the TCP
receive path without a DSS mapping. Such segments can leave inconsistent
mapping state and trigger a mid-stream fallback to TCP, which in testing
collapsed (by artificially forcing failures in skb_ext_add) throughput
to zero.
Return false instead so the TCP input path drops the skb (see
tcp_data_queue() and step-7 processing). This is the safer choice
under memory pressure: it preserves MPTCP correctness and provides
backpressure to the sender.
Control packets remain unaffected: ACK updates and DATA_FIN handling
happen before attempting the extension allocation, and tcp_reset()
continues to ignore the return value.
With this change, MPTCP continues to work at high throughput if we
artificially inject failures into skb_ext_add.
Fixes: 6787b7e350 ("mptcp: avoid processing packet if a subflow reset")
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Paasch <cpaasch@openai.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250815-net-mptcp-misc-fixes-6-17-rc2-v1-1-521fe9957892@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We discourage sending trivial patches to clean up checkpatch warnings.
There are other tools which lead to patches of similarly low value
like some coccicheck warnings. The warnings are useful for new code
but fixing them in the existing code base is a waste of review time.
Broaden the example given in the doc a little bit.
Link: https://patch.msgid.link/20250815165242.124240-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The seg6_genl_sethmac() directly uses the algorithm ID provided by the
userspace without verifying whether it is an HMAC algorithm supported
by the system.
If an unsupported HMAC algorithm ID is configured, packets using SRv6 HMAC
will be dropped during encapsulation or decapsulation.
Fixes: 4f4853dc1c ("ipv6: sr: implement API to control SR HMAC structure")
Signed-off-by: Minhong He <heminhong@kylinos.cn>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20250815063845.85426-1-heminhong@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that a SHA-1 library API is available, use it instead of
crypto_shash. This is simpler and faster.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Link: https://patch.msgid.link/20250815020705.23055-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This place is fetching the stats, u64_stats_update_begin()/end()
should not be used, and the fetcher of stats is in the same
context as the updater of the stats, so don't need any protection
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Link: https://patch.msgid.link/20250815015619.2713-1-lirongqing@baidu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that a SHA-1 library API is available, use it instead of
crypto_shash. This is simpler and faster.
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250815022329.28672-1-ebiggers@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Walleij says:
====================
net: dsa: Move ks8995 "phy" driver to DSA
After we concluded that the KS8995 is a DSA switch, see
commit a0f29a07b6
it is time to move the driver to it's right place under
DSA.
Developing full support for the custom tagging, but we
can make sure the driver does the job it did as a "phy",
act as a switch with individually represented ports.
This patch series achieves that first step so the
current device tree bindings produces working set-ups
and paves the way for custom tagging.
====================
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-0-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We start to extend the KS8995 driver by simply registering it
as a DSA device and implementing a few switch callbacks for
STP set-up and such to begin with.
No special tags or other advanced stuff: we use DSA_TAG_NONE
and rely on the default set-up in the switch with the special
DSA tags turned off. This makes the switch wire up properly
to all its PHY's and simple bridge traffic works properly.
After this the bridge DT bindings are respected, ports and their
PHYs get connected to the switch and react appropriately through
the phylib when cables are plugged in etc.
Tested like this in a hacky OpenWrt image:
Bring up conduit interface manually:
ixp4xx_eth c8009000.ethernet eth0: eth0: link up,
speed 100 Mb/s, full duplex
spi-ks8995 spi0.0: enable port 0
spi-ks8995 spi0.0: set KS8995_REG_PC2 for port 0 to 06
spi-ks8995 spi0.0 lan1: configuring for phy/mii link mode
spi-ks8995 spi0.0 lan1: Link is Up - 100Mbps/Full - flow control rx/tx
PING 169.254.1.1 (169.254.1.1): 56 data bytes
64 bytes from 169.254.1.1: seq=0 ttl=64 time=1.629 ms
64 bytes from 169.254.1.1: seq=1 ttl=64 time=0.951 ms
I also tested SSH from the device to the host and it works fine.
It also works fine to ping the device from the host and to SSH
into the device from the host.
This brings the ks8995 driver to a reasonable state where it can
be used from the current device tree bindings and the existing
device trees in the kernel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-4-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is some sysfs file to read and write registers randomly
in the ks8995 driver.
The contemporary way to achieve the same thing is to implement
regmap abstractions, if needed. Delete this and implement
regmap later if we want to be able to inspect individual registers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-3-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the datasheet we need to wait 100us before accessing
any registers in the KS8995 after a reset de-assertion.
Add this delay, if and only if we obtained a GPIO descriptor,
otherwise it is just a pointless delay.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-2-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By reading the datasheets for the KS8995 it is obvious that this
is a 100 Mbit DSA switch.
Let us start the refactoring by moving it to the DSA subsystem to
preserve development history.
Verified that the chip still probes the same after this patch
provided CONFIG_HAVE_NET_DSA, CONFIG_NET_DSA and CONFIG_DSA_KS8995
are selected.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250813-ks8995-to-dsa-v1-1-75c359ede3a5@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit
68e068cabd ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
kernel log output (truncated):
WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140
...
Call Trace:
<TASK>
skb_checksum_help+0x12a/0x1f0
validate_xmit_skb+0x1a3/0x2d0
validate_xmit_skb_list+0x4f/0x80
sch_direct_xmit+0x1a2/0x380
__dev_xmit_skb+0x242/0x670
__dev_queue_xmit+0x3fc/0x7f0
ip6_finish_output2+0x25e/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel]
ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre]
dev_hard_start_xmit+0x63/0x1c0
__dev_queue_xmit+0x6d0/0x7f0
ip6_finish_output2+0x214/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
inet6_csk_xmit+0xeb/0x150
__tcp_transmit_skb+0x555/0xa80
tcp_write_xmit+0x32a/0xe90
tcp_sendmsg_locked+0x437/0x1110
tcp_sendmsg+0x2f/0x50
...
skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e
skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00
skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00
skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00
skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00
skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00
skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9
skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01
skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a
Fixes: 04c20a9356 ("net: skip offload for NETIF_F_IPV6_CSUM if ipv6 header contains extension")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Suggested-by: Michal Schmidt <mschmidt@redhat.com>
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Jakub Ramaseuski <jramaseu@redhat.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250814105119.1525687-1-jramaseu@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8211F PHY has two modes for a single INTB/PMEB pin:
1. INTB mode, where it signals interrupts to the CPU, which can
include wake-on-LAN events.
2. PMEB mode, where it only signals a wake-on-LAN event, which
may either be a latched logic low until software manually
clears the WoL state, or pulsed mode.
In the case of (1), there is no way to know whether the interrupt to
which the PHY is connected is capable of waking the system. In the
case of (2), there would be no interrupt property in the PHY's DT
description, and thus there is nothing to describe whether the pin is
even wired to anything such as a power management controller.
There is a "wakeup-source" property which can be applied to any device
- see Documentation/devicetree/bindings/power/wakeup-source.txt
Case 1 above matches example 2 in this document, and case 2 above
matches example 3. Therefore, it seems reasonable to make use of this
existing specification, albiet it hasn't been converted to YAML.
Document the wakeup-source property in the device description, which
will indicate that the PHY has been wired up in such a way that it
can wake the system from a low power state.
We will use this in a rewrite of the existing broken Wake-on-Lan code
that was merged during the 6.16 merge window to support case 1. Case 2
can be added to the driver later without needing to further alter the
DT description. To be clear, the existing Wake-on-Lan code that was
recently merged has multiple functional issues.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/E1um9Xj-008kBx-72@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement Wake-on-Lan for RTL8211F correctly. The existing
implementation has multiple issues:
1. It assumes that Wake-on-Lan can always be used, whether or not the
interrupt is wired, and whether or not the interrupt is capable of
waking the system. This breaks the ability for MAC drivers to detect
whether the PHY WoL is functional.
2. switching the interrupt pin in the .set_wol() method to PMEB mode
immediately silences link-state interrupts, which breaks phylib
when interrupts are being used rather than polling mode.
3. the code claiming to "reset WOL status" was doing nothing of the
sort. Bit 15 in page 0xd8a register 17 controls WoL reset, and
needs to be pulsed low to reset the WoL state. This bit was always
written as '1', resulting in no reset.
4. not resetting WoL state results in the PMEB pin remaining asserted,
which in turn leads to an interrupt storm. Only resetting the WoL
state in .set_wol() is not sufficient.
5. PMEB mode does not allow software detection of the wake-up event as
there is no status bit to indicate we received the WoL packet.
6. across reboots of at least the Jetson Xavier NX system, the WoL
configuration is preserved.
Fix all of these issues by essentially rewriting the support. We:
1. clear the WoL event enable register at probe time.
2. detect whether we can support wake-up by having a valid interrupt,
and the "wakeup-source" property in DT. If we can, then we mark
the MDIO device as wakeup capable, and associate the interrupt
with the wakeup source.
3. arrange for the get_wol() and set_wol() implementations to handle
the case where the MDIO device has not been marked as wakeup
capable (thereby returning no WoL support, and refusing to enable
WoL support.)
4. avoid switching to PMEB mode, instead using INTB mode with the
interrupt enable, reconfiguring the interrupt enables at suspend
time, and restoring their original state at resume time (we track
the state of the interrupt enable register in .config_intr()
register.)
5. move WoL reset from .set_wol() to the suspend function to ensure
that WoL state is cleared prior to suspend. This is necessary
after the PME interrupt has been enabled as a second WoL packet
will not re-raise a previously cleared PME interrupt.
6. when a PME interrupt (for wakeup) is asserted, pass this to the
PM wakeup so it knows which device woke the system.
This fixes WoL support in the Realtek RTL8211F driver when used on the
nVidia Jetson Xavier NX platform, and needs to be applied before stmmac
patches which allow these platforms to forward the ethtool WoL commands
to the Realtek PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1um8Ld-008jxD-Mc@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use kvfree() to free memory allocated by kvzalloc() instead of kfree().
Avoid potential memory management issue considering kvzalloc() can
internally choose to use either kmalloc() or vmalloc() based on memory
request and current system memory state. Hence, use more appropriate
kvfree() which automatically determines correct free method to avoid
potential hard to debug memory issues. Fix this issue discovered by
running spatch static analysis tool using coccinelle script -
scripts/coccinelle/api/kfree_mismatch.cocci
Fixes: 52929c2142 ("fwctl/mlx5: Support for communicating with mlx5 fw")
Link: https://patch.msgid.link/r/aKAjCoF9cT3VEbSE@bhairav-test.ee.iitb.ac.in
Signed-off-by: Akhilesh Patil <akhilesh@ee.iitb.ac.in>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
On DCE 6, DP audio was not working. However, it worked when an
HDMI monitor was also plugged in.
Looking at dce_aud_wall_dto_setup it seems that the main
difference is that we use DTO1 when only DP is plugged in.
When programming DTO1, it uses audio_dto_source_clock_in_khz
which is set from get_dp_ref_freq_khz
The dce60_get_dp_ref_freq_khz implementation looks incorrect,
because DENTIST_DISPCLK_CNTL seems to be always zero on DCE 6,
so it isn't usable.
I compared dce60_get_dp_ref_freq_khz to the legacy display code,
specifically dce_v6_0_audio_set_dto, and it turns out that in
case of DCE 6, it needs to use the display clock. With that,
DP audio started working on Pitcairn, Oland and Cape Verde.
However, it still didn't work on Tahiti. Despite having the
same DCE version, Tahiti seems to have a different audio device.
After some trial and error I realized that it works with the
default display clock as reported by the VBIOS, not the current
display clock.
The patch was tested on all four SI GPUs:
* Pitcairn (DCE 6.0)
* Oland (DCE 6.4)
* Cape Verde (DCE 6.0)
* Tahiti (DCE 6.0 but different)
The testing was done on Samsung Odyssey G7 LS28BG700EPXEN on
each of the above GPUs, at the following settings:
* 4K 60 Hz
* 1080p 60 Hz
* 1080p 144 Hz
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 645cc7863d)
Cc: stable@vger.kernel.org
For later VBIOS versions, the fractional feedback divider is
calculated as the remainder of dividing the feedback divider by
a factor, which is set to 1000000. For reference, see:
- calculate_fb_and_fractional_fb_divider
- calc_pll_max_vco_construct
However, in case of old VBIOS versions that have
set_pixel_clock_v3, they only have 1 byte available for the
fractional feedback divider, and it's expected to be set to the
remainder from dividing the feedback divider by 10.
For reference see the legacy display code:
- amdgpu_pll_compute
- amdgpu_atombios_crtc_program_pll
This commit fixes set_pixel_clock_v3 by dividing the fractional
feedback divider passed to the function by 100000.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 027e7acc7e)
Cc: stable@vger.kernel.org
When getting the number of connectors, the VBIOS reports
the number of valid indices, but it doesn't say which indices
are valid, and not every valid index has an actual connector.
If we don't find a connector on an index, that is not an error.
Considering these are not actual errors, don't litter the logs.
Fixes: 60df562814 ("drm/amd/display: handle invalid connector indices")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 249d4bc5f1)
On some GPUs the VBIOS just doesn't have encoder caps,
or maybe not for every encoder.
This isn't really a problem and it's handled well,
so let's not litter the logs with it.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 33e0227ee9)
Also needed by DCE 6.
This way the code that gathers this info can be shared between
different DCE versions and doesn't have to be repeated.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8107432dff)
Cc: stable@vger.kernel.org
dce110_fill_display_configs is shared between DCE 6-11, and
finding the first CRTC and its line time is relevant to DCE 6 too.
Move the code to find it from DCE 11 specific code.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4ab09785f8)
Cc: stable@vger.kernel.org
Adjust the nominal (and performance) clocks for DCE 8-10,
and set them to 625 MHz, which is the value used by the legacy
display code in amdgpu_atombios_get_clock_info.
This was tested with Hawaii, Tonga and Fiji.
These GPUs can output 4K 60Hz (10-bit depth) at 625 MHz.
The extra 15% clock was added as a workaround for a Polaris issue
which uses DCE 11, and should not have been used on DCE 8-10 which
are already hardcoded to the highest possible display clock.
Unfortunately, the extra 15% was mistakenly copied and kept
even on code paths which don't affect Polaris.
This commit fixes that and also adds a check to make sure
not to exceed the maximum DCE 8-10 display clock.
Fixes: 8cd61c313d ("drm/amd/display: Raise dispclk value for Polaris")
Fixes: dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1ae45b5d4f)
The AXI crossbar of TH1520 has no proper timeout handling, which means
gating AXI clocks can easily lead to bus timeout and thus system hang.
Set all AXI clock gates to CLK_IS_CRITICAL. All these clock gates are
ungated by default on system reset.
In addition, convert all current CLK_IGNORE_UNUSED usage to
CLK_IS_CRITICAL to prevent unwanted clock gating.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The DPU pixel clock rate corresponds to the required dot clock of the
display mode, so it needs to be tweakable.
Add support to change it, by adding generic divider setting code,
arming the code to the dpu0/dpu1 clocks, and setting the pixel clock
connected to the DPU (after a gate) to CLK_SET_RATE_PARENT to propagate
it to the dividers.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The 2nd control word of T-Head TH1520 PLLs contains a bit to put the VCO
into reset state, which means disabling the PLL.
Some PLLs are put to disabled state by the bootloader, and the clock
driver should be able to enable them.
Add support for enabling/disabling PLLs. PLLs other than DPU ones are
set CLK_IS_CRITICAL to prevent killing the system -- they're meant to
drive CPU or system buses (even the GMAC/Video ones are driving arbitrary
buses).
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The dpu0_pixelclk and dpu1_pixelclk gates were incorrectly parented to
the video_pll_clk.
According to the TH1520 TRM, the "dpu0_pixelclk" should be sourced from
"DPU0 PLL DIV CLK". In this driver, "DPU0 PLL DIV CLK" corresponds to
the `dpu0_clk` clock, which is a divider whose parent is the
`dpu0_pll_clk`.
This patch corrects the clock hierarchy by reparenting `dpu0_pixelclk`
to `dpu0_clk`. By symmetry, `dpu1_pixelclk` is also reparented to its
correct source, `dpu1_clk`.
Fixes: 50d4b157fa ("clk: thead: Add clock support for VO subsystem in T-HEAD TH1520 SoC")
Reported-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
[Icenowy: add Drew's R-b and rebased atop ccu_gate refactor]
Reviewed-by: Drew Fustini <fustini@kernel.org>
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The padctrl0 clock seems to be a child of the perisys_apb4_hclk clock,
gating the later makes padctrl0 registers stuck too.
Fix this relationship.
Fixes: ae81b69fd2 ("clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks")
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Drew Fustini <fustini@kernel.org>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.dev>
Signed-off-by: Drew Fustini <fustini@kernel.org>
The extra 15% clock was added as a workaround for a Polaris issue
which uses DCE 11, and should not have been used on DCE 6 which
is already hardcoded to the highest possible display clock.
Unfortunately, the extra 15% was mistakenly copied and kept
even on code paths which don't affect Polaris.
This commit fixes that and also adds a check to make sure
not to exceed the maximum DCE 6 display clock.
Fixes: 8cd61c313d ("drm/amd/display: Raise dispclk value for Polaris")
Fixes: dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
Fixes: 3ecb3b794e ("drm/amd/display: dc/clk_mgr: add support for SI parts (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 427980c1cb)
Cc: stable@vger.kernel.org
The function mod_hdcp_hdcp1_create_session() calls the function
get_first_active_display(), but does not check its return value.
The return value is a null pointer if the display list is empty.
This will lead to a null pointer dereference.
Add a null pointer check for get_first_active_display() and return
MOD_HDCP_STATUS_DISPLAY_NOT_FOUND if the function return null.
This is similar to the commit c3e9826a22
("drm/amd/display: Add null pointer check for get_first_active_display()").
Fixes: 2deade5ede ("drm/amd/display: Remove hdcp display state with mst fix")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5e43eb3cd7)
[WHY & HOW]
IPS & self-fresh feature can cause vblank counter resets between
vblank disable and enable.
It may cause system stuck due to wait the vblank counter.
Call the drm_crtc_vblank_restore() during vblank enable to estimate
missed vblanks by using timestamps and update the vblank counter in
DRM.
It can make the vblank counter increase smoothly and resolve this issue.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sun peng (Leo) Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 34d66bc7ff)
Cc: stable@vger.kernel.org
