The ROHM BD79105 is a simple 16-bit ADC accessible via SPI*.
The BD79105 has a CONVSTART pin, which must be set high to start the ADC
conversion. Unlike with the ad7091 and ad7091r which also have a
CONVSTART pin, the BD79105 requires that the pin must remain high also
for the duration of the SPI access.
(*) Couple of words about the SPI. The BD79105 has pins named as
CONVSTART, SCLK, DIN and DOUT. For the curious reader, DIN is not SPI
ISO.
DIN is a signal which can be used as a chip-select. When DIN is pulled
low, the ADC will output the completed measurement via DOUT as SCLK is
clocked. According to the data-sheet, the DIN can also be used for
daisy-chaining multiple ADCs. Furthermore, DOUT can be used also for a
'data-ready' -IRQ. These modes aren't supported by this driver.
Support reading ADC scale and data from the BD79105 using SPI, when DIN
is used as a chip-select.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/6ee06d551256db9213ccbe72f44cfe9452717716.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79105 is a simple, 16-bit, 1-channel ADC with a 'CONVSTART'
pin used to start the ADC conversion. Other than the 'CONVSTART', there
are 3 supply pins (one used as a reference), analog inputs, ground and
communication pins. It's worth noting that the pin somewhat confusingly
labeled as 'DIN', is a pin which should be used as a chip-select. The IC
does not have any writable registers.
The device is designed so that the output pin can, in addition to
outputting the data, be used as a 'data-ready'-IRQ. There are cases
where the IRQ can't be used (because it is delivered via SPI data-line).
Hence, some systems may use a GPIO for polling the data readiness.
Add a compatible for the bd79105 and add the data-ready GPIO to the
binding.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/3f70f68665225be3091f8a0412e74037b6a2a88e.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 supports a few variants with different power-supplies and
control GPIOs. The binding first unconditionally introduces all the
properties, and later sets them 'true' or 'false' based on the
combatible.
The 'true' seems to be implied by the initial property introduction so
the 'true' -branches in later conditional handling (based on the
compatible) can be omitted.
Drop the redundant true -branches.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/bee66444bf628ba9a34a02738a1842e2abc14290.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 supports two IC variants which may have a 'convstart' -GPIO
for starting the conversion. Currently the driver calls a function which
tries to access the GPIO for all of the IC variants, whether they
support 'convstart' or not. This is not an error because this function
returns early if GPIO information is not populated.
We can do a tad better by calling this function only for the ICs which
have the 'convstart' by providing a function pointer to the convstart
function from the chip_info structure, and calling this function only
for the ICs which have the function pointer set.
This does also allow to support ICs which require different convstart
handling than the currently supported ICs.
Call convstart function only on the ICs which can support it and allow
IC-specific convstart functions for the ICs which require different
handling.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/9760cde888fac7335c17d7ab63d5fb2e7c59ac51.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 driver defines separate chan_spec structures for operation
with and without convstart GPIO. At quick glance this may seem as if the
driver did provide more than 1 data-channel to users - one for the
regular data, other for the data obtained with the convstart GPIO.
The only difference between the 'convstart' and 'non convstart'
-channels is presence / absence of the BIT(IIO_CHAN_INFO_RAW) in
channel's flags.
We can drop the convstart channel spec, and related convstart macro, by
allocating a mutable per driver instance channel spec and adding the flag
in probe if needed. This will simplify the driver with the cost of added
memory consumption.
Assuming there aren't systems with very many ADCs and very few
resources, this tradeoff seems worth making.
Simplify the driver by dropping the 'convstart' channel spec and
allocating the channel spec for each driver instance.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/cd7c72e3ee00f279d3381873f54e0c5b75b5ad11.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 driver supports ADCs which require a GPIO pin to be used to
start conversion. The GPIO line status seems to be always toggled from
a process context, either from the user-initiated "raw-read conversion",
or from a threaded IRQ handler. Furthermore, these ICs are connected via
SPI bus, which is usually implemented in a way that the access to the
device can sleep. The GPIO here is toggled from the same context which
is reading the results over SPI.
Thus it seems very likely these GPIOs are toggled from a context which
can sleep.
Swap the gpiod_set_value() to gpiod_set_value_cansleep() accordinlgy.
Suggested-by: Nuno Sá <noname.nuno@gmail.com>
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/a2d4b77e9739662797a1609f436b7f9807e1ac67.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 supports ADCs which use separate GPIO for starting the
conversion. For such devices, the driver uses different channel
information if the GPIO is found. The bit information is still always
used from the original (non 'convstart') channels.
This has not been causing problems because the bit information for the
'convstart' -channel and the 'normal' -channel is identical. It,
however, will cause issues if an IC has different characteristics for an
'convstart' -channel and regular channel. Furthermore, this will cause
problems if a device always requires the convstart GPIO and thus only
defines the convstart channel.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/70619e39023bc497ef68cc1eff11943ab68cbdf8.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 supports some ICs with an internal reference voltage. For
those ICs the reference voltage has been hard-coded as micro volts, but
the value which is later used in code needs to be milli volts. This
results the need to divide hard coded voltage by 1000 before using it.
Simplify code by changing the hard-coded voltage to millivolts and by
dropping the division.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/1c26529fcc039a3ce8b5a336948229ec727ee281.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 driver supports variants with different amount of supply
regulators. On some variants there is only VCC, which is used as a
reference voltage. Others have separate VREF regulator, and some rely on
internal VREF. Some have both internal VREF and option to connect
external one.
The ad7476 driver reads the regulator voltage only when the user asks to
get the scale. This means the driver needs to do some dancing while
picking the correct reference regulator (or internal reference), and
store it for the later use.
According to the discussion [1] variable voltage references are rare,
making it hard to justify the added complexity for supporting those.
Drop the support for the variable voltage references and simplify things
by using the managed regulator get and enable interfaces.
Link: https://lore.kernel.org/linux-iio/20250331122247.05c6b09d@jic23-huawei/#1
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: $URL #1
Link: https://patch.msgid.link/4a497cc5ac0f6506c1c94d10849e0ae1cacf1191.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7476 driver uses a table of structures for defining the IC variant
specific data. Table is indexed using enum values, which are picked by
SPI ID.
Having the table and an enum adds extra complexity and may encourage
adding IC specific quircks in the code, instead of centralizing the IC
differences in one place, the chip-info.
Simplify this by dropping the table and using individual structures for
the IC specific data, and storing the IC specific structure's address
directly in the SPI ID data. Finally, switch to the
spi_get_device_match_data() and add a check for the return value.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/9e179bb3ba52303448ae4a559c1f011acd3f2fa6.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add maintainer for Vishay veml6046x00 RGBIR color sensor driver and dt
binding.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Link: https://patch.msgid.link/20250728075447.338725-4-ak@it-klinger.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add Vishay VEML6046X00 high accuracy RGBIR color sensor.
This sensor provides three colour (red, green and blue) as well as one
infrared (IR) channel through I2C.
Support direct and buffered mode.
An optional interrupt for signaling green colour threshold underflow or
overflow is not supported so far.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Link: https://patch.msgid.link/20250728075447.338725-3-ak@it-klinger.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a new compatible for Vishay high accuracy RGBIR color sensor
veml6046x00.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Link: https://patch.msgid.link/20250728075447.338725-2-ak@it-klinger.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When `devm_add_action_or_reset()` fails, it is due to a failed memory
allocation and will thus return `-ENOMEM`. `dev_err_probe()` doesn't do
anything when error is `-ENOMEM`. Therefore, remove the useless call to
`dev_err_probe()` when `devm_add_action_or_reset()` fails, and just
return the value instead.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/pndectqm7te.a.out@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7994 supports external reference voltage on REFIN
pin so if a vref-supply has been defined it shall be
used.
Signed-off-by: Stefano Manni <stefano.manni@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250807074850.130831-3-stefano.manni@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If the chip supports an external reference voltage
on REFIN pin then the "vref-supply" regulator may be used.
This commit partially refactors 6b104e7895
to add the capability of the chip to have an external
voltage reference and then remove the ugly conditional check
on chip id.
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Stefano Manni <stefano.manni@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250807074850.130831-2-stefano.manni@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Describe the inactivity detection additionally using the free-fall
register. Due to the controversial discussions on the mailing list, this
section of the documentation will be committed separately to allow for a
more focused and detailed elaboration of the topic.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-8-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Inactivity and free-fall events are essentially the same type of sensor
events. Therefore, inactivity detection (normally set for periods between 1
and 255 seconds) can be extended for shorter durations to support free-fall
detection.
For periods shorter than 1 second, the driver automatically configures the
threshold and duration using the free-fall register. For periods longer
than 1 second, it uses the inactivity threshold and duration using the
inactivity registers.
When using the free-fall register, the link bit is not set, which means
auto-sleep cannot be enabled if activity detection is also active.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-6-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable AC/DC coupling configuration for activity and inactivity detection
by setting the AC/DC bit. Extend existing magnitude-based detection with
adaptive AC-coupled mode.
Use DC-coupled mode to compare acceleration samples directly against
configured thresholds. Use AC-coupled mode to compare samples against a
reference taken at the start of activity detection. Implement DC-coupled
events using MAG, and AC-coupled events using MAG_ADAPTIVE.
Expose configuration of thresholds and periods via separate sysfs handles.
Note that both coupling modes share the same sensor registers, so activity
or inactivity detection cannot be configured for both AC and DC
simultaneously. Apply the most recently configured mode.
Simplify event handling and support adaptive AC-coupling.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-5-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the sensor’s inactivity feature in the driver. When both
activity and inactivity detection are enabled, the sensor sets a link bit
that ties the two functions together. This also enables auto-sleep mode,
allowing the sensor to automatically enter sleep state upon detecting
inactivity.
Inactivity detection relies on a configurable threshold and a specified
time period. If sensor measurements remain below the threshold for the
defined duration, the sensor transitions to the inactivity state.
When an Output Data Rate (ODR) is set, the inactivity time period is
automatically adjusted to a sensible default. Higher ODRs result in shorter
inactivity timeouts, while lower ODRs allow longer durations-within
reasonable upper and lower bounds. This is important because features like
auto-sleep operate effectively only between 12.5 Hz and 400 Hz. These
defaults are applied when the sample rate is modified, but users can
override them by explicitly setting a custom inactivity timeout.
Similarly, configuring the g-range provides default threshold values for
both activity and inactivity detection. These are implicit defaults meant
to simplify configuration, but they can also be manually overridden as
needed.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-4-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable the sensor to detect activity and trigger interrupts accordingly.
Activity events are determined based on a threshold, which is initialized
to a sensible default during probe. This default value is adopted from the
legacy ADXL345 input driver to maintain consistent behavior.
The combination of activity detection, ODR configuration, and range
settings lays the groundwork for the activity/inactivity hysteresis
mechanism, which will be implemented in a subsequent patch. As such,
portions of this patch prepare switch-case structures to support those
upcoming changes.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-3-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify setting the tap suppress bit by applying regmap_assign_bit(). As a
result, the defines can be reorganized for better clarity.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Link: https://patch.msgid.link/20250727210014.27766-2-l.rubusch@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no txt file for it, add yaml for invensense,icp10100
which is already used in the driver. Also, document other compatibles
for ICP-101xx family and add invensense,icp10100 as a fallback.
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250801221424.132305-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for debugfs_reg_access through the driver's iio_info structure
to enable low-level register read/write access for debugging.
Signed-off-by: Akshay Jindal <akshayaj.lkd@gmail.com>
Link: https://patch.msgid.link/20250728161445.13261-1-akshayaj.lkd@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put the filter types in alphabetical order by name. This makes it easier
to find a specific filter type when looking through the documentation.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250710-iio-adc-ad7137-add-filter-support-v1-4-acffe401c4d2@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop the call to INIT_LIST_HEAD(&cb_buff->buffer.demux_list). That's
already done in iio_buffer_init(&cb_buff->buffer).
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250725-iio-minor-cleanup-v1-1-4e561372142e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver is getting clock and almost immediately enabling it, with the
devm_request_irq() as the only relevant code executed between, thus the
probe path and cleanups can be simplified with devm_clk_get_enabled().
Move devm_request_irq() earlier, so the interrupt handler will be
registered before clock is enabled. This might be important in case
regulator supplies are enabled by other device driver and this device
raises interrupt immediately after clock sarts ticking.
The change does not reverse cleanup paths - first regulator will be
disabled, then clock and finally interrupt handler freed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250713-iio-clk-get-enabled-v1-1-70abc1f9ce6c@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dynaimage,al3010 and dynaimage,al3320a are I2C devices, so their
interrupts are not routed to GIC and rarely first interrupt cell is <0>.
This looks like copy-paste from some SoC block, so drop it and also for
readability use known defines instead of hard-coding interrupt flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250724111345.47889-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The interrupt line to GIC is IRQ_TYPE_LEVEL_HIGH, so use that instead of
"none". Also replace the hard-coded GIC_SPI flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250724111345.47889-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For readability use known defines instead of hard-coding GPIO or
interrupt flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20250724111345.47889-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop includes of headers which example code does not use. No functional
impact.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Acked-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250724111345.47889-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change the ti-adc081c driver to use individual model structures instead
of an array. This reduces the verbosity of the code. Also, the data is
now const as it should have been in the first place. The ADCxx1C_MODEL()
macro is dropped to be consistent with similar model definitions in
other drivers.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250721-iio-const-data-11-v2-1-c3fec12511ee@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the scan struct to the stack instead of being in the driver state
struct. The buffer is only used in a single function and does not need
to be DMA-safe so it does not need to exist outside of that function's
scope.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250721-iio-use-more-iio_declare_buffer_with_ts-v2-1-f8fb11b8add8@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a stack allocated scan struct in srf08_trigger_handler(). Since the
scan buffer isn't used outside of this function and doesn't need to be
DMA-safe, it doesn't need to be in struct srf08_data. We can also
eliminate an extra local variable for the return value of
srf08_read_ranging() by using scan.chan directly.
Reviewed-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250721-iio-use-more-iio_declare_buffer_with_ts-6-v2-1-8b66e5b4e75a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a stack-allocated struct in sx9500_trigger_handler() to hold the
IIO buffer scan data. Since the scan buffer isn't used outside of this
function, it doesn't need to be in struct sx9500_data.
By always allocating enough space for the maximum number of channels,
we can avoid having to reallocate the buffer each time buffered reads
are enabled.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250722-iio-use-more-iio_declare_buffer_with_ts-4-v2-1-9e566f3a4c6a@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use a stack allocated struct for the scan data instead of using the
driver state to store the struct. The scan data is not used outside of
the interrupt handler function so the struct does not need to exist
outside of that scope.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250722-iio-proximity-mb1232-use-stack-allocated-scan-struct-v1-1-b4ef77e9ddea@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC controller in most Rockchip SoCs are part of power domains
that are always powered on, i.e. PD_BUS or PD_PERI. These always powered
on power domains have typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the power domain of the
SARADC controller.
On RK3528 the SARADC controller is part of the PD_VPU power domain.
Add support to describe an optional power-domains for the SARADC
controller in Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250723085654.2273324-4-jonas@kwiboo.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
avg sample info is a bit field coded inside the following
bits: 5,6,7 and 8 of a device status register.
Channel num info the same, but over bits: 1, 2 and 3.
Mask both values in order to avoid touching other register bits,
since the first info (avg sample), came from DT.
Signed-off-by: Rodrigo Gobbi <rodrigo.gobbi.7@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250717221559.158872-1-rodrigo.gobbi.7@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use kvfree() to fix the following Coccinelle/coccicheck warning reported
by kfree_mismatch.cocci:
WARNING kvmalloc is used to allocate this memory at line 10398
Fixes: f728c17fc9 ("accel/habanalabs/gaudi2: move HMMU page tables to device memory")
Reported-by: Qianfeng Rong <rongqianfeng@vivo.com>
Closes: https://patch.msgid.link/20250808085530.233737-1-rongqianfeng@vivo.com
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
[lukas: acknowledge Qianfeng, adjust Thorsten's domain, add Fixes tag]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
Cc: stable@vger.kernel.org # v6.9+
Link: https://patch.msgid.link/20240820231028.136126-1-thorsten.blum@toblux.com
